Remove it, as it indirectly exposes netdev features. It's not used in
iproute2 (2.6.38) - is anything else using its interface?
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The same information and more can be obtained by using ethtool
with ETHTOOL_GFEATURES.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not used anywhere except net/core/dev.c now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan_features contains features inherited from underlying device.
NETIF_SOFT_FEATURES are not inherited but belong to the vlan device
itself (ensured in vlan_dev_fix_features()).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the fact that ORing with zero is a no-op.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove wrong setting of dev->flags. NETIF_F_NO_CSUM maps to IFF_DEBUG
there, so looks like a mistake.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.

For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Only 8111b needs to enable rx when shutdowning with WoL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Only 8111E needs enable RxConfig bit 0 ~ 3 when suspending or
shutdowning for wake on lan.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Add the ERI functions which would be used by the new chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

- Disable tx and rx by resetting hw, so replace rtl8169_asic_down
  with rtl8169_hw_reset.
- RxConfig bits 0 ~ 5 have to be cleared before hw reset to avoid
  receiving spurious data.
- Certain chips need to do some checking before reset.
- Remove hw reset which is done before hw_start. It is done in close,
  down or device probe functions.
- Move rtl8169_init_ring_indexes function into rtl_hw_reset function.
  The indexes of tx and rx only need to be zero when the hw resets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Define new registers and modify some existing ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>

Reset card->tx_dma_progress when lv1_net_start_tx_dma() fails or it
won't send anything afterwards anymore
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert to a proper state when gelic_card_kick_txdma() fails:
- Don't trigger BUG_ON when releasing the unsent tx descriptor
- Reset the tx chain head since the tail was not modified and
  hence not in sync
- Unlink the released descriptor bus address from its predecessor
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Change FW dump capture mask to a defult value, instead of using the recommended
  value from the FW. This was done to keep the capture mask consistent with other
  function drivers.

o Update driver version to 5.0.21
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o Defined error code such as fw not responding, test already running and
  cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.

Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

to allow iSCSI connection to fail faster instead of waiting for the
long timeout.

Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data.  The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.

The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the driver state (and power source) is being more intensely
scrutinized, we need to make sure it is correct 100% of the time.  This
patch finds and fixes all dangling power state transitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds code to update the status of the function to a common
location to the critical section added in the previous patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code that performs the power source switching will need to consider
the status of the other devices before making any switches.  The status
updates and power source switching will need to be an atomic operation,
so a critical section will be needed.  This patch establishes the
critical section through a CPMU mutex.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tg3 devices will need to know exactly what function number they are so
that they can communicate their status to the other functions.  In a KVM
environment, the function number of a device presented by the kernel
might not be the true function number, so an alternative method to
determine the function number is needed.

This patch used to contain an implementation for the alternative method,
but recently we discovered a hardware bug that renders it incorrect.
While new method is not yet known, it is still useful to consolidate the
code that determines the PCI function to one location and use the
results throughout the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently pci_set_power_state() does not return useful return codes for
transitions to the D0 power state.  If a device refuses to go into D0,
the PCI layer issues a warning but returns success.

Entering into D0 is a requirement for correct operation of tg3 devices
though.  If the PCI layer should be changed to return an error code for
this type of failure, the tg3 driver would be interested in catching it
and reacting to it.  This patch makes the necessary modifications.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tg3 driver is going to require memory mapped register access much
sooner than before.  This patch makes sure the device is in the D0 power
state as soon as possible, and moves the code that enables the memory
arbiter outside tg3_get_eeprom_hw_cfg() where it can be more easily
monitored.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following patch will require the driver to communicate with the APE
much sooner than before.  This patch make sure the APE registers are
memory mapped and that the ENABLE_APE bit is set before the first use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we flush tp_status and then flush the remainder of the header+payload.
tp_status should be flushed in the end to avoid stale data being read by user-space.

Incorrectly re-ordered barriers in v1.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	net/bluetooth/l2cap_core.c

Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:

1) dynamic allocation
2) attachment to dst->hh
3) refcounting

Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>