second parameter should be the index of the table rather than the value.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Saeed Bshara <saeedb@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ring buffer is almost full due to RX completion messages, a
TX packet may reach the "low watermark" and cause the queue stopped.
If the TX completion arrives earlier than queue stopping, the wakeup
may be missed.

This patch moves the check for the last pending packet to cover both
EAGAIN and success cases, so the queue will be reliably waked up when
necessary.
Reported-and-tested-by: Stephan Klein <stephan.klein@wegfinder.at>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.

 2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.

 3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.

 4) Inifnite loop in bpftool map create, from Alban Crequy.

 5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
    Chaignon.

 6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
    Dumazet.

 7) Buffer overrun in marvell phy driver, from Andrew Lunn.

 8) Several crash and statistics handling fixes to bnxt_en driver, from
    Michael Chan and Vasundhara Volam.

 9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
    amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
    NULL deref, etc).

10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.

11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
    Bruijn.

12) Use after free in l2tp, from Eric Dumazet.

13) IPV6 route destroy races, also from Eric Dumazet.

14) SCTP state machine can erroneously run recursively, fix from Xin
    Long.

15) Adjust AF_PACKET msg_name length checks, add padding bytes if
    necessary. From Willem de Bruijn.

16) Preserve skb_iif, so that forwarded packets have consistent values
    even if fragmentation is involved. From Shmulik Ladkani.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
  udp: fix GRO packet of death
  ipv6: A few fixes on dereferencing rt->from
  rds: ib: force endiannes annotation
  selftests: fib_rule_tests: print the result and return 1 if any tests failed
  ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
  net/tls: avoid NULL pointer deref on nskb->sk in fallback
  selftests: fib_rule_tests: Fix icmp proto with ipv6
  packet: validate msg_namelen in send directly
  packet: in recvmsg msg_name return at least sizeof sockaddr_ll
  sctp: avoid running the sctp state machine recursively
  stmmac: pci: Fix typo in IOT2000 comment
  Documentation: fix netdev-FAQ.rst markup warning
  ipv6: fix races in ip6_dst_destroy()
  l2ip: fix possible use-after-free
  appletalk: Set error code if register_snap_client failed
  net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
  rxrpc: Fix net namespace cleanup
  ipv6/flowlabel: wait rcu grace period before put_pid()
  vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
  tcp: add sanity tests in tcp_add_backlog()
  ...

Pull io_uring fixes from Jens Axboe:
 "This is mostly io_uring fixes/tweaks. Most of these were actually done
  in time for the last -rc, but I wanted to ensure that everything
  tested out great before including them. The code delta looks larger
  than it really is, as it's mostly just comment additions/changes.

  Outside of the comment additions/changes, this is mostly removal of
  unnecessary barriers. In all, this pull request contains:

   - Tweak to how we handle errors at submission time. We now post a
     completion event if the error occurs on behalf of an sqe, instead
     of returning it through the system call. If the error happens
     outside of a specific sqe, we return the error through the system
     call. This makes it nicer to use and makes the "normal" use case
     behave the same as the offload cases. (me)

   - Fix for a missing req reference drop from async context (me)

   - If an sqe is submitted with RWF_NOWAIT, don't punt it to async
     context. Return -EAGAIN directly, instead of using it as a hint to
     do async punt. (Stefan)

   - Fix notes on barriers (Stefan)

   - Remove unnecessary barriers (Stefan)

   - Fix potential double free of memory in setup error (Mark)

   - Further improve sq poll CPU validation (Mark)

   - Fix page allocation warning and leak on buffer registration error
     (Mark)

   - Fix iov_iter_type() for new no-ref flag (Ming)

   - Fix a case where dio doesn't honor bio no-page-ref (Ming)"

* tag 'for-linus-20190502' of git://git.kernel.dk/linux-block:
  io_uring: avoid page allocation warnings
  iov_iter: fix iov_iter_type
  block: fix handling for BIO_NO_PAGE_REF
  io_uring: drop req submit reference always in async punt
  io_uring: free allocated io_memory once
  io_uring: fix SQPOLL cpu validation
  io_uring: have submission side sqe errors post a cqe
  io_uring: remove unnecessary barrier after unsetting IORING_SQ_NEED_WAKEUP
  io_uring: remove unnecessary barrier after incrementing dropped counter
  io_uring: remove unnecessary barrier before reading SQ tail
  io_uring: remove unnecessary barrier after updating SQ head
  io_uring: remove unnecessary barrier before reading cq head
  io_uring: remove unnecessary barrier before wq_has_sleeper
  io_uring: fix notes on barriers
  io_uring: fix handling SQEs requesting NOWAIT

Pull PCI fixes from Bjorn Helgaas:
 "I apologize for sending these so late in the cycle. We went back and
  forth about how to deal with the unexpected logging of intentional
  link state changes and finally decided to just config them off by
  default.

