snprintf returns the actual length of the buffer created; however,
this is not the case if snprintf truncates its parameter.
See https://lwn.net/Articles/69419/ for a detailed explanation.
The current code correctly handles this case at the expense
of extra code in the return statement.

scnprintf does returns the actual length of the buffer created
making the ?: operator unnecessary in the return
statement.

This change does not alter the functionality of the code.
Signed-off-by: Daniel M German <dmg@turingmachine.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

On spin lock release in rx_submit, gether_disconnect get a chance to
run, it makes port_usb NULL, rx_submit access NULL port USB, hence null
pointer crash.

Fixed by releasing the lock in rx_submit after port_usb is used.

Fixes: 2b3d942c ("usb ethernet gadget: split out network core")
Cc: <stable@vger.kernel.org>
Signed-off-by: Kiruthika Varadarajan <Kiruthika.Varadarajan@harman.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This change is to fix below warning message in following scenario:
usb_composite_setup_continue: Unexpected call

When system tried to enter suspend, the fsg_disable() will be called to
disable fsg driver and send a signal to fsg_main_thread. However, at
this point, the fsg_main_thread has already been frozen and can not
respond to this signal. So, this signal will be pended until
fsg_main_thread wakes up.

Once system resumes from suspend, fsg_main_thread will detect a signal
pended and do some corresponding action (in handle_exception()). Then,
host will send some setup requests (get descriptor, set configuration...)
to UDC driver trying to enumerate this device. During the handling of "set
configuration" request, it will try to sync up with fsg_main_thread by
sending a signal (which is the same as the signal sent by fsg_disable)
to it. In a similar manner, once the fsg_main_thread receives this
signal, it will call handle_exception() to handle the request.

However, if the fsg_main_thread wakes up from suspend a little late and
"set configuration" request from Host arrives a little earlier,
fsg_main_thread might come across the request from "set configuration"
when it handles the signal from fsg_disable(). In this case, it will
handle this request as well. So, when fsg_main_thread tries to handle
the signal sent from "set configuration" later, there will nothing left
to do and warning message "Unexpected call" is printed.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: EJ Hsu <ejh@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Gadget applications may have a requirement to disable the U1 and U2
entry based on the usecase. Below are few usecases where the disabling
U1/U2 entries may be possible.

Usecase 1:
When combining dwc3 with an redriver for a USB Type-C device solution, it
sometimes have problems with leaving U1/U2 for certain hosts, resulting in
link training errors and reconnects. For this U1/U2 state entries may be
avoided.

Usecase 2:
When performing performance benchmarking on mass storage gadget the
U1 and U2 entries can be disabled.

Usecase 3:
When periodic transfers like ISOC transfers are used with bInterval
of 1 which doesn't require the link to enter into U1 or U2 state entry
(since ping is issued from host for every uframe interval). In this
case the U1 and U2 entry can be disabled.

Disablement of U1/U2 can be done by setting U1DevExitLat and U2DevExitLat
values to 0 in the BOS descriptor. Host on seeing 0 value for U1DevExitLat
and U2DevExitLat, it doesn't send SET_SEL requests to the gadget. There
may be some hosts which may send SET_SEL requests even after seeing 0 in
the UxDevExitLat of BOS descriptor. To aviod U1/U2 entries for these type
of hosts, dwc3 controller can be programmed to reject those U1/U2 requests
by not enabling ACCEPTUxENA bits in DCTL register.

This patch updates the same.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Claus H. Stovgaard <cst@phaseone.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Passing struct usb_gadget * as an extra argument in get_config_params
makes gadget drivers to easily update the U1DevExitLat & U2DevExitLat
values based on the values passed from the device tree. This patch
does the same
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch updates the documentation with the information related
to the quirks that needs to be added for disabling the link entering
into the U1 and U2 states
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use of_clk_get_parent_count() instead of open coding.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The required clocks needs to be enabled before the first register
access. After commit fe8abf33 ("usb: dwc3: support clocks and resets
for DWC3 core"), this happens when the dwc3_core_is_valid function is
called, but the mentioned commit adds that call in the wrong place,
before the clocks are enabled. So, move that call after the
clk_bulk_enable() to ensure the clocks are enabled and the reset
deasserted.

