commit a0e80fbd upstream.

The flash loader has been seen on a Telit UE910 modem. The flash loader
is a bit special, it presents both an ACM and CDC Data interface but
only the latter is useful. Unless a magic string is sent to the device
it will disappear and the regular modem device appears instead.
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit f33a7f72 upstream.

Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.

The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.

"This is what happens when the device is turned on (without modifying
the drivers):

[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device

This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:

[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14

Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 8f1eb487 upstream.

New created file's mode is not masked with umask, and this makes umask not
work for ocfs2 volume.

Fixes: 702e5bc6 ("ocfs2: use generic posix ACL infrastructure")
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Gang He <ghe@suse.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit c812012f upstream.

If we pass in an empty nfs_fattr struct to nfs_update_inode, it will
(correctly) not update any of the attributes, but it then clears the
NFS_INO_INVALID_ATTR flag, which indicates that the attributes are
up to date. Don't clear the flag if the fattr struct has no valid
attrs to apply.
Reviewed-by: Steve French <steve.french@primarydata.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit c68a027c upstream.

If clp->cl_cb_ident is zero, then nfs_cb_idr_remove_locked() skips removing
it when the nfs_client is freed.  A decoding or server bug can then find
and try to put that first nfs_client which would lead to a crash.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Fixes: d6870312 ("nfs4client: convert to idr_alloc()")
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 100ceb66 upstream.

Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers:  Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10".  With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.

However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them.  Only their IsoXmitIntMask register is unreliable at early
access.

With my own JMB381 single function controller I found:
  - I can reproduce the problem with a lower probability than Craig's.
  - If I put a loop around the section which clears and reads
    IsoXmitIntMask, then either the first or the second attempt will
    return the correct initial mask of 0x0000000f.  I never encountered
    a case of needing more than a second attempt.
  - Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
    before the first write, the subsequent read will return the correct
    result.
  - If I merely ignore a wrong read result and force the known real
    result, later isochronous transmit DMA usage works just fine.

So let's just fix this chip bug up by the latter method.  Tested with
JMB381 on kernel 3.13 and 4.3.

Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not.  I never heard
of this issue together with any other chip though.

I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.

Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.

Reported-by: Clifford Dunn
Reported-by: Craig Moore <craig.moore@qenos.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 4327ba52 upstream.

If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the
journaling will be aborted first and the error number will be recorded
into JBD2 superblock and, finally, the system will enter into the
panic state in "errors=panic" option.  But, in the rare case, this
sequence is little twisted like the below figure and it will happen
that the system enters into panic state, which means the system reset
in mobile environment, before completion of recording an error in the
journal superblock. In this case, e2fsck cannot recognize that the
filesystem failure occurred in the previous run and the corruption
wouldn't be fixed.

Task A                        Task B
ext4_handle_error()
-> jbd2_journal_abort()
  -> __journal_abort_soft()
    -> __jbd2_journal_abort_hard()
    | -> journal->j_flags |= JBD2_ABORT;
    |
    |                         __ext4_abort()
    |                         -> jbd2_journal_abort()
    |                         | -> __journal_abort_soft()
    |                         |   -> if (journal->j_flags & JBD2_ABORT)
    |                         |           return;
    |                         -> panic()
    |
    -> jbd2_journal_update_sb_errno()
Tested-by: Hobin Woo <hobin.woo@samsung.com>
Signed-off-by: Daeho Jeong <daeho.jeong@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 6934da92 upstream.

There is a use-after-free possibility in __ext4_journal_stop() in the
case that we free the handle in the first jbd2_journal_stop() because
we're referencing handle->h_err afterwards. This was introduced in
9705acd6 and it is wrong. Fix it by
storing the handle->h_err value beforehand and avoid referencing
potentially freed handle.

Fixes: 9705acd6Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 1d512cb7 upstream.

If we are using the NO_HOLES feature, we have a tiny time window when
running delalloc for a nodatacow inode where we can race with a concurrent
link or xattr add operation leading to a BUG_ON.

This happens because at run_delalloc_nocow() we end up casting a leaf item
of type BTRFS_INODE_[REF|EXTREF]_KEY or of type BTRFS_XATTR_ITEM_KEY to a
file extent item (struct btrfs_file_extent_item) and then analyse its
extent type field, which won't match any of the expected extent types
(values BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]) and therefore trigger an
explicit BUG_ON(1).