  PCI fixes:

   - Stop ignoring "pci=disable_acs_redir" parameter (Logan Gunthorpe)

   - Use shared MSI/MSI-X vector for Link Bandwidth Management (Alex
     Williamson)

   - Add Kconfig option for Link Bandwidth notification messages (Keith
     Busch)"

* tag 'pci-v5.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI/LINK: Add Kconfig option (default off)
  PCI/portdrv: Use shared MSI/MSI-X vector for Bandwidth Management
  PCI: Fix issue with "pci=disable_acs_redir" parameter being ignored

Pull MTD fix from Richard Weinberger:
 "A single regression fix for the marvell nand driver"

* tag 'mtd/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
  mtd: rawnand: marvell: Clean the controller state before each operation

e8303bb7 ("PCI/LINK: Report degraded links via link bandwidth
notification") added dmesg logging whenever a link changes speed or width
to a state that is considered degraded.  Unfortunately, it cannot
differentiate signal integrity-related link changes from those
intentionally initiated by an endpoint driver, including drivers that may
live in userspace or VMs when making use of vfio-pci.  Some GPU drivers
actively manage the link state to save power, which generates a stream of
messages like this:

  vfio-pci 0000:07:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:02.0 (capable of 64.000 Gb/s with 5 GT/s x16 link)

Since we can't distinguish the intentional changes from the signal
integrity issues, leave the reporting turned off by default.  Add a Kconfig
option to turn it on if desired.

Fixes: e8303bb7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.comSigned-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

syzbot was able to crash host by sending UDP packets with a 0 payload.

TCP does not have this issue since we do not aggregate packets without
payload.

Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.

BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr ffff88808893fff0 by task syz-executor612/7889

CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 __asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
 skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
 udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
 call_gro_receive include/linux/netdevice.h:2349 [inline]
 udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
 udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
 inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
 dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
 napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
 tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
 call_write_iter include/linux/fs.h:1866 [inline]
 do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
 do_iter_write fs/read_write.c:957 [inline]
 do_iter_write+0x184/0x610 fs/read_write.c:938
 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
 do_writev+0x15e/0x370 fs/read_write.c:1037
 __do_sys_writev fs/read_write.c:1110 [inline]
 __se_sys_writev fs/read_write.c:1107 [inline]
 __x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:00007ffe8c716118 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007ffe8c716150 RCX: 0000000000441cc0
RDX: 0000000000000001 RSI: 00007ffe8c716170 RDI: 00000000000000f0
RBP: 0000000000000000 R08: 000000000000ffff R09: 0000000000a64668
R10: 0000000020000040 R11: 0000000000000246 R12: 000000000000c2d9
R13: 0000000000402b50 R14: 0000000000000000 R15: 0000000000000000

Allocated by task 5143:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_kmalloc mm/kasan/common.c:497 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
 kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
 slab_post_alloc_hook mm/slab.h:437 [inline]
 slab_alloc mm/slab.c:3393 [inline]
 kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
 mm_alloc+0x1d/0xd0 kernel/fork.c:1030
 bprm_mm_init fs/exec.c:363 [inline]
 __do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
 do_execveat_common fs/exec.c:1865 [inline]
 do_execve fs/exec.c:1882 [inline]
 __do_sys_execve fs/exec.c:1958 [inline]
 __se_sys_execve fs/exec.c:1953 [inline]
 __x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 5351:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
 __cache_free mm/slab.c:3499 [inline]
 kmem_cache_free+0x86/0x260 mm/slab.c:3765
 __mmdrop+0x238/0x320 kernel/fork.c:677
 mmdrop include/linux/sched/mm.h:49 [inline]
 finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
 context_switch kernel/sched/core.c:2880 [inline]
 __schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
 preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
 retint_kernel+0x1b/0x2d
 arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
 kmem_cache_free+0xab/0x260 mm/slab.c:3766
 anon_vma_chain_free mm/rmap.c:134 [inline]
 unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
 free_pgtables+0x1af/0x2f0 mm/memory.c:394
 exit_mmap+0x2d1/0x530 mm/mmap.c:3144
 __mmput kernel/fork.c:1046 [inline]
 mmput+0x15f/0x4c0 kernel/fork.c:1067
 exec_mmap fs/exec.c:1046 [inline]
 flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
 load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
 search_binary_handler fs/exec.c:1656 [inline]
 search_binary_handler+0x17f/0x570 fs/exec.c:1634
 exec_binprm fs/exec.c:1698 [inline]
 __do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
 do_execveat_common fs/exec.c:1865 [inline]
 do_execve fs/exec.c:1882 [inline]
 __do_sys_execve fs/exec.c:1958 [inline]
 __se_sys_execve fs/exec.c:1953 [inline]
 __x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff88808893f7c0
 which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
 1496-byte region [ffff88808893f7c0, ffff88808893fd98)
The buggy address belongs to the page:
page:ffffea0002224f80 count:1 mapcount:0 mapping:ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw: 01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw: ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                                                             ^
 ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Fixes: e20cf8d3 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull power supply fixes from Sebastian Reichel:
 "Two more fixes for the 5.1 cycle.

