- 25 Apr, 2008 27 commits
-
-
Chris Snook authored
There's no good reason to manually set the flash vendor in a module parameter, outside of an Atheros hardware lab. Remove it, so nobody accidentally bricks their board using it incorrectly. Signed-off-by:
Chris Snook <csnook@redhat.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com>
-
Francois Romieu authored
- useless initialization (korina_ope / korina_restart) - use a single variable for the status code in korina_probe and propagate the error status code from below - useless checks in korina_remove : the variables are necessarily set when korina_probe succeeds Signed-off-by:
Francois Romieu <romieu@fr.zoreil.com> Signed-off-by:
-
Francois Romieu authored
The driver takes the error unwind path without condition. Signed-off-by:
-
Krzysztof Halasa authored
Signed-off-by:
Krzysztof Hałasa <khc@pm.waw.pl> Signed-off-by:
-
Cédric Augonnet authored
The local variable "prefix" is never used anymore, and the content of this string appears a bit later, directly in a call to "alloc_netdev" after doing exactly the same if/else test. So there seems to be no point keeping those 4 lines anymore. Signed-off-by:
Cédric Augonnet <cedric.augonnet@ens-lyon.org> Signed-off-by:
-
Francois Romieu authored
Signed-off-by:
-
Grant Grundler authored
While trying to fix http://bugzilla.kernel.org/show_bug.cgi?id=8952 I looked at a few other drivers to figure out what drivers _should_ be doing for suspend/resume. I noticed typhoon driver is likely doing more than it needs to. Patch below is untested since I don't have the HW. Suspend/resume code across NIC drivers is fairly inconsistent. And I couldn't find any documentation on what the canonical sequence NICs need to do for suspend or resume. Is there any? Barring contrary advice, I'm going model the tulip suspend/resume fixes after tg3.c since a number of "modern" (< 5 years old) laptops have that and I'm silly enough to assume it works. Signed-off-by:
-
Valentine Barshak authored
This patch adds ibm_newemac PHY clock workaround for 440EP/440GR EMAC attached to a PHY which doesn't generate RX clock if there is no link. The code is based on the previous ibm_emac driver stuff. The 440EP/440GR allows controlling each EMAC clock separately as opposed to global clock selection for 440GX. BenH: Made that #ifdef CONFIG_PPC_DCR_NATIVE for now as dcri_* stuff doesn't exist for MMIO type DCRs like Cell. Some future rework & improvements of the DCR infrastructure will make that cleaner but for now, this makes it work. Signed-off-by:
Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Valentine Barshak authored
The PowerPC 440GX Taishan board fails to reset EMAC3 (reset timeout error) if there's no link. Because of that it fails to find PHY chip. The older ibm_emac driver had a workaround for that: the EMAC_CLK_INTERNAL/EMAC_CLK_EXTERNAL macros, which toggle the Ethernet Clock Select bit in the SDR0_MFR register. This patch does the same for "ibm,emac-440gx" compatible chips. The workaround forces clock on -all- EMACs, so we select clock under global emac_phy_map_lock. BenH: Made that #ifdef CONFIG_PPC_DCR_NATIVE for now as dcri_* stuff doesn't exist for MMIO type DCRs like Cell. Some future rework & improvements of the DCR infrastructure will make that cleaner but for now, this makes it work. Signed-off-by:
-
Josh Boyer authored
Convert ibm_newemac to use the of_device_is_available function when checking for unused/unwired EMACs. We leave the current check for an "unused" property to maintain backwards compatibility for older device trees. Newer device trees should simply use the standard "status" property in the EMAC node. Signed-off-by:
Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by:
-
Josh Boyer authored
This patch fixes several section mismatch warnings in the ibm_newemac driver similar to: WARNING: vmlinux.o(.devinit.text+0x3a04): Section mismatch in reference from the function emac_probe() to the function .devexit.text:tah_detach() The function __devinit emac_probe() references a function __devexit tah_detach(). Signed-off-by:
-
Stefan Roese authored
On some 4xx PPC's (e.g. 460EX/GT), the rx channel number is a multiple of 8 (e.g. 8 for EMAC1, 16 for EMAC2), but enabling in MAL_RXCASR needs the divided by 8 value for the bitmask. Signed-off-by:
Stefan Roese <sr@denx.de> Signed-off-by:
