Original FW only allowed us to perform ECN marking.  Newer releases
also support plain old drop.  Add the ability to configure drop
policy.  This is particularly useful in combination with GRED,
because different bands can have different ECN marking setting.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use offload of very simple u32 filters to direct packets to GRED
bands based on the DSCP marking.  No u32 hashing is supported,
just plain simple filters matching on ToS or Priority with
appropriate mask device can support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Learn how to set the DSCP map.  FW uses a packed array which
geometry depends on the number of supported priorities and
virtual queues.  Write code to assemble this map and to communicate
the setting to the FW via mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for PRIO offload calculate how long the prio map
for FW will be and make sure the configuration can be performed
via the vNIC mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of egress offloads the class/flowid assigned by the filter
may be very important for offloaded Qdisc selection.  Provide this
info to drivers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for GRED offload.  It behaves much like RED, but
can apply different parameters to different bands.  GRED operates
pretty much exactly like our HW/FW with a single FIFO and different
RED state instances.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wrap RED parameters and stats into a structure, and a 1-element
array.  Upcoming GRED offload will add the support for more bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow drivers which offload GRED to report back statistics.  Since
A lot of GRED stats is fairly ad hoc in nature pass to drivers the
standard struct gnet_stats_basic/gnet_stats_queue pairs, and
untangle the values in the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic offload for the GRED Qdisc.  Inform the drivers any
time Qdisc or virtual queue configuration changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add up stats for all bands for the extra ethtool statistics.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In PRIO-enabled FW read the statistics from per-band symbol, rather
than from the standard per-PCIe-queue counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the threshold table is large enough to hold information
for all bands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for per-band RED offload pass band parameter to
functions.  For now it will always be 0.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation for multi-band RED offload if FW is capable map
the extended symbols which will allow us to set per-band parameters
and read stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before setting tm related configuration to hardware, driver
needs to check the configuration provided by user is valid.
Currently hclge_ieee_setets and hclge_setup_tc both implement
their own checking, which has a lot in common.

This patch addes hclge_dcb_common_validate to do the common
checking. The checking in hclge_tm_prio_tc_info_update
and hclge_tm_schd_info_update is unnecessary now, so change
the return type to void, which removes the need to do error
handling when one of the checking fails.

Also, ets->prio_tc is indexed by user prio and ets->tc_tsa is
indexed by tc num, so this patch changes them to use different
index.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
selftests: Add tests for VXLAN at an 802.1d bridge

Petr says:

This patchset adds several tests for VXLAN attached to an 802.1d bridge
and fixes a related bug.

First patch #1 fixes a bug in propagating SKB already-forwarded marks
over veth to bridges, where they are irrelevant. This bug causes the
vxlan_bridge_1d test suite from this patchset to fail as the packets
aren't forwarded by br2.

In patches #2 and #3, lib.sh is extended to support network namespaces.
The use of namespaces is necessitated by VXLAN, which allows only one
VXLAN device with a given VNI per namespace. Thus to host full topology
on a single box for selftests, the "remote" endpoints need to be in
namespaces.

In patches #4-#6, lib.sh is extended in other ways to facilitate the
following patches.

In patches #7-#15, first the skeleton, and later the generic tests
themselves are added.

Patch #16 then adds another test that serves as a wrapper around the
previous one, and runs it with a non-default port number.

Patches #17 and #18 add mlxsw-specific tests. About those, Ido writes:

The first test creates various configurations with regards to the VxLAN
and bridge devices and makes sure the driver correctly forbids
unsupported configuration and permits supported ones. It also verifies
that the driver correctly sets the offload indication on FDB entries and
the local route used for VxLAN decapsulation.