  One division by zero fix in a specific driver and one core workaround
  for bad userspace behaviour from systemd regarding uevents. IMHO this
  can be considered to be a userspace bug, but the debug messages are
  useless anyways

   - cpcap-battery: fix a division by zero

   - core: fix systemd issue due to log messages produced by uevent"

* tag 'for-v5.1-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: sysfs: prevent endless uevent loop with CONFIG_POWER_SUPPLY_DEBUG
  power: supply: cpcap-battery: Fix division by zero

It is a followup after the fix in
commit 9c69a132 ("route: Avoid crash from dereferencing NULL rt->from")

rt6_do_redirect():
1. NULL checking is needed on rt->from because a parallel
   fib6_info delete could happen that sets rt->from to NULL.
   (e.g. rt6_remove_exception() and fib6_drop_pcpu_from()).

2. fib6_info_hold() is not enough.  Same reason as (1).
   Meaning, holding dst->__refcnt cannot ensure
   rt->from is not NULL or rt->from->fib6_ref is not 0.

   Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc()
   is already doing, this patch chooses to extend the rcu section
   to keep "from" dereference-able after checking for NULL.

inet6_rtm_getroute():
1. NULL checking is also needed on rt->from for a similar reason.
   Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED.

Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While the endiannes is being handled correctly as indicated by the comment
above the offending line - sparse was unhappy with the missing annotation
as be64_to_cpu() expects a __be64 argument. To mitigate this annotation
all involved variables are changed to a consistent __le64 and the
 conversion to uint64_t delayed to the call to rds_cong_map_updated().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARC fixes from Vineet Gupta:
 "A few minor fixes for ARC.

   - regression in memset if line size !64

   - avoid panic if PAE and IOC"

* tag 'arc-5.1-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: memset: fix build with L1_CACHE_SHIFT != 6
  ARC: [hsdk] Make it easier to add PAE40 region to DTB
  ARC: PAE40: don't panic and instead turn off hw ioc

The Interrupt Message Number in the PCIe Capabilities register (PCIe r4.0,
sec 7.5.3.2) indicates which MSI/MSI-X vector is shared by interrupts
related to the PCIe Capability, including Link Bandwidth Management and
Link Autonomous Bandwidth Interrupts (Link Control, 7.5.3.7), Command
Completed and Hot-Plug Interrupts (Slot Control, 7.5.3.10), and the PME
Interrupt (Root Control, 7.5.3.12).

pcie_message_numbers() checked whether we want to enable PME or Hot-Plug
interrupts but neglected to check for Link Bandwidth Management, so if we
only wanted the Bandwidth Management interrupts, it decided we didn't need
any vectors at all.  Then pcie_port_enable_irq_vec() tried to reallocate
zero vectors, which failed, resulting in fallback to INTx.

On some systems, e.g., an X79-based workstation, that INTx seems broken or
not handled correctly, so we got spurious IRQ16 interrupts for Bandwidth
Management events.

Change pcie_message_numbers() so that if we want Link Bandwidth Management
interrupts, we use the shared MSI/MSI-X vector from the PCIe Capabilities
register.

Fixes: e8303bb7 ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/lkml/155597243666.19387.1205950870601742062.stgit@gimli.homeSigned-off-by: Alex Williamson <alex.williamson@redhat.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

Pull ACPI fix from Rafael Wysocki:
 "Revert a recent ACPICA change that caused initialization to fail on
  systems with Thunderbolt docking stations connected at the init time"

* tag 'acpi-5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "ACPICA: Clear status of GPEs before enabling them"

The 'extent_type' variable does seem to be reliably initialized, but
it's _very_ non-obvious, since there's a "goto next" case that jumps
over the normal initialization.  That will then always trigger the
"start >= extent_end" test, which will end up never falling through to
the use of that variable.

But the code is certainly not obvious, and the compiler warning looks
reasonable.  Make 'extent_type' an int, and initialize it to an invalid
negative value, which seems to be the common pattern in other places.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixes: 65b2b493 ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pvlock_page and hvclock_page variables are (as the name implies)
addresses to pages, created by the linker script.

But we declared them as just "extern u8" variables, which _works_, but
now that gcc does some more bounds checking, it causes warnings like

    warning: array subscript 1 is outside array bounds of ‘u8[1]’

when we then access more than one byte from those variables.

Fix this by simply making the declaration of the variables match
reality, which makes the compiler happy too.
Signed-off-by: Linus Torvalds <torvalds@-linux-foundation.org>

I'm not sure what made gcc warn about this code now.  The 'ret' variable
does end up initialized in all cases, but it's definitely not obvious,
so the compiler is quite reasonable to warn about this.

So just add initialization to make it all much more obvious both to
compilers and to humans.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We already did this for clang, but now gcc has that warning too.  Yes,
yes, the address may be unaligned.  And that's kind of the point.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.

As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.

Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
 - the correct iif is observed if forwarding path does not involve
   fragmentation/refragmentation
 - a bogus iif is observed if forwarding path involves
   fragmentation/refragmentatiom

Fix, by preserving skb_iif during 'ip_copy_metadata'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In io_sqe_buffer_register() we allocate a number of arrays based on the
iov_len from the user-provided iov. While we limit iov_len to SZ_1G,
we can still attempt to allocate arrays exceeding MAX_ORDER.

On a 64-bit system with 4KiB pages, for an iov where iov_base = 0x10 and
iov_len = SZ_1G, we'll calculate that nr_pages = 262145. When we try to
allocate a corresponding array of (16-byte) bio_vecs, requiring 4194320
bytes, which is greater than 4MiB. This results in SLUB warning that
we're trying to allocate greater than MAX_ORDER, and failing the
allocation.

Avoid this by using kvmalloc() for allocations dependent on the
user-provided iov_len. At the same time, fix a leak of imu->bvec when
registration fails.

Full splat from before this patch:

WARNING: CPU: 1 PID: 2314 at mm/page_alloc.c:4595 __alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 2314 Comm: syz-executor326 Not tainted 5.1.0-rc7-dirty #4
Hardware name: linux,dummy-virt (DT)
Call trace:
 dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
 show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x110/0x190 lib/dump_stack.c:113
 panic+0x384/0x68c kernel/panic.c:214
 __warn+0x2bc/0x2c0 kernel/panic.c:571
 report_bug+0x228/0x2d8 lib/bug.c:186
 bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
 call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
 brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
 do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
 el1_dbg+0x18/0x8c
 __alloc_pages_nodemask+0x7ac/0x2938 mm/page_alloc.c:4595
 alloc_pages_current+0x164/0x278 mm/mempolicy.c:2132
 alloc_pages include/linux/gfp.h:509 [inline]
 kmalloc_order+0x20/0x50 mm/slab_common.c:1231
 kmalloc_order_trace+0x30/0x2b0 mm/slab_common.c:1243
 kmalloc_large include/linux/slab.h:480 [inline]
 __kmalloc+0x3dc/0x4f0 mm/slub.c:3791
 kmalloc_array include/linux/slab.h:670 [inline]
 io_sqe_buffer_register fs/io_uring.c:2472 [inline]
 __io_uring_register fs/io_uring.c:2962 [inline]
 __do_sys_io_uring_register fs/io_uring.c:3008 [inline]
 __se_sys_io_uring_register fs/io_uring.c:2990 [inline]
 __arm64_sys_io_uring_register+0x9e0/0x1bc8 fs/io_uring.c:2990
 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
 invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
 el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
 el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
 el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
   (ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,23000438
Memory Limit: none
Rebooting in 1 seconds..

Fixes: edafccee ("io_uring: add support for pre-mapped user IO buffers")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

update_chksum() accesses nskb->sk before it has been set
by complete_skb(), move the init up.

Fixes: e8f69799 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.

Fixes: 5e1a99ea ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.

Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.

Change v1->v2: initialize addr in all paths

Fixes: 6b8d95f1 ("packet: validate address length if non-zero")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.

This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.

Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.

Change v1->v2: do not overwrite zeroed padding again. use copy_len.

Fixes: 0fb375fb ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 875f1d07 ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
introduces one extra flag of ITER_BVEC_FLAG_NO_REF, and this flag
is stored into iter->type.

However, iov_iter_type() doesn't consider the new added flag, fix
it by masking this flag in iov_iter_type().

Fixes: 875f1d07 ("iov_iter: add ITER_BVEC_FLAG_NO_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Commit 399254aa ("block: add BIO_NO_PAGE_REF flag") introduces
BIO_NO_PAGE_REF, and once this flag is set for one bio, all pages
in the bio won't be get/put during IO.

However, if one bio is submitted via __blkdev_direct_IO_simple(),
even though BIO_NO_PAGE_REF is set, pages still may be put.

Fixes this issue by avoiding to put pages if BIO_NO_PAGE_REF is
set.

Fixes: 399254aa ("block: add BIO_NO_PAGE_REF flag")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If we don't end up actually calling submit in io_sq_wq_submit_work(),
we still need to drop the submit reference to the request. If we
don't, then we can leak the request. This can happen if we race
with ring shutdown while flushing the workqueue for requests that
require use of the mm_struct.

Fixes: e65ef56d ("io_uring: use regular request ref counts")
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If io_allocate_scq_urings() fails to allocate an sq_* region, it will
call io_mem_free() for any previously allocated regions, but leave
dangling pointers to these regions in the ctx. Any regions which have
not yet been allocated are left NULL. Note that when returning
-EOVERFLOW, the previously allocated sq_ring is not freed, which appears
to be an unintentional leak.

When io_allocate_scq_urings() fails, io_uring_create() will call
io_ring_ctx_wait_and_kill(), which calls io_mem_free() on all the sq_*
regions, assuming the pointers are valid and not NULL.

This can result in pages being freed multiple times, which has been
observed to corrupt the page state, leading to subsequent fun. This can
also result in virt_to_page() on NULL, resulting in the use of bogus
page addresses, and yet more subsequent fun. The latter can be detected
with CONFIG_DEBUG_VIRTUAL on arm64.

