When detecting a spurious EL1 translation fault, we have the CPU retry
the translation using an AT S1E1R instruction, and inspect PAR_EL1 to
determine if the fault was spurious.

When PAR_EL1.F == 0, the AT instruction successfully translated the
address without a fault, which implies the original fault was spurious.
However, in this case we return false and treat the original fault as if
it was not spurious.

Invert the return value so that we treat such a case as spurious.

Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 42f91093 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

The 'F' field of the PAR_EL1 register lives in bit 0, not bit 1.
Fix the broken definition in 'sysreg.h'.

Fixes: e8620cff ("arm64: sysreg: Add some field definitions for PAR_EL1")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>

Preempting from IRQ-return means that the task has its PSTATE saved
on the stack, which will get restored when the task is resumed and does
the actual IRQ return.

However, enabling some CPU features requires modifying the PSTATE. This
means that, if a task was scheduled out during an IRQ-return before all
CPU features are enabled, the task might restore a PSTATE that does not
include the feature enablement changes once scheduled back in.

* Task 1:

PAN == 0 ---|                          |---------------
            |                          |<- return from IRQ, PSTATE.PAN = 0
            | <- IRQ                   |
            +--------+ <- preempt()  +--
                                     ^
                                     |
                                     reschedule Task 1, PSTATE.PAN == 1
* Init:
        --------------------+------------------------
                            ^
                            |
                            enable_cpu_features
                            set PSTATE.PAN on all CPUs

Worse than this, since PSTATE is untouched when task switching is done,
a task missing the new bits in PSTATE might affect another task, if both
do direct calls to schedule() (outside of IRQ/exception contexts).

Fix this by preventing preemption on IRQ-return until features are
enabled on all CPUs.

This way the only PSTATE values that are saved on the stack are from
synchronous exceptions. These are expected to be fatal this early, the
exception is BRK for WARN_ON(), but as this uses do_debug_exception()
which keeps IRQs masked, it shouldn't call schedule().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
[james: Replaced a really cool hack, with an even simpler static key in C.
 expanded commit message with Julien's cover-letter ascii art]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

There is a bug in create_safe_exec_page(), when page table is allocated
it is not checked that table is allocated successfully:

But it is dereferenced in: pgd_none(READ_ONCE(*pgdp)).  Check that
allocation was successful.

Fixes: 82869ac5 ("arm64: kernel: Add support for hibernate/suspend-to-disk")
Reviewed-by: James Morse <james.morse@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Will Deacon <will@kernel.org>

If CONFIG_ARM64_SVE=n then we fail to report ID_AA64ZFR0_EL1 as 0 when
read by userspace, despite being required by the architecture. Although
this is theoretically a change in ABI, userspace will first check for
the presence of SVE via the HWCAP or the ID_AA64PFR0_EL1.SVE field
before probing the ID_AA64ZFR0_EL1 register. Given that these are
reported correctly for this configuration, we can safely tighten up the
current behaviour.

Ensure ID_AA64ZFR0_EL1 is treated as RAZ when CONFIG_ARM64_SVE=n.
Signed-off-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Fixes: 06a916fe ("arm64: Expose SVE2 features for userspace")
Signed-off-by: Will Deacon <will@kernel.org>

We export the entire kernel address space (i.e. the whole of the TTBR1
address range) via /proc/kcore. The kc_vaddr_to_offset() and
kc_offset_to_vaddr() macros are intended to convert between a kernel
virtual address and its offset relative to the start of the TTBR1
address space.

Prior to commit:

  14c127c9 ("arm64: mm: Flip kernel VA space")

... the offset was calculated relative to VA_START, which at the time
was the start of the TTBR1 address space. At this time, PAGE_OFFSET
pointed to the high half of the TTBR1 address space where arm64's
linear map lived.

That commit swapped the position of VA_START and PAGE_OFFSET, but
failed to update kc_vaddr_to_offset() or kc_offset_to_vaddr(), so
since then the two macros behave incorrectly.

Note that VA_START was subsequently renamed to PAGE_END in commit:

  77ad4ce6 ("arm64: memory: rename VA_START to PAGE_END")

As the generic implementations of the two macros calculate the offset
relative to PAGE_OFFSET (which is now the start of the TTBR1 address
space), we can delete the arm64 implementation and use those.

