- 15 Jan, 2015 6 commits
-
-
Vladimir Kondratiev authored
Upon Tx vring creation, initiate BACK establishment with maximum possible window size. When establishing secure connection, there is EAPOL data exchange between connection itself and "data port open", where security is done and non-EAPOL data may be transferred. It is better to send EAPOL frames using normal ACK because of firmware considerations. send ADDBA only is 2 conditions met: - data port open for the corresponded STA - vring created Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Vladimir Kondratiev authored
Introduce BACK establishment procedures; decision logic is not implemented yet; debugfs entry 'addba' used to manually trigger addba/delba for ringid 0. debugfs usage: to establish BACK with agg_wsize 16: echo 16 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba to delete BACK: echo 0 > /sys/kernel/debug/ieee80211/phy0/wil6210/addba to change agg_wsize, one need to delete BACK and establish it anew ADDBA flow for: - originator Tx side (initiator) sends WMI_VRING_BA_EN_CMDID providing agg_wsize and timeout parameters. Eventually, it gets event confirming BACK agreement - WMI_BA_STATUS_EVENTID with negotiated parameters. On this event, update Tx vring data (struct vring_tx_data) and display BACK parameters on debugfs - recipient Rx side (recipient) firmware informs driver about ADDBA with WMI_RCP_ADDBA_REQ_EVENTID, driver process it in service work queue wq_service. It adjusts parameters and sends response with WMI_RCP_ADDBA_RESP_CMDID, and final confirmation provided by firmware with WMI_ADDBA_RESP_SENT_EVENTID. In case of success, driver updates Rx BACK reorder buffer. policy for BACK parameters: - aggregation size (agg_wsize * MPDUsize)) to not exceed 64Kbytes DELBA flow for: - originator driver decides to terminate BACK, it sends WMI_VRING_BA_DIS_CMDID and updates struct vring_tx_data associated with vring; ignore WMI_DELBA_EVENTID. - recipient firmware informs driver with WMI_DELBA_EVENTID, driver deletes correspondent reorder buffer ADDBA request processing requires sending WMI command, therefore it is processed in work queue context. Same work queue used as for connect, it get renamed to wq_service Signed-off-by:
-
Miaoqing Pan authored
Signed-off-by:
Miaoqing Pan <miaoqing@qca.qualcomm.com> Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Miaoqing Pan authored
Signed-off-by:
-
Miaoqing Pan authored
Signed-off-by:
-
Miaoqing Pan authored
Signed-off-by:
-
- 09 Jan, 2015 27 commits
-
-
Kalle Valo authored
Major changes in ath10k: * Device tree support * Major restructuring how to handle different WMI interface versions * Add WMI TLV interface in preparation for new firmware interface support * Support new firmware branch 10.2.4 * Add thermal cooling interface * Add hwmon interface to read temparture from the device And of course lots of small fixes and cleanups.
-
Kalle Valo authored
kbuild reported a linking error: ERROR: "devm_hwmon_device_register_with_groups" [drivers/net/wireless/ath/ath10k/ath10k_core.ko] undefined! Fix it by returning early and letting the compiler to optimise out the function call. Signed-off-by:Kalle Valo <kvalo@qca.qualcomm.com>
-
Larry Finger authored
Several of the drivers still were defining their own copies of various macros. These are all moved into the core. Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Larry Finger authored
Convert driver to use routine rtl_dm_diginit(). Signed-off-by:
-
Larry Finger authored
Convert driver rtl8723be to use routine rtl_dm_diginit(). Signed-off-by:
-
Larry Finger authored
Convert driver rtl8723ae to use common routine rtl_dm_diginit(). Signed-off-by:
-
Larry Finger authored
Convert driver rtl8192ee to use the common routine to initialize dm_digtable. Signed-off-by:
-
Larry Finger authored
This patch converts driver rtl8192de to use the common routine to initialize dm_digtable. Signed-off-by:
-
Larry Finger authored
These changes convert both rtl8192ce and rtl8192cu to use the new routine. Some additional definitions are needed in the core, thus several of the headers for other drivers are affected, but no other executable code is changed. Signed-off-by:
-
Larry Finger authored
The previous patch created a routine in rtlwifi to initialize dm_digtable. Driver rtl8188ee is converted to use that routine. Signed-off-by:
-
Larry Finger authored
Each of the drivers contains a routine that initializes the dm_digtable member of the driver's private area. As a first step toward reducing the size of the drivers, a copy of this driver is created in rtlwifi, and the definitions of the parameters are moved there. Signed-off-by:
-
Larry Finger authored
The description of the power-save variables for this driver is not as clear as for the others. The wording is changed to match the others. Signed-off-by:
-
Larry Finger authored
Some drivers refer to a particular quantity in the driver's private are by one name, while others use a different name. These differences are removed. Signed-off-by:
-
Arend van Spriel authored
Instead of defining SDIO device identifier in brcm80211 code use the defintions in linux/mmc/sdio_ids.h directly. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Eliad Peller authored
After having all the dfs infrastructure in place, declare radar_detect_widths support for the ap interfaces combination. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
-
Guy Mishol authored
Add dfs region to the reg domain channel update command. Signed-off-by:
Guy Mishol <guym@ti.com> Signed-off-by:
-
Eliad Peller authored
Since we are going to support dfs channels, there is no reason to mark them as NO_IR (having the DFS flag is enough anyway). Additionally, when setting the regdomain configuration, enable usable dfs channels. Signed-off-by:
-
Eliad Peller authored
call wlcore_cmd_dfs_master_restart when starting the ap on a new channel (after csa is done). Add a new WLVIF_FLAG_BEACON_DISABLED flag to indicate that dfs_master_restart command is required. Signed-off-by:
-
Eliad Peller authored
Support ap csa support by implementing the channel_switch_beacon() mac80211 op. Signed-off-by:
-
Eliad Peller authored
Add debugfs file to emulate radar detection through a special fw cmd (which in turn will generate radar event) Signed-off-by:
-
Eliad Peller authored
Add support for CAC start/stop commands, and pass radar detection events from the fw to mac80211. Bump fw name (to wl18xx-fw-4.bin) and min fw version (to 8.9.*.*.11), and align event mailbox accordingly. Signed-off-by:
-
Kobi L authored
Enable ELP authorization in AP mode and enable the use of the wakeup bit in the ELP register. Introduce AP role sleep configuration which is disabled by default. When configured, it allows the AP to sleep when ELP is authorized for it. Signed-off-by:
Kobi Leibovitch <kobi.lev100@gmail.com> Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
-
Eliad Peller authored
configure wowlan when host is suspended in AP mode, since the FW can now wake the host up on Rx. Signed-off-by:
-
Ram Amrani authored
Add the ability to mask FW interrupts on RX BA activity, PSM entry/exit and fast-link notifications. This is used when the host is suspended in order to decrease redundant wake ups. Signed-off-by:
Ram Amrani <ramrani@ti.com> Signed-off-by:
-
Eliad Peller authored
sta_rc_update runs in atomic context. thus, a new work should be scheduled in order to configure the fw with the required configuration. Signed-off-by:
-
Eliad Peller authored
Use kstrtoul_from_user() for reading the user value, and fix the following sparse warning: drivers/net/wireless/ti/wlcore/debugfs.c:937:15: error: incompatible types in comparison expression (different type sizes) Signed-off-by:
-
Eliad Peller authored
The attribute type is binary data (with max length). Signed-off-by:
-
- 07 Jan, 2015 7 commits
-
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.function = f; -t.data = d; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by:
-
Julia Lawall authored
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. A simplified version of the semantic match that fixes this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by:
-
