The pin id for a given tuple listed in a fsl,pins property is calculated
by dividing the first entry (which is also a register offset) by 4.
As the first available register is at offset 0x8 and configures the pad
MX25_PAD_A10 the right id for this pin is 2. All other pins are off by
one, too.

This patch drops the definition MX25_PAD_RESERVE1 (together with its
only use) and decrements all following values by 1.

Fixes: b4a87c9b ("pinctrl: pinctrl-imx: add imx25 pinctrl driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The right check for conf_reg to be invalid it testing against -1 not 0
as is done in the rest of the driver.

This fixes an oops that can be triggered by:

	cat /sys/kernel/debug/pinctrl/43fac000.iomuxc/*

Fixes: ae75ff81 ("pinctrl: pinctrl-imx: add imx pinctrl core driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The .pin_config_get/set operation are not supported in qcom pinctrl
driver. As the pinconf core is smart enough it doesn't complain
about that.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add initial pinctrl driver to support pin configuration with
pinctrl framework for msm8916.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Adds devicetree binding documentation.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On newer TLMM hardware blocks the registers are spread and
we need an offsets upper than 16 bits to address them. Increase
the register offset variables to 32 bits size.
Signed-off-by: Joonwoo Park <joonwoop@codeaurora.org>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The zynq and qcom-spmi pinctrl drivers both use pin_config_item arrays
to provide extra interfaces in debugfs. This structure and the
PCONFDUMP macro are not defined if CONFIG_DEBUG_FS is turned off,
so we get build errors like:

pinctrl/qcom/pinctrl-spmi-gpio.c:139:37: error: array type has incomplete element type
 static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = {
                                     ^
pinctrl/qcom/pinctrl-spmi-gpio.c:140:2: error: implicit declaration of function 'PCONFDUMP' [-Werror=implicit-function-declaration]
  PCONFDUMP(PMIC_GPIO_CONF_PULL_UP,  "pull up strength", NULL, true),
  ^
pinctrl/qcom/pinctrl-spmi-gpio.c:139:37: warning: 'pmic_conf_items' defined but not used [-Wunused-variable]
 static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = {

Lacking any better idea to solve this nicely, this patch uses #ifdef
to hide the structures, just like the pinctrl core does.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Rockchip GPIO interrupt controller totally throws away all status
about an interrupt when you "disable" the interrupt.  That has
unfortunate consequences in the following situation:

1. An edge-triggered interrupt is enabled and should wake the system.
2. System suspend happens: interrupt is disabled and marked for wake.
3. rockchip_irq_suspend() reenables the interrupt so we can wake.
4. Interrupt happens when asleep.
5. rockchip_irq_resume() redisables the interrupt.
6. Disabling the interrupt throws away all status about it.
7. Normal system resume happens and we enable the interrupt again,
   since we threw away status about the interrupt we don't know it
   fired while suspended.  Even worse: if we need both edges of the
   interrupt the logic to swap edges never runs.

Note: even if we somehow can post the status about wakeup interrupts
in rockchip_irq_resume() we would still have a window of losing any
edges that came in while interrupts were disabled.

If we use mask only then we don't need to worry.  The GPIO Interrupt
controller keeps track of pending interrupts that are enabled and just
masked.

There was no real strong reason to support the enable/disable
functionality (other than that it seemed right), so let's go back to
just supporting mask/unmask but actually map it to the real
mask/unmask.  This ends up with slightly different (and more correct)
behavior than before (f2dd028c pinctrl: rockchip: Fix
enable/disable/mask/unmask).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 3.19-rc6

Fix usb0 pin 19 -> 29 (matching ethernet1 pins and manual).
Pin 19 is used for ethernet0 on the Parallella board.

Fixes: add958ce ("pinctrl: Add driver for Zynq")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove the DT compatible string entry for the now unsupported sh7372 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Remove sh7372 PFC support as part of the sh7372 and Mackerel
legacy code removal.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add PFC support for the EMMA Mobile EV2 SoC including pin groups for
on-chip devices.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Used to define pinmux configurations where the pinmux function have no
representation in the configuration registers but instead solely depends
on a group selection.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.

GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull x86 fixes from Thomas Gleixner:
 "Hopefully the last round of fixes for 3.19

   - regression fix for the LDT changes
   - regression fix for XEN interrupt handling caused by the APIC
     changes
   - regression fixes for the PAT changes
   - last minute fixes for new the MPX support
   - regression fix for 32bit UP
   - fix for a long standing relocation issue on 64bit tagged for stable
   - functional fix for the Hyper-V clocksource tagged for stable
   - downgrade of a pr_err which tends to confuse users

  Looks a bit on the large side, but almost half of it are valuable
  comments"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsc: Change Fast TSC calibration failed from error to info
  x86/apic: Re-enable PCI_MSI support for non-SMP X86_32
  x86, mm: Change cachemode exports to non-gpl
  x86, tls: Interpret an all-zero struct user_desc as "no segment"
  x86, tls, ldt: Stop checking lm in LDT_empty
  x86, mpx: Strictly enforce empty prctl() args
  x86, mpx: Fix potential performance issue on unmaps
  x86, mpx: Explicitly disable 32-bit MPX support on 64-bit kernels
  x86, hyperv: Mark the Hyper-V clocksource as being continuous
  x86: Don't rely on VMWare emulating PAT MSR correctly
  x86, irq: Properly tag virtualization entry in /proc/interrupts
  x86, boot: Skip relocs when load address unchanged
  x86/xen: Override ACPI IRQ management callback __acpi_unregister_gsi
  ACPI: pci: Do not clear pci_dev->irq in acpi_pci_irq_disable()
  x86/xen: Treat SCI interrupt as normal GSI interrupt

Pull irq fixes from Thomas Gleixner:
 "From the irqchip departement you get:

   - regression fix for omap-intc

   - regression fix for atmel-aic-common

   - functional correctness fix for hip04

   - type mismatch fix for gic-v3-its

   - proper error pointer check for mtd-sysirq

  Mostly one and two liners except for the omap regression fix which is
  slightly larger than desired"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip: atmel-aic-common: Prevent clobbering of priority when changing IRQ type
  irqchip: omap-intc: Fix legacy DMA regression
  irqchip: gic-v3-its: Fix use of max with decimal constant
  irqchip: hip04: Initialize hip04_cpu_map to 0xffff
  irqchip: mtk-sysirq: Use IS_ERR() instead of NULL pointer check

Pull timer fixes from Thomas Gleixner:
 "A set of small fixes:

   - regression fix for exynos_mct clocksource

   - trivial build fix for kona clocksource

   - functional one liner fix for the sh_tmu clocksource

   - two validation fixes to prevent (root only) data corruption in the
     kernel via settimeofday and adjtimex.  Tagged for stable"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: adjtimex: Validate the ADJ_FREQUENCY values
  time: settimeofday: Validate the values of tv from user
  clocksource: sh_tmu: Set cpu_possible_mask to fix SMP broadcast
  clocksource: kona: fix __iomem annotation
  clocksource: exynos_mct: Fix bitmask regression for exynos4_mct_write

Pull ARM SoC fixes from Olof Johansson:
 "A week's worth of fixes for various ARM platforms.  Diff wise, the
  largest fix is for OMAP to deal with how GIC now registers interrupts
  (irq_domain_add_legacy() -> irq_domain_add_linear() changes).

  Besides this, a few more renesas platforms needed the GIC instatiation
  done for legacy boards.  There's also a fix that disables coherency of
  mvebu due to issues, and a few other smaller fixes"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: add baud rate to Juno stdout-path
  ARM: dts: imx25: Fix PWM "per" clocks
  bus: mvebu-mbus: fix support of MBus window 13
  Merge tag 'mvebu-fixes-3.19-3' of git://git.infradead.org/linux-mvebu into fixes
  ARM: mvebu: completely disable hardware I/O coherency
  ARM: OMAP: Work around hardcoded interrupts
  ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
  ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
  arm: boot: dts: dra7: enable dwc3 suspend PHY quirk

Pull vfs fixes from Al Viro:
 "A couple of fixes - deadlock in CIFS and build breakage in cris serial
  driver (resurfaced f_dentry in there)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  VFS: Convert file->f_dentry->d_inode to file_inode()
  fix deadlock in cifs_ioctl_clone()

Pull device mapper fixes from Mike Snitzer:
 "Two stable fixes for dm-cache and one 3.19 DM core fix:

   - fix potential for dm-cache metadata corruption via stale metadata
     buffers being used when switching an inactive cache table to
     active; this could occur due to each table having it's own bufio
     client rather than sharing the client between tables.

   - fix dm-cache target to properly account for discard IO while
     suspending otherwise IO quiescing could complete prematurely.