Fixes: 14c127c9 ("arm64: mm: Flip kernel VA space")
Reviewed-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Chris von Recklinghausen <crecklin@redhat.com>
Signed-off-by: Will Deacon <will@kernel.org>

There are no return value checking when using kzalloc() and kcalloc() for
memory allocation. so add it.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>

CONFIG_COMPAT_VDSO is defined by passing '-DCONFIG_COMPAT_VDSO' to the
compiler when the generic compat vDSO code is in use. It's much cleaner
and simpler to expose this as a proper Kconfig option (like x86 does),
so do that and remove the bodge.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

For consistency with CROSS_COMPILE_COMPAT, mechanically rename COMPATCC
to CC_COMPAT so that specifying aspects of the compat vDSO toolchain in
the environment isn't needlessly confusing.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Directly passing the '--target' option to clang by appending to
COMPATCC does not work if COMPATCC has been specified explicitly as
an argument to Make unless the 'override' directive is used, which is
ugly and different to what is done in the top-level Makefile.

Move the '--target' option for clang out of COMPATCC and into
VDSO_CAFLAGS, where it will be picked up when compiling and assembling
the 32-bit vDSO under clang.
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

KBUILD_CPPFLAGS is defined differently depending on whether the main
compiler is clang or not. This means that it is not possible to build
the compat vDSO with GCC if the rest of the kernel is built with clang.

Define VDSO_CPPFLAGS directly to break this dependency and allow a clang
kernel to build a compat vDSO with GCC:

  $ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- \
    CROSS_COMPILE_COMPAT=arm-linux-gnueabihf- CC=clang \
    COMPATCC=arm-linux-gnueabihf-gcc
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

There's no need to export COMPATCC, so just define it locally in the
vdso32/Makefile, which is the only place where it is used.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Rather than force the use of GCC for the compat cross-compiler, instead
extract the target from CROSS_COMPILE_COMPAT and pass it to clang if the
main compiler is clang.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

arm64 was the last architecture using CROSS_COMPILE_COMPAT_VDSO config
option. With this patch series the dependency in the architecture has
been removed.

Remove CROSS_COMPILE_COMPAT_VDSO from the Unified vDSO library code.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

The jump labels are not used in vdso32 since it is not possible to run
runtime patching on them.

Remove the configuration option from the Makefile.

Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Older versions of binutils (prior to 2.24) do not support the "ISHLD"
option for memory barrier instructions, which leads to a build failure
when assembling the vdso32 library.

Add a compilation time mechanism that detects if binutils supports those
instructions and configure the kernel accordingly.

Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Moving over to the generic C implementation of the vDSO inadvertently
left some stale files behind which are no longer used. Remove them.

Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

The .config file and the generated include/config/auto.conf can
end up out of sync after a set of commands since
CONFIG_CROSS_COMPILE_COMPAT_VDSO is not updated correctly.

The sequence can be reproduced as follows:

$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- defconfig
[...]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- menuconfig
[set CONFIG_CROSS_COMPILE_COMPAT_VDSO="arm-linux-gnueabihf-"]
$ make ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu-

Which results in:

arch/arm64/Makefile:62: CROSS_COMPILE_COMPAT not defined or empty,
the compat vDSO will not be built

even though the compat vDSO has been built:

$ file arch/arm64/kernel/vdso32/vdso.so
arch/arm64/kernel/vdso32/vdso.so: ELF 32-bit LSB pie executable, ARM,
EABI5 version 1 (SYSV), dynamically linked,
BuildID[sha1]=c67f6c786f2d2d6f86c71f708595594aa25247f6, stripped

A similar case that involves changing the configuration parameter
multiple times can be reconducted to the same family of problems.

Remove the use of CONFIG_CROSS_COMPILE_COMPAT_VDSO altogether and
instead rely on the cross-compiler prefix coming from the environment
via CROSS_COMPILE_COMPAT, much like we do for the rest of the kernel.

Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

When detecting a spurious EL1 translation fault, we attempt to compare
ESR_EL1.DFSC with PAR_EL1.FST. We erroneously use FIELD_PREP() to
extract PAR_EL1.FST, when we should be using FIELD_GET().

In the wise words of Robin Murphy:

| FIELD_GET() is a UBFX, FIELD_PREP() is a BFI

Using FIELD_PREP() means that that dfsc & ESR_ELx_FSC_TYPE is always
zero, and hence not equal to ESR_ELx_FSC_FAULT. Thus we detect any
unhandled translation fault as spurious.

... so let's use FIELD_GET() to ensure we don't decide all translation
faults are spurious. ESR_EL1.DFSC occupies bits [5:0], and requires no
shifting.

Fixes: 42f91093 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Robin Murphy <robin.murphy@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>

CPUs affected by Neoverse-N1 #1542419 may execute a stale instruction if
it was recently modified. The affected sequence requires freshly written
instructions to be executable before a branch to them is updated.