The following sequence diagram shows how the race happens when running a
no-cow dellaloc range [4K, 8K[ for inode 257 and we have the following
neighbour leafs:

             Leaf X (has N items)                    Leaf Y

 [ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ]  [ (257 EXTENT_DATA 8192), ... ]
              slot N - 2         slot N - 1              slot 0

 (Note the implicit hole for inode 257 regarding the [0, 8K[ range)

       CPU 1                                         CPU 2

 run_dealloc_nocow()
   btrfs_lookup_file_extent()
     --> searches for a key with value
         (257 EXTENT_DATA 4096) in the
         fs/subvol tree
     --> returns us a path with
         path->nodes[0] == leaf X and
         path->slots[0] == N

   because path->slots[0] is >=
   btrfs_header_nritems(leaf X), it
   calls btrfs_next_leaf()

   btrfs_next_leaf()
     --> releases the path

                                              hard link added to our inode,
                                              with key (257 INODE_REF 500)
                                              added to the end of leaf X,
                                              so leaf X now has N + 1 keys

     --> searches for the key
         (257 INODE_REF 256), because
         it was the last key in leaf X
         before it released the path,
         with path->keep_locks set to 1

     --> ends up at leaf X again and
         it verifies that the key
         (257 INODE_REF 256) is no longer
         the last key in the leaf, so it
         returns with path->nodes[0] ==
         leaf X and path->slots[0] == N,
         pointing to the new item with
         key (257 INODE_REF 500)

   the loop iteration of run_dealloc_nocow()
   does not break out the loop and continues
   because the key referenced in the path
   at path->nodes[0] and path->slots[0] is
   for inode 257, its type is < BTRFS_EXTENT_DATA_KEY
   and its offset (500) is less then our delalloc
   range's end (8192)

   the item pointed by the path, an inode reference item,
   is (incorrectly) interpreted as a file extent item and
   we get an invalid extent type, leading to the BUG_ON(1):

   if (extent_type == BTRFS_FILE_EXTENT_REG ||
      extent_type == BTRFS_FILE_EXTENT_PREALLOC) {
       (...)
   } else if (extent_type == BTRFS_FILE_EXTENT_INLINE) {
       (...)
   } else {
       BUG_ON(1)
   }

The same can happen if a xattr is added concurrently and ends up having
a key with an offset smaller then the delalloc's range end.

So fix this by skipping keys with a type smaller than
BTRFS_EXTENT_DATA_KEY.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit aeafbf84 upstream.

While running a stress test I got the following warning triggered:

  [191627.672810] ------------[ cut here ]------------
  [191627.673949] WARNING: CPU: 8 PID: 8447 at fs/btrfs/file.c:779 __btrfs_drop_extents+0x391/0xa50 [btrfs]()
  (...)
  [191627.701485] Call Trace:
  [191627.702037]  [<ffffffff8145f077>] dump_stack+0x4f/0x7b
  [191627.702992]  [<ffffffff81095de5>] ? console_unlock+0x356/0x3a2
  [191627.704091]  [<ffffffff8104b3b0>] warn_slowpath_common+0xa1/0xbb
  [191627.705380]  [<ffffffffa0664499>] ? __btrfs_drop_extents+0x391/0xa50 [btrfs]
  [191627.706637]  [<ffffffff8104b46d>] warn_slowpath_null+0x1a/0x1c
  [191627.707789]  [<ffffffffa0664499>] __btrfs_drop_extents+0x391/0xa50 [btrfs]
  [191627.709155]  [<ffffffff8115663c>] ? cache_alloc_debugcheck_after.isra.32+0x171/0x1d0
  [191627.712444]  [<ffffffff81155007>] ? kmemleak_alloc_recursive.constprop.40+0x16/0x18
  [191627.714162]  [<ffffffffa06570c9>] insert_reserved_file_extent.constprop.40+0x83/0x24e [btrfs]
  [191627.715887]  [<ffffffffa065422b>] ? start_transaction+0x3bb/0x610 [btrfs]
  [191627.717287]  [<ffffffffa065b604>] btrfs_finish_ordered_io+0x273/0x4e2 [btrfs]
  [191627.728865]  [<ffffffffa065b888>] finish_ordered_fn+0x15/0x17 [btrfs]
  [191627.730045]  [<ffffffffa067d688>] normal_work_helper+0x14c/0x32c [btrfs]
  [191627.731256]  [<ffffffffa067d96a>] btrfs_endio_write_helper+0x12/0x14 [btrfs]
  [191627.732661]  [<ffffffff81061119>] process_one_work+0x24c/0x4ae
  [191627.733822]  [<ffffffff810615b0>] worker_thread+0x206/0x2c2
  [191627.734857]  [<ffffffff810613aa>] ? process_scheduled_works+0x2f/0x2f
  [191627.736052]  [<ffffffff810613aa>] ? process_scheduled_works+0x2f/0x2f
  [191627.737349]  [<ffffffff810669a6>] kthread+0xef/0xf7
  [191627.738267]  [<ffffffff810f3b3a>] ? time_hardirqs_on+0x15/0x28
  [191627.739330]  [<ffffffff810668b7>] ? __kthread_parkme+0xad/0xad
  [191627.741976]  [<ffffffff81465592>] ret_from_fork+0x42/0x70
  [191627.743080]  [<ffffffff810668b7>] ? __kthread_parkme+0xad/0xad
  [191627.744206] ---[ end trace bbfddacb7aaada8d ]---