   - fix DM core's handling of multiple internal suspends by maintaining
     an 'internal_suspend_count' and only resuming the device when this
     count drops to zero"

* tag 'dm-3.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix handling of multiple internal suspends
  dm cache: fix problematic dual use of a single migration count variable
  dm cache: share cache-metadata object across inactive and active DM tables

Pull two block layer fixes from Jens Axboe:
 "Two small patches that should make it into 3.19:

   - a fixup from me for NVMe, making the cq_vector a signed variable.
     Otherwise our -1 comparison fails, and commit 2b25d981 doesn't
     do what it was supposed to.

   - a fixup for the hotplug handling for blk-mq from Ming Lei, using
     the proper kobject referencing to ensure we release resources at
     the right time"

* 'for-linus' of git://git.kernel.dk/linux-block:
  blk-mq: fix hctx/ctx kobject use-after-free
  NVMe: cq_vector should be signed

pULL SCSI fixes from James Bottomley:
 "This consists of four real fixes and three MAINTAINER updates.

  Three of the fixes are obvious (the DIX and atomic allocation are bug
  on and warn on fixes and the other is just trivial) and the ipr one is
  a bit more involved but is required because without it, the card
  double completes aborted commands and causes a kernel oops"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  MAINTAINERS: ibmvscsi driver maintainer change
  MAINTAINERS: ibmvfc driver maintainer change
  MAINTAINERS: Remove self as isci maintainer
  scsi_debug: test always evaluates to false, || should be used instead
  scsi: Avoid crashing if device uses DIX but adapter does not support it
  scsi_debug: use atomic allocation in resp_rsup_opcodes
  ipr: wait for aborted command responses

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix reboot issues with the imx2_wdt driver and it also drops
  some forgotten owner assignments from platform_drivers"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: drop owner assignment from platform_drivers
  watchdog: imx2_wdt: Disable power down counter on boot
  watchdog: imx2_wdt: Improve power management support.

Pull hwmon update from Jean Delvare:
 "This contains a single thing: a new driver for the temperature sensor
  embedded in the Intel 5500/5520/X58 chipsets.

  Sorry for the late request, it's been so long since I last sent a pull
  request and I've been so busy with other tasks meanwhile that I simply
  forgot about these patches.  But given that this is a new driver, it
  can't introduce any regression so I thought it could still be OK.

  This has been in linux-next for months now"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (i5500_temp) Convert to use ATTRIBUTE_GROUPS macro
  hwmon: (i5500_temp) Convert to module_pci_driver
  hwmon: (i5500_temp) Don't bind to disabled sensors
  hwmon: (i5500_temp) Convert to devm_hwmon_device_register_with_groups
  hwmon: (i5500_temp) New driver for the Intel 5500/5520/X58 chipsets

Pull media fixes from Mauro Carvalho Chehab:
  - fix some race conditions caused by a regression on videobuf2
  - fix a interrupt release bug on cx23885
  - fix support for Mygica T230 and HVR4400
  - fix compilation breakage when USB is not selected on tlg2300
  - fix capabilities report on ompa3isp, soc-camera, rcar_vin and
    pvrusb2

* tag 'media/v3.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] omap3isp: Correctly set QUERYCAP capabilities
  [media] cx23885: fix free interrupt bug
  [media] pvrusb2: fix missing device_caps in querycap
  [media] vb2: fix vb2_thread_stop race conditions
  [media] rcar_vin: Update device_caps and capabilities in querycap
  [media] soc-camera: fix device capabilities in multiple camera host drivers
  [media] Fix Mygica T230 support
  [media] cx23885: Split Hauppauge WinTV Starburst from HVR4400 card entry
  [media] tlg2300: Fix media dependencies

Commit ffcc3936 ("dm: enhance internal suspend and resume interface")
attempted to handle multiple internal suspends on the same device, but
it did that incorrectly.  When these functions are called in this order
on the same device the device is no longer suspended, but it should be:
	dm_internal_suspend_noflush
	dm_internal_suspend_noflush
	dm_internal_resume

Fix this bug by maintaining an 'internal_suspend_count' and resuming
the device when this count drops to zero.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>

Use ATTRIBUTE_GROUPS macro to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>

Use module_pci_driver to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <jdelvare@suse.de>

On many motherboards, for an unknown reason, the thermal sensor seems
to be disabled and will return a constant temperature value of 36.5
degrees Celsius. Don't bind to the device in that case, so that we
don't report this bogus value to userspace.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>

Use devm_hwmon_device_register_with_groups() to simplify the code a
bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>

The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.

Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Romain Dolbeau <romain@dolbeau.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>

Pull btrfs fixes from Chris Mason:
 "We have a few fixes in my for-linus branch.

