The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream

These hubs suffer from two separate problems:

1) After the host system was suspended and woken up, the hubs appear to
   be in a random state. Some downstream ports (both internal to the
   built-in audio and network controllers, and external to USB sockets)
   may no longer be functional. The exact list of disabled ports (if
   any) changes from wakeup to wakeup. Ports remain in that state until
   the dock is power-cycled, or until the laptop is rebooted.

   Wakeup sources connected to the hubs (keyboard, WoL on the integrated
   gigabit controller) will wake the system up from suspend, but they
   may no longer work after wakeup (and in that case will no longer work
   as wakeup source in a subsequent suspend-wakeup cycle).

   This issue appears in the logs with messages such as:

     usb 1-6.1-port4: cannot disable (err = -71)
     usb 1-6-port2: cannot disable (err = -71)
     usb 1-6.1: clear tt 1 (80c0) error -71
     usb 1-6-port4: cannot disable (err = -71)
     usb 1-6.4: PM: dpm_run_callback(): usb_dev_resume+0x0/0x10 [usbcore] returns -71
     usb 1-6.4: PM: failed to resume async: error -71
     usb 1-7: reset full-speed USB device number 5 using xhci_hcd
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
     usb 1-6.1-port1: cannot disable (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: cannot reset (err = -71)
     usb 1-6.1-port1: Cannot enable. Maybe the USB cable is bad?
     usb 1-6.1-port1: cannot disable (err = -71)

2) Some USB devices cannot be enumerated properly. So far I have only
   seen the issue with USB 3.0 devices. The same devices work without
   problem directly connected to the host system, to other systems or to
   other hubs (even when those hubs are connected to the OneLink+ dock).

   One very reliable reproducer is this USB 3.0 HDD enclosure:
   152d:9561 JMicron Technology Corp. / JMicron USA Technology Corp. Mobius

   I have seen it happen sporadically with other USB 3.0 enclosures,
   with controllers from different manufacturers, all self-powered.

   Typical messages in the logs:

     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 6, error -62
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 7, error -62
     usb 2-1-port4: attempt power cycle
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 8, error -62
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
     usb 2-1.4: device not accepting address 9, error -62
     usb 2-1-port4: unable to enumerate USB device

Through trial and error, I found that the USB_QUIRK_RESET_RESUME solved
the second issue. Further testing then uncovered the first issue. Test
results are summarized in this table:

=======================================================================================
Settings                        USB2 hotplug    USB3 hotplug    State after waking up
---------------------------------------------------------------------------------------

power/control=auto              works           fails           broken

usbcore.autosuspend=-1          works           works           broken
OR power/control=on

power/control=auto              works (1)       works (1)       works
and USB_QUIRK_RESET_RESUME

power/control=on                works           works           works
and USB_QUIRK_RESET_RESUME

HUB_QUIRK_DISABLE_AUTOSUSPEND   works           works           works
and USB_QUIRK_RESET_RESUME

=======================================================================================

In those results, the power/control settings are applied to both hubs,
both on the USB2 and USB3 side, before each test.

From those results, USB_QUIRK_RESET_RESUME is required to reset the hubs
properly after a suspend-wakeup cycle, and the hubs must not autosuspend
to work around the USB3 issue.

A secondary effect of USB_QUIRK_RESET_RESUME is to prevent the hubs'
upstream links from suspending (the downstream ports can still suspend).
This secondary effect is used in results (1). It is enough to solve the
USB3 problem.

Setting USB_QUIRK_RESET_RESUME on those hubs is the smallest patch that
solves both issues.

Prior to creating this patch, I have used the USB_QUIRK_RESET_RESUME via
the kernel command line for over a year without noticing any side
effect.

Thanks to Oliver Neukum @Suse for explanations of the operations of
USB_QUIRK_RESET_RESUME, and requesting more testing.
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220927073407.5672-1-jflf_kernel@gmx.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next

Mika writes:
  "thunderbolt: Changes for v6.1 merge window

   This includes following Thunderbolt/USB4 changes for the v6.1 merge
   window:
     - Support for Intel Meteor Lake integrated Thunderbolt/USB4 controller
     - Support for ASMedia USB4 controller NVM firmware upgrade
     - Receiver lane margining support
     - Few fixes and cleanups.