There are very few places in the kernel that modify executable text,
all but one come with sufficient synchronisation:
 * The module loader's flush_module_icache() calls flush_icache_range(),
   which does a kick_all_cpus_sync()
 * bpf_int_jit_compile() calls flush_icache_range().
 * Kprobes calls aarch64_insn_patch_text(), which does its work in
   stop_machine().
 * static keys and ftrace both patch between nops and branches to
   existing kernel code (not generated code).

The affected sequence is the interaction between ftrace and modules.
The module PLT is cleaned using __flush_icache_range() as the trampoline
shouldn't be executable until we update the branch to it.

Drop the double-underscore so that this path runs kick_all_cpus_sync()
too.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Commit bd82d4bd ("arm64: Fix incorrect irqflag restore for priority
masking") added a macro to the entry.S call paths that leave the
PSTATE.I bit set. This tells the pPNMI masking logic that interrupts
are masked by the CPU, not by the PMR. This value is read back by
local_daif_save().

Commit bd82d4bd added this call to el0_svc, as el0_svc_handler
is called with interrupts masked. el0_svc_compat was missed, but should
be covered in the same way as both of these paths end up in
el0_svc_common(), which expects to unmask interrupts.

Fixes: bd82d4bd ("arm64: Fix incorrect irqflag restore for priority masking")
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>

If we take an unhandled fault in the kernel, we call show_pte() to dump
the {PGDP,PGD,PUD,PMD,PTE} values for the corresponding page table walk,
where the PGDP value is virt_to_phys(mm->pgd).

The boot-time and runtime kernel page tables, init_pg_dir and
swapper_pg_dir respectively, are kernel symbols. Thus, it is not valid
to call virt_to_phys() on either of these, though we'll do so if we take
a fault on a TTBR1 address.

When CONFIG_DEBUG_VIRTUAL is not selected, virt_to_phys() will silently
fix this up. However, when CONFIG_DEBUG_VIRTUAL is selected, this
results in splats as below. Depending on when these occur, they can
happen to suppress information needed to debug the original unhandled
fault, such as the backtrace:

| Unable to handle kernel paging request at virtual address ffff7fffec73cf0f
| Mem abort info:
|   ESR = 0x96000004
|   EC = 0x25: DABT (current EL), IL = 32 bits
|   SET = 0, FnV = 0
|   EA = 0, S1PTW = 0
| Data abort info:
|   ISV = 0, ISS = 0x00000004
|   CM = 0, WnR = 0
| ------------[ cut here ]------------
| virt_to_phys used for non-linear address: 00000000102c9dbe (swapper_pg_dir+0x0/0x1000)
| WARNING: CPU: 1 PID: 7558 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0xe0/0x170 arch/arm64/mm/physaddr.c:12
| Kernel panic - not syncing: panic_on_warn set ...
| SMP: stopping secondary CPUs
| Dumping ftrace buffer:
|    (ftrace buffer empty)
| Kernel Offset: disabled
| CPU features: 0x0002,23000438
| Memory Limit: none
| Rebooting in 1 seconds..

We can avoid this by ensuring that we call __pa_symbol() for
init_mm.pgd, as this will always be a kernel symbol. As the dumped
{PGD,PUD,PMD,PTE} values are the raw values from the relevant entries we
don't need to handle these specially.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

The HWCAP framework will detect a new capability based on the sanitized
version of the ID registers.

Sanitization is based on a whitelist, so any field not described will end
up to be zeroed.

At the moment, ID_AA64ISAR1_EL1.FRINTTS is not described in
ftr_id_aa64isar1. This means the field will be zeroed and therefore the
userspace will not be able to see the HWCAP even if the hardware
supports the feature.

This can be fixed by describing the field in ftr_id_aa64isar1.

Fixes: ca9503fc ("arm64: Expose FRINT capabilities to userspace")
Signed-off-by: Julien Grall <julien.grall@arm.com>
Cc: mark.brown@arm.com
Signed-off-by: Will Deacon <will@kernel.org>

As of ac7c3e4f ("compiler: enable CONFIG_OPTIMIZE_INLINING forcibly"),
inline functions are no longer annotated with '__always_inline', which
allows the compiler to decide whether inlining is really a good idea or
not. Although this is a great idea on paper, the reality is that AArch64
GCC prior to 9.1 has been shown to get confused when creating an
out-of-line copy of a function passing explicit 'register' variables
into an inline assembly block:

  https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91111

It's not clear whether this is specific to arm64 or not but, for now,
ensure that all of our functions using 'register' variables are marked
as '__always_inline' so that the old behaviour is effectively preserved.