Adding a cleanup path to io_allocate_scq_urings() complicates the logic,
so let's leave it to io_ring_ctx_free() to consistently free these
pointers, and simplify the io_allocate_scq_urings() error paths.

Full splats from before this patch below. Note that the pointer logged
by the DEBUG_VIRTUAL "non-linear address" warning has been hashed, and
is actually NULL.

[   26.098129] page:ffff80000e949a00 count:0 mapcount:-128 mapping:0000000000000000 index:0x0
[   26.102976] flags: 0x63fffc000000()
[   26.104373] raw: 000063fffc000000 ffff80000e86c188 ffff80000ea3df08 0000000000000000
[   26.108917] raw: 0000000000000000 0000000000000001 00000000ffffff7f 0000000000000000
[   26.137235] page dumped because: VM_BUG_ON_PAGE(page_ref_count(page) == 0)
[   26.143960] ------------[ cut here ]------------
[   26.146020] kernel BUG at include/linux/mm.h:547!
[   26.147586] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[   26.149163] Modules linked in:
[   26.150287] Process syz-executor.21 (pid: 20204, stack limit = 0x000000000e9cefeb)
[   26.153307] CPU: 2 PID: 20204 Comm: syz-executor.21 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #18
[   26.156566] Hardware name: linux,dummy-virt (DT)
[   26.158089] pstate: 40400005 (nZcv daif +PAN -UAO)
[   26.159869] pc : io_mem_free+0x9c/0xa8
[   26.161436] lr : io_mem_free+0x9c/0xa8
[   26.162720] sp : ffff000013003d60
[   26.164048] x29: ffff000013003d60 x28: ffff800025048040
[   26.165804] x27: 0000000000000000 x26: ffff800025048040
[   26.167352] x25: 00000000000000c0 x24: ffff0000112c2820
[   26.169682] x23: 0000000000000000 x22: 0000000020000080
[   26.171899] x21: ffff80002143b418 x20: ffff80002143b400
[   26.174236] x19: ffff80002143b280 x18: 0000000000000000
[   26.176607] x17: 0000000000000000 x16: 0000000000000000
[   26.178997] x15: 0000000000000000 x14: 0000000000000000
[   26.181508] x13: 00009178a5e077b2 x12: 0000000000000001
[   26.183863] x11: 0000000000000000 x10: 0000000000000980
[   26.186437] x9 : ffff000013003a80 x8 : ffff800025048a20
[   26.189006] x7 : ffff8000250481c0 x6 : ffff80002ffe9118
[   26.191359] x5 : ffff80002ffe9118 x4 : 0000000000000000
[   26.193863] x3 : ffff80002ffefe98 x2 : 44c06ddd107d1f00
[   26.196642] x1 : 0000000000000000 x0 : 000000000000003e
[   26.198892] Call trace:
[   26.199893]  io_mem_free+0x9c/0xa8
[   26.201155]  io_ring_ctx_wait_and_kill+0xec/0x180
[   26.202688]  io_uring_setup+0x6c4/0x6f0
[   26.204091]  __arm64_sys_io_uring_setup+0x18/0x20
[   26.205576]  el0_svc_common.constprop.0+0x7c/0xe8
[   26.207186]  el0_svc_handler+0x28/0x78
[   26.208389]  el0_svc+0x8/0xc
[   26.209408] Code: aa0203e0 d0006861 9133a021 97fcdc3c (d4210000)
[   26.211995] ---[ end trace bdb81cd43a21e50d ]---

[   81.770626] ------------[ cut here ]------------
[   81.825015] virt_to_phys used for non-linear address: 000000000d42f2c7 (          (null))
[   81.827860] WARNING: CPU: 1 PID: 30171 at arch/arm64/mm/physaddr.c:15 __virt_to_phys+0x48/0x68
[   81.831202] Modules linked in:
[   81.832212] CPU: 1 PID: 30171 Comm: syz-executor.20 Not tainted 5.1.0-rc7-00004-g7d30b2ea43d6 #19
[   81.835616] Hardware name: linux,dummy-virt (DT)
[   81.836863] pstate: 60400005 (nZCv daif +PAN -UAO)
[   81.838727] pc : __virt_to_phys+0x48/0x68
[   81.840572] lr : __virt_to_phys+0x48/0x68
[   81.842264] sp : ffff80002cf67c70
[   81.843858] x29: ffff80002cf67c70 x28: ffff800014358e18
[   81.846463] x27: 0000000000000000 x26: 0000000020000080
[   81.849148] x25: 0000000000000000 x24: ffff80001bb01f40
[   81.851986] x23: ffff200011db06c8 x22: ffff2000127e3c60
[   81.854351] x21: ffff800014358cc0 x20: ffff800014358d98
[   81.856711] x19: 0000000000000000 x18: 0000000000000000
[   81.859132] x17: 0000000000000000 x16: 0000000000000000
[   81.861586] x15: 0000000000000000 x14: 0000000000000000
[   81.863905] x13: 0000000000000000 x12: ffff1000037603e9
[   81.866226] x11: 1ffff000037603e8 x10: 0000000000000980
[   81.868776] x9 : ffff80002cf67840 x8 : ffff80001bb02920
[   81.873272] x7 : ffff1000037603e9 x6 : ffff80001bb01f47
[   81.875266] x5 : ffff1000037603e9 x4 : dfff200000000000
[   81.876875] x3 : ffff200010087528 x2 : ffff1000059ecf58
[   81.878751] x1 : 44c06ddd107d1f00 x0 : 0000000000000000
[   81.880453] Call trace:
[   81.881164]  __virt_to_phys+0x48/0x68
[   81.882919]  io_mem_free+0x18/0x110
[   81.886585]  io_ring_ctx_wait_and_kill+0x13c/0x1f0
[   81.891212]  io_uring_setup+0xa60/0xad0
[   81.892881]  __arm64_sys_io_uring_setup+0x2c/0x38
[   81.894398]  el0_svc_common.constprop.0+0xac/0x150
[   81.896306]  el0_svc_handler+0x34/0x88
[   81.897744]  el0_svc+0x8/0xc
[   81.898715] ---[ end trace b4a703802243cbba ]---

