- 26 Jul, 2019 40 commits
-
-
Finn Thain authored
commit 25fcf94a upstream. This reverts commit 4822827a. The purpose of that commit was to suppress a timeout warning message which appeared to be caused by target latency. But suppressing the warning is undesirable as the warning may indicate a messed up transfer count. Another problem with that commit is that 15 ms is too long to keep interrupts disabled as interrupt latency can cause system clock drift and other problems. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org Fixes: 4822827a ("scsi: ncr5380: Increase register polling limit") Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Tested-by:
Stan Johnson <userm57@yahoo.com> Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Finn Thain authored
commit f9dfed1c upstream. A PDMA error is handled in the core driver by setting the device's 'borken' flag and aborting the command. Unfortunately, do_abort() is not dependable. Perform a SCSI bus reset instead, to make sure that the command fails and gets retried. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.20+ Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Finn Thain authored
commit 57f31326 upstream. The reselection interrupt gets disabled during selection and must be re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a disconnected command may time-out or the target may wedge the bus while trying to reselect the host. This can happen after a command is aborted. Fix this by enabling the reselection interrupt in NCR5380_main() after calls to NCR5380_select() and NCR5380_information_transfer() return. Cc: Michael Schmitz <schmitzmic@gmail.com> Cc: stable@vger.kernel.org # v4.9+ Fixes: 8b00c3d5 ("ncr5380: Implement new eh_abort_handler") Signed-off-by:
-
Juergen Gross authored
commit a1078e82 upstream. Instead of trying to allocate pages with GFP_USER in add_ballooned_pages() check the available free memory via si_mem_available(). GFP_USER is far less limiting memory exhaustion than the test via si_mem_available(). This will avoid dom0 running out of memory due to excessive foreign page mappings especially on ARM and on x86 in PVH mode, as those don't have a pre-ballooned area which can be used for foreign mappings. As the normal ballooning suffers from the same problem don't balloon down more than si_mem_available() pages in one iteration. At the same time limit the default maximum number of retries. This is part of XSA-300. Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Denis Efremov authored
[ Upstream commit da99466a ] This fixes a global out-of-bounds read access in the copy_buffer function of the floppy driver. The FDDEFPRM ioctl allows one to set the geometry of a disk. The sect and head fields (unsigned int) of the floppy_drive structure are used to compute the max_sector (int) in the make_raw_rw_request function. It is possible to overflow the max_sector. Next, max_sector is passed to the copy_buffer function and used in one of the memcpy calls. An unprivileged user could trigger the bug if the device is accessible, but requires a floppy disk to be inserted. The patch adds the check for the .sect * .head multiplication for not overflowing in the set_geometry function. The bug was found by syzkaller. Signed-off-by:
Denis Efremov <efremov@ispras.ru> Tested-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Denis Efremov authored
[ Upstream commit 9b04609b ] This fixes the invalid pointer dereference in the drive_name function of the floppy driver. The native_format field of the struct floppy_drive_params is used as floppy_type array index in the drive_name function. Thus, the field should be checked the same way as the autodetect field. To trigger the bug, one could use a value out of range and set the drive parameters with the FDSETDRVPRM ioctl. Next, FDGETDRVTYP ioctl should be used to call the drive_name. A floppy disk is not required to be inserted. CAP_SYS_ADMIN is required to call FDSETDRVPRM. The patch adds the check for a value of the native_format field to be in the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices. The bug was found by syzkaller. Signed-off-by:
-
Denis Efremov authored
[ Upstream commit 5635f897 ] This fixes a global out-of-bounds read access in the next_valid_format function of the floppy driver. The values from autodetect field of the struct floppy_drive_params are used as indices for the floppy_type array in the next_valid_format function 'floppy_type[DP->autodetect[probed_format]].sect'. To trigger the bug, one could use a value out of range and set the drive parameters with the FDSETDRVPRM ioctl. A floppy disk is not required to be inserted. CAP_SYS_ADMIN is required to call FDSETDRVPRM. The patch adds the check for values of the autodetect field to be in the '0 <= x < ARRAY_SIZE(floppy_type)' range of the floppy_type array indices. The bug was found by syzkaller. Signed-off-by:
-
Denis Efremov authored
[ Upstream commit f3554aeb ] This fixes a divide by zero error in the setup_format_params function of the floppy driver. Two consecutive ioctls can trigger the bug: The first one should set the drive geometry with such .sect and .rate values for the F_SECT_PER_TRACK to become zero. Next, the floppy format operation should be called. A floppy disk is not required to be inserted. An unprivileged user could trigger the bug if the device is accessible. The patch checks F_SECT_PER_TRACK for a non-zero value in the set_geometry function. The proper check should involve a reasonable upper limit for the .sect and .rate fields, but it could change the UAPI. The patch also checks F_SECT_PER_TRACK in the setup_format_params, and cancels the formatting operation in case of zero. The bug was found by syzkaller. Signed-off-by:
-
Andrii Nakryiko authored
[ Upstream commit 763ff0e7 ] Similar issue was fixed in cdfc7f88 ("libbpf: fix GCC8 warning for strncpy") already. This one was missed. Fixing now. Cc: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by:
Andrii Nakryiko <andriin@fb.com> Acked-by:
Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
-
Dennis Zhou authored
[ Upstream commit c9b3007f ] The iolatency controller is based on rq_qos. It increments on rq_qos_throttle() and decrements on either rq_qos_cleanup() or rq_qos_done_bio(). a3fb01ba fixes the double accounting issue where blk_mq_make_request() may call both rq_qos_cleanup() and rq_qos_done_bio() on REQ_NO_WAIT. So checking STS_AGAIN prevents the double decrement. The above works upstream as the only way we can get STS_AGAIN is from blk_mq_get_request() failing. The STS_AGAIN handling isn't a real problem as bio_endio() skipping only happens on reserved tag allocation failures which can only be caused by driver bugs and already triggers WARN. However, the fix creates a not so great dependency on how STS_AGAIN can be propagated. Internally, we (Facebook) carry a patch that kills read ahead if a cgroup is io congested or a fatal signal is pending. This combined with chained bios progagate their bi_status to the parent is not already set can can cause the parent bio to not clean up properly even though it was successful. This consequently leaks the inflight counter and can hang all IOs under that blkg. To nip the adverse interaction early, this removes the rq_qos_cleanup() callback in iolatency in favor of cleaning up always on the rq_qos_done_bio() path. Fixes: a3fb01ba ("blk-iolatency: only account submitted bios") Debugged-by:
Tejun Heo <tj@kernel.org> Debugged-by:
Josef Bacik <josef@toxicpanda.com> Signed-off-by:
Dennis Zhou <dennis@kernel.org> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit 9fe06a51 ] A recent commit efa14c39 ("iavf: allow null RX descriptors") added a null pointer sanity check on rx_buffer, however, rx_buffer is being dereferenced before that check, which implies a null pointer dereference bug can potentially occur. Fix this by only dereferencing rx_buffer until after the null pointer check. Addresses-Coverity: ("Dereference before null check") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Huazhong Tan authored
[ Upstream commit f96315f2 ] When change MTU or other operations, which just calling .reset_notify to do HNAE3_DOWN_CLIENT and HNAE3_UP_CLIENT, then the netdev_tx_reset_queue() in the hns3_clear_all_ring() will be ignored. So the dev_watchdog() may misdiagnose a TX timeout. This patch separates netdev_tx_reset_queue() from hns3_clear_all_ring(), and unifies hns3_clear_all_ring() and hns3_force_clear_all_ring into one, since they are doing similar things. Fixes: 3a30964a ("net: hns3: delay ring buffer clearing during reset") Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Josua Mayer authored
[ Upstream commit 433a06d7 ] Defer probing of the orion-mdio interface when getting a clock returns EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used before all clocks have been enabled. Signed-off-by:
Josua Mayer <josua@solid-run.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Ilya Maximets authored
[ Upstream commit bf0bdd13 ] Unlike driver mode, generic xdp receive could be triggered by different threads on different CPU cores at the same time leading to the fill and rx queue breakage. For example, this could happen while sending packets from two processes to the first interface of veth pair while the second part of it is open with AF_XDP socket. Need to take a lock for each generic receive to avoid race. Fixes: c497176c ("xsk: add Rx receive functions and poll support") Signed-off-by:
Ilya Maximets <i.maximets@samsung.com> Acked-by:
William Tu <u9012063@gmail.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit a2bed907 ] Current gtp_newlink() could be called after unregister_pernet_subsys(). gtp_newlink() uses gtp_net but it can be destroyed by unregister_pernet_subsys(). So unregister_pernet_subsys() should be called after rtnl_link_unregister(). Test commands: #SHELL 1 while : do for i in {1..5} do ./gtp-link add gtp$i & done killall gtp-link done #SHELL 2 while : do modprobe -rv gtp done Splat looks like: [ 753.176631] BUG: KASAN: use-after-free in gtp_newlink+0x9b4/0xa5c [gtp] [ 753.177722] Read of size 8 at addr ffff8880d48f2458 by task gtp-link/7126 [ 753.179082] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G W 5.2.0-rc6+ #50 [ 753.185801] Call Trace: [ 753.186264] dump_stack+0x7c/0xbb [ 753.186863] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.187583] print_address_description+0xc7/0x240 [ 753.188382] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.189097] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.189846] __kasan_report+0x12a/0x16f [ 753.190542] ? gtp_newlink+0x9b4/0xa5c [gtp] [ 753.191298] kasan_report+0xe/0x20 [ 753.191893] gtp_newlink+0x9b4/0xa5c [gtp] [ 753.192580] ? __netlink_ns_capable+0xc3/0xf0 [ 753.193370] __rtnl_newlink+0xb9f/0x11b0 [ ... ] [ 753.241201] Allocated by task 7186: [ 753.241844] save_stack+0x19/0x80 [ 753.242399] __kasan_kmalloc.constprop.3+0xa0/0xd0 [ 753.243192] __kmalloc+0x13e/0x300 [ 753.243764] ops_init+0xd6/0x350 [ 753.244314] register_pernet_operations+0x249/0x6f0 [ ... ] [ 753.251770] Freed by task 7178: [ 753.252288] save_stack+0x19/0x80 [ 753.252833] __kasan_slab_free+0x111/0x150 [ 753.253962] kfree+0xc7/0x280 [ 