- 22 Jul, 2015 40 commits
-
-
Pali Rohár authored
commit b8830a4e upstream. This commit fix kernel crash when probing for rfkill devices in dell-laptop driver failed. Function free_page() was incorrectly used on struct page * instead of virtual address of SMI buffer. This commit also simplify allocating page for SMI buffer by using __get_free_page() function instead of sequential call of functions alloc_page() and page_address(). Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Acked-by:
Michal Hocko <mhocko@suse.cz> Signed-off-by:
Darren Hart <dvhart@linux.intel.com> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Vineet Gupta authored
commit d57f7272 upstream. When auditing cmpxchg call sites, Chuck noted that gcc was optimizing away some of the desired LDs. | do { | new = old = *ipi_data_ptr; | new |= 1U << msg; | } while (cmpxchg(ipi_data_ptr, old, new) != old); was generating to below | 8015cef8: ld r2,[r4,0] <-- First LD | 8015cefc: bset r1,r2,r1 | | 8015cf00: llock r3,[r4] <-- atomic op | 8015cf04: brne r3,r2,8015cf10 | 8015cf08: scond r1,[r4] | 8015cf0c: bnz 8015cf00 | | 8015cf10: brne r3,r2,8015cf00 <-- Branch doesn't go to orig LD Although this was fixed by adding a ACCESS_ONCE in this call site, it seems safer (for now at least) to add compiler barrier to LLSC based cmpxchg Reported-by:
Chuck Jordan <cjordan@synopsys,com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Takashi Iwai authored
commit fff3b16d upstream. Many harddisks (mostly WD ones) have firmware problems and take too long, more than 10 seconds, to resume from suspend. And this often exceeds the default DPM watchdog timeout (12 seconds), resulting in a kernel panic out of sudden. Since most distros just take the default as is, we should give a bit more safer value. This patch increases the default value from 12 seconds to one minute, which has been confirmed to be long enough for such problematic disks. Link: https://bugzilla.kernel.org/show_bug.cgi?id=91921 Fixes: 70fea60d (PM / Sleep: Detect device suspend/resume lockup and log event) Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Dan Carpenter authored
commit 7bc10388 upstream. There is a small memory leak on error. Fixes: 0f1b414d (ACPI / PNP: Avoid conflicting resource reservations) Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Jan Kara authored
commit 2426f391 upstream. file_remove_suid() could mistakenly set S_NOSEC inode bit when root was modifying the file. As a result following writes to the file by ordinary user would avoid clearing suid or sgid bits. Fix the bug by checking actual mode bits before setting S_NOSEC. Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Eric W. Biederman authored
commit 8405a8ff upstream. Add code to nf_unregister_hook to flush the nf_queue when a hook is unregistered. This guarantees that the pointer that the nf_queue code retains into the nf_hook list will remain valid while a packet is queued. I tested what would happen if we do not flush queued packets and was trivially able to obtain the oops below. All that was required was to stop the nf_queue listening process, to delete all of the nf_tables, and to awaken the nf_queue listening process. > BUG: unable to handle kernel paging request at 0000000100000001 > IP: [<0000000100000001>] 0x100000001 > PGD b9c35067 PUD 0 > Oops: 0010 [#1] SMP > Modules linked in: > CPU: 0 PID: 519 Comm: lt-nfqnl_test Not tainted > task: ffff8800b9c8c050 ti: ffff8800ba9d8000 task.ti: ffff8800ba9d8000 > RIP: 0010:[<0000000100000001>] [<0000000100000001>] 0x100000001 > RSP: 0018:ffff8800ba9dba40 EFLAGS: 00010a16 > RAX: ffff8800bab48a00 RBX: ffff8800ba9dba90 RCX: ffff8800ba9dba90 > RDX: ffff8800b9c10128 RSI: ffff8800ba940900 RDI: ffff8800bab48a00 > RBP: ffff8800b9c10128 R08: ffffffff82976660 R09: ffff8800ba9dbb28 > R10: dead000000100100 R11: dead000000200200 R12: ffff8800ba940900 > R13: ffffffff8313fd50 R14: ffff8800b9c95200 R15: 0000000000000000 > FS: 00007fb91fc34700(0000) GS:ffff8800bfa00000(0000) knlGS:0000000000000000 > CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > CR2: 