Hopefully other architectures are luckier with their compilers.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Will Deacon <will@kernel.org>

Sphinx generates the following warnings for the arm64 doc
pages:

Documentation/arm64/memory.rst:158: WARNING: Unexpected indentation.
Documentation/arm64/memory.rst:162: WARNING: Unexpected indentation.

These indentations warnings can be resolved by utilising code
hightlighting instead.
Signed-off-by: Adam Zerella <adam.zerella@gmail.com>
Signed-off-by: Will Deacon <will@kernel.org>

The system which has SVE feature crashed because of
the memory pointed by task->thread.sve_state was destroyed
by someone.

That is because sve_state is freed while the forking the
child process. The child process has the pointer of sve_state
which is same as the parent's because the child's task_struct
is copied from the parent's one. If the copy_process()
fails as an error on somewhere, for example, copy_creds(),
then the sve_state is freed even if the parent is alive.
The flow is as follows.

copy_process
        p = dup_task_struct
            => arch_dup_task_struct
                *dst = *src;  // copy the entire region.
:
        retval = copy_creds
        if (retval < 0)
                goto bad_fork_free;
:
bad_fork_free:
...
        delayed_free_task(p);
          => free_task
             => arch_release_task_struct
                => fpsimd_release_task
                   => __sve_free
                      => kfree(task->thread.sve_state);
                         // free the parent's sve_state

Move child's sve_state = NULL and clearing TIF_SVE flag
to arch_dup_task_struct() so that the child doesn't free the
parent's one.
There is no need to wait until copy_process() to clear TIF_SVE for
dst, because the thread flags for dst are initialized already by
copying the src task_struct.
This change simplifies the code, so get rid of comments that are no
longer needed.

As a note, arm64 used to have thread_info on the stack. So it
would not be possible to clear TIF_SVE until the stack is initialized.
From commit c02433dd ("arm64: split thread_info from task stack"),
the thread_info is part of the task, so it should be valid to modify
the flag from arch_dup_task_struct().

Cc: stable@vger.kernel.org # 4.15.x-
Fixes: bc0ee476 ("arm64/sve: Core task context handling")
Signed-off-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Reported-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Suggested-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>

Commit 73f38166 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") renamed the caller of the install_bp_hardening_cb() function
but forgot to update a comment, which can be confusing when trying to
follow the code flow.

Fixes: 73f38166 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Will Deacon <will@kernel.org>

Pull btrfs fixes from David Sterba:
 "A bunch of fixes that accumulated in recent weeks, mostly material for
  stable.

  Summary:

   - fix for regression from 5.3 that prevents to use balance convert
     with single profile

   - qgroup fixes: rescan race, accounting leak with multiple writers,
     potential leak after io failure recovery

   - fix for use after free in relocation (reported by KASAN)

   - other error handling fixups"

* tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls
  btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space
  btrfs: Fix a regression which we can't convert to SINGLE profile
  btrfs: relocation: fix use-after-free on dead relocation roots
  Btrfs: fix race setting up and completing qgroup rescan workers
  Btrfs: fix missing error return if writeback for extent buffer never started
  btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer
  Btrfs: fix selftests failure due to uninitialized i_mode in test inodes

Pull csky updates from Guo Ren:
 "This round of csky subsystem just some fixups:

   - Fix mb() synchronization problem

   - Fix dma_alloc_coherent with PAGE_SO attribute

   - Fix cache_op failed when cross memory ZONEs

   - Optimize arch_sync_dma_for_cpu/device with dma_inv_range

   - Fix ioremap function losing

   - Fix arch_get_unmapped_area() implementation

   - Fix defer cache flush for 610

   - Support kernel non-aligned access

   - Fix 610 vipt cache flush mechanism

   - Fix add zero_fp fixup perf backtrace panic

   - Move static keyword to the front of declaration

   - Fix csky_pmu.max_period assignment

   - Use generic free_initrd_mem()

   - entry: Remove unneeded need_resched() loop"

* tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux:
  csky: Move static keyword to the front of declaration
  csky: entry: Remove unneeded need_resched() loop
  csky: Fixup csky_pmu.max_period assignment
  csky: Fixup add zero_fp fixup perf backtrace panic
  csky: Use generic free_initrd_mem()
  csky: Fixup 610 vipt cache flush mechanism
  csky: Support kernel non-aligned access
  csky: Fixup defer cache flush for 610
  csky: Fixup arch_get_unmapped_area() implementation
  csky: Fixup ioremap function losing
  csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range
  csky/dma: Fixup cache_op failed when cross memory ZONEs
  csky: Fixup dma_alloc_coherent with PAGE_SO attribute
  csky: Fixup mb() synchronization problem