I detected this while, as experiment, I tried to move the clocks and resets
from the glue layer to the DWC3 core on a Samsung Chromebook Plus.

That was not detected before because, in most cases, the glue layer
initializes SoC-specific things and then populates the child "snps,dwc3"
with those clocks already enabled.

Fixes: b873e2d0 ("usb: dwc3: Do core validation early on probe")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

dwc3_qcom_clk_init() is called with of_count_phandle_with_args() as an
argument.  If of_count_phandle_with_args() returns an error, the number
of clocks will be a negative value and will lead to undefined behaviour.

Ensure we check for an error before attempting to blindly use the value.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When booting with Device Tree, the current default boot configuration
table option, the request to boot via 'host mode' comes from the
'dr_mode' property.  A property of the same name can be used inside
ACPI tables too.  However it is missing from the SDM845's ACPI tables
so we have to supply this information using Platform Device Properties
instead.

This does not change the behaviour of any currently supported devices.
The property is only set on ACPI enabled platforms, thus for H/W
booting DT, unless a 'dr_mode' property is present, the default is
still OTG (On-The-Go) as per [0].  Any new ACPI devices added will
also be able to over-ride this implementation by providing a 'dr_mode'
property in their ACPI tables.  In cases where 'dr_mode' is omitted
from the tables AND 'host mode' should not be the default (very
unlikely), then we will have to add some way of choosing between them
at run time - most likely by ACPI HID.

[0] Documentation/devicetree/bindings/usb/generic.txt
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In Linux, the DWC3 core exists as its own independent platform device.
Thus when describing relationships in Device Tree, the current default
boot configuration table option, the DWC3 core often resides as a child
of the platform specific node.  Both of which are given their own
address space descriptions and the drivers can be mostly agnostic to
each other.

However, other Operating Systems have taken a more monolithic approach,
which is evident in the configuration ACPI tables for the Qualcomm
Snapdragon SDM850, where all DWC3 (core and platform) components are
described under a single IO memory region.

To ensure successful booting using the supplied ACPI tables, we need to
devise a way to chop up the address regions provided and subsequently
register the DWC3 core with the resultant information, which is
precisely what this patch aims to achieve.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

When booting with ACPI as the active set of configuration tables,
all; clocks, regulators, pin functions ect are expected to be at
their ideal values/levels/rates, thus the associated frameworks
are unavailable.  Ensure calls to these APIs are shielded when
ACPI is enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This reverts commit b0d65902.

The reverted commit does nothing but adding two unnecessary lines
of code.  It sets a local variable to NULL in two functions, but
that variable is not used anywhere in the rest of those functions.
This is just confusing, so let's remove it.

Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromiun.org>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The pointer 's' is being assigned however the pointer is
never used with either of these values before it it reassigned much
later on.  I suspect it was going to be used in the output of the
main control registers scnprintf but was omitted.  The assignments
of 's' to the driver name or the literal string are redundant and
can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

In some cases the "Allocate & copy" block in ffs_epfile_io() is not
executed. Consequently, in such a case ffs_alloc_buffer() is never called
and struct ffs_io_data is not initialized properly. This in turn leads to
problems when ffs_free_buffer() is called at the end of ffs_epfile_io().

This patch uses kzalloc() instead of kmalloc() in the aio case and memset()
in non-aio case to properly initialize struct ffs_io_data.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

With the current implementation omap_udc_stop is always
returning -ENODEV.

Added changes to return 0 and remove variable status.

Issue identified with coccicheck
drivers/usb/gadget/udc/omap_udc.c:2106:6-12:
Unneeded variable: "status". Return "- ENODEV" on line 2128
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes below warning reported by coccicheck

drivers/usb/gadget/udc/fotg210-udc.c:484:5-8: Unneeded variable: "ret".
Return "0" on line 507
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

at91_wakeup is always returning -EINVAL.

But usb_gadget_wakeup expects 0 on success and negative number on
failure. As per current implementation this function wont fail.

This patch removes unneeded variable and returns 0.