   All these have been in linux-next with no reported issues."

* tag 'thunderbolt-for-v6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
  thunderbolt: Explicitly enable lane adapter hotplug events at startup
  thunderbolt: Use dev_err_probe()
  thunderbolt: Convert to use sysfs_emit()/sysfs_emit_at() APIs
  thunderbolt: Fix spelling mistake "simultaneusly" -> "simultaneously"
  thunderbolt: debugfs: Fix spelling mistakes in seq_puts text
  thunderbolt: Add support for ASMedia NVM image format
  thunderbolt: Move vendor specific NVM handling into nvm.c
  thunderbolt: Provide tb_retimer_nvm_read() analogous to tb_switch_nvm_read()
  thunderbolt: Rename and make nvm_read() available for other files
  thunderbolt: Extend NVM version fields to 32-bits
  thunderbolt: Allow NVM upgrade of USB4 host routers
  thunderbolt: Add support for receiver lane margining
  thunderbolt: Add helper to check if CL states are enabled on port
  thunderbolt: Pass CL state bitmask to tb_port_clx_supported()
  thunderbolt: Move port CL state functions into correct place in switch.c
  thunderbolt: Move tb_xdomain_parent() to tb.h
  thunderbolt: Add support for Intel Meteor Lake
  thunderbolt: Add comment where Thunderbolt 4 PCI IDs start
  thunderbolt: Add DP OUT resource when DP tunnel is discovered

Thinh Nguyen has agreed to become the new dwc3 maintainer seeing that
I haven't had time to dedicate to the mailing list.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20220929074844.351938-1-balbi@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.

Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.

Note that this is found by KMSAN, so only kernel compilation
is tested.

Reported-by: syzbot+79832d33eb89fb3cd092@syzkaller.appspotmail.com
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220922134847.1101921-1-dzm91@hust.edu.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922133323.2135494-2-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922133323.2135494-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use DEFINE_SHOW_ATTRIBUTE helper macro to simplify the code.
No functional change.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922142505.3248167-1-liushixin2@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Smatch reports the following error:

drivers/usb/cdns3/cdns3-plat.c:113 cdns3_plat_probe() warn:
platform_get_irq() does not return zero

From the document, platform_get_irq_byname_optional only returns
non-zero value, and negative value on failure.

Fix this by removing the zero value checking.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20220926135922.24541-1-dzm91@hust.edu.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use skb_put_data() instead of skb_put() and memcpy(), which is clear.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220927024344.14352-1-shangxiaojing@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-6-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-5-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-4-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-3-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220927072616.913672-2-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220922134806.2204579-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135708.2212249-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220922135228.2206755-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220922123951.2004328-1-yangyingliang@huawei.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Software that has run before the USB4 CM in Linux runs may have disabled
hotplug events for a given lane adapter.

Other CMs such as that one distributed with Windows 11 will enable hotplug
events. Do the same thing in the Linux CM which fixes hotplug events on
"AMD Pink Sardine".

Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Use the usb_endpoint_maxp() helper instead of open coding.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220822151456.27178-4-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up URB initialisation somewhat by introducing a temporary variable
and separating declaration and non-trivial initialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220822151456.27178-3-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a temporary variable to make the endpoint sanity checks a bit more
readable.

While at it, fix a typo in the usb_set_interface() comment.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220822151456.27178-2-johan@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here for other follow-on changes to be able to
be applied successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull ext4 fixes from Ted Ts'o:
 "Regression and bug fixes:

   - Performance regression fix from 5.18 on a Rasberry Pi

   - Fix extent parsing bug which triggers a BUG_ON when a (corrupted)
     extent tree has has a non-root node when zero entries.