  $ cat -n fs/btrfs/file.c
  691  int __btrfs_drop_extents(struct btrfs_trans_handle *trans,
  (...)
  758                  btrfs_item_key_to_cpu(leaf, &key, path->slots[0]);
  759                  if (key.objectid > ino ||
  760                      key.type > BTRFS_EXTENT_DATA_KEY || key.offset >= end)
  761                          break;
  762
  763                  fi = btrfs_item_ptr(leaf, path->slots[0],
  764                                      struct btrfs_file_extent_item);
  765                  extent_type = btrfs_file_extent_type(leaf, fi);
  766
  767                  if (extent_type == BTRFS_FILE_EXTENT_REG ||
  768                      extent_type == BTRFS_FILE_EXTENT_PREALLOC) {
  (...)
  774                  } else if (extent_type == BTRFS_FILE_EXTENT_INLINE) {
  (...)
  778                  } else {
  779                          WARN_ON(1);
  780                          extent_end = search_start;
  781                  }
  (...)

This happened because the item we were processing did not match a file
extent item (its key type != BTRFS_EXTENT_DATA_KEY), and even on this
case we cast the item to a struct btrfs_file_extent_item pointer and
then find a type field value that does not match any of the expected
values (BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]). This scenario happens
due to a tiny time window where a race can happen as exemplified below.
For example, consider the following scenario where we're using the
NO_HOLES feature and we have the following two neighbour leafs:

               Leaf X (has N items)                    Leaf Y

[ ... (257 INODE_ITEM 0) (257 INODE_REF 256) ]  [ (257 EXTENT_DATA 8192), ... ]
          slot N - 2         slot N - 1              slot 0

Our inode 257 has an implicit hole in the range [0, 8K[ (implicit rather
than explicit because NO_HOLES is enabled). Now if our inode has an
ordered extent for the range [4K, 8K[ that is finishing, the following
can happen:

          CPU 1                                       CPU 2

  btrfs_finish_ordered_io()
    insert_reserved_file_extent()
      __btrfs_drop_extents()
         Searches for the key
          (257 EXTENT_DATA 4096) through
          btrfs_lookup_file_extent()

         Key not found and we get a path where
         path->nodes[0] == leaf X and
         path->slots[0] == N

         Because path->slots[0] is >=
         btrfs_header_nritems(leaf X), we call
         btrfs_next_leaf()

         btrfs_next_leaf() releases the path

                                                  inserts key
                                                  (257 INODE_REF 4096)
                                                  at the end of leaf X,
                                                  leaf X now has N + 1 keys,
                                                  and the new key is at
                                                  slot N

         btrfs_next_leaf() searches for
         key (257 INODE_REF 256), with
         path->keep_locks set to 1,
         because it was the last key it
         saw in leaf X

           finds it in leaf X again and
           notices it's no longer the last
           key of the leaf, so it returns 0
           with path->nodes[0] == leaf X and
           path->slots[0] == N (which is now
           < btrfs_header_nritems(leaf X)),
           pointing to the new key
           (257 INODE_REF 4096)

         __btrfs_drop_extents() casts the
         item at path->nodes[0], slot
         path->slots[0], to a struct
         btrfs_file_extent_item - it does
         not skip keys for the target
         inode with a type less than
         BTRFS_EXTENT_DATA_KEY
         (BTRFS_INODE_REF_KEY < BTRFS_EXTENT_DATA_KEY)

         sees a bogus value for the type
         field triggering the WARN_ON in
         the trace shown above, and sets
         extent_end = search_start (4096)

         does the if-then-else logic to
         fixup 0 length extent items created
         by a past bug from hole punching:

           if (extent_end == key.offset &&
               extent_end >= search_start)
               goto delete_extent_item;

         that evaluates to true and it ends
         up deleting the key pointed to by
         path->slots[0], (257 INODE_REF 4096),
         from leaf X

The same could happen for example for a xattr that ends up having a key
with an offset value that matches search_start (very unlikely but not
impossible).