Issue identified by coccicheck

drivers/usb/gadget/udc/at91_udc.c:802:6-12:
Unneeded variable: "status". Return "- EINVAL" on line 821
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The RZ/G2E cat874 board has a type-c connector connected to hd3ss3220 usb
type-c drp port controller. Enhance role switch support to assign the role
requested by connector device using the usb role switch class framework.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Fixed a coding style issue, replacing unsigned with unsigned int.
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Jonas Stenvall <jonas.stenvall.umea@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The following line of code in function ffs_epfile_io is trying to set
flag io_data->use_sg in case buffer required is larger than one page.

    io_data->use_sg = gadget->sg_supported && data_len > PAGE_SIZE;

However at this point of time the variable data_len has not been set
to the proper buffer size yet. The consequence is that io_data->use_sg
is always set regardless what buffer size really is, because the condition
(data_len > PAGE_SIZE) is effectively an unsigned comparison between
-EINVAL and PAGE_SIZE which would always result in TRUE.

Fixes: 772a7a72 ("usb: gadget: f_fs: Allow scatter-gather buffers")
Signed-off-by: Fei Yang <fei.yang@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If the 'snps,need-phy-for-wake' is set in the device tree then:

- We know that we can wakeup, so call device_set_wakeup_capable().
  The USB core will use this knowledge to enable wakeup by default.
- We know that we should keep the PHY on during suspend if something
  on our root hub needs remote wakeup.  This requires the patch (USB:
  Export usb_wakeup_enabled_descendants()).  Note that we don't keep
  the PHY on at suspend time if it's not needed because it would be a
  power draw.

If we later find some users of dwc2 that can support wakeup without
keeping the PHY on we may want to add a way to call
device_set_wakeup_capable() without keeping the PHY on at suspend
time.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We want to be able to wake from USB if a device is plugged in that
wants remote wakeup.  Enable it on both dwc2 controllers.

NOTE: this is added specifically to veyron and not to rk3288 in
general since it's not known whether all rk3288 boards are designed to
support USB wakeup.  It is plausible that some boards could shut down
important rails in S3.

Also note that currently wakeup doesn't seem to happen unless you use
the "deep" suspend mode (where SDRAM is turned off).  Presumably the
shallow suspend mode is gating some sort of clock that's important but
I couldn't easily figure out how to get it working.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Some SoCs with a dwc2 USB controller may need to keep the PHY on to
support remote wakeup.  Allow specifying this as a device tree
property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Samsung Exynos SoCs require to force UTMI width to 8bit, otherwise the
host side of the shared USB2 PHY doesn't work.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 707d80f0 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add support for the OTG ID change interrupt to switch between Host
and Device mode.

Tested on the Hardkernel Odroid-N2 board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For consistency with the naming of (most) other documentation files for DT
bindings for Renesas IP blocks rename the Renesas USB3.0 peripheral
documentation file from renesas-gen3.txt to renesas,gen3.txt.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

For consistency with the naming of (most) other documentation files for DT
bindings for Renesas IP blocks rename the Renesas USBHS documentation file
from renesas-usbhs.txt to renesas,usbhs.txt.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull x86 fixes from Thomas Gleixner:
 "The accumulated fixes from this and last week:

   - Fix vmalloc TLB flush and map range calculations which lead to
     stale TLBs, spurious faults and other hard to diagnose issues.

   - Use fault_in_pages_writable() for prefaulting the user stack in the
     FPU code as it's less fragile than the current solution

   - Use the PF_KTHREAD flag when checking for a kernel thread instead
     of current->mm as the latter can give the wrong answer due to
     use_mm()

   - Compute the vmemmap size correctly for KASLR and 5-Level paging.
     Otherwise this can end up with a way too small vmemmap area.

   - Make KASAN and 5-level paging work again by making sure that all
     invalid bits are masked out when computing the P4D offset. This
     worked before but got broken recently when the LDT remap area was
     moved.

   - Prevent a NULL pointer dereference in the resource control code
     which can be triggered with certain mount options when the
     requested resource is not available.

   - Enforce ordering of microcode loading vs. perf initialization on
     secondary CPUs. Otherwise perf tries to access a non-existing MSR
     as the boot CPU marked it as available.

   - Don't stop the resource control group walk early otherwise the
     control bitmaps are not updated correctly and become inconsistent.

   - Unbreak kgdb by returning 0 on success from
     kgdb_arch_set_breakpoint() instead of an error code.