   - Fix a livelock where in the right (wrong) circumstances a large
     number of nfsd threads can try to write to a nearly full file
     system, and retry for hours(!)"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: limit the number of retries after discarding preallocations blocks
  ext4: fix bug in extents parsing when eh_entries == 0 and eh_depth > 0
  ext4: use buckets for cr 1 block scan instead of rbtree
  ext4: use locality group preallocation for small closed files
  ext4: make directory inode spreading reflect flexbg size
  ext4: avoid unnecessary spreading of allocations among groups
  ext4: make mballoc try target group first even with mb_optimize_scan

Merge tag 'dax-and-nvdimm-fixes-v6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm

Pull NVDIMM and DAX fixes from Dan Williams:
 "A recently discovered one-line fix for devdax that further addresses a
  v5.5 regression, and (a bit embarrassing) a small batch of fixes that
  have been sitting in my fixes tree for weeks.

  The older fixes have soaked in linux-next during that time and address
  an fsdax infinite loop and some other minor fixups.

   - Fix a infinite loop bug in fsdax

   - Fix memory-type detection for devdax (EINJ regression)

   - Small cleanups"

* tag 'dax-and-nvdimm-fixes-v6.0-final' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  devdax: Fix soft-reservation memory description
  fsdax: Fix infinite loop in dax_iomap_rw()
  nvdimm/namespace: drop nested variable in create_namespace_pmem()
  ndtest: Cleanup all of blk namespace specific code
  pmem: fix a name collision

Pull i2c fixes from Wolfram Sang:
 "I2C driver bugfixes for mlxbf and imx, a few documentation fixes after
  the rework this cycle, and one hardening for the i2c-mux core"

* tag 'i2c-for-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mux: harden i2c_mux_alloc() against integer overflows
  i2c: mlxbf: Fix frequency calculation
  i2c: mlxbf: prevent stack overflow in mlxbf_i2c_smbus_start_transaction()
  i2c: mlxbf: incorrect base address passed during io write
  Documentation: i2c: fix references to other documents
  MAINTAINERS: remove Nehal Shah from AMD MP2 I2C DRIVER
  i2c: imx: If pm_runtime_get_sync() returned 1 device access is possible

Pick up another "Soft Reservation" fix for v6.0-final on top of some
straggling nvdimm fixes that missed v5.19.

The "hmem" platform-devices that are created to represent the
platform-advertised "Soft Reserved" memory ranges end up inserting a
resource that causes the iomem_resource tree to look like this:

340000000-43fffffff : hmem.0
  340000000-43fffffff : Soft Reserved
    340000000-43fffffff : dax0.0

This is because insert_resource() reparents ranges when they completely
intersect an existing range.

This matters because code that uses region_intersects() to scan for a
given IORES_DESC will only check that top-level 'hmem.0' resource and
not the 'Soft Reserved' descendant.

So, to support EINJ (via einj_error_inject()) to inject errors into
memory hosted by a dax-device, be sure to describe the memory as
IORES_DESC_SOFT_RESERVED. This is a follow-on to:

commit b13a3e5f ("ACPI: APEI: Fix _EINJ vs EFI_MEMORY_SP")

...that fixed EINJ support for "Soft Reserved" ranges in the first
instance.

Fixes: 262b45ae ("x86/efi: EFI soft reservation to E820 enumeration")
Reported-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Tested-by: Ricardo Sandoval Torres <ricardo.sandoval.torres@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Omar Avelar <omar.avelar@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mark Gross <markgross@kernel.org>
Link: https://lore.kernel.org/r/166397075670.389916.7435722208896316387.stgit@dwillia2-xfh.jf.intel.comSigned-off-by: Dan Williams <dan.j.williams@intel.com>

Merge tag 'kbuild-fixes-v6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix build error for the combination of SYSTEM_TRUSTED_KEYRING=y and
   X509_CERTIFICATE_PARSER=m

 - Fix DEBUG_INFO_SPLIT to generate debug info for GCC 11+ and Clang 12+

 - Revive debug info for assembly files

 - Remove unused code

* tag 'kbuild-fixes-v6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  Makefile.debug: re-enable debug info for .S files
  Makefile.debug: set -g unconditional on CONFIG_DEBUG_INFO_SPLIT
  certs: make system keyring depend on built-in x509 parser
  Kconfig: remove unused function 'menu_get_root_menu'
  scripts/clang-tools: remove unused module

Pull s390 fix from Vasily Gorbik:

 - Fix potential hangs in VFIO AP driver

* tag 's390-6.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/vfio-ap: bypass unnecessary processing of AP resources

Pull power management fixes from Rafael Wysocki:
 "These fix an uninitialized variable usage in the operating performance
  points code and add missing DT bindings for it.