Fixes: 2b188cc1 ("Add io_uring IO interface")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-block@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>

In io_sq_offload_start(), we call cpu_possible() on an unbounded cpu
value from userspace. On v5.1-rc7 on arm64 with
CONFIG_DEBUG_PER_CPU_MAPS, this results in a splat:

  WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]

There was an attempt to fix this in commit:

  917257da ("io_uring: only test SQPOLL cpu after we've verified it")

... by adding a check after the cpu value had been limited to NR_CPU_IDS
using array_index_nospec(). However, this left an unbound check at the
start of the function, for which the warning still fires.

Let's fix this correctly by checking that the cpu value is bound by
nr_cpu_ids before passing it to cpu_possible(). Note that only
nr_cpu_ids of a cpumask are guaranteed to exist at runtime, and
nr_cpu_ids can be significantly smaller than NR_CPUs. For example, an
arm64 defconfig has NR_CPUS=256, while my test VM has 4 vCPUs.

Following the intent from the commit message for 917257da, the
check is moved under the SQ_AFF branch, which is the only branch where
the cpu values is consumed. The check is performed before bounding the
value with array_index_nospec() so that we don't silently accept bogus
cpu values from userspace, where array_index_nospec() would force these
values to 0.

I suspect we can remove the array_index_nospec() call entirely, but I've
conservatively left that in place, updated to use nr_cpu_ids to match
the prior check.

Tested on arm64 with the Syzkaller reproducer:

  https://syzkaller.appspot.com/bug?extid=cd714a07c6de2bc34293
  https://syzkaller.appspot.com/x/repro.syz?x=15d8b397200000

Full splat from before this patch:

WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_check include/linux/cpumask.h:128 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 cpumask_test_cpu include/linux/cpumask.h:344 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_sq_offload_start fs/io_uring.c:2244 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_create fs/io_uring.c:2864 [inline]
WARNING: CPU: 1 PID: 27601 at include/linux/cpumask.h:121 io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 27601 Comm: syz-executor.0 Not tainted 5.1.0-rc7 #3
Hardware name: linux,dummy-virt (DT)
Call trace:
 dump_backtrace+0x0/0x2f0 include/linux/compiler.h:193
 show_stack+0x20/0x30 arch/arm64/kernel/traps.c:158
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x110/0x190 lib/dump_stack.c:113
 panic+0x384/0x68c kernel/panic.c:214
 __warn+0x2bc/0x2c0 kernel/panic.c:571
 report_bug+0x228/0x2d8 lib/bug.c:186
 bug_handler+0xa0/0x1a0 arch/arm64/kernel/traps.c:956
 call_break_hook arch/arm64/kernel/debug-monitors.c:301 [inline]
 brk_handler+0x1d4/0x388 arch/arm64/kernel/debug-monitors.c:316
 do_debug_exception+0x1a0/0x468 arch/arm64/mm/fault.c:831
 el1_dbg+0x18/0x8c
 cpu_max_bits_warn include/linux/cpumask.h:121 [inline]
 cpumask_check include/linux/cpumask.h:128 [inline]
 cpumask_test_cpu include/linux/cpumask.h:344 [inline]
 io_sq_offload_start fs/io_uring.c:2244 [inline]
 io_uring_create fs/io_uring.c:2864 [inline]
 io_uring_setup+0x1108/0x15a0 fs/io_uring.c:2916
 __do_sys_io_uring_setup fs/io_uring.c:2929 [inline]
 __se_sys_io_uring_setup fs/io_uring.c:2926 [inline]
 __arm64_sys_io_uring_setup+0x50/0x70 fs/io_uring.c:2926
 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline]
 invoke_syscall arch/arm64/kernel/syscall.c:47 [inline]
 el0_svc_common.constprop.0+0x148/0x2e0 arch/arm64/kernel/syscall.c:83
 el0_svc_handler+0xdc/0x100 arch/arm64/kernel/syscall.c:129
 el0_svc+0x8/0xc arch/arm64/kernel/entry.S:948
SMP: stopping secondary CPUs
Dumping ftrace buffer:
   (ftrace buffer empty)
Kernel Offset: disabled
CPU features: 0x002,23000438
Memory Limit: none
Rebooting in 1 seconds..