   - Add more Icelake CPU model defines so depending changes can be
     queued in other trees"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
  x86/kasan: Fix boot with 5-level paging and KASAN
  x86/fpu: Don't use current->mm to check for a kthread
  x86/kgdb: Return 0 from kgdb_arch_set_breakpoint()
  x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled
  x86/resctrl: Don't stop walking closids when a locksetup group is found
  x86/fpu: Update kernel's FPU state before using for the fsave header
  x86/mm/KASLR: Compute the size of the vmemmap section properly
  x86/fpu: Use fault_in_pages_writeable() for pre-faulting
  x86/CPU: Add more Icelake model numbers
  mm/vmalloc: Avoid rare case of flushing TLB with weird arguments
  mm/vmalloc: Fix calculation of direct map addr range

Pull timer fixes from Thomas Gleixner:
 "A set of small fixes:

   - Repair the ktime_get_coarse() functions so they actually deliver
     what they are supposed to: tick granular time stamps. The current
     code missed to add the accumulated nanoseconds part of the
     timekeeper so the resulting granularity was 1 second.

   - Prevent the tracer from infinitely recursing into time getter
     functions in the arm architectured timer by marking these functions
     notrace

   - Fix a trivial compiler warning caused by wrong qualifier ordering"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Repair ktime_get_coarse*() granularity
  clocksource/drivers/arm_arch_timer: Don't trace count reader functions
  clocksource/drivers/timer-ti-dm: Change to new style declaration

Pull RAS fixes from Thomas Gleixner:
 "Two small fixes for RAS:

   - Use a proper search algorithm to find the correct element in the
     CEC array. The replacement was a better choice than fixing the
     crash causes by the original search function with horrible duct
     tape.

   - Move the timer based decay function into thread context so it can
     actually acquire the mutex which protects the CEC array to prevent
     corruption"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  RAS/CEC: Convert the timer callback to a workqueue
  RAS/CEC: Fix binary search function

Pull x86 platform driver fixes from Andy Shevchenko:

 - fix a couple of Mellanox driver enumeration issues

 - fix ASUS laptop regression with backlight

 - fix Dell computers that got a wrong mode (tablet versus laptop) after
   resume

* tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow
  platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration
  platform/x86: intel-vbtn: Report switch events when event wakes device
  platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi

Pull USB fixes from Greg KH:
 "Here are some small USB driver fixes for 5.2-rc5

  Nothing major, just some small gadget fixes, usb-serial new device
  ids, a few new quirks, and some small fixes for some regressions that
  have been found after the big 5.2-rc1 merge.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: typec: Make sure an alt mode exist before getting its partner
  usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe()
  usb: gadget: dwc2: fix zlp handling
  usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA
  usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC
  usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i]
  usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()
  usb: dwc2: Fix DMA cache alignment issues
  usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression)
  USB: Fix chipmunk-like voice when using Logitech C270 for recording audio.
  USB: usb-storage: Add new ID to ums-realtek
  usb: typec: ucsi: ccg: fix memory leak in do_flash
  USB: serial: option: add Telit 0x1260 and 0x1261 compositions
  USB: serial: pl2303: add Allied Telesis VT-Kit3
  USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode

Pull powerpc fixes from Michael Ellerman:
 "One fix for a regression introduced by our 32-bit KASAN support, which
  broke booting on machines with "bootx" early debugging enabled.

  A fix for a bug which broke kexec on 32-bit, introduced by changes to
  the 32-bit STRICT_KERNEL_RWX support in v5.1.

  Finally two fixes going to stable for our THP split/collapse handling,
  discovered by Nick. The first fixes random crashes and/or corruption
  in guests under sufficient load.

  Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
  Malaterre"

* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
  powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
  powerpc/64s: Fix THP PMD collapse serialisation
  powerpc: Fix kexec failure on book3s/32

Pull tracing fixes from Steven Rostedt:

 - Out of range read of stack trace output

 - Fix for NULL pointer dereference in trace_uprobe_create()

 - Fix to a livepatching / ftrace permission race in the module code

 - Fix for NULL pointer dereference in free_ftrace_func_mapper()

 - A couple of build warning clean ups

* tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
  module: Fix livepatch/ftrace module text permissions race
  tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
  tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
  tracing: Make two symbols static
  tracing: avoid build warning with HAVE_NOP_MCOUNT
  tracing: Fix out-of-range read in trace_stack_print()