-
Stefan Roese authored
This fixes the jumbo frame support on EMAC V4 systems. Now the correct bit is set depending on the EMAC version configured. Tested on Kilauea (405EX) and Canyonlands (460EX). Signed-off-by:
-
Jesse Brandeburg authored
Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by:
Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by:
-
Auke Kok authored
To enable EEH support for pci-express network adapters, pcie/msi state needs to be saved and restored for that adapter. [after similar patches for ixgbe and e1000e from Wendy Xiong] Signed-off-by:
-
Wendy Xiong authored
To enable EEH support for pci-express network adapters, pcie/msi state needs to be saved and restored for that adapter. Tested this EEH patch with 2ports and 4ports pci-express e1000e adapters. Signed-off-by:
Wendy Xiong <wendyx@us.ibm.com> Signed-off-by:
-
Wendy Xiong authored
To enable EEH support for pci-express network adapters, pcie/msi state needs to be saved and restored for that adapter. Tested this EEH patch with Intel 10G pci-express ixgbe adapter. Signed-off-by:
-
Auke Kok authored
The lower limit of 80 descriptors in the ring is only valid for one older 8254x chipset. All e1000e devices can use as low as 64 descriptors. Signed-off-by:
-
David Graham authored
Several components to this complex fix. The es2lan cards occasionally gave a "HW Error" especially when forcing speed. Some users also reported that the BMC stole ARP packets. The fixes include setting the proper SW_FW bits to tell the BMC that we're active and not do any un-initialization at all, so the setup routine is largely changed. Signed-off-by:
David Graham <david.graham@intel.com> Signed-off-by:
-
Auke Kok authored
The ethtool -c / -C interface can now be used to modify the irq moderation algorithm. This change does not require an adapter reset and can thus be used at all times. The adapter only supports changing/reading rx-usecs which has special values for 0, 1 and 3: 0 - no irq moderation whatsoever 1 - normal moderation favoring regular mixed traffic (default) 3 - best attempt at low latency possible at cost of CPU For values between 10 and 10000 the rx-usecs defines "the minimum time between successive irqs" in usec, unlike the module parameter. Signed-off-by:
-
Bruce Allan authored
Several stats registers are completely unused and we just waste pci bus time reading them. We also omit using the high 32 bits of the GORC/ GOTC counters. We can just read clear them and only read the low registers. Mii-tool can also break es2lan if it executes a MII PHY register ioctl while the device is in autonegotiation. Unfortunately it seems that several applications and installations still perform this ioctl call periodically and especially in this crucial startup time. We can fool the ioctl by providing fail safe information that mimics the "down" link state and only perform the dangerous PHY reads once after link comes up to fill in the real values. As long as link stays up the information will not change. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Sreenivasa Honnur authored
- Removed rx_lock and put_lock as the buffer replenishment and receive completion is handled serially. Signed-off-by:
Surjit Reang <surjit.reang@neterion.com> Signed-off-by:
Sreenivasa Honnur <sreenivasa.honnur@neterion.com> Signed-off-by:
Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by:
-
Sreenivasa Honnur authored
- Removed receive buffer replenishment tasklet s2io_tasklet and instead allocating the receive buffers in either the interrupt handler (no napi) or the napi handler (napi enabled). Signed-off-by:
-
Sreenivasa Honnur authored
- Updated version number. Signed-off-by:
Santosh Rastapur <santosh.rastapur@neterion.com> Signed-off-by:
-
Sreenivasa Honnur authored
- Fix the memory leak during free_tx_buffers. Signed-off-by:
-
Andy Fleming authored
The patch that changed mdio_bus to a string didn't conflict strongly enough with the patch that added fixed PHY support to UCC. Gather it back into the fold. Fixes this error: ... CC drivers/net/ucc_geth.o 'ucc_geth_probe': /home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/net/ucc_geth.c:3935: error: incompatible types in assignment make[3]: *** [drivers/net/ucc_geth.o] Error 1 Signed-off-by:
Andy Fleming <afleming@freescale.com> Signed-off-by:
-
Brian Haley authored
