* topic/huang-d3cold-v7:
  PCI/PM: add PCIe runtime D3cold support
  PCI: do not call pci_set_power_state with PCI_D3cold
  PCI/PM: add runtime PM support to PCIe port
  ACPI/PM: specify lowest allowed state for device sleep state

This patch adds runtime D3cold support and corresponding ACPI platform
support.  This patch only enables runtime D3cold support; it does not
enable D3cold support during system suspend/hibernate.

D3cold is the deepest power saving state for a PCIe device, where its main
power is removed.  While it is in D3cold, you can't access the device at
all, not even its configuration space (which is still accessible in D3hot).
Therefore the PCI PM registers can not be used to transition into/out of
the D3cold state; that must be done by platform logic such as ACPI _PR3.

To support wakeup from D3cold, a system may provide auxiliary power, which
allows a device to request wakeup using a Beacon or the sideband WAKE#
signal.  WAKE# is usually connected to platform logic such as ACPI GPE.
This is quite different from other power saving states, where devices
request wakeup via a PME message on the PCIe link.

Some devices, such as those in plug-in slots, have no direct platform
logic.  For example, there is usually no ACPI _PR3 for them.  D3cold
support for these devices can be done via the PCIe Downstream Port leading
to the device.  When the PCIe port is powered on/off, the device is powered
on/off too.  Wakeup events from the device will be notified to the
corresponding PCIe port.

For more information about PCIe D3cold and corresponding ACPI support,
please refer to:

- PCI Express Base Specification Revision 2.0
- Advanced Configuration and Power Interface Specification Revision 5.0

[bhelgaas: changelog]
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI subsystem has not been ready for D3cold support yet.  So
PCI_D3cold should not be used as parameter for pci_set_power_state.
This patch is needed for upcoming PCI_D3cold support.

This patch has no functionality change, because pci_set_power_state
will bound the parameter to PCI_D3hot too.

CC: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
CC: Jesse Barnes <jesse.barnes@intel.com>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

This patch adds runtime PM support to PCIe port.  This is needed by
PCIe D3cold support, where PCIe device without ACPI node may be
powered on/off by PCIe port.

Because runtime suspend is broken for some chipsets, a black list is
used to disable runtime PM support for these chipsets.
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Lower device sleep state can save more power, but has more exit
latency too.  Sometimes, to satisfy some power QoS and other
requirement, we need to constrain the lowest device sleep state.

In this patch, a parameter to specify lowest allowed state for
acpi_pm_device_sleep_state is added.  So that the caller can enforce
the constraint via the parameter.

This is needed by PCIe D3cold support, where the lowest power state
allowed may be D3_HOT instead of default D3_COLD.

CC: Len Brown <lenb@kernel.org>
CC: linux-acpi@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/jiang-mmconfig-v10:
  ACPI: mark acpi_sfi_table_parse() as __init
  x86/PCI: use pr_level() to replace printk(KERN_LEVEL)
  x86/PCI: refine __pci_mmcfg_init() for better code readability
  x86/PCI: get rid of redundant log messages
  x86/PCI: simplify pci_mmcfg_late_insert_resources()
  x86/PCI: update MMCONFIG information when hot-plugging PCI host bridges
  PCI/ACPI: provide MMCONFIG address for PCI host bridges
  x86/PCI: add pci_mmconfig_insert()/delete() for PCI root bridge hotplug
  x86/PCI: prepare pci_mmcfg_check_reserved() to be called at runtime
  x86/PCI: introduce pci_mmcfg_arch_map()/pci_mmcfg_arch_unmap()
  x86/PCI: use RCU list to protect mmconfig list
  x86/PCI: split out pci_mmconfig_alloc() for code reuse
  x86/PCI: split out pci_mmcfg_check_reserved() for code reuse

Mark function acpi_sfi_table_parse() as __init to avoid warning messages:

WARNING: vmlinux.o(.text+0x4cd2d2): Section mismatch in reference from the
function acpi_sfi_table_parse.clone.0() to the function

Function acpi_sfi_table_parse() calls acpi_table_parse() and
pci_parse_mcfg(), which are both marked as __init.  Currently
acpi_sfi_table_parse() is only used by MMCONFIG to scan MCFG table
at boot time only, so it's safe to mark acpi_sfi_table_parse() as __init.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/bjorn-trivial:
  PCI: remove useless pcix_set_mmrbc() dev->bus check
  PCI: acpiphp: check whether _ADR evaluation succeeded
  PCI: shpchp: remove dead code
  PCI: fix P2P bridge I/O port window sign extension
  PCI: fix upstream P2P bridge checks when enabling OBFF and LTR
  PCI: use __weak consistently
  PCI: cleanup assign_requested_resources_sorted() kernel-doc warning
  sparc/PCI: remove unused pcibios_assign_resource() definition

* topic/fixes-for-3.5:
  MAINTAINERS: correct PCI git tree address

Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Script checkpatch.pl recommends to replace printk(KERN_LVL) with pr_lvl(),
so do it.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Refine __pci_mmcfg_init() for better code readability.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

For each resource of a PCI host bridge, the arch code and PCI
code log following messages.  We don't need both, so drop the
arch-specific printing.

    pci_root PNP0A08:00: host bridge window [io 0x0000-0x03af]
    pci_bus 0000:00: root bus resource [io  0x0000-0x03af]
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Reduce redundant code to simplify pci_mmcfg_late_insert_resources().
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

This patch enhances x86 arch-specific code to update MMCONFIG information
when PCI host bridge hotplug event happens.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

This patch provide MMCONFIG address for PCI host bridges, which will
be used to support host bridge hotplug.  It gets MMCONFIG address
by evaluating _CBA method if available.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Introduce pci_mmconfig_insert()/pci_mmconfig_delete(), which will be used
to update MMCONFIG information when supporting PCI root bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Prepare function pci_mmcfg_check_reserved() to be called at runtime
for PCI host bridge hot-plugging
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Introduce pci_mmcfg_arch_map()/pci_mmcfg_arch_unmap(), which will be used
when supporting PCI root bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Use RCU list to protect mmconfig list from dynamic change
when supporting PCI host bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Split out pci_mmconfig_alloc() for code reuse, which will be used
when supporting PCI root bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Split out pci_mmcfg_check_reserved() for code reuse, which will be used
when supporting PCI host bridge hotplug.
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <liuj97@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

For a valid pci_dev, dev->bus != NULL always, so remove this
unnecessary test.

