* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: ahci enclosure management bit mask
  libata: ahci enclosure management led sync
  pata_ninja32: suspend/resume support
  libata: Fix LBA48 on pata_it821x RAID volumes.
  libata: clear saved xfer_mode and ncq_enabled on device detach
  sata_sil24: configure max read request size to 4k
  libata: add missing kernel-doc
  libata: fix device iteration bugs
  ahci: Add support for Promise PDC42819
  ata: Switch all my stuff to a common address

Enclosure management bit mask definitions.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Synchronize ahci_sw_activity and ahci_sw_activity_blink with ata_port lock.
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

[http://lkml.org/lkml/2008/10/18/82]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

libata EH saves xfer_mode and ncq_enabled at start to later set
DUBIOUS_XFER flag if it has changed.  These values need to be cleared
on device detach such that hot device swap doesn't accidentally miss
DUBIOUS_XFER.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Due to request posting limitations, bandwidth of sil3132 is limited to
around 120MB/s with the minimum pci-e payload size (128bytes) which is
used by most consumer systems.  However, write throughput can be
slightly (~3%) increased by increasing the max read requeset size.
Configure it to 4k which is the maximum supported.  This optimization
is also done by SIMG's windows driver.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Fix libata missing kernel-doc:

Warning(lin2628-rc2//drivers/ata/libata-core.c:4562): No description
found for parameter 'tag'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

There were several places where only enabled devices should be
iterated over but device enabledness wasn't checked.

* IDENTIFY data 40 wire check in cable_is_40wire()
* xfer_mode/ncq_enabled saving in ata_scsi_error()
* DUBIOUS_XFER handling in ata_set_mode()

While at it, reformat comments in cable_is_40wire().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Add an appropriate entry for the Promise PDC42819 controller. It has an
AHCI mode and so far works correctly with board_ahci.

This chip is found on Promise's FastTrak TX2650 (2 port) and TX4650 (4 port)
software-based RAID cards (for which there is a binary driver, t3sas) and
can be found on some motherboards, for example the MSI K9A2 Platinum,
which calls the chip a Promise T3 controller.

Although this controller also supports SAS devices, its default bootup mode
is AHCI and the binary driver has to do some magic to get the chip into the
appropriate mode to drive SAS disks.

Seeing as no documentation is provided by Promise, adding this entry to the
ahci driver allows the controller to be useful to people as a SATA
controller (with no ill effects on the system if a SAS disk is connected -
probing of the port just times out with "link online but device
misclassified"), without having to resort to using the binary driver. Users
who require SAS or the proprietary software raid can get this functionality
using the binary driver.
Signed-off-by: Mark Nelson <mdnelson8@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  libata: fix NCQ devices behind port multipliers
  scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map

For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

Right now callers have to check whether scsi_host->bqt is already
set up, it's much cleaner to just have scsi_init_shared_tag_map()
does this check on its own.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
  MIPS: lemote/lm2e: Added io_map_base to pci controller
  MIPS: TXx9: Make firmware parameter passing more robust
  MIPS: Markeins: Remove unnecessary define and cleanup comments, etc.
  MIPS: Markeins: Extract ll_emma2rh_* functions
  MIPS: Markeins: Remove runtime debug prints
  MIPS: EMMA: Fold arch/mips/emma/{common,markeins}/irq*.c into markeins/irq.c
  MIPS: EMMA2RH: Remove emma2rh_gpio_irq_base
  MIPS: EMMA2RH: Remove emma2rh_sw_irq_base
  MIPS: EMMA2RH: Remove emma2rh_irq_base global variable
  MIPS: EMMA2RH: Remove emma2rh_sync on read operation
  MIPS: EMMA: Move <asm/emma2rh> to <asm/emma> dir
  MIPS: EMMA: Move arch/mips/emma2rh/ into arch/mips/emma/
  MIPS: EMMA: Kconfig reorganization
  MIPS: Add CONFIG_CPU_R5500 for NEC VR5500 series processors
  MIPS: RB532: Disable the right device
  MIPS: Add support for NXP PNX833x (STB222/5) into linux kernel
  MIPS: TXx9: CONFIG_TOSHIBA_RBTX4939 spelling
  MIPS: Fix KGDB build error
  INPUT: sgi_btns: Add license specification
  MIPS: IP22: ip22-int.c header file weeding.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: fw-sbp2: fix races
  firewire: fw-sbp2: delay first login to avoid retries
  firewire: fw-ohci: initialization failure path fixes
  firewire: fw-ohci: don't leak dma memory on module removal
  firewire: fix struct fw_node memory leak
  firewire: Survive more than 256 bus resets

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
  ALSA: hda - Restore default pin configs for realtek codecs
  sound: use a common working email address
  pci: use pci_ioremap_bar() in sound/

Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).

Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

These functions are completely ineffective.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove runtime db_* macros as we don't need them any more.  In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Current EMMA2RH irq code is mess.  Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Let's use immediate value, instead.  This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

It's totally a waste of CPU cycles.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

git mv arch/mips/{emma2rh,emma} and fixups Makefiles.  We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

We already have sufficient infrastructure to support VR5500 and VR5500A
series processors.  Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.

This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The following patch add support for the NXP PNX833x SOC.  More
specifically it adds support for the STB222/5 variant. It fixes
the vectored interrupt issue.
Signed-off-by: daniel.j.laird <daniel.j.laird@nxp.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Fix a typo in the comment for the TOSHIBA_RBTX4939 config option
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

In file included from include/linux/ptrace.h:49,
                 from arch/mips/kernel/kgdb.c:25:
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:123: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:124: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:126: error: expected declaration specifiers or '...' before '__u32'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:127: error: expected declaration specifiers or '...' before '__u32'
make[1]: *** [arch/mips/kernel/kgdb.o] Error 1
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The following functions

disable_local1_irq()
disable_local2_irq()
disable_local3_irq()

are needlessly defined global, so make them static. While at it, fix a
whitespace error in the same file.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add smc91x platform device to RBTX4939 board and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add sysfs interface for 7 segment LED and implement access routine for
RBTX4939.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>