There is nothing being done after the `err_predisable` label, so just
remove it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADL5240 is a high performance, digitally controlled variable gain
amplifier (VGA) operating from 100 MHz to 4000 MHz. The VGA integrates a
high performance, 20 dB gain, internally matched amplifier (AMP) with a
6-bit digital step attenuator (DSA) that has a gain control range of
31.5 dB in 0.5 dB steps with ±0.25 dB step accuracy.

Datasheet link:
  https://www.analog.com/media/en/technical-documentation/data-sheets/adl5240.pdfSigned-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This change adds support for the ADA4961 BiCMOS RF Digital Gain Amplifier,
(DGA), which is optimized for driving heavy loads out 2.0 GHz and beyond.
The device typically achieves -90 dBc IMD3 performance at 500 MHz and
-85  dBc at 1.5 GHz.

Datasheet link:
 http://www.analog.com/media/en/technical-documentation/data-sheets/ADA4961.pdf

This change re-uses the existing ad8366 driver, as most logic is similar.
Also, this chip has a reset pin which is initialized during probe.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The SPI gain amplifiers are simple devices, with 1 or 2 channels, to which
are read-from/written-to.

The gain computation in ad8366_write_raw() has been updated to compute gain
in dB for negative values.

This driver will be extended to support other chips as well.
To do that, this rework handles the AD8366 device as a special-case (via
switch-statements). This will make things easier when adding new chips.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This driver is still using iio_dev's mlock to guard against inconsistent
state. This has been discouraged for some time.

This change switches to using it's own mutex, defined on the state struct.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Use the new `SPDX-License-Identifier` tag to specify the license.
For ad8366, also update copyright years in the header part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Convert the old device tree documentation to yaml format.
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Rodrigo Ribeiro <rodrigorsdc@gmail.com>
Co-developed-by: Rodrigo Ribeiro <rodrigorsdc@gmail.com>
Reviewed-by: Matheus Tavares <matheus.bernardino@usp.br>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The iio_triggered_buffer_{predisable,postenable} functions attach/detach
the poll functions.

For the predisable hook, the disable code should occur before detaching
the poll func, and for the postenable hook, the poll func should be
attached before the enable code.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Document support for Analog Devices ADF4371 SPI Wideband Synthesizer.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The ADF4371 is a frequency synthesizer with an integrated voltage
controlled oscillator (VCO) for phase-locked loops (PLLs). The ADF4371
has an integrated VCO with a fundamental output frequency ranging from
4000 MHz to 8000 MHz. In addition, the VCO frequency is connected to
divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allows the user to
generate radio frequency (RF) output frequencies as low as 62.5 MHz at
RF8x. A frequency multiplier at RF16x generates from 8 GHz to 16 GHz. A
frequency quadrupler generates frequencies from 16 GHz to 32 GHz at RF32x.
RFAUX8x duplicates the frequency range of RF8x or permits direct access to
the VCO output.

The driver takes the reference input frequency from the device tree and
uses it to calculate and maximize the PFD frequency (frequency of the phase
frequency detector). The PFD frequency is further used to calculate the
timeouts: synthesizer lock, VCO band selection, automatic level
calibration (ALC) and PLL settling time.

This initial driver exposes the attributes for setting the frequency and
enabling/disabling the different adf4371 channels.

Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adf4371.pdfSigned-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Introduce sensor name in st_lsm6dsx_sensor_settings table. This is
a preliminary patch to add I3C support to st_lsm6dsx since i3c_device_id
data structure does not contain a name field
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

average_en is always true, so there is not really need for
this structure member.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

All the parameters of devm_request_irq() can fit into a
single line, so place them all in a single line
for better readability.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Since the input clock is always 24MHz, there is no need for storing
this value into a variable.

Use a definition instead, which is more appropriate in this case.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

In case of ioremap failure, the core code will take care of printing
the error message, so there is no need for having a local error
message in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The stk3335 light/proximity sensor is similar to the stk3310 and stk3311
sensors and works with the stk3310 driver.
Signed-off-by: Martijn Braam <martijn@brixit.nl>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The incorrect limit for the for_each_set_bit loop was noticed whilst fixing
this other case.  Note that as we only have 3 possible entries a the moment
and the value was set to 4, the bug would not have any effect currently.
It will bite fairly soon though, so best fix it now.