Found by Coverity (CID 101680).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Check whether we evaluated _ADR successfully.  Previously we ignored
failure, so we would have used garbage data from the stack as the device
and function number.

We return AE_OK so that we ignore only this slot and continue looking
for other slots.

Found by Coverity (CID 113981).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

"slots_not_empty" is initialized to zero and can't be set again before
reaching this point, so this return statement is dead.  Remove it.

Found by Coverity (CID 114324).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

On P2P bridges with 32-bit I/O decoding, we incorrectly sign-extended
windows starting at 0x80000000 or above.  In "base |= (io_base_hi << 16)",
"io_base_hi" is promoted to a signed int before being extended to an
unsigned long.

This would cause a window starting at I/O address 0x80000000 to be
treated as though it started at 0xffffffff80008000 instead, which
should cause "no compatible bridge window" errors when we enumerate
devices using that I/O space.

The mmio and mmio_pref casts are not strictly necessary, but without
them, correctness depends on the types of the PCI_MEMORY_RANGE_MASK and
PCI_PREF_RANGE_MASK constants, which are not obvious from reading the
local code.

Found by Coverity (CID 138747 and CID 138748).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

pci_enable_obff() and pci_enable_ltr() incorrectly check "dev->bus" instead
of "dev->bus->self" to determine whether the upstream device is a P2P
bridge or a host bridge.  For devices on the root bus, the upstream device
is a host bridge, "dev->bus != NULL" and "dev->bus->self == NULL", and we
panic with a null pointer dereference.

These functions should previously have panicked when called on devices
supporting OBFF or LTR, so they should be regarded as untested.

Found by Coverity (CID 143038 and CID 143039).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Use "__weak" instead of the gcc-specific "__attribute__ ((weak))"
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Warning(drivers/pci/setup-bus.c:277): No description found for parameter 'fail_head'
Warning(drivers/pci/setup-bus.c:277): Excess function parameter 'failed_list' description in 'assign_requested_resources_sorted'
Signed-off-by: Wanpeng Li <liwp.linux@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/jan-intx-masking:
  PCI: add Ralink RT2800 broken INTx masking quirk
  PCI: add Chelsio T310 10GbE NIC broken INTx masking quirk
  PCI: add infrastructure for devices with broken INTx masking

* topic/sebastian-devinit-fixups:
  scripts/modpost: check for bad references in .pci.fixups area
  sh/PCI: move fixup hooks from __init to __devinit
  powerpc/PCI: move fixup hooks from __init to __devinit
  frv/PCI: move fixup hooks from __init to __devinit
  arm/PCI: move fixup hooks from __init to __devinit
  alpha/PCI: move fixup hooks from __init to __devinit
  PCI: move fixup hooks from __init to __devinit
  x86/PCI: move fixup hooks from __init to __devinit

* topic/stowe-cap-cleanup:
  PCI: remove redundant capabilities checking in pci_{save, restore}_pcie_state
  PCI: add pci_pcie_cap2() check for PCIe feature capabilities >= v2
  PCI: remove redundant checking in PCI Express capability routines
  PCI: make pci_ltr_supported() static

Passes pci_intx_mask_supported test but continues to send interrupts
as discovered through VFIO-based device assignment.

http://www.spinics.net/lists/kvm/msg73738.html

[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

According to

http://thread.gmane.org/gmane.comp.emulators.kvm.devel/91388

the T310 does not properly support INTx masking as it fails to keep the
PCI_STATUS_INTERRUPT bit updated once the interrupt is masked. Mark this
adapter as broken so that pci_intx_mask_supported won't report it as
compatible.

[bhelgaas: use HEADER, not FINAL, which is currently broken for hotplug]
Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

pci_intx_mask_supported() assumes INTx masking is supported if the
PCI_COMMAND_INTX_DISABLE bit is writable.  But when that bit is set,
some devices don't actually mask INTx or update PCI_STATUS_INTERRUPT
as we expect.

This patch adds a way for quirks to identify these broken devices.

[bhelgaas: split out from Chelsio quirk addition]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Functions used for PCI fixups (like DECLARE_PCI_FIXUP_HEADER) are often
marked __init. This is okay as long as nobody is using PCI hotplug.
However if one does execute
| echo 1 > /sys/bus/pci/rescan

and we hit a module which is marked __init istead of __devinit then we
go boom because the code is removed after the kernel booted. This patch
help to see those section mismatches.

Cc: Michal Marek <mmarek@suse.cz>
Cc: linux-kbuild@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.

However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.

Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

The fixups are executed once the pci-device is found which is during
boot process so __init seems fine as long as the platform does not
support hotplug.

However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.

Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

pcibios_assign_resource() isn't used anywhere; remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

* topic/alex-vfio-prep:
  PCI: misc pci_reg additions
  PCI: create common pcibios_err_to_errno
  PCI: export pci_user functions for use by other drivers
  PCI: add ACS validation utility
  PCI: add PCI DMA source ID quirk