  Qu Wenruo's batch fix a regression between some our merge window pull
  and the inode_cache feature.  The rest are smaller bugs"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Don't call btrfs_start_transaction() on frozen fs to avoid deadlock.
  btrfs: Fix the bug that fs_info->pending_changes is never cleared.
  btrfs: fix state->private cast on 32 bit machines
  Btrfs: fix race deleting block group from space_info->ro_bgs list
  Btrfs: fix incorrect freeing in scrub_stripe
  btrfs: sync ioctl, handle errors after transaction start

Merge tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86

Pull platform driver fix from Darren Hart:
 "Revert keyboard backlight sysfs support and documentation.

  The support for the dell-laptop keyboard backlight was flawed and the
  fix:

        https://lkml.org/lkml/2015/1/14/539

  was more invasive that I felt comfortable sending at RC5.

  This series reverts the support for the dell-laptop keyboard backlight
  as well as the documentation for the newly created sysfs attributes.

  We'll get this implemented correctly for 3.20"

* tag 'platform-drivers-x86-v3.19-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
  Revert "platform: x86: dell-laptop: Add support for keyboard backlight"
  Revert "Documentation: Add entry for dell-laptop sysfs interface"

Pull PCI fixes from Bjorn Helgaas:
 "These are fixes for:

   - a resource management problem that causes a Radeon "Fatal error
     during GPU init" on machines where the BIOS programmed an invalid
     Root Port window.  This was a regression in v3.16.

   - an Atheros AR93xx device that doesn't handle PCI bus resets
     correctly.  This was a regression in v3.14.

   - an out-of-date email address"

* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Update Richard Zhu's email address
  sparc/PCI: Clip bridge windows to fit in upstream windows
  powerpc/PCI: Clip bridge windows to fit in upstream windows
  parisc/PCI: Clip bridge windows to fit in upstream windows
  mn10300/PCI: Clip bridge windows to fit in upstream windows
  microblaze/PCI: Clip bridge windows to fit in upstream windows
  ia64/PCI: Clip bridge windows to fit in upstream windows
  frv/PCI: Clip bridge windows to fit in upstream windows
  alpha/PCI: Clip bridge windows to fit in upstream windows
  x86/PCI: Clip bridge windows to fit in upstream windows
  PCI: Add pci_claim_bridge_resource() to clip window if necessary
  PCI: Add pci_bus_clip_resource() to clip to fit upstream window
  PCI: Pass bridge device, not bus, when updating bridge windows
  PCI: Mark Atheros AR93xx to avoid bus reset
  PCI: Add flag for devices where we can't use bus reset

Pull devicetree bug fixes and documentation updates from Grant Likely:
 "A few bugfixes for the new DT overlay feature, documentation updates,
  spelling corrections, and changes to MAINTAINERS.  Nothing earth
  shattering here"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  of/unittest: Overlays with sub-devices tests
  of/platform: Handle of_populate drivers in notifier
  of/overlay: Do not generate duplicate nodes
  devicetree: document the "qemu" and "virtio" vendor prefixes
  devicetree: document ARM bindings for QEMU's Firmware Config interface
  Documentation: of: fix typo in graph bindings
  dma-mapping: fix debug print to display correct dma_pfn_offset
  of: replace Asahi Kasei Corp vendor prefix
  ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
  dt/bindings: arm-boards: Spelling s/pointong/pointing/
  MAINTAINERS: Update DT website and git repository
  MAINTAINERS: drop DT regex matching on of_get_property and of_match_table

Merge tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: imx: fixes for 3.19, 2nd round" from Shawn Guo:

The i.MX fixes for 3.19, 2nd round:
 - Correct pwm clock assignment in i.MX25 device tree to fix the broken
   pwm support on i.MX25

* tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx25: Fix PWM "per" clocks
Signed-off-by: Olof Johansson <olof@lixom.net>

Without explicit command-line parameters, the Juno UART ends up running
at 57600 baud in the kernel, which is at odds with the 115200 baud used
by the rest of the firmware. Since commit 7914a7c5 now lets us
fix this by specifying default options in stdout-path, do so.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge "mvebu/fixes #3" from Andrew Lunn:

mvebu fixes for 3.19. (Part 4)

bus: mvebu-mbus: fix support of MBus window 13

* tag 'mvebu-fixes-3.19-4' of git://git.infradead.org/linux-mvebu:
  bus: mvebu-mbus: fix support of MBus window 13
  ARM: mvebu: completely disable hardware I/O coherency
Signed-off-by: Olof Johansson <olof@lixom.net>