Adric Blake reported the following warning during suspend-resume:

  Enabling non-boot CPUs ...
  x86: Booting SMP configuration:
  smpboot: Booting Node 0 Processor 1 APIC 0x2
  unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \
   at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20)
  Call Trace:
   intel_set_tfa
   intel_pmu_cpu_starting
   ? x86_pmu_dead_cpu
   x86_pmu_starting_cpu
   cpuhp_invoke_callback
   ? _raw_spin_lock_irqsave
   notify_cpu_starting
   start_secondary
   secondary_startup_64
  microcode: sig=0x806ea, pf=0x80, revision=0x96
  microcode: updated to revision 0xb4, date = 2019-04-01
  CPU1 is up

The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated
by microcode. The log above shows that the microcode loader callback
happens after the PMU restoration, leading to the conjecture that
because the microcode hasn't been updated yet, that MSR is not present
yet, leading to the #GP.

Add a microcode loader-specific hotplug vector which comes before
the PERF vectors and thus executes earlier and makes sure the MSR is
present.

Fixes: 400816f6 ("perf/x86/intel: Implement support for TSX Force Abort")
Reported-by: Adric Blake <promarbler14@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: x86@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637

Pull cgroup fixes from Tejun Heo:
 "This has an unusually high density of tricky fixes:

   - task_get_css() could deadlock when it races against a dying cgroup.

   - cgroup.procs didn't list thread group leaders with live threads.

     This could mislead readers to think that a cgroup is empty when
     it's not. Fixed by making PROCS iterator include dead tasks. I made
     a couple mistakes making this change and this pull request contains
     a couple follow-up patches.

   - When cpusets run out of online cpus, it updates cpusmasks of member
     tasks in bizarre ways. Joel improved the behavior significantly"

* 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: restore sanity to cpuset_cpus_allowed_fallback()
  cgroup: Fix css_task_iter_advance_css_set() cset skip condition
  cgroup: css_task_iter_skip()'d iterators must be advanced before accessed
  cgroup: Include dying leaders with live threads in PROCS iterations
  cgroup: Implement css_task_iter_skip()
  cgroup: Call cgroup_release() before __exit_signal()
  docs cgroups: add another example size for hugetlb
  cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()

Pull drm fixes from Daniel Vetter:
 "Nothing unsettling here, also not aware of anything serious still
  pending.

  The edid override regression fix took a bit longer since this seems to
  be an area with an overabundance of bad options. But the fix we have
  now seems like a good path forward.

  Next week it should be back to Dave.

  Summary:

   - fix regression on amdgpu on SI

   - fix edid override regression

   - driver fixes: amdgpu, i915, mediatek, meson, panfrost

   - fix writecombine for vmap in gem-shmem helper (used by panfrost)

   - add more panel quirks"

* tag 'drm-fixes-2019-06-14' of git://anongit.freedesktop.org/drm/drm: (25 commits)
  drm/amdgpu: return 0 by default in amdgpu_pm_load_smu_firmware
  drm/amdgpu: Fix bounds checking in amdgpu_ras_is_supported()
  drm: add fallback override/firmware EDID modes workaround
  drm/edid: abstract override/firmware EDID retrieval
  drm/i915/perf: fix whitelist on Gen10+
  drm/i915/sdvo: Implement proper HDMI audio support for SDVO
  drm/i915: Fix per-pixel alpha with CCS
  drm/i915/dmc: protect against reading random memory
  drm/i915/dsi: Use a fuzzy check for burst mode clock check
  drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
  drm/panfrost: Require the simple_ondemand governor
  drm/panfrost: make devfreq optional again
  drm/gem_shmem: Use a writecombine mapping for ->vaddr
  drm: panel-orientation-quirks: Add quirk for GPD MicroPC
  drm: panel-orientation-quirks: Add quirk for GPD pocket2
  drm/meson: fix G12A primary plane disabling
  drm/meson: fix primary plane disabling
  drm/meson: fix G12A HDMI PLL settings for 4K60 1000/1001 variations
  drm/mediatek: call mtk_dsi_stop() after mtk_drm_crtc_atomic_disable()
  drm/mediatek: clear num_pipes when unbind driver
  ...