753.254509] ops_free_list.part.11+0x1c4/0x2d0 [ 753.255241] unregister_pernet_operations+0x262/0x390 [ ... ] [ 753.285883] list_add corruption. next->prev should be prev (ffff8880d48f2458), but was ffff8880d497d878. (next. [ 753.287241] ------------[ cut here ]------------ [ 753.287794] kernel BUG at lib/list_debug.c:25! [ 753.288364] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 753.289099] CPU: 0 PID: 7126 Comm: gtp-link Tainted: G B W 5.2.0-rc6+ #50 [ 753.291036] RIP: 0010:__list_add_valid+0x74/0xd0 [ 753.291589] Code: 48 39 da 75 27 48 39 f5 74 36 48 39 dd 74 31 48 83 c4 08 b8 01 00 00 00 5b 5d c3 48 89 d9 48b [ 753.293779] RSP: 0018:ffff8880cae8f398 EFLAGS: 00010286 [ 753.294401] RAX: 0000000000000075 RBX: ffff8880d497d878 RCX: 0000000000000000 [ 753.296260] RDX: 0000000000000075 RSI: 0000000000000008 RDI: ffffed10195d1e69 [ 753.297070] RBP: ffff8880cd250ae0 R08: ffffed101b4bff21 R09: ffffed101b4bff21 [ 753.297899] R10: 0000000000000001 R11: ffffed101b4bff20 R12: ffff8880d497d878 [ 753.298703] R13: 0000000000000000 R14: ffff8880cd250ae0 R15: ffff8880d48f2458 [ 753.299564] FS: 00007f5f79805740(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000 [ 753.300533] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 753.301231] CR2: 00007fe8c7ef4f10 CR3: 00000000b71a6006 CR4: 00000000000606f0 [ 753.302183] Call Trace: [ 753.302530] gtp_newlink+0x5f6/0xa5c [gtp] [ 753.303037] ? __netlink_ns_capable+0xc3/0xf0 [ 753.303576] __rtnl_newlink+0xb9f/0x11b0 [ 753.304092] ? rtnl_link_unregister+0x230/0x230 Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit 1788b856 ] gtp_encap_destroy() is called twice. 1. When interface is deleted. 2. When udp socket is destroyed. either gtp->sk0 or gtp->sk1u could be freed by sock_put() in gtp_encap_destroy(). so, when gtp_encap_destroy() is called again, it would uses freed sk pointer. patch makes gtp_encap_destroy() to set either gtp->sk0 or gtp->sk1u to null. in addition, both gtp->sk0 and gtp->sk1u pointer are protected by rtnl_lock. so, rtnl_lock() is added. Test command: gtp-link add gtp1 & killall gtp-link ip link del gtp1 Splat looks like: [ 83.182767] BUG: KASAN: use-after-free in __lock_acquire+0x3a20/0x46a0 [ 83.184128] Read of size 8 at addr ffff8880cc7d5360 by task ip/1008 [ 83.185567] CPU: 1 PID: 1008 Comm: ip Not tainted 5.2.0-rc6+ #50 [ 83.188469] Call Trace: [ ... ] [ 83.200126] lock_acquire+0x141/0x380 [ 83.200575] ? lock_sock_nested+0x3a/0xf0 [ 83.201069] _raw_spin_lock_bh+0x38/0x70 [ 83.201551] ? lock_sock_nested+0x3a/0xf0 [ 83.202044] lock_sock_nested+0x3a/0xf0 [ 83.202520] gtp_encap_destroy+0x18/0xe0 [gtp] [ 83.203065] gtp_encap_disable.isra.14+0x13/0x50 [gtp] [ 83.203687] gtp_dellink+0x56/0x170 [gtp] [ 83.204190] rtnl_delete_link+0xb4/0x100 [ ... ] [ 83.236513] Allocated by task 976: [ 83.236925] save_stack+0x19/0x80 [ 83.237332] __kasan_kmalloc.constprop.3+0xa0/0xd0 [ 83.237894] kmem_cache_alloc+0xd8/0x280 [ 83.238360] sk_prot_alloc.isra.42+0x50/0x200 [ 83.238874] sk_alloc+0x32/0x940 [ 83.239264] inet_create+0x283/0xc20 [ 83.239684] __sock_create+0x2dd/0x540 [ 83.240136] __sys_socket+0xca/0x1a0 [ 83.240550] __x64_sys_socket+0x6f/0xb0 [ 83.240998] do_syscall_64+0x9c/0x450 [ 83.241466] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 83.242061] [ 83.242249] Freed by task 0: [ 83.242616] save_stack+0x19/0x80 [ 83.243013] __kasan_slab_free+0x111/0x150 [ 83.243498] kmem_cache_free+0x89/0x250 [ 83.244444] __sk_destruct+0x38f/0x5a0 [ 83.245366] rcu_core+0x7e9/0x1c20 [ 83.245766] __do_softirq+0x213/0x8fa Fixes: 1e3a3abd ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit 3f167e19 ] ipv4_pdp_add() is called in RCU read-side critical section. So GFP_KERNEL should not be used in the function. This patch make ipv4_pdp_add() to use GFP_ATOMIC instead of GFP_KERNEL. Test commands: gtp-link add gtp1 & gtp-tunnel add gtp1 v1 100 200 1.1.1.1 2.2.2.2 Splat looks like: [ 130.618881] ============================= [ 130.626382] WARNING: suspicious RCU usage [ 130.626994] 5.2.0-rc6+ #50 Not tainted [ 130.627622] ----------------------------- [ 130.628223] ./include/linux/rcupdate.h:266 Illegal context switch in RCU read-side critical section! [ 130.629684] [ 130.629684] other info that might help us debug this: [ 130.629684] [ 130.631022] [ 130.631022] rcu_scheduler_active = 2, debug_locks = 1 [ 130.632136] 4 locks held by gtp-tunnel/1025: [ 130.632925] #0: 000000002b93c8b7 (cb_lock){++++}, at: genl_rcv+0x15/0x40 [ 130.634159] #1: 00000000f17bc999 (genl_mutex){+.+.}, at: genl_rcv_msg+0xfb/0x130 [ 130.635487] #2: 00000000c644ed8e (rtnl_mutex){+.+.}, at: gtp_genl_new_pdp+0x18c/0x1150 [gtp] [ 130.636936] #3: 0000000007a1cde7 (rcu_read_lock){....}, at: gtp_genl_new_pdp+0x187/0x1150 [gtp] [ 130.638348] [ 130.638348] stack backtrace: [ 130.639062] CPU: 1 PID: 1025 Comm: gtp-tunnel Not tainted 5.2.0-rc6+ #50 [ 130.641318] Call Trace: [ 130.641707] dump_stack+0x7c/0xbb [ 130.642252] ___might_sleep+0x2c0/0x3b0 [ 130.642862] kmem_cache_alloc_trace+0x1cd/0x2b0 [ 130.643591] gtp_genl_new_pdp+0x6c5/0x1150 [gtp] [ 130.644371] genl_family_rcv_msg+0x63a/0x1030 [ 130.645074] ? mutex_lock_io_nested+0x1090/0x1090 [ 130.645845] ? genl_unregister_family+0x630/0x630 [ 130.646592] ? debug_show_all_locks+0x2d0/0x2d0 [ 130.647293] ? check_flags.part.40+0x440/0x440 [ 130.648099] genl_rcv_msg+0xa3/0x130 [ ... ] Fixes: 459aa660 ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit e198987e ] gtp_encap_enable_socket() and gtp_encap_destroy() are not protected by rcu_read_lock(). and it's not safe to write sk->sk_user_data. This patch make these functions to use lock_sock() instead of rcu_dereference_sk_user_data(). Test commands: gtp-link add gtp1 Splat looks like: [ 83.238315] ============================= [ 83.239127] WARNING: suspicious RCU usage [ 83.239702] 5.2.0-rc6+ #49 Not tainted [ 83.240268] ----------------------------- [ 83.241205] drivers/net/gtp.c:799 suspicious rcu_dereference_check() usage! [ 83.243828] [ 83.243828] other info that might help us debug this: [ 83.243828] [ 83.246325] [ 83.246325] rcu_scheduler_active = 2, debug_locks = 1 [ 83.247314] 1 lock held by gtp-link/1008: [ 83.248523] #0: 0000000017772c7f (rtnl_mutex){+.