Fixes: 917257da ("io_uring: only test SQPOLL cpu after we've verified it")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-block@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

Simplied the logic
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Ying triggered a call trace when doing an asconf testing:

  BUG: scheduling while atomic: swapper/12/0/0x10000100
  Call Trace:
   <IRQ>  [<ffffffffa4375904>] dump_stack+0x19/0x1b
   [<ffffffffa436fcaf>] __schedule_bug+0x64/0x72
   [<ffffffffa437b93a>] __schedule+0x9ba/0xa00
   [<ffffffffa3cd5326>] __cond_resched+0x26/0x30
   [<ffffffffa437bc4a>] _cond_resched+0x3a/0x50
   [<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
   [<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
   [<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
   [<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
   [<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
   [<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
   [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
   [<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
   [<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
   [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
   [<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
   [<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
   [<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]

As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.

Vlad tried to fix this recursive call in Commit c0786693 ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.

To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix ReST underline warning:

./Documentation/networking/netdev-FAQ.rst:135: WARNING: Title underline too short.

Q: I made changes to only a few patches in a patch series should I resend only those changed?
--------------------------------------------------------------------------------------------

Fixes: ffa91253 ("Documentation: networking: Update netdev-FAQ regarding patches")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we only post a cqe if we get an error OUTSIDE of submission.
For submission, we return the error directly through io_uring_enter().
This is a bit awkward for applications, and it makes more sense to
always post a cqe with an error, if the error happens on behalf of an
sqe.

This changes submission behavior a bit. io_uring_enter() returns -ERROR
for an error, and > 0 for number of sqes submitted. Before this change,
if you wanted to submit 8 entries and had an error on the 5th entry,
io_uring_enter() would return 4 (for number of entries successfully
submitted) and rewind the sqring. The application would then have to
peek at the sqring and figure out what was wrong with the head sqe, and
then skip it itself. With this change, we'll return 5 since we did
consume 5 sqes, and the last sqe (with the error) will result in a cqe
being posted with the error.

This makes the logic easier to handle in the application, and it cleans
up the submission part.
Suggested-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

We had many syzbot reports that seem to be caused by use-after-free
of struct fib6_info.

ip6_dst_destroy(), fib6_drop_pcpu_from() and rt6_remove_exception()
are writers vs rt->from, and use non consistent synchronization among
themselves.

Switching to xchg() will solve the issues with no possible
lockdep issues.

BUG: KASAN: user-memory-access in atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:294 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:292 [inline]
BUG: KASAN: user-memory-access in fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
BUG: KASAN: user-memory-access in fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
Write of size 4 at addr 0000000000ffffb4 by task syz-executor.1/7649

CPU: 0 PID: 7649 Comm: syz-executor.1 Not tainted 5.1.0-rc6+ #183
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 kasan_report.cold+0x5/0x40 mm/kasan/report.c:321
 check_memory_region_inline mm/kasan/generic.c:185 [inline]
 check_memory_region+0x123/0x190 mm/kasan/generic.c:191
 kasan_check_write+0x14/0x20 mm/kasan/common.c:108
 atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
 fib6_info_release include/net/ip6_fib.h:294 [inline]
 fib6_info_release include/net/ip6_fib.h:292 [inline]
 fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
 fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
 fib6_del_route net/ipv6/ip6_fib.c:1813 [inline]
 fib6_del+0xac2/0x10a0 net/ipv6/ip6_fib.c:1844
 fib6_clean_node+0x3a8/0x590 net/ipv6/ip6_fib.c:2006
 fib6_walk_continue+0x495/0x900 net/ipv6/ip6_fib.c:1928
 fib6_walk+0x9d/0x100 net/ipv6/ip6_fib.c:1976
 fib6_clean_tree+0xe0/0x120 net/ipv6/ip6_fib.c:2055
 __fib6_clean_all+0x118/0x2a0 net/ipv6/ip6_fib.c:2071
 fib6_clean_all+0x2b/0x40 net/ipv6/ip6_fib.c:2082
 rt6_sync_down_dev+0x134/0x150 net/ipv6/route.c:4057
 rt6_disable_ip+0x27/0x5f0 net/ipv6/route.c:4062
 addrconf_ifdown+0xa2/0x1220 net/ipv6/addrconf.c:3705
 addrconf_notify+0x19a/0x2260 net/ipv6/addrconf.c:3630
 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1753
 call_netdevice_notifiers_extack net/core/dev.c:1765 [inline]
 call_netdevice_notifiers net/core/dev.c:1779 [inline]
 dev_close_many+0x33f/0x6f0 net/core/dev.c:1522
 rollback_registered_many+0x43b/0xfd0 net/core/dev.c:8177
 rollback_registered+0x109/0x1d0 net/core/dev.c:8242
 unregister_netdevice_queue net/core/dev.c:9289 [inline]
 unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9282
 unregister_netdevice include/linux/netdevice.h:2658 [inline]
 __tun_detach+0xd5b/0x1000 drivers/net/tun.c:727
 tun_detach drivers/net/tun.c:744 [inline]
 tun_chr_close+0xe0/0x180 drivers/net/tun.c:3443
 __fput+0x2e5/0x8d0 fs/file_table.c:278
 ____fput+0x16/0x20 fs/file_table.c:309
 task_work_run+0x14a/0x1c0 kernel/task_work.c:113
 exit_task_work include/linux/task_work.h:22 [inline]
 do_exit+0x90a/0x2fa0 kernel/exit.c:876
 do_group_exit+0x135/0x370 kernel/exit.c:980
 __do_sys_exit_group kernel/exit.c:991 [inline]
 __se_sys_exit_group kernel/exit.c:989 [inline]
 __x64_sys_exit_group+0x44/0x50 kernel/exit.c:989
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458da9
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffeafc2a6a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 000000000000001c RCX: 0000000000458da9
RDX: 0000000000412a80 RSI: 0000000000a54ef0 RDI: 0000000000000043
RBP: 00000000004be552 R08: 000000000000000c R09: 000000000004c0d1
R10: 0000000002341940 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00007ffeafc2a7f0 R14: 000000000004c065 R15: 00007ffeafc2a800