The second test verifies that the driver correctly configures the singly
linked list used to flood BUM traffic and that traffic is flooded as
expected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to three IPv4 addresses of remote VTEPs. The test
verifies that packets are correctly flooded in various cases such as
deletion of a record in the middle of the list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test various aspects of VxLAN offloading which are specific to mlxsw,
such as sanitization of invalid configurations and offload indication.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This simple wrapper reruns the VXLAN ping test with a port number of
8472.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when decapsulating from VXLAN, the values of inner and outer
TOS are handled appropriately. Because VXLAN driver on its own won't
produce the arbitrary TOS combinations necessary to test this feature,
simply open-code a single ICMP packet and have mausezahn assemble it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that ECN bits in the VXLAN envelope are correctly deduced from the
overlay packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that TOS is inherited from the tunneled packet into the envelope as
configured at the VXLAN device.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This tests whether TTL of VXLAN envelope packets is properly set based
on the device configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ordering of the topology creation can have impact on whether a
driver is successful in offloading VXLAN. Therefore add a pseudo-test
that reshuffles bits of the topology, and then reruns the same suite of
tests again to make sure that the new setup is supported as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when sending traffic to a learned MAC address, the traffic is
forwarded accurately only to the right endpoint.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that when sending traffic to an unlearned MAC address, the traffic
is flooded to both remote VXLAN endpoints.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test end-to-end reachability between local and remote endpoints.

Note that because learning is disabled on the VXLAN device, the ICMP
requests will end up being flooded to all remotes.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This skeleton sets up a topology with three VXLAN endpoints: one
"local", possibly offloaded, and two "remote", formed using veth pairs
and likely purely software bridges. The "local" endpoint is connected to
host systems by a VLAN-unaware bridge.

Since VXLAN tunnels must be unique per namespace, each of the "remote"
endpoints is in its own namespace. H3 forms the bridge between the three
domains.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Such a function will be useful for counting malformed packets in the ECN
decap test.

To that end, introduce a common handler for handling stat-fetching, and
reuse it in link_stats_tx_packets_get() and link_stats_rx_errors_get().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the ping routine more generic by allowing passing arbitrary ping
command-line arguments.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Have ping_test() recognize an optional argument with a description of
the test. This is handy if there are several ping test, to make it clear
which is which.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to run a certain command inside another network namespace, it's
possible to use "ip netns exec ns command". However then one can't use
functions defined in lib.sh or a test suite.

One option is to do "ip netns exec ns bash -c command", provided that
all functions that one wishes to use (and their dependencies) are
published using "export -f". That may not be practical.

Therefore, introduce a helper in_ns(), which wraps a given command in a
boilerplate of "ip netns exec" and "source lib.sh", thus making all
library functions available. (Custom functions that a script wishes to
run within a namespace still need to be exported.)

Because quotes in "$@" aren't recognized in heredoc, hand-expand the
array in an explicit for loop, leveraging printf %q to handle proper
quoting.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far the case of NUM_NETIFS of 0 has not been interesting. However if
one wishes to reuse the lib.sh routines in a setup of a separate
namespace, being able to import like this is handy.

Therefore replace the {1..$NUM_NETIFS} references, which cause iteration
over 1 and 0, with an explicit for loop like we do in setup_wait() and
tc_offload_check(), so that for NUM_NETIFS of 0 no iteration is done.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a packet is trapped and the corresponding SKB marked as
already-forwarded, it retains this marking even after it is forwarded
across veth links into another bridge. There, since it ingresses the
bridge over veth, which doesn't have offload_fwd_mark, it triggers a
warning in nbp_switchdev_frame_mark().

Then nbp_switchdev_allowed_egress() decides not to allow egress from
this bridge through another veth, because the SKB is already marked, and
the mark (of 0) of course matches. Thus the packet is incorrectly
blocked.

Solve by resetting offload_fwd_mark() in skb_scrub_packet(). That
function is called from tunnels and also from veth, and thus catches the
cases where traffic is forwarded between bridges and transformed in a
way that invalidates the marking.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
octeontx2-af: NPC MCAM support and FLR handling

This patchset is a continuation to earlier submitted three patch
series to add a new driver for Marvell's OcteonTX2 SOC's
Resource virtualization unit (RVU) admin function driver.

