There is no need to use hex_dump_to_buffer() in the cases like this:

	hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false);	/* len <= 16 */
	sprintf("%s\n", outbuf);

since it maybe easily converted to simple:

	sprintf("%*ph\n", len, buf);

Note: it seems in one case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.

When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Another pull request for the next cycle, this time with quite
a bit of content:
 * mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
 * TDLS higher bandwidth support (Arik)
 * OCB fixes from Bertold Van den Bergh
 * suspend/resume fixes from Eliad
 * dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
 * VHT bitrate mask support (Lorenzo Bianconi)
 * better regulatory support for 5/10 MHz channels (Matthias May)
 * basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.

Add more information to schedule scan complete message.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Lmac sched scan supports partial scans, so we can set some channels to be
scanned on every scan iteration and others to be scanned only on some
iterations. Currently we set all channels to be scanned every iteration,
but still have some configuration of which iterations should be partial
and which should be full.

Remove all partial/full scan configuration to reduce confusions.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove timing values from iwl_mvm_scan_params and use defines and
arrays of values instead.

While at that fix few values and corner cases and align all OSs
to ChromeOS values.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We added calls to d3_suspend/resume trans ops during the
suspend/resume flow.

However, the wrapper code didn't verify the trans ops were
actually defined, resulting in panic when they were not
(such as in the case of sdio trans)

Fixes: 6dfb36c8 ("iwlwifi: call d3_suspend/resume in d0i3 case as well")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The bit was not according to ieee80211 specification.
Fix that.
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of using the out-of-line average calculation, use the new
DECLARE_EWMA() macro to declare a signal EWMA, and use that.

This actually *reduces* the code size slightly (on x86-64) while
also reducing the station info size by 80 bytes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Having the EWMA parameters stored in the runtime struct imposes
memory requirements for the constant values that could just be
inlined in the code. This particularly makes sense if there are
a lot of such structs, for example in mac80211 in the station
table where each station has a number of these in an array, and
there can be many stations.

Provide a macro DECLARE_EWMA() that declares the necessary struct
and inline functions to access it with the parameters hard-coded;
using this also means the user no longer needs to 'select AVERAGE'
as it's entirely self-contained.

In the mac80211 case, on x86-64, this actually slightly *reduces*
code size, while also saving 80 bytes of runtime memory per sta.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Define rc_rateidx_vht_mcs_mask array and rate_idx_match_vht_mcs_mask()
method in order to apply mcs mask for vht rates
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Define rate_control_apply_mask_ratetbl() in order to apply ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove ieee80211_tx_rate dependency in rate_idx_match_legacy_mask(),
rate_idx_match_mcs_mask() and rate_idx_match_mask() in order to use the
previous logic to define a ratemask in rate_control_set_rates() for
station rate table. Moreover move rate mask definition logic in
rate_control_cap_mask()
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove unnecessary ieee80211_tx_info pointer from rate_control_apply_mask
signature. rate_control_apply_mask() will be used to define a ratemask in
rate_control_set_rates() for station rate table
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Perform the BSS_CHANGED_BSSID action when joining an OCB network.
This is required to set the broadcast BSSID in some network drivers.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently OCB mode accepts frames with bssid==broadcast and type!=beacon.
Some non-data frames are sent matching this, for example probe responses.
This results in unnecessary creation of STA entries.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To make mac80211 accept the multicast rate requested by the user the
rate control should be told that it is operating in BSS mode.
Without this, the default rate is selected in rate_control_send_low
(!pubsta and !txrc->bss)
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow setting multicast rate on OCB interfaces.
Current behaviour results in EOPNOTSUPP when attempting this.
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If driver failed to setup wiphy params (e.g. rts
threshold, fragmentation treshold) userspace
wasn't properly notified about this. This could
lead to user confusion who would think the command
succeeded even if that wasn't the case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The original assumption of 20MHz wide channels hasn't been true since
the addition of support for 5 and 10 MHz channels.
Change the code to no longer disable all channels that don't fit into
the 20MHz grid, but instead set the appropriate flags to disable
operation on specific bandwidths.
Signed-off-by: Matthias May <matthias.may@neratec.com>
[reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The outside if statement checks that IEEE80211_TX_INTFL_MLME_CONN_TX is
set so this condition is always true.  Checking twice upsets the static
checkers.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The iwlwifi driver was the only driver that used this, but as
it turns out it never needed it, so we can remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.

Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.

Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When building a Tx Command for management frames, we are lacking
a check for action frames, for which we should set a different
pm_timeout.  This cause the fw to stay awake for 100TU after each
such frame is transmitted, resulting an excessive power consumption.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Command ID of ToF range request command adapted to new FW commands grouping
scheme.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is slave on the bus(SDIO) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. When the FW wants load / unload pages, it creates an
interrupt,	and the driver uploads / downloads the page to an address in
the a specific address on the device's memory.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on SDIO in order to allow the program to
use a larger virtual space while using less physical memory on the device
itself.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As a preperation for multiple RX queues change the RBD
allocation model.

The new model includes a background allocator. The allocator is
called by the interrupt handler when there are two released
buffers by the queue, and the allocator starts allocating eight
pages per request.
When the queue has released 8 pages it tries claiming the
request. If the pages are not ready - it keeps claiming.
This new model should make sure that RBDs are always available
across the multiple queues.

The RBDs are transferred between the allocator and the queue.
The queue moves the free RBDs upon freeing them to the allocator.
The allocator moves them back to the queue's possession when the
request is claimed.
The allocator has an initial pool to make sure there are always RBDs
available for the request completion.
Release of the buffers at exit is done per pools - the allocator
frees its own initial pool and the queue frees its own pool.

Existing code refactor -
-Queue's initial pool is the size of the queue only as the allocation
of the new buffers no longer uses this pool.
-Removal of replenish background work, and replenish calls in the
interrupt handler and restock().
-The replenish() and the rxq used_list are used only during
initialization.
-Moved page allocation to a new function for code reuse.

New code -
Allocator code - new structure and functions.
Interrupt handler uses the allocator functions for replenishing buffers.
Reuse of the restock() method.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/pcie/internal.h

Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow frag SKBs in PCIe and advertise the maximum number of frags
to the opmode. As a fallback. linearize the SKB if it exceeds the
maximum number of fragments. This allows using the hardware better
(filling more TBs) and should improve performance when used by the
opmode.

Also adjust tracing to be able to deal with this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Gscan is a scan feature which is supported on certain devices only,
hence the need for a TLV flag for it. For devices that support gscan
store the gscan capabilities advertised by the FW so the driver can
report it to upper layers.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Set max TX aggregation size for 8260 SDIO devices series to 40 frames.
Fine tune max RX aggregation size - change it to 21.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Our firmware scheduler used to suffer from false wake-up on 500 time units.
We had to came up with a formula to address this buggy behavior.
Now that our firmware is fixed, we can go back to our old policy.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for dumping all the RBs in the RX queue
when FW error occurs.
This will assist debugging.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Print the CPU1 and CPU2 secured boot status registers from the NIC
to indicate a SYSASSERT during secured engine unlocking process
on init/protocol image.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove outdated and unused definitions
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support for extended command id in triggers handling.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>