0000000100000001 CR3: 00000000babfb000 CR4: 00000000000007f0 > Stack: > ffffffff8206ab0f ffffffff82982240 ffff8800bab48a00 ffff8800b9c100a8 > ffff8800b9c10100 0000000000000001 ffff8800ba940900 ffff8800b9c10128 > ffffffff8206bd65 ffff8800bfb0d5e0 ffff8800bab48a00 0000000000014dc0 > Call Trace: > [<ffffffff8206ab0f>] ? nf_iterate+0x4f/0xa0 > [<ffffffff8206bd65>] ? nf_reinject+0x125/0x190 > [<ffffffff8206dee5>] ? nfqnl_recv_verdict+0x255/0x360 > [<ffffffff81386290>] ? nla_parse+0x80/0xf0 > [<ffffffff8206c42c>] ? nfnetlink_rcv_msg+0x13c/0x240 > [<ffffffff811b2fec>] ? __memcg_kmem_get_cache+0x4c/0x150 > [<ffffffff8206c2f0>] ? nfnl_lock+0x20/0x20 > [<ffffffff82068159>] ? netlink_rcv_skb+0xa9/0xc0 > [<ffffffff820677bf>] ? netlink_unicast+0x12f/0x1c0 > [<ffffffff82067ade>] ? netlink_sendmsg+0x28e/0x650 > [<ffffffff81fdd814>] ? sock_sendmsg+0x44/0x50 > [<ffffffff81fde07b>] ? ___sys_sendmsg+0x2ab/0x2c0 > [<ffffffff810e8f73>] ? __wake_up+0x43/0x70 > [<ffffffff8141a134>] ? tty_write+0x1c4/0x2a0 > [<ffffffff81fde9f4>] ? __sys_sendmsg+0x44/0x80 > [<ffffffff823ff8d7>] ? system_call_fastpath+0x12/0x6a > Code: Bad RIP value. > RIP [<0000000100000001>] 0x100000001 > RSP <ffff8800ba9dba40> > CR2: 0000000100000001 > ---[ end trace 08eb65d42362793f ]--- Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Ralf Baechle authored
commit d496f784 upstream. A ROSE socket doesn't necessarily always have a neighbour pointer so check if the neighbour pointer is valid before dereferencing it. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Tested-by:
Bernard Pidoux <f6bvp@free.fr> Signed-off-by:
-
Darrick J. Wong authored
commit 292db1bc upstream. ext4 isn't willing to map clusters to a non-extent file. Don't signal this with an out of space error, since the FS will retry the allocation (which didn't fail) forever. Instead, return EUCLEAN so that the operation will fail immediately all the way back to userspace. (The fix is either to run e2fsck -E bmap2extent, or to chattr +e the file.) Signed-off-by:
Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
-
Eric Sandeen authored
commit 2ac56d3d upstream. If we create a CRC filesystem, mount it, and create a symlink with a path long enough that it can't live in the inode, we get a very strange result upon remount: # ls -l mnt total 4 lrwxrwxrwx. 1 root root 929 Jun 15 16:58 link -> XSLM XSLM is the V5 symlink block header magic (which happens to be followed by a NUL, so the string looks terminated). xfs_readlink_bmap() advanced cur_chunk by the size of the header for CRC filesystems, but never actually used that pointer; it kept reading from bp->b_addr, which is the start of the block, rather than the start of the symlink data after the header. Looks like this problem goes back to v3.10. Fixing this gets us reading the proper link target, again. Signed-off-by:
Eric Sandeen <sandeen@redhat.com> Reviewed-by:
Dave Chinner <dchinner@redhat.com> Signed-off-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
James Hogan authored
commit 8e748c8d upstream. KVM guest kernels for trap & emulate run in user mode, with a modified set of kernel memory segments. However the fixmap address is still in the normal KSeg3 region at 0xfffe0000 regardless, causing problems when cache alias handling makes use of them when handling copy on write. Therefore define FIXADDR_TOP as 0x7ffe0000 in the guest kernel mapped region when CONFIG_KVM_GUEST is defined. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/9887/Signed-off-by:
-
Theodore Ts'o authored
commit 89d96a6f upstream. Normally all of the buffers will have been forced out to disk before we call invalidate_bdev(), but there will be some cases, where a file system operation was aborted due to an ext4_error(), where there may still be some dirty buffers in the buffer cache for the device. So try to force them out to memory before calling invalidate_bdev(). This fixes a warning triggered by generic/081: WARNING: CPU: 1 PID: 3473 at /usr/projects/linux/ext4/fs/block_dev.c:56 __blkdev_put+0xb5/0x16f() Signed-off-by:
-