+.}, at: __rtnl_newlink+0x5f5/0x11b0 [ 83.251503] [ 83.251503] stack backtrace: [ 83.252173] CPU: 0 PID: 1008 Comm: gtp-link Not tainted 5.2.0-rc6+ #49 [ 83.253271] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 83.254562] Call Trace: [ 83.254995] dump_stack+0x7c/0xbb [ 83.255567] gtp_encap_enable_socket+0x2df/0x360 [gtp] [ 83.256415] ? gtp_find_dev+0x1a0/0x1a0 [gtp] [ 83.257161] ? memset+0x1f/0x40 [ 83.257843] gtp_newlink+0x90/0xa21 [gtp] [ 83.258497] ? __netlink_ns_capable+0xc3/0xf0 [ 83.259260] __rtnl_newlink+0xb9f/0x11b0 [ 83.260022] ? rtnl_link_unregister+0x230/0x230 [ ... ] Fixes: 1e3a3abd ("gtp: make GTP sockets in gtp_newlink optional") Signed-off-by:
-
csonsino authored
[ Upstream commit c49a8682 ] Problem: The Linux Bluetooth stack yields complete control over the BLE connection interval to the remote device. The Linux Bluetooth stack provides access to the BLE connection interval min and max values through /sys/kernel/debug/bluetooth/hci0/ conn_min_interval and /sys/kernel/debug/bluetooth/hci0/conn_max_interval. These values are used for initial BLE connections, but the remote device has the ability to request a connection parameter update. In the event that the remote side requests to change the connection interval, the Linux kernel currently only validates that the desired value is within the acceptable range in the Bluetooth specification (6 - 3200, corresponding to 7.5ms - 4000ms). There is currently no validation that the desired value requested by the remote device is within the min/max limits specified in the conn_min_interval/conn_max_interval configurations. This essentially leads to Linux yielding complete control over the connection interval to the remote device. The proposed patch adds a verification step to the connection parameter update mechanism, ensuring that the desired value is within the min/max bounds of the current connection. If the desired value is outside of the current connection min/max values, then the connection parameter update request is rejected and the negative response is returned to the remote device. Recall that the initial connection is established using the local conn_min_interval/conn_max_interval values, so this allows the Linux administrator to retain control over the BLE connection interval. The one downside that I see is that the current default Linux values for conn_min_interval and conn_max_interval typically correspond to 30ms and 50ms respectively. If this change were accepted, then it is feasible that some devices would no longer be able to negotiate to their desired connection interval values. This might be remedied by setting the default Linux conn_min_interval and conn_max_interval values to the widest supported range (6 - 3200 / 7.5ms - 4000ms). This could lead to the same behavior as the current implementation, where the remote device could request to change the connection interval value to any value that is permitted by the Bluetooth specification, and Linux would accept the desired value. Signed-off-by:
Carey Sonsino <csonsino@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Taehee Yoo authored
[ Upstream commit e30155fd ] If an invalid role is sent from user space, gtp_encap_enable() will fail. Then, it should call gtp_encap_disable_sock() but current code doesn't. It makes memory leak. Fixes: 91ed81f9 ("gtp: support SGSN-side tunnels") Signed-off-by:
-
Dan Carpenter authored
[ Upstream commit dcae9052 ] This change is similar to commit a1616a5a ("Bluetooth: hidp: fix buffer overflow") but for the compat ioctl. We take a string from the user and forgot to ensure that it's NUL terminated. I have also changed the strncpy() in to strscpy() in hidp_setup_hid(). The difference is the strncpy() doesn't necessarily NUL terminate the destination string. Either change would fix the problem but it's nice to take a belt and suspenders approach and do both. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Matias Karhumaa authored
[ Upstream commit 28261da8 ] Because of both sides doing L2CAP disconnection at the same time, it was possible to receive L2CAP Disconnection Response with CID that was already freed. That caused problems if CID was already reused and L2CAP Connection Request with same CID was sent out. Before this patch kernel deleted channel context regardless of the state of the channel. Example where leftover Disconnection Response (frame #402) causes local device to delete L2CAP channel which was not yet connected. This in turn confuses remote device's stack because same CID is re-used without properly disconnecting. Btmon capture before patch: ** snip ** > ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062 Channel: 65 len 4 [PSM 3 mode 0] {chan 2} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499 L2CAP: Disconnection Request (0x06) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548 L2CAP: Disconnection Response (0x07) ident 26 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 = bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447 > HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397 L2CAP: Connection Request (0x02) ident 27 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441 L2CAP: Connection Response (0x03) ident 27 len 8 Destination CID: 65 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449 L2CAP: Configure Request (0x04) ident 19 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Similar case after the patch: *snip* > ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Disconnect (DISC) (0x43) Address: 0x03 cr 1 dlci 0x00 Control: 0x53 poll/final 1 Length: 0 FCS: 0xfd < ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136 Channel: 65 len 4 [PSM 3 mode 0] {chan 3} RFCOMM: Unnumbered Ack (UA) (0x63) Address: 0x03 cr 1 dlci 0x00 Control: 0x73 poll/final 1 Length: 0 FCS: 0xd7 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143 L2CAP: Disconnection Request (0x06) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674 L2CAP: Disconnection Request (0x06) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762 L2CAP: Disconnection Response (0x07) ident 17 len 4 Destination CID: 65 Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073 L2CAP: Connection Request (0x02) ident 12 len 4 PSM: 1 (0x0001) Source CID: 65 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371 L2CAP: Disconnection Response (0x07) ident 11 len 4 Destination CID: 65 Source CID: 65 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082 Num handles: 1 Handle: 43 Count: 1 > HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040 Num handles: 1 Handle: 43 Count: 1 > ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103 L2CAP: Connection Request (0x02) ident 18 len 4 PSM: 3 (0x0003) Source CID: 65 < ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186 L2CAP: Connection Response (0x03) ident 18 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) < ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196 L2CAP: Configure Request (0x04) ident 13 len 19 Destination CID: 65 Flags: 0x0000 Option: Maximum Transmission Unit (0x01) [mandatory] MTU: 1013 Option: Retransmission and Flow Control (0x04) [mandatory] Mode: Basic (0x00) TX window size: 0 Max transmit: 0 Retransmission timeout: 0 Monitor timeout: 0 Maximum PDU size: 0 > ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804 L2CAP: Connection Response (0x03) ident 12 len 8 Destination CID: 66 Source CID: 65 Result: Connection successful (0x0000) Status: No further information available (0x0000) *snip* Fix is to check that channel is in state BT_DISCONN before deleting the channel. This bug was found while fuzzing Bluez's OBEX implementation using Synopsys Defensics. Reported-by:
Matti Kamunen <matti.kamunen@synopsys.com> Reported-by:
Ari Timonen <ari.timonen@synopsys.com> Signed-off-by:
Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by:
-
Seeteena Thoufeek authored
[ Upstream commit bff5a556 ] 'probe libc's inet_pton & backtrace it with ping' testcase sometimes fails on powerpc because distro ping binary does not have symbol information and thus it prints "[unknown]" function name in the backtrace. Accept "[unknown]" as valid function name for powerpc as well. # perf test -v "probe libc's inet_pton & backtrace it with ping" Before: 59: probe libc's inet_pton & backtrace it with ping : --- start --- test child forked, pid 79695 ping 79718 [077] 96483.787025: probe_libc:inet_pton: (7fff83a754c8) 7fff83a754c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so) 7fff83a2b7a0 gaih_inet.constprop.7+0x1020 (/usr/lib64/power9/libc-2.28.so) 7fff83a2c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so) 1171830f4 [unknown] (/usr/bin/ping) FAIL: expected backtrace entry ".*\+0x[[:xdigit:]]+[[:space:]]\(.*/bin/ping.*\)$" got "1171830f4 [unknown] (/usr/bin/ping)" test child finished with -1 ---- end ---- probe libc's inet_pton & backtrace it with ping: FAILED! After: 59: probe libc's inet_pton & backtrace it with ping : --- start --- test child forked, pid 79085 ping 79108 [045] 96400.214177: probe_libc:inet_pton: (7fffbb9654c8) 7fffbb9654c8 __GI___inet_pton+0x8 (/usr/lib64/power9/libc-2.28.so) 7fffbb91b7a0 gaih_inet.constprop.7+0x1020 (/usr/lib64/power9/libc-2.28.so) 7fffbb91c170 getaddrinfo+0x160 (/usr/lib64/power9/libc-2.28.so) 132e830f4 [unknown] (/usr/bin/ping) test child finished with 0 ---- end ---- probe libc's inet_pton & backtrace it with ping: Ok Signed-off-by:
Seeteena Thoufeek <s1seetee@linux.vnet.ibm.com> Reviewed-by:
Kim Phillips <kim.phillips@amd.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sandipan Das <sandipan@linux.ibm.com> Fixes: 16329364 ("perf tests: Fix record+probe_libc_inet_pton.sh without ping's debuginfo") Link: http://lkml.kernel.org/r/1561630614-3216-1-git-send-email-s1seetee@linux.vnet.ibm.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Shijith Thotton authored
[ Upstream commit c09cb129 ] The NMI handlers handle_percpu_devid_fasteoi_nmi() and handle_fasteoi_nmi() do not update the interrupt counts. Due to that the NMI interrupt count does not show up correctly in /proc/interrupts. Add the statistics and treat the NMI handlers in the same way as per cpu interrupts and prevent them from updating irq_desc::tot_count as this might be corrupted due to concurrency. [ tglx: Massaged changelog ] Fixes: 2dcf1fbc ("genirq: Provide NMI handlers") Signed-off-by:
Shijith Thotton <sthotton@marvell.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/1562313336-11888-1-git-send-email-sthotton@marvell.comSigned-off-by:
-
Josua Mayer authored