net/key/af_key.c: In function ‘pfkey_spddelete’: net/key/af_key.c:2359: warning: ‘pol_ctx’ may be used uninitialized in this function When CONFIG_SECURITY_NETWORK_XFRM isn't set, security_xfrm_policy_alloc() is an inline that doesn't set pol_ctx, so this seemed like the easiest fix short of using *uninitialized_var(pol_ctx). Signed-off-by:
Brian Haley <brian.haley@hp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 24 Apr, 2008 13 commits
-
-
David S. Miller authored
Since these operations don't go through the normal device calls, we have to ensure we synchronize with those paths. Noticed by Alan Cox. Signed-off-by: -
Pavel Emelyanov authored
Plan C: we can follow the Al Viro's proposal about %n like in this patch. The same applies to udp, fib (the /proc/net/route file), rt_cache and sctp debug. This is minus ~150-200 bytes for each. Signed-off-by:
Pavel Emelyanov <xemul@openvz.org> Signed-off-by:
-
David Woodhouse authored
When drivers call request_module(), it tries to do something with UNIX sockets and triggers a 'runaway loop modprobe net-pf-1' warning. Avoid this by initialising AF_UNIX support earlier. Signed-off-by:
David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
Patrick McHardy authored
ASSERT_RTNL uses mutex_trylock to test whether the rtnl_mutex is held. This bogus warnings when running in atomic context, which f.e. happens when adding secondary unicast addresses through macvlan or vlan or when synchronizing multicast addresses from wireless devices. Mid-term we might want to consider moving all address updates to process context since the locking seems overly complicated, for now just fix the bogus warning by changing ASSERT_RTNL to use mutex_is_locked(). Signed-off-by:
Patrick McHardy <kaber@trash.net> Signed-off-by:
-
David S. Miller authored
-
Zhu Yi authored
On Wed, 2008-04-23 at 13:38 +0300, Tomas Winkler wrote: > This patch fixes problem in Makefile that prevented > built-in compilation of iwlcore Here is the second part. Without this, drivers/net/wireless/iwlwifi/build-in.o will not be linked into vmlinux. Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
David S. Miller authored
Noticed by Alan Cox. The IFF_UP test is a bit racey, because other entities outside of this driver's ioctl handler can modify that state, even though this ioctl handler runs under lock_kernel(). Signed-off-by: -
Paulius Zaleckas authored
Use stats which now is in the net_device instead of one declared in ppp structure. Kill ppp_net_stats function, because by default it is used identical internal_stats function from net/core/dev.c Signed-of-by:
Paulius Zaleckas <paulius.zaleckas@teltonika.lt> Signed-off-by:
-
Roland Dreier authored
Commit b716bb91 ("iwlwifi: Cancel scanning upon association") moved the test of priv->vif in iwl{3945,4964}_mac_config_interface() outside of where priv->mutex is held, but still tries to do mutex_unlock() on return. This is clearly wrong and triggers a nasty lockdep warning when this codepath is triggered. Fix this by removing the mutex_unlock(). Signed-off-by:
Roland Dreier <rolandd@cisco.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Roel Kluin authored
priv->param_workaround_interval is unsigned, modparam_workaround_interval not. the former is never < 0. Signed-off-by:
Roel Kluin <12o3l@tiscali.nl> Signed-off-by:
-
Roel Kluin authored
previously in this function: u32 index = (dwrq->flags & IW_ENCODE_INDEX) - 1; index is unsigned, so if -1, the original test (below) didn't work. Signed-off-by:
-
Luis Carlos Cobo authored
This patch updates mesh EID values, some of which where conflicting with already-approved 11h EIDs (pointed out by Tomas Winkler). I wanted to use the values suggested in the last available 802.11 draft (2.0) but it assigns 50 to MESH_CONFIG, the same value than EXT_SUPP_RATES. Using the values proposed in the draft incremented by one. Signed-off-by:
Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by:
-
Michael Buesch authored
Some mainboards/CPUs don't allow DMA masks bigger than a certain limit. Some VIA crap^h^h^h^hdevices have an upper limit of 0xFFFFFFFF. So in this case a 64-bit b43 device would always fail to acquire the mask. Implement a workaround to fallback to lower DMA mask, as we can always also support a lower mask. Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
-