1. octeontx2-af: Add RVU Admin Function driver
   https://www.spinics.net/lists/netdev/msg528272.html
2. octeontx2-af: NPA and NIX blocks initialization
   https://www.spinics.net/lists/netdev/msg529163.html
3. octeontx2-af: NPC parser and NIX blocks initialization
   https://www.spinics.net/lists/netdev/msg530252.html

This patch series adds support for below
RVU generic:
- Function Level Reset irq handler
  When FLR is triggered for PFs, AF receives interrupt.
  This patchset adds logic for cleaning up of NPA, NIX
  and NPC block resources being used by PF.

- Mailbox communication between AF and it's VFs.
  Unlike VFs of PF1-PFn, AF which is PF0 can communicate
  with it's VFs directly. Added support for the same.

- AF's VFs IO configuration
  These VFs are mapped to use internal HW loopback channels
  instead of CGX LMACs. Each pair of VFs work as two of ends
  of hardwired interfaces. VF0's TX is VF1's Rx & viceversa.

NPC block:
- MCAM entry management
  Alloc/Free of contiguous/non-contiguous and lower/higher
  priority MCAM entry allocation and programming support.
- MCAM counters management and map/unmap with MCAM entries
- Default KEY extract profile
- HW errata workarounds

NIX block:
- Minimum and maximum allowed packet length config
- HW errata workarounds

Few more changes like shift to use mutex instead of spinlock etc
are done in this patchset.

Changes from v2:
 1 Fixed commit message of patch 'Relax resource lock into mutex'
   to a more unambiguous one.
   - Suggested by David Miller.

Changes from v1:
 1 Converted all mailbox message handler API names to small letters
   from mixed small and capital letters.
   - Suggested by David Miller.
 2 Fixed endian issues in patch 'Add support for stripping STAG/CTAG'
   - Suggested by Arnd Bergmann
 3 Elaborated commit message of patch 'Add FLR interrupt handler'
   to make it a bit more easy to understand.
   - Suggested by Arnd Bergmann

 Will fix the padding and alignment in mailbox message structure
 in a follow-up patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Errata 35038
  Software sets NIX_AF_RX_SW_SYNC[ENA] to sync (flush) in-flight packets
  the RX data path before configuration changes (e.g. disabling one or
  more RQs). Hardware clears [ENA] to indicate sync is done

  An issue exists whereby NIX may clear NIX_AF_RX_SW_SYNC [ENA] too
  early.

Errata 35057
  NIX may corrupt internal state when conditional clocks turn off.
  So turnon all clocks by default.

Errata 35786
 Parse nibble enable NPC configuration for KEY generation has to be
 identical for both Rx and Tx interfaces.

Also corrected endianness configuration for NIX i.e NIX_AF_CFG[AF_BE]
is bit8 and not bit1.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Add interrupt handlers for Master Enable events from PFs
  and Master Enable events from VFs of AF
- Master Enable is required for the MSIX delivery to work
- Master Enable bit trap handler doesn't have to do any anything
  other than clearing the TRPEND bit, since the enable/disable
  requirements are already taken care using mbox requests/flr handler.
Signed-off-by: Linu Cherian <lcherian@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added support to handle FLR for AF's VFs (i.e LBK VFs).
Just the FLR interrupt enable/disable, handler registration
etc, actual HW resource cleanup or LFs teardown logic is
already there.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Configure AF VFs such that they are able to talk over consecutive
loopback channels.

If 8 VFs are attached to AF then communication will work as below:

TX      RX
lbk0 -> lbk1
lbk1 -> lbk0

lbk2 -> lbk3
lbk3 -> lbk2

lbk4 -> lbk5
lbk5 -> lbk4

lbk6 -> lbk7
lbk7 -> lbk6
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Enable all AF VFs during probe. Since AF's VFs work in pairs
(eg: Pkts sent on VF0 are received by VF1 and viceversa),
enable only even number of VFs out of totalVFs, which should
again be less than number of loopback (LBK) channels.

Also enable VF's mailbox interrupts.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>