  Specifics:

   - Fix uninitialized variable usage in dev_pm_opp_config_clks_simple()
     (Christophe JAILLET)

   - Add missing OPP DT properties (Rob Herring)"

* tag 'pm-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  dt-bindings: opp: Add missing (unevaluated|additional)Properties on child nodes
  OPP: Fix an un-initialized variable usage

Pull char/misc driver fixes from Greg KH:
 "Here are three tiny driver fixes for 6.0-rc7.  They include:

   - phy driver reset bugfix

   - fpga memleak bugfix

   - counter irq config bugfix

  The first two have been in linux-next for a while, the last one has
  only been added to my tree in the past few days, but was in linux-next
  under a different commit id. I couldn't pull directly from the counter
  tree due to some gpg key propagation issue, so I took the commit
  directly from email instead"

* tag 'char-misc-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  counter: 104-quad-8: Fix skipped IRQ lines during events configuration
  fpga: m10bmc-sec: Fix possible memory leak of flash_buf
  phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support

Pull tty/serial driver fixes from Greg KH:
 "Here are some small, and late, serial driver fixes for 6.0-rc7 to
  resolve some reported problems.

  Included in here are:

   - tegra icount accounting fixes, including a framework function that
     other drivers will be converted over to using in 6.1-rc1.

   - fsl_lpuart reset bugfix

   - 8250 omap 485 bugfix

   - sifive serial clock bugfix

  The last three patches have not shown up in linux-next due to them
  being added to my tree only 2 days ago, but they are tiny and
  self-contained and the developers say they resolve issues that they
  have with 6.0-rc. The other three have been in linux-next for a while
  with no reported issues"

* tag 'tty-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: sifive: enable clocks for UART when probed
  serial: 8250: omap: Use serial8250_em485_supported
  serial: fsl_lpuart: Reset prior to registration
  serial: tegra-tcu: Use uart_xmit_advance(), fixes icount.tx accounting
  serial: tegra: Use uart_xmit_advance(), fixes icount.tx accounting
  serial: Create uart_xmit_advance()

Pull cgroup fixes from Tejun Heo:

 - Add Waiman Long as a cpuset maintainer

 - cgroup_get_from_id() could be fed a kernfs ID which doesn't point to
   a cgroup directory but a knob file and then crash. Error out if the
   lookup kernfs_node isn't a directory.

* tag 'cgroup-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: cgroup_get_from_id() must check the looked-up kn is a directory
  cpuset: Add Waiman Long as a cpuset maintainer

Pull workqueue fix from Tejun Heo:
 "Just one patch to improve flush lockdep coverage"

* tag 'wq-for-6.0-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: don't skip lockdep work dependency in cancel_work_sync()

Pull io_uring fix from Jens Axboe:
 "Just a single fix for an issue with un-reaped IOPOLL requests on ring
  exit"

* tag 'io_uring-6.0-2022-09-23' of git://git.kernel.dk/linux:
  io_uring: ensure that cached task references are always put on exit

Pull block fixes from Jens Axboe:
 "Fix a regression that's been plaguing us by reverting the offending
  commit, as attempts to both reproduce the issue and fix it in a saner
  fashion have failed.

  Fix for a potential oops condition in the s390 dasd block driver"

* tag 'block-6.0-2022-09-22' of git://git.kernel.dk/linux:
  Revert "block: freeze the queue earlier in del_gendisk"
  s390/dasd: fix Oops in dasd_alias_get_start_dev due to missing pavgroup

Unify error message format by using dev_err_probe().
While at it, use temporary variable for device in
the rest of the messaging calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the value
to be returned to user space.

While at it, use Elvis operator in some cases.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>