Joerg Roedel authored
commit 0b3fff54 upstream. Make sure that we are skipping over large PTEs while walking the page-table tree. Fixes: 5c34c403 ("iommu/amd: Fix memory leak in free_pagetable") Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Will Deacon authored
commit 6f1a6ae8 upstream. When building the kernel with a bare-metal (ELF) toolchain, the -shared option may not be passed down to collect2, resulting in silent corruption of the vDSO image (in particular, the DYNAMIC section is omitted). The effect of this corruption is that the dynamic linker fails to find the vDSO symbols and libc is instead used for the syscalls that we intended to optimise (e.g. gettimeofday). Functionally, there is no issue as the sigreturn trampoline is still intact and located by the kernel. This patch fixes the problem by explicitly passing -shared to the linker when building the vDSO. Reported-by:
Szabolcs Nagy <Szabolcs.Nagy@arm.com> Reported-by:
James Greenlaigh <james.greenhalgh@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Martin K. Petersen authored
commit 243918be upstream. Queued TRIM got disabled on Micron M500DC drives thanks to the "Micron_M500*" pattern we had in place to accommodate the previous generation of this drive family. Tweak the blacklist entry slightly so we only disable queued TRIM for the non-DC variants of M500 drives. Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Dmitry Tunin authored
commit 7e730c7f upstream. BugLink: https://bugs.launchpad.net/bugs/1394368 This device requires new firmware files AthrBT_0x11020100.dfu and ramps_0x11020100_40.dfu added to /lib/firmware/ar3k/ that are not included in linux-firmware yet. T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 5 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300d Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Dmitry Tunin authored
commit ec0810d2 upstream. BugLink: https://bugs.launchpad.net/bugs/1449730 T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300f Rev=00.01 C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Signed-off-by:
-
Sujith Manoharan authored
commit bd0fca1b upstream. T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=04ca ProdID=300b Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Reported-by:
Face <falazemi@gmail.com> Signed-off-by:
Sujith Manoharan <sujith@msujith.org> Signed-off-by:
-
Rafael J. Wysocki authored
commit 0f1b414d upstream. Commit b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" overlooked the fact that the memory and/or I/O regions reserved by acpi_reserve_resources() may conflict with those reserved by the PNP "system" driver. If that conflict actually takes place, it causes the reservations made by the "system" driver to fail while before commit b9a5e5e1 all reservations made by it and by acpi_reserve_resources() would be successful. In turn, that allows the resources that haven't been reserved by the "system" driver to be used by others (e.g. PCI) which sometimes leads to functional problems (up to and including boot failures). To fix that issue, introduce a common resource reservation routine, acpi_reserve_region(), to be used by both acpi_reserve_resources() and the "system" driver, that will track all resources reserved by it and avoid making conflicting requests. Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831 Link: http://marc.info/?t=143389402600001&r=1&w=2 Fixes: b9a5e5e1 "ACPI / init: Fix the ordering of acpi_reserve_resources()" Reported-by:
Roland Dreier <roland@purestorage.com> Signed-off-by:
-
Mikulas Patocka authored
commit dd4c1b7d upstream. If the number_of_areas argument was zero the kernel would crash on div-by-zero. Add better input validation. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit 6096d91a upstream. The metadata space map has a simplified 'bootstrap' mode that is operational when extending the space maps. Whilst in this mode it's possible for some refcount decrement operations to become queued (eg, as a result of shadowing one of the bitmap indexes). These decrements were not being applied when switching out of bootstrap mode. The effect of this bug was the leaking of a 4k metadata block. This is detected by the latest version of thin_check as a non fatal error. Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Dave P Martin authored