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes that have trickled in through the merge window:

   - Video fixes for OMAP due to panel-dpi driver removal

   - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7

   - Fixing arch version on ASpeed ast2500

   - Two fixes for reset handling on ARM SCMI"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
  ARM: aspeed: ast2500 is ARMv6K
  reset: reset-scmi: add missing handle initialisation
  firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset
  bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle()
  ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux
  ARM: dts: am3517-evm: Fix missing video
  ARM: dts: logicpd-torpedo-baseboard: Fix missing video
  ARM: omap2plus_defconfig: Fix missing video
  bus: ti-sysc: Fix handling of invalid clocks
  bus: ti-sysc: Fix clock handling for no-idle quirks

Pull tracing fixes from Steven Rostedt:
 "A few more tracing fixes:

   - Fix a buffer overflow by checking nr_args correctly in probes

   - Fix a warning that is reported by clang

   - Fix a possible memory leak in error path of filter processing

   - Fix the selftest that checks for failures, but wasn't failing

   - Minor clean up on call site output of a memory trace event"

* tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  selftests/ftrace: Fix same probe error test
  mm, tracing: Print symbol name for call_site in trace events
  tracing: Have error path in predicate_parse() free its allocated memory
  tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro
  tracing/probe: Fix to check the difference of nr_args before adding probe

Pull more MMC updates from Ulf Hansson:
 "A couple more updates/fixes for MMC:

   - sdhci-pci: Add Genesys Logic GL975x support

   - sdhci-tegra: Recover loss in throughput for DMA

   - sdhci-of-esdhc: Fix DMA bug"

* tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: host: sdhci-pci: Add Genesys Logic GL975x support
  mmc: tegra: Implement ->set_dma_mask()
  mmc: sdhci: Let drivers define their DMA mask
  mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence
  mmc: sdhci: improve ADMA error reporting

Move the static keyword to the front of declaration of
csky_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):

arch/csky/kernel/perf_event.c:1340:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Since the enabling and disabling of IRQs within preempt_schedule_irq()
is contained in a need_resched() loop, we don't need the outer arch
code loop.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Guo Ren <guoren@kernel.org>

Pull Documentation/process update from Greg KH:
 "Here are two small Documentation/process/embargoed-hardware-issues.rst
  file updates that missed my previous char/misc pull request.

  The first one adds an Intel representative for the process, and the
  second one cleans up the text a bit more when it comes to how the
  disclosure rules work, as it was a bit confusing to some companies"

* tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Documentation/process: Clarify disclosure rules
  Documentation/process: Volunteer as the ambassador for Intel

Pull more vfs updates from Al Viro:
 "A couple of misc patches"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  afs dynroot: switch to simple_dir_operations
  fs/handle.c - fix up kerneldoc

Pull more cifs updates from Steve French:
 "Fixes from the recent SMB3 Test events and Storage Developer
  Conference (held the last two weeks).

  Here are nine smb3 patches including an important patch for debugging
  traces with wireshark, with three patches marked for stable.

  Additional fixes from last week to better handle some newly discovered
  reparse points, and a fix the create/mkdir path for setting the mode
  more atomically (in SMB3 Create security descriptor context), and one
  for path name processing are still being tested so are not included
  here"

* tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix oplock handling for SMB 2.1+ protocols
  smb3: missing ACL related flags
  smb3: pass mode bits into create calls
  smb3: Add missing reparse tags
  CIFS: fix max ea value size
  fs/cifs/sess.c: Remove set but not used variable 'capabilities'
  fs/cifs/smb2pdu.c: Make SMB2_notify_init static
  smb3: fix leak in "open on server" perf counter
  smb3: allow decryption keys to be dumped by admin for debugging

The csky_pmu.max_period has type u64, and BIT() can only return
32 bits unsigned long on C-SKY. The initialization for max_period
will be incorrect when count_width is bigger than 32.

Use BIT_ULL()
Signed-off-by: Mao Han <han_mao@c-sky.com>
Signed-off-by: Guo Ren <ren_guo@c-sky.com>

We need set fp zero to let backtrace know the end. The patch fixup perf
callchain panic problem, because backtrace didn't know what is the end
of fp.
Signed-off-by: Guo Ren <ren_guo@c-sky.com>
Reported-by: Mao Han <han_mao@c-sky.com>