[ Upstream commit b188b032 ] Handle overlooked case where the target address is assigned to a peer and neither route nor gateway exist. For one peer, no checks are performed to see if it is meant to receive packets for a given address. As soon as there is a second peer however, checks are performed to deal with routes and gateways for handling complex setups with multiple hops to a target address. This logic assumed that no route and no gateway imply that the destination address can not be reached, which is false in case of a direct peer. Acked-by:
Jukka Rissanen <jukka.rissanen@linux.intel.com> Tested-by:
Michael Scott <mike@foundries.io> Signed-off-by:
Josua Mayer <josua.mayer@jm0.eu> Signed-off-by:
-
João Paulo Rechi Vita authored
[ Upstream commit 881cec4f ] Without the QCA ROME setup routine this adapter fails to establish a SCO connection. T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3501 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by:
-
João Paulo Rechi Vita authored
[ Upstream commit 44d34af2 ] Without the QCA ROME setup routine this adapter fails to establish a SCO connection. T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3491 Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#=0x0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#=0x1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
-
Tomas Bortoli authored
[ Upstream commit 4ce9146e ] Syzkaller found that it is possible to provoke a memory leak by never freeing rx_skb in struct bcsp_struct. Fix by freeing in bcsp_close() Signed-off-by:
Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com Signed-off-by:
-
Jian Shen authored
[ Upstream commit 2d5066fc ] For revision 0x20, the broadcast promisc is enabled by firmware, it's unnecessary to enable it when initializing VF. For revision 0x21, it's necessary to enable broadcast promisc mode when initializing or re-initializing VF, otherwise, it will be unable to send and receive promisc packets. Fixes: f01f5559 ("net: hns3: don't allow vf to enable promisc mode") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Peng Li <lipeng321@huawei.com> Signed-off-by:
-
Jiri Olsa authored
[ Upstream commit aa52bcbe ] Michael reported crash with by bpf program in json mode on powerpc: # bpftool prog -p dump jited id 14 [{ "name": "0xd00000000a9aa760", "insns": [{ "pc": "0x0", "operation": "nop", "operands": [null ] },{ "pc": "0x4", "operation": "nop", "operands": [null ] },{ "pc": "0x8", "operation": "mflr", Segmentation fault (core dumped) The code is assuming char pointers in format, which is not always true at least for powerpc. Fixing this by dumping the whole string into buffer based on its format. Please note that libopcodes code does not check return values from fprintf callback, but as per Jakub suggestion returning -1 on allocation failure so we do the best effort to propagate the error. Fixes: 107f0412 ("tools: bpftool: add JSON output for `bpftool prog dump jited *` command") Reported-by:
Michael Petlan <mpetlan@redhat.com> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Reviewed-by:
Quentin Monnet <quentin.monnet@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
Wen Yang authored
[ Upstream commit 1bcc1fd6 ] After calling of_node_put() on the codec_ep and codec_port variables, they are still being used, which may result in use-after-free. We fix this issue by calling of_node_put() after the last usage. Fixes: fce9b90c ("ASoC: audio-graph-card: cleanup DAI link loop method - step2") Signed-off-by:
Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Link: https://lore.kernel.org/r/1562229530-8121-1-git-send-email-wen.yang99@zte.com.cnSigned-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Geert Uytterhoeven authored
[ Upstream commit 3285170f ] Commit 372e722e ("gpiolib: use descriptors internally") renamed the functions to use a "gpiod" prefix, and commit 79a9becd ("gpiolib: export descriptor-based GPIO interface") introduced the "raw" variants, but both changes forgot to update the comments. Readd a similar reference to gpiod_set_value(), which was accidentally removed by commit 1e77fc82 ("gpio: Add missing open drain/source handling to gpiod_set_value_cansleep()"). Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20190701142738.25219-1-geert+renesas@glider.beSigned-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Cong Wang authored
[ Upstream commit 9d1bc24b ] bond_xmit_roundrobin() checks for IGMP packets but it parses the IP header even before checking skb->protocol. We should validate the IP header with pskb_may_pull() before using iph->protocol. Reported-and-tested-by: syzbot+e5be16aa39ad6e755391@syzkaller.appspotmail.com Fixes: a2fd940f ("bonding: fix broken multicast with round-robin mode") Cc: Jay Vosburgh <j.vosburgh@gmail.com> Cc: Veaceslav Falico <vfalico@gmail.com> Cc: Andy Gospodarek <andy@greyhouse.net> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
-
Jiri Benc authored
[ Upstream commit 11aca65e ] Selftests are reporting this failure in test_lwt_seg6local.sh: + ip netns exec ns2 ip -6 route add fb00::6 encap bpf in obj test_lwt_seg6local.o sec encap_srh dev veth2 Error fetching program/map! Failed to parse eBPF program: Operation not permitted The problem is __attribute__((always_inline)) alone is not enough to prevent clang from inserting those functions in .text. In that case, .text is not marked as relocateable. See the output of objdump -h test_lwt_seg6local.o: Idx Name Size VMA LMA File off Algn 0 .text 00003530 0000000000000000 0000000000000000 00000040 2**3 CONTENTS, ALLOC, LOAD, READONLY, CODE This causes the iproute bpf loader to fail in bpf_fetch_prog_sec: bpf_has_call_data returns true but bpf_fetch_prog_relo fails as there's no relocateable .text section in the file. To fix this, convert to 'static __always_inline'. v2: Use 'static __always_inline' instead of 'static inline __attribute__((always_inline))' Fixes: c99a84ea ("selftests/bpf: test for seg6local End.BPF action") Signed-off-by:
Jiri Benc <jbenc@redhat.com> Acked-by:
Yonghong Song <yhs@fb.com> Signed-off-by:
-
Leo Yan authored
[ Upstream commit 33bae185 ] Based on the following report from Smatch, fix the potential NULL pointer dereference check: tools/lib/bpf/libbpf.c:3493 bpf_prog_load_xattr() warn: variable dereferenced before check 'attr' (see line 3483) 3479 int bpf_prog_load_xattr(const struct bpf_prog_load_attr *attr, 3480 struct bpf_object **pobj, int *prog_fd) 3481 { 3482 struct bpf_object_open_attr open_attr = { 3483 .file = attr->file, 3484 .prog_type = attr->prog_type, ^^^^^^ 3485 }; At the head of function, it directly access 'attr' without checking if it's NULL pointer. This patch moves the values assignment after validating 'attr' and 'attr->file'. Signed-off-by:
Leo Yan <leo.yan@linaro.org> Acked-by:
-
Andrii Nakryiko authored
[ Upstream commit cdfc7f88 ] GCC8 started emitting warning about using strncpy with number of bytes exactly equal destination size, which is generally unsafe, as can lead to non-zero terminated string being copied. Use IFNAMSIZ - 1 as number of bytes to ensure name is always zero-terminated. Signed-off-by:
-
David Howells authored
[ Upstream commit 99f0eae6 ] If the rxrpc_eproto tracepoint is enabled, an oops will be cause by the trace line that rxrpc_extract_header() tries to emit when a protocol error occurs (typically because the packet is short) because the call argument is NULL. Fix this by using ?: to assume 0 as the debug_id if call is NULL. This can then be induced by: echo -e '\0\0\0\0\0\0\0\0' | ncat -4u --send-only <addr> 20001 where addr has the following program running on it: #include <stdio.h> #include <stdlib.h> #include <string.h> #include <unistd.h> #include <sys/socket.h> #include <arpa/inet.h> #include <linux/rxrpc.h> int main(void) { struct sockaddr_rxrpc srx; int fd; memset(&srx, 0, sizeof(srx)); srx.srx_family = AF_RXRPC; srx.srx_service = 0; srx.transport_type = AF_INET; srx.transport_len = sizeof(srx.transport.sin); srx.transport.sin.sin_family = AF_INET; srx.transport.sin.sin_port = htons(0x4e21); fd = socket(AF_RXRPC, SOCK_DGRAM, AF_INET6); bind(fd, (struct sockaddr *)&srx, sizeof(srx)); sleep(20); return 0; } It results in the following oops. BUG: kernel NULL pointer dereference, address: 0000000000000340 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page ... RIP: 0010:trace_event_raw_event_rxrpc_rx_eproto+0x47/0xac ... Call Trace: <IRQ> rxrpc_extract_header+0x86/0x171 ? rcu_read_lock_sched_held+0x5d/0x63 ? rxrpc_new_skb+0xd4/0x109 rxrpc_input_packet+0xef/0x14fc ? rxrpc_input_data+0x986/0x986 udp_queue_rcv_one_skb+0xbf/0x3d0 udp_unicast_rcv_skb.isra.8+0x64/0x71 ip_protocol_deliver_rcu+0xe4/0x1b4 ip_local_deliver+0xf0/0x154 __netif_receive_skb_one_core+0x50/0x6c netif_receive_skb_internal+0x26b/0x2e9 napi_gro_receive+0xf8/0x1da rtl8169_poll+0x303/0x4c4 net_rx_action+0x10e/0x333 __do_softirq+0x1a5/0x38f irq_exit+0x54/0xc4 do_IRQ+0xda/0xf8 common_interrupt+0xf/0xf </IRQ> ... ? cpuidle_enter_state+0x23c/0x34d cpuidle_enter+0x2a/0x36 do_idle+0x163/0x1ea cpu_startup_entry+0x1d/0x1f start_secondary+0x157/0x172 secondary_startup_64+0xa4/0xb0 Fixes: a25e21f0 ("rxrpc, afs: Use debug_ids rather than pointers in traces") Signed-off-by:
David Howells <dhowells@redhat.com> Reviewed-by:
Marc Dionne <marc.dionne@auristor.com> Signed-off-by:
-
Phong Tran authored
[ Upstream commit 78226f6e ] This is for fixing bug KMSAN: uninit-value in ax88772_bind Tested by https://groups.google.com/d/msg/syzkaller-bugs/aFQurGotng4/eB_HlNhhCwAJ Reported-by: syzbot+8a3fc6674bbc3978ed4e@syzkaller.appspotmail.com syzbot found the following crash on: HEAD commit: f75e4cfe kmsan: use kmsan_handle_urb() in urb.c git tree: kmsan console output: https://syzkaller.appspot.com/x/log.txt?x=136d720ea00000 kernel config: https://syzkaller.appspot.com/x/.config?x=602468164ccdc30a dashboard link: https://syzkaller.appspot.com/bug?extid=8a3fc6674bbc3978ed4e compiler: clang version 9.0.0 (/home/glider/llvm/clang 06d00afa61eef8f7f501ebdb4e8612ea43ec2d78) syz repro: https://syzkaller.appspot.com/x/repro.syz?x=12788316a00000 C reproducer: https://syzkaller.appspot.com/x/repro.c?x=120359aaa00000 ================================================================== BUG: KMSAN: uninit-value in is_valid_ether_addr include/linux/etherdevice.h:200 [inline] BUG: KMSAN: uninit-value in asix_set_netdev_dev_addr drivers/net/usb/asix_devices.c:73 [inline] BUG: KMSAN: uninit-value in ax88772_bind+0x93d/0x11e0 drivers/net/usb/asix_devices.c:724 CPU: 0 PID: 3348 Comm: kworker/0:2 Not tainted 5.1.0+ #1 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Workqueue: usb_hub_wq hub_event Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x191/0x1f0 lib/dump_stack.c:113 kmsan_report+0x130/0x2a0 mm/kmsan/kmsan.c:622 __msan_warning+0x75/0xe0 mm/kmsan/kmsan_instr.c:310 is_valid_ether_addr include/linux/etherdevice.h:200 [inline] asix_set_netdev_dev_addr drivers/net/usb/asix_devices.c:73 [inline] ax88772_bind+0x93d/0x11e0 drivers/net/usb/asix_devices.c:724 usbnet_probe+0x10f5/0x3940 drivers/net/usb/usbnet.c:1728 usb_probe_interface+0xd66/0x1320 drivers/usb/core/driver.c:361 really_probe+0xdae/0x1d80 drivers/base/dd.c:513 driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671 __device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778 bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454 __device_attach+0x454/0x730 drivers/base/dd.c:844 device_initial_probe+0x4a/0x60 drivers/base/dd.c:891 bus_probe_device+0x137/0x390 drivers/base/bus.c:514 device_add+0x288d/0x30e0 drivers/base/core.c:2106 usb_set_configuration+0x30dc/0x3750 drivers/usb/core/message.c:2027 generic_probe+0xe7/0x280 drivers/usb/core/generic.c:210 usb_probe_device+0x14c/0x200 drivers/usb/core/driver.c:266 really_probe+0xdae/0x1d80 drivers/base/dd.c:513 driver_probe_device+0x1b3/0x4f0 drivers/base/dd.c:671 __device_attach_driver+0x5b8/0x790 drivers/base/dd.c:778 bus_for_each_drv+0x28e/0x3b0 drivers/base/bus.c:454 __device_attach+0x454/0x730 drivers/base/dd.c:844 device_initial_probe+0x4a/0x60 drivers/base/dd.c:891 bus_probe_device+0x137/0x390 drivers/base/bus.c:514 device_add+0x288d/0x30e0 drivers/base/core.c:2106 usb_new_device+0x23e5/0x2ff0 drivers/usb/core/hub.c:2534 hub_port_connect drivers/usb/core/hub.c:5089 [inline] hub_port_connect_change drivers/usb/core/hub.c:5204 [inline] port_event drivers/usb/core/hub.c:5350 [inline] hub_event+0x48d1/0x7290 drivers/usb/core/hub.c:5432 process_one_work+0x1572/0x1f00 kernel/workqueue.c:2269 process_scheduled_works kernel/workqueue.c:2331 [inline] worker_thread+0x189c/0x2460 kernel/workqueue.c:2417 kthread+0x4b5/0x4f0 kernel/kthread.c:254 ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:355 Signed-off-by:
Phong Tran <tranmanphong@gmail.com> Signed-off-by:
-
Guilherme G. Piccoli authored
[ Upstream commit 3c91f25c ] Currently bnx2x ptp worker tries to read a register with timestamp information in case of TX packet timestamping and in case it fails, the routine reschedules itself indefinitely. This was reported as a kworker always at 100% of CPU usage, which was narrowed down to be bnx2x ptp_task. By following the ioctl handler, we could narrow down the problem to an NTP tool (chrony) requesting HW timestamping from bnx2x NIC with RX filter zeroed; this isn't reproducible for example with ptp4l (from linuxptp) since this tool requests a supported RX filter. It seems NIC FW timestamp mechanism cannot work well with RX_FILTER_NONE - driver's PTP filter init routine skips a register write to the adapter if there's not a supported filter request. This patch addresses the problem of bnx2x ptp thread's everlasting reschedule by retrying the register read 10 times; between the read attempts the thread sleeps for an increasing amount of time starting in 1ms to give FW some time to perform the timestamping. If it still fails after all retries, we bail out in order to prevent an unbound resource consumption from bnx2x. The patch also adds an ethtool statistic for accounting the skipped TX timestamp packets and it reduces the priority of timestamping error messages to prevent log flooding. The code was tested using both linuxptp and chrony. Reported-and-tested-by:
Przemyslaw Hausman <przemyslaw.hausman@canonical.com> Suggested-by:
Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by:
Guilherme G. Piccoli <gpiccoli@canonical.com> Acked-by:
-
Taehee Yoo authored
[ Upstream commit 7c31e54a ] __vxlan_dev_create() destroys FDB using specific pointer which indicates a fdb when error occurs. But that pointer should not be used when register_netdevice() fails because register_netdevice() internally destroys fdb when error occurs. This patch makes vxlan_fdb_create() to do not link fdb entry to vxlan dev internally. Instead, a new function vxlan_fdb_insert() is added to link fdb to vxlan dev. vxlan_fdb_insert() is called after calling register_netdevice(). This routine can avoid situation that ->ndo_uninit() destroys fdb entry in error path of register_netdevice(). Hence, error path of __vxlan_dev_create() routine can have an opportunity to destroy default fdb entry by hand. Test command ip link add bonding_masters type vxlan id 0 group 239.1.1.1 \ dev enp0s9 dstport 4789 Splat looks like: [ 213.392816] kasan: GPF could be caused by NULL-ptr deref or user memory access [ 213.401257] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 213.402178] CPU: 0 PID: 1414 Comm: ip Not tainted 5.2.0-rc5+ #256 [ 213.402178] RIP: 0010:vxlan_fdb_destroy+0x120/0x220 [vxlan] [ 213.402178] Code: df 48 8b 2b 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 06 01 00 00 4c 8b 63 08 48 b8 00 00 00 00 00 fc d [ 213.402178] RSP: 0018:ffff88810cb9f0a0 EFLAGS: 00010202 [ 213.402178] RAX: dffffc0000000000 RBX: ffff888101d4a8c8 RCX: 0000000000000000 [ 213.402178] RDX: 1bd5a00000000040 RSI: ffff888101d4a8c8 RDI: ffff888101d4a8d0 [ 213.402178] RBP: 0000000000000000 R08: fffffbfff22b72d9 R09: 0000000000000000 [ 213.402178] R10: 00000000ffffffef R11: 0000000000000000 R12: dead000000000200 [ 213.402178] R13: ffff88810cb9f1f8 R14: ffff88810efccda0 R15: ffff88810efccda0 [ 213.402178] FS: 00007f7f6621a0c0(0000) GS:ffff88811b000000(0000) knlGS:0000000000000000 [ 213.402178] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 213.402178] CR2: 000055746f0807d0 CR3: 00000001123e0000 CR4: 00000000001006f0 [ 213.402178] Call Trace: [ 213.402178] __vxlan_dev_create+0x3a9/0x7d0 [vxlan] [ 213.402178] ? vxlan_changelink+0x740/0x740 [vxlan] [ 213.402178] ? rcu_read_unlock+0x60/0x60 [vxlan] [ 213.402178] ? __kasan_kmalloc.constprop.3+0xa0/0xd0 [ 213.402178] vxlan_newlink+0x8d/0xc0 [vxlan] [ 213.402178] ? __vxlan_dev_create+0x7d0/0x7d0 [vxlan] [ 213.554119] ? __netlink_ns_capable+0xc3/0xf0 [ 213.554119] __rtnl_newlink+0xb75/0x1180 [ 213.554119] ? rtnl_link_unregister+0x230/0x230 [ ... ] Fixes: 0241b836 ("vxlan: fix default fdb entry netlink notify ordering during netdev create") Suggested-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