commit b9bcc919 upstream. The memmap freeing code in free_unused_memmap() computes the end of each memblock by adding the memblock size onto the base. However, if SPARSEMEM is enabled then the value (start) used for the base may already have been rounded downwards to work out which memmap entries to free after the previous memblock. This may cause memmap entries that are in use to get freed. In general, you're not likely to hit this problem unless there are at least 2 memblocks and one of them is not aligned to a sparsemem section boundary. Note that carve-outs can increase the number of memblocks by splitting the regions listed in the device tree. This problem doesn't occur with SPARSEMEM_VMEMMAP, because the vmemmap code deals with freeing the unused regions of the memmap instead of requiring the arch code to do it. This patch gets the memblock base out of the memblock directly when computing the block end address to ensure the correct value is used. Signed-off-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
-
Alexander Sverdlin authored
commit 0a8237ae upstream. pca9541 and pca954x are calling master_xfer() of the parent adapter directly thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead. Signed-off-by:
Alexander Sverdlin <alexander.sverdlin@nokia.com> Tested-by:
Łukasz Gemborowski <lukasz.gemborowski@nokia.com> Acked-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Jisheng Zhang <jszhang@marvell.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Fixes: b7f62584 ("i2c: add quirk checks to core") Signed-off-by:
-
Alexander Sverdlin authored
commit e766f338 upstream. Newly introduced quirks infrastructure doesn't work for the devices behind MUXes because MUX's master_xfer() calls parent's master_xfer() directly without checking the quirks. Instead of duplicating check code in MUX just call __i2c_transfer() instead. This has a side effect on tracing (messages will appear on both MUX bus and parent bus), but maybe that's not bad at the end. Signed-off-by:
-
Marc Zyngier authored
commit 85e84ba3 upstream. On VM entry, we disable access to the VFP registers in order to perform a lazy save/restore of these registers. On VM exit, we restore access, test if we did enable them before, and save/restore the guest/host registers if necessary. In this sequence, the FPEXC register is always accessed, irrespective of the trapping configuration. If the guest didn't touch the VFP registers, then the HCPTR access has now enabled such access, but we're missing a barrier to ensure architectural execution of the new HCPTR configuration. If the HCPTR access has been delayed/reordered, the subsequent access to FPEXC will cause a trap, which we aren't prepared to handle at all. The same condition exists when trapping to enable VFP for the guest. The fix is to introduce a barrier after enabling VFP access. In the vmexit case, it can be relaxed to only takes place if the guest hasn't accessed its view of the VFP registers, making the access to FPEXC safe. The set_hcptr macro is modified to deal with both vmenter/vmexit and vmtrap operations, and now takes an optional label that is branched to when the guest hasn't touched the VFP registers. Reported-by:
Vikram Sethi <vikrams@codeaurora.org> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Hon Ching \\(Vicky\\) Lo authored
commit 9d75f089 upstream. tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq, the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address. Signed-off-by:
Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by:
Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by:
Ashley Lai <ashley@ahsleylai.com> Fixes: 132f7629 ("drivers/char/tpm: Add new device driver to support IBM vTPM") Signed-off-by:
Peter Huewe <peterhuewe@gmx.de> Signed-off-by:
-
Jeff Layton authored