Fixes: a68886a6 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull fsnotify fix from Jan Kara:
 "A fix of user trigerable NULL pointer dereference syzbot has recently
  spotted.

  The problem was introduced in this merge window so no CC stable is
  needed"

* tag 'fsnotify_for_v5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: Fix NULL ptr deref in fanotify_get_fsid()

Revert commit c8b1917c ("ACPICA: Clear status of GPEs before
enabling them") that causes problems with Thunderbolt controllers
to occur if a dock device is connected at init time (the xhci_hcd
and thunderbolt modules crash which prevents peripherals connected
through them from working).

Commit c8b1917c effectively causes commit ecc1165b ("ACPICA:
Dispatch active GPEs at init time") to get undone, so the problem
addressed by commit ecc1165b appears again as a result of it.

Fixes: c8b1917c ("ACPICA: Clear status of GPEs before enabling them")
Link: https://lore.kernel.org/lkml/s5hy33siofw.wl-tiwai@suse.de/T/#u
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1132943Reported-by: Michael Hirmke <opensuse@mike.franken.de>
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: 4.17+ <stable@vger.kernel.org> # 4.17+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Merge tag 'wireless-drivers-for-davem-2019-04-30' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 5.1

Third set of fixes for 5.1.

iwlwifi

* fix an oops when creating debugfs entries

* fix bug when trying to capture debugging info while in rfkill

* prevent potential uninitialized memory dumps into debugging logs

* fix some initialization parameters for AX210 devices

* fix an oops with non-MSIX devices

* fix an oops when we receive a packet with bogus lengths

* fix a bug that prevented 5350 devices from working

* fix a small merge damage from the previous series

mwifiex

* fig regression with resume on SDIO

ath10k

* fix locking problem with crashdump

* fix warnings during suspend and resume

Also note that this pull conflicts with net-next. And I want to emphasie
that it's really net-next, so when you pull this to net tree it should
go without conflicts. Stephen reported the conflict here:

https://lkml.kernel.org/r/20190429115338.5decb50b@canb.auug.org.au

In iwlwifi oddly commit 154d4899 adds the IS_ERR_OR_NULL() in
wireless-drivers but commit c9af7528 removes the whole check in
wireless-drivers-next. The fix is easy, just drop the whole check for
mvmvif->dbgfs_dir in iwlwifi/mvm/debugfs-vif.c, it's unneeded anyway.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull USB fixes from Greg KH:
 "Here are some small USB fixes for a bunch of warnings/errors that the
  syzbot has been finding with it's new-found ability to stress-test the
  USB layer.

  All of these are tiny, but fix real issues, and are marked for stable
  as well. All of these have had lots of testing in linux-next as well"

* tag 'usb-5.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: w1 ds2490: Fix bug caused by improper use of altsetting array
  USB: yurex: Fix protection fault after device removal
  usb: usbip: fix isoc packet num validation in get_pipe
  USB: core: Fix bug caused by duplicate interface PM usage counter
  USB: dummy-hcd: Fix failure to give back unlinked URBs
  USB: core: Fix unterminated string returned by usb_string()

There is no operation to order with afterwards, and removing the flag is
not critical in any way.

There will always be a "race condition" where the application will
trigger IORING_ENTER_SQ_WAKEUP when it isn't actually needed.
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>