See commit ef4b4856 ("iio:core: Fix bug in length of event info_mask and
catch unhandled bits set in masks.") for details.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The driver only needs to access GPIOs via GPIOLIB. And SPI can be
configured via device-tree or ACPI.

The platform data is a remnant from another time, and should not cause the
driver to error out during probing if it is NULL.
Also, it's not used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Because this driver will support multiple configurations for software,
the software configuration was made generic.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The device dependent options which are going to be different for devices
which will be supported  in the future by this driver,
were moved in chip info for a more generic driver. This patch allows
supporting more devices by the driver. Also, it is an intermediate
step of adding support for ad7616 in software mode.
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds a MAINTAINERS entry for the AD7780 ADC driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds a YAML binding for the Analog Devices AD7780/1 and
AD7170/1 analog-to-digital converters.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Some ultrabooks, like Teclast F6 Pro, use KIOX010A sensor on display
and KIOX020A sensor on keyboard base, to detect tablet mode or screen
orientation.
Signed-off-by: Luís Ferreira <luis@aurorafoss.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The documentation give some exemple on what format can be expected
from sampling_frequency_available sysfs attribute
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The DPS310 supports measurement of pressure, so support that in the
driver. Use background measurement like the temperature sensing and
default to lowest precision and lowest measurement rate.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a manufacturer's suggested workaround to deal with early revisions
of chip that don't indicate correct temperature. Readings can be in the
~60C range when they should be in the ~20's.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

The DPS310 is a temperature and pressure sensor. It can be accessed over
i2c and SPI, but this driver only supports polling over i2c.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

This patch adds of_match_table entry in device driver in order to
enable spi fallback probing.
Signed-off-by: Rodrigo Ribeiro <rodrigorsdc@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a of_device_id struct variable and subsequent call to
MODULE_DEVICE_TABLE macro to support device tree.
Signed-off-by: João Seckler <joaoseckler@gmail.com>
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Co-developed-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a of_device_id struct and MODULE_DEVICE_TABLE call, in order to add
device-tree support for this driver.
Signed-off-by: Lucas Oshiro <lucasseikioshiro@gmail.com>
Signed-off-by: Rodrigo Ribeiro <rodrigorsdc@gmail.com>
Co-developed-by: Rodrigo Ribeiro <rodrigorsdc@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Create structure of type of_device_id in order to register all devices
the driver is able to manage.
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Wilson Sales <spoonm@spoonm.org>
Co-developed-by: Wilson Sales <spoonm@spoonm.org>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Accomplish device tree compatibility to driver ADIS16203
by adding of_device_id table and making a subsequent call to
MODULE_DEVICE_TABLE.
Signed-off-by: Thiago Estrela <thiagestrela@gmail.com>
Signed-off-by: Tiago Napoli <napoli.tiago96@gmail.com>
Co-developed-by: Tiago Napoli <napoli.tiago96@gmail.com>
Signed-off-by: Pedro Sousa <pedroteosousa@gmail.com>
Co-developed-by: Pedro Sousa <pedroteosousa@gmail.com>
Reviewed-by: Matheus Tavares <matheus.bernardino@usp.br>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add a of_device_id struct array of_match_table variable and subsequent
call to MODULE_DEVICE_TABLE macro to enable explicit device tree support.
Co-developed-by: Thiago L. A. Miller <tmiller@mochsl.org.br>
Signed-off-by: Thiago L. A. Miller <tmiller@mochsl.org.br>
Co-developed-by: Osvaldo M. Yasuda <omyasuda@yahoo.com.br>
Signed-off-by: Osvaldo M. Yasuda <omyasuda@yahoo.com.br>
Signed-off-by: João Victor Marques de Oliveira <joao.marques.oliveira@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Create macro for capacitance channels in order to remove the repeated
code and improve its readability.
Signed-off-by: Bárbara Fernandes <barbara.fernandes@usp.br>
Signed-off-by: Wilson Sales <spoonm@spoonm.org>
Co-developed-by: Wilson Sales <spoonm@spoonm.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add myself as the maintainer of the anybuss bus driver, and its client
drivers.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add myself as the maintainer of the fieldbus subsystem.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes checkpatch.pl warning "Possible unnecessary 'out of memory'
message".
Signed-off-by: Simon Sandström <simon@nikanor.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixes checkpatch.pl warning "Use #include <linux/io.h> instead of
<asm/io.h>".
Signed-off-by: Simon Sandström <simon@nikanor.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>