commit 764ad8ba upstream. The current buffer is much too small if you have a relatively long hostname. Bring it up to the size of the one that SETCLIENTID has. Reported-by:
Michael Skralivetsky <michael.skralivetsky@primarydata.com> Signed-off-by:
Jeff Layton <jeff.layton@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Mimi Zohar authored
commit 45b26133 upstream. This patch fixes a bug introduced in "4d7aeee ima: define new template ima-ng and template fields d-ng and n-ng". Changelog: - change int to uint32 (Roberto Sassu's suggestion) Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
Roberto Sassu <rsassu@suse.de> Signed-off-by:
-
Maxime Coquelin authored
commit 921cc294 upstream. The way the mask is generated in regmap_field_init() is wrong. Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift overflow while calculating the mask field. On some 32 bits architectures, such as x86, the generated mask is 0, instead of the expected 0xffffffff. This patch uses GENMASK() to fix the problem, as this macro is already safe regarding shift overflow. Signed-off-by:
Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Arnd Bergmann authored
commit 4b200b46 upstream. This fixes a several year old regression that I found while trying to get the Yoga 3 11 to work. The ideapad_rfk_set function is meant to send a command to the embedded controller through ACPI, but as of c1f73658, it sends the index of the rfkill device instead of the command, and ignores the opcode field. This changes it back to the original behavior, which indeed flips the rfkill state as seen in the debugfs interface. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: c1f73658 ("ideapad: pass ideapad_priv as argument (part 2)") Signed-off-by:
-
Joseph Qi authored
commit 6f6a6fda upstream. If updating journal superblock fails after journal data has been flushed, the error is omitted and this will mislead the caller as a normal case. In ocfs2, the checkpoint will be treated successfully and the other node can get the lock to update. Since the sb_start is still pointing to the old log block, it will rewrite the journal data during journal recovery by the other node. Thus the new updates will be overwritten and ocfs2 corrupts. So in above case we have to return the error, and ocfs2_commit_cache will take care of the error and prevent the other node to do update first. And only after recovering journal it can do the new updates. The issue discussion mail can be found at: https://oss.oracle.com/pipermail/ocfs2-devel/2015-June/010856.html http://comments.gmane.org/gmane.comp.file-systems.ext4/48841 [ Fixed bug in patch which allowed a non-negative error return from jbd2_cleanup_journal_tail() to leak out of jbd2_fjournal_flush(); this was causing xfstests ext4/306 to fail. -- Ted ] Reported-by:
Yiwen Jiang <jiangyiwen@huawei.com> Signed-off-by:
Joseph Qi <joseph.qi@huawei.com> Signed-off-by:
-
Arun Chandran authored
commit 15b8d2c4 upstream. In big endian mode regmap_bulk_read gives incorrect data for byte reads. This is because memcpy of a single byte from an address after full word read gives different results when endianness differs. ie. we get little-end in LE and big-end in BE. Signed-off-by:
Arun Chandran <achandran@mvista.com> Signed-off-by:
-
Dmitry Monakhov authored
commit b4f1afcd upstream. jbd2_cleanup_journal_tail() can be invoked by jbd2__journal_start() So allocations should be done with GFP_NOFS [Full stack trace snipped from 3.10-rh7] [<ffffffff815c4bd4>] dump_stack+0x19/0x1b [<ffffffff8105dba1>] warn_slowpath_common+0x61/0x80 [<ffffffff8105dcca>] warn_slowpath_null+0x1a/0x20 [<ffffffff815c2142>] slab_pre_alloc_hook.isra.31.part.32+0x15/0x17 [<ffffffff8119c045>] kmem_cache_alloc+0x55/0x210 [<ffffffff811477f5>] ? mempool_alloc_slab+0x15/0x20 [<ffffffff811477f5>] mempool_alloc_slab+0x15/0x20 [<ffffffff81147939>] mempool_alloc+0x69/0x170 [<ffffffff815cb69e>] ? _raw_spin_unlock_irq+0xe/0x20 [<ffffffff8109160d>] ? finish_task_switch+0x5d/0x150 [<ffffffff811f1a8e>] bio_alloc_bioset+0x1be/0x2e0 [<ffffffff8127ee49>] blkdev_issue_flush+0x99/0x120 [<ffffffffa019a733>] jbd2_cleanup_journal_tail+0x93/0xa0 [jbd2] -->GFP_KERNEL [<ffffffffa019aca1>] jbd2_log_do_checkpoint+0x221/0x4a0 [jbd2] [<ffffffffa019afc7>] __jbd2_log_wait_for_space+0xa7/0x1e0 [jbd2] [<ffffffffa01952d8>] start_this_handle+0x2d8/0x550 [jbd2] [<ffffffff811b02a9>] ? __memcg_kmem_put_cache+0x29/0x30 [<ffffffff8119c120>] ? kmem_cache_alloc+0x130/0x210 [<ffffffffa019573a>] jbd2__journal_start+0xba/0x190 [jbd2] [<ffffffff811532ce>] ? lru_cache_add+0xe/0x10 [<ffffffffa01c9549>] ? ext4_da_write_begin+0xf9/0x330 [ext4] [<ffffffffa01f2c77>] __ext4_journal_start_sb+0x77/0x160 [ext4] [<ffffffffa01c9549>] ext4_da_write_begin+0xf9/0x330 [ext4] [<ffffffff811446ec>] generic_file_buffered_write_iter+0x10c/0x270 [<ffffffff81146918>] __generic_file_write_iter+0x178/0x390 [<ffffffff81146c6b>] __generic_file_aio_write+0x8b/0xb0 [<ffffffff81146ced>] generic_file_aio_write+0x5d/0xc0 [<ffffffffa01bf289>] ext4_file_write+0xa9/0x450 [ext4] [<ffffffff811c31d9>] ? pipe_read+0x379/0x4f0 [<ffffffff811b93f0>] do_sync_write+0x90/0xe0 [<ffffffff811b9b6d>] vfs_write+0xbd/0x1e0 [<ffffffff811ba5b8>] SyS_write+0x58/0xb0 [<ffffffff815d4799>] system_call_fastpath+0x16/0x1b Signed-off-by:
Dmitry Monakhov <dmonakhov@openvz.org> Signed-off-by:
-
Ryan Underwood authored
commit 2fb22a80 upstream. Disable write buffering on the Toshiba ToPIC95 if it is enabled by somebody (it is not supposed to be a power-on default according to the datasheet). On the ToPIC95, practically no 32-bit Cardbus card will work under heavy load without locking up the whole system if this is left enabled. I tried about a dozen. It does not affect 16-bit cards. This is similar to the O2 bugs in early controller revisions it seems. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961Signed-off-by:
Ryan C. Underwood <nemesis@icequake.net> Signed-off-by:
Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by:
-
Theodore Ts'o authored
commit bdf96838 upstream. The commit cf108bca: "ext4: Invert the locking order of page_lock and transaction start" caused __ext4_journalled_writepage() to drop the page lock before the page was written back, as part of changing the locking order to jbd2_journal_start -> page_lock. However, this introduced a potential race if there was a truncate racing with the data=journalled writeback mode. Fix this by grabbing the page lock after starting the journal handle, and then checking to see if page had gotten truncated out from under us. This fixes a number of different warnings or BUG_ON's when running xfstests generic/086 in data=journalled mode, including: jbd2_journal_dirty_metadata: vdc-8: bad jh for block 115643: transaction (ee3fe7 c0, 164), jh->b_transaction ( (null), 0), jh->b_next_transaction ( (null), 0), jlist 0 - and - kernel BUG at /usr/projects/linux/ext4/fs/jbd2/transaction.c:2200! ... Call Trace: [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c02b2de5>] __ext4_journalled_invalidatepage+0x10f/0x117 [<c02b2ded>] ? __ext4_journalled_invalidatepage+0x117/0x117 [<c027d883>] ? lock_buffer+0x36/0x36 [<c02b2dfa>] ext4_journalled_invalidatepage+0xd/0x22 [<c0229139>] do_invalidatepage+0x22/0x26 [<c0229198>] truncate_inode_page+0x5b/0x85 [<c022934b>] truncate_inode_pages_range+0x156/0x38c [<c0229592>] truncate_inode_pages+0x11/0x15 [<c022962d>] truncate_pagecache+0x55/0x71 [<c02b913b>] ext4_setattr+0x4a9/0x560 [<c01ca542>] ? current_kernel_time+0x10/0x44 [<c026c4d8>] notify_change+0x1c7/0x2be [<c0256a00>] do_truncate+0x65/0x85 [<c0226f31>] ? file_ra_state_init+0x12/0x29 - and - WARNING: CPU: 1 PID: 1331 at /usr/projects/linux/ext4/fs/jbd2/transaction.c:1396 irty_metadata+0x14a/0x1ae() ... Call Trace: [<c01b879f>] ? console_unlock+0x3a1/0x3ce [<c082cbb4>] dump_stack+0x48/0x60 [<c0178b65>] warn_slowpath_common+0x89/0xa0 [<c02ef2cf>] ? jbd2_journal_dirty_metadata+0x14a/0x1ae [<c0178bef>] warn_slowpath_null+0x14/0x18 [<c02ef2cf>] jbd2_journal_dirty_metadata+0x14a/0x1ae [<c02d8615>] __ext4_handle_dirty_metadata+0xd4/0x19d [<c02b2f44>] write_end_fn+0x40/0x53 [<c02b4a16>] ext4_walk_page_buffers+0x4e/0x6a [<c02b59e7>] ext4_writepage+0x354/0x3b8 [<c02b2f04>] ? mpage_release_unused_pages+0xd4/0xd4 [<c02b1b21>] ? wait_on_buffer+0x2c/0x2c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b5a5b>] __writepage+0x10/0x2e [<c0225956>] write_cache_pages+0x22d/0x32c [<c02b5a4b>] ? ext4_writepage+0x3b8/0x3b8 [<c02b6ee8>] ext4_writepages+0x102/0x607 [<c019adfe>] ? sched_clock_local+0x10/0x10e [<c01a8a7c>] ? __lock_is_held+0x2e/0x44 [<c01a8ad5>] ? lock_is_held+0x43/0x51 [<c0226dff>] do_writepages+0x1c/0x29 [<c0276bed>] __writeback_single_inode+0xc3/0x545 [<c0277c07>] writeback_sb_inodes+0x21f/0x36d ... Signed-off-by:
-
Catalin Marinas authored
commit 565630d5 upstream. After secondary CPU boot or hotplug, the active_mm of the idle thread is &init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1 and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the TTBR0_EL1 is already set to the reserved value, there is no need to perform any context reset. Signed-off-by:
-
Zidan Wang authored
commit a077e81e upstream. the enum of "DAC Polarity" should be wm8960_enum[1]. Signed-off-by:
Zidan Wang <zidan.wang@freescale.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Lior Amsalem authored
commit 9136291f upstream. This patch fixes a bug in the XOR driver where the cleanup function can be called and free descriptors that never been processed by the engine (which result in data errors). The cleanup function will free descriptors based on the ownership bit in the descriptors. Fixes: ff7b0479 ("dmaengine: DMA engine driver for Marvell XOR engine") Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by:
Ofer Heifetz <oferh@marvell.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Cyrille Pitchen authored
commit 93563a6a upstream. For TX transactions, the TXCOMP bit in the Status Register is cleared when the first data is written into the Transmit Holding Register. In the lines from at91_do_twi_transfer(): at91_twi_write_data_dma(dev); at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP); the TXCOMP interrupt may be enabled before the DMA controller has actually started to write into the THR. In such a case, the TXCOMP bit is still set into the Status Register so the interrupt is triggered immediately. The driver understands that a transaction completion has occurred but this transaction hasn't started yet. Hence the TXCOMP interrupt is no longer enabled by at91_do_twi_transfer() but instead by at91_twi_write_data_dma_callback(). Also, the TXCOMP bit in the Status Register in not a clear on read flag but a snapshot of the transmission state at the time the Status Register is read. When a NACK error is dectected by the I2C controller, the TXCOMP, NACK and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP interrupt is triggered at the same time. Also setting the TXRDY to 1 triggers the DMA controller to write the next data into the THR. Such a write resets the TXCOMP bit to 0 in the SR. So depending on when the interrupt handler reads the SR, it may fail to detect the NACK error if it relies on the TXCOMP bit. The NACK bit and its interrupt should be used instead. For RX transactions, the TXCOMP bit in the Status Register is cleared when the START bit is set into the Control Register. However to unify the management of the TXCOMP bit when the DMA controller is used, the TXCOMP interrupt is now enabled by the DMA callbacks for both TX and RX transfers. Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
-
Thomas Petazzoni authored
commit ea78b951 upstream. There was a mistake in the definition of the functions for MPP48 on Marvell Armada XP. The second function is dev(clkout), and not tclk. Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 463e270f ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Thomas Petazzoni authored
commit 80b3d04f upstream. The latest version of the Armada XP datasheet no longer documents the VDD cpu_pd functions, which might indicate they are not working and/or not supported. This commit ensures the pinctrl driver matches the datasheet. Signed-off-by:
-
