Merge tag 'v3.6-rc1-iio-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus

IIO fixes for v3.6-rc1

These mostly consist of fixes from Lars-Peter Clausen that were
the first part of a large series reworking the drivers concerned.
Turns out these drivers had quite a wealth of minor bugs.

Also here are some build warning fixes for lm3533-als and
adjd_s111 (both new drives in this cycle).
Final elements are a a div factor overflow and a warning
related fix in a couple of Analog Devices drivers.

All in all nothing major, but a worthwhile bunch of short
fixes.

Fix below build warnings:
  CC [M]  drivers/iio/light/lm3533-als.o
drivers/iio/light/lm3533-als.c:667:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: (near initialization for 'dev_attr_in_illuminance0_thresh_either_en.show') [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: (near initialization for 'dev_attr_in_illuminance0_thresh_either_en.store') [enabled by default]
Signed-off-by: Axel Lin <axel.lin@gmail.com>

The values reported by the AD7780 are unsigned with a binary offset:

	0x000000 is negative fullscale
	0x800000 is zeroscale
	0xffffff is positive fullscale

So mark the channel in the channel spec as unsigned rather than signed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The temperature channel reports values in degree Kelvin with sensitivity of 5630
codes per degree. If the chip is configured in bipolar mode there is an
additional binary offset of 0x800000 and the sensitivity is divided by two.

Currently the driver does the mapping from the raw value to degree Celsius when
doing a manual conversion. This has several disadvantages, the major one being
that it does not work for buffered mode, also by doing the division by the
sensitivity in the driver the precession of the reported value is needlessly
reduced.

Furthermore the current calculation only works in bipolar mode and the current
scale is of by a factor of 1000.

This patch modifies the driver to report correct offset and scale values in
both unipolar and bipolar mode and to report the raw temperature value
for manual conversions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In bipolar mode there is a a binary offset of 2**(N-1) (with N being the number
of bits) on the reported value. Currently this value is subtracted when doing a
manual read. While this works for manual channel readings it does not work for
buffered mode. So report the offset in the channels offset property, which will
work in both modes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>

The values reported by the AD7793 are unsigned.
	In uniploar mode:
			0x000000 is zeroscale
			0xffffff is fullscale
	In bipolar mode:
			0x000000 is negative fullscale
			0x800000 is zeroscale
			0xffffff is positive fullscale

In bipolar mode there is a binary offset, but the values are still unsigned.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Write to the correct register when setting the ACX bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Without the break statement we fall right through to the default case and return
an error value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The internal reference for the ad7793 and similar is 1.17V
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Make the "in-in_scale_available" attribute follow the new naming spec and
rename it to "in_voltage-voltage_scale_available".
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The temperature channel uses the internal 1.17V reference with 0.81 mv/C. The
reported temperature is in Kevlin, so we need to add the Kelvin to Celcius
offset when reporting the offset for the temperature channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In bipolar mode there is a a binary offset of 2**(N-1) (with N being the number
of bits) on the reported value. Currently this value is subtracted when doing a
manual read. While this works for manual channel readings it does not work for
buffered mode. So report the offset in the channels offset property, which will
work in both modes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The values reported by the AD7793 are unsigned.
	In uniploar mode:
			0x000000 is zeroscale
			0xffffff is fullscale
	In bipolar mode:
			0x000000 is negative fullscale
			0x800000 is zeroscale
			0xffffff is positive fullscale

In bipolar mode there is a binary offset, but the values are still unsigned.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Without the break statement we fall right through to the default case and return
an error value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Do not leak memory by updating pointer with potentially NULL realloc return value.
There is no need to preserve data in the buffer,
so replace krealloc() by kfree()-kmalloc() pair.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

With small channel spacing values and high reference frequencies it is
possible to exceed the range of the 10-bit counter.
Workaround by checking the range and widening some constrains.

We don't use the REG1_PHASE value in this case the datasheet recommends to set
it to 1 if not used.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

drivers/staging/iio/adc/ad7298_ring.c:97:37: warning: 'time_ns' may
be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ravishankar Karkala Mallikarjunayya <ravishankar.km@greenturtles.in>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Cc: Bernd Porr <berndporr@f2s.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Randy noticed that with CONFIG_INET turned off, the following build
errors happen:
	ERROR: "register_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
	ERROR: "unregister_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 3902a370 (staging: comedi:
refactor comedi_device_attach() a bit) by yours truly introduced an
inverted logic bug in comedi_device_attach() for the case where the
driver expects the device to be configured by driver name rather than
board name.  The result of a strcmp() is being tested incorrectly.  Fix
it.

Thanks to Stephen N Chivers for discovering the bug and suggesting the
fix.

Cc: <stable@vger.kernel.org> # 3.5.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().

Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().

Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().

Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As mentioned by Ian Abbott, this driver originally checked
the pci_dev subsystem_device in order to make sure that the
pci_dev was compatible with this driver. The cleanup of the
"find pci device" code removed this check. Add it back.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As mentioned by Ian Abbott, the comedi pci drivers that try to
locate an unused pci device with the pci_is_enabled() test
might actually skip over a perfectly good unused device. This
test is also not consistent with the other comedi pci drivers.

Remove the test from all the comedi pci drivers.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1

Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>