Switch to using the new btcoex decision api regarding MIMO and stop
accessing the internal btcoex structs.
In case MIMO should be disabled it would detect this upon the next
Tx and force a search. The search will switch to SISO on a antenna A
which isn't used by BT.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For now, the firmware doesn't really use the field, but
it should be set to zero if there's no specific request.
Setting it to the max quota doesn't make sense.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Advertise driver's support for low priority scan.
Notice that this overwrites current setting by mac80211 which depends
only on hw scan support.
This scan priority  can be configured by user space application
and it affects scan continuity, low priority scan
will be more fragmented scan.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Bit 0 in the scan offloading flags asks the filter
to pass all the results (instead of filtering them,
by default), rather than the other way around (like
it is defined and used today).

Fix the flag name appropriately, and fix its user.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to see the content of the NVM the driver reads.
Note that the output is in binary, and requires some
external user space tool to display the data properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If we haven't loaded the D3 image yet and a failure in the suspend
process occurs, we shouldn't restart the HW, because we're still
running the D0 image.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is just a helper function to go from the mac80211
station struct to our internal one, to later allow us
to avoid temporary 'mvmsta' variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

valid_rx_ant is a bitmask of available antennas and not the number
of Rx antennas. Use num_of_ant and remove duplicate definitions
in both dvm and mvm.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

inta is checked to be zero in a IRQ_NONE branch so afterwards it
cannot be zero as it is never modified.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
[reword the patch title and fix comment]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

These devices are not sold as discrete modules but are
rather soldered down to the board.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Latest tests have shown that when BT is active and has
connections but the traffic is low, the WiFi aggregation can
be large up to 4000us without noticeable impact on BT.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add more bit field definitions used in LQ flags.
Also rename the first bit to a shorter name.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Abstract the copy_from_user() pattern into the macros defining
debugfs files, reducing the code and making adding new files
safer by avoiding having deal with copy_from_user() directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's really no reason to use void *dbgfs_data
rather than a struct iwl_mvm *mvm, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The debugfs file is getting pretty large and mixed up between
code for the hardware and code for each interface (the two
aren't even clearly separated in the code). Make it easier to
handle by splitting the per-interface code into a separate
file called debugfs-vif.c.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Just clean up the code a bit, in particular
 * make all the debugfs writes follow the same pattern
   with respect to buf/buf_size variables
 * get rid of useless comments
 * check return values of all file creations
 * drop unnecessary parentheses
 * remove an unused struct definition
 * fix some whitespace
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The HT protection flags have been a mess for a long time,
this patch fixes all this.

The proper source of information for this is the
protection in the HT operation mode IE which is
propagated to bss_conf by mac80211.

1) No need to set the HT protection flags when the link
   doesn't support HT.
2) We need to set the TGG protection when ERP is active.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Keeping connection can be useful also when testing d3
using the debugfs file (d3_test).

Save the vif to keep connection on, and consider it
when iterating over the interfaces.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Re-initialize rs when we get a rate_update hook called which
happens when remote STA changes bandwidth or sends a VHT opmode
notification.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When waking up from d3 due to disconnection event
(e.g. because of beacon loss), we should disconnect
immediately.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Even if d3_test_pme_ptr is not available, d3_test can still
be useful, e.g. by manually triggering resume (with ctrl-c),
and reading the wakeup reasons.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor setting of VHT enabled rates in preparation of adding
some more logic there.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove the flags parameter which should be set to sync or async
according to whether this is called during sta init or not.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Info about VHT/HT rates wasn't printed properly when dumping
the rate scale table. Fix that and print more info. While at it
fix some other minor issues in the printing and prevent
overflowing the print buffer.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

After wait_event_timeout(), the condition must still be
true if it returns >0, in fact almost the last thing in
it is checking the condition again. It's therefore not
useful to check yet again in our code, clean it up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Writting to fw_nmi entry will set DEVICE_SET_NMI_REG (0x00a01c30)
generating NMI that halts NIC CPU.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The transport layer doesn't need to know the TX_CMD id.
It can be set by the op_mode.
The transport layer still needs to know the layout of the
Tx command because of alignment issues and because of the
scratch pointer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Conflicts:
	drivers/net/wireless/brcm80211/Kconfig
	net/mac80211/util.c

As it stands dynamic user regulatory domain support is
only possible for a few programmed regulatory domains as
a few countries do not allow for this.

The existing code however only would take advantage of
the feature if a custom world regulatory domain is used
though as that's when we clear beconing flags. We need
to lift this restriction as otherwise this feature is
pointless.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will be used later.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This will be used later.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

freq_reg_info() expects KHz and not MHz, fix this. In
this case we'll now be getting the no-ir flags cleared
on channels for any channel when the country IE trusts
that channel.

@@
struct ieee80211_channel *ch;
struct wiphy *wiphy;
const struct ieee80211_reg_rule *rule;
@@

-rule = freq_reg_info(wiphy, ch->center_freq);
+rule = freq_reg_info(wiphy, MHZ_TO_KHZ(ch->center_freq));

Generated-by: Coccinelle SmPL
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Peter Senna Tschudin <peter.senna@gmail.com>
Reported-by: Mihir Shete <smihir@qti.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While at it convert this into a switch statement, this
makes it easier and manage.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Simplify ath_reg_apply_beaconing_flags() by making use of
thew new no-ir helper.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This also applies the no-ibss flag to the channels or clears it.
The idea here is to clarify no initiated radiation should be
allowed on these channels.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The routine ath_reg_apply_active_scan_flags() can be a bit
hard to read, this cleans it up by adding helpers for the
two cases of clearing IR flags or adding them. This approach
also makes no assumptions on the index of channels 12 and 13
so it should be portable accross different drivers.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The existing logic removes the passive scan flag from
channels 12 and 13 when a regulatory hint coming from
something other than a country IE has been passed. This
is incorrect, the original intention was to ensure we
always have passive scan enabled for these two channels
for a specific set of custom world regulatory domains.

Cc: smihir@qti.qualcomm.com
Cc: tushnimb@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Stable <stable@vger.kernel.org> [3.10+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>