So fix this by ensuring that keys smaller than BTRFS_EXTENT_DATA_KEY are
skipped, never casted to struct btrfs_file_extent_item and never deleted
by accident. Also protect against the unexpected case of getting a key
for a lower inode number by skipping that key and issuing a warning.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 7ba0c47c upstream.

We need to wait for the flying timers, since we
are going to free the mrtable right after it.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit d71e6a11 upstream.

The kernel was using the vendor ID 0xd00d1e, which was inherited from
the old ieee1394 driver stack.  However, this ID was not registered, and
invalid.

Instead, use the vendor/model IDs that are now officially assigned to
the kernel:
https://ieee1394.wiki.kernel.org/index.php/IEEE_OUI_Assignments

[stefanr:
  - The vendor ID 001f11 is Openmoko, Inc.'s identifier, registered at
    IEEE Registration Authority.
  - The range of model IDs 023900...0239ff are the Linux kernel 1394
    subsystem's identifiers, registered at Openmoko.
  - Model ID 023901 is picked by the subsystem developers as
    firewire-core's model ID.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: "Oliver Neukum" <ONeukum@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 96fffb4f upstream.

This happens when networking namespaces are enabled.
Suggested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit cc4998fe upstream.

--accept-local  option works for res.type == RTN_LOCAL, which should be
from the local table, but there, the fib_info's nh->nh_scope =
RT_SCOPE_NOWHERE ( > RT_SCOPE_HOST). in fib_create_info().

	if (cfg->fc_scope == RT_SCOPE_HOST) {
		struct fib_nh *nh = fi->fib_nh;

		/* Local address is added. */
		if (nhs != 1 || nh->nh_gw)
			goto err_inval;
		nh->nh_scope = RT_SCOPE_NOWHERE;   <===
		nh->nh_dev = dev_get_by_index(net, fi->fib_nh->nh_oif);
		err = -ENODEV;
		if (!nh->nh_dev)
			goto failure;

but in our rpfilter_lookup_reverse():

	if (dev_match || flags & XT_RPFILTER_LOOSE)
		return FIB_RES_NH(res).nh_scope <= RT_SCOPE_HOST;

if nh->nh_scope > RT_SCOPE_HOST, it will fail. --accept-local option
will never be passed.

it seems the test is bogus and can be removed to fix this issue.

	if (dev_match || flags & XT_RPFILTER_LOOSE)
		return FIB_RES_NH(res).nh_scope <= RT_SCOPE_HOST;

ipv6 does not have this issue.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 37815bf8 upstream.

The module notifier call chain for MODULE_STATE_COMING was moved up before
the parsing of args, into the complete_formation() call. But if the module failed
to load after that, the notifier call chain for MODULE_STATE_GOING was
never called and that prevented the users of those call chains from
cleaning up anything that was allocated.

Link: http://lkml.kernel.org/r/554C52B9.9060700@gmail.comReported-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Fixes: 4982223e "module: set nx before marking module MODULE_STATE_COMING"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

BugLink: http://bugs.launchpad.net/bugs/1512815

commit e81107d4 upstream.

My colleague ran into a program stall on a x86_64 server, where
n_tty_read() was waiting for data even if there was data in the buffer
in the pty.  kernel stack for the stuck process looks like below.
 #0 [ffff88303d107b58] __schedule at ffffffff815c4b20
 #1 [ffff88303d107bd0] schedule at ffffffff815c513e
 #2 [ffff88303d107bf0] schedule_timeout at ffffffff815c7818
 #3 [ffff88303d107ca0] wait_woken at ffffffff81096bd2
 #4 [ffff88303d107ce0] n_tty_read at ffffffff8136fa23
 #5 [ffff88303d107dd0] tty_read at ffffffff81368013
 #6 [ffff88303d107e20] __vfs_read at ffffffff811a3704
 #7 [ffff88303d107ec0] vfs_read at ffffffff811a3a57
 #8 [ffff88303d107f00] sys_read at ffffffff811a4306
 #9 [ffff88303d107f50] entry_SYSCALL_64_fastpath at ffffffff815c86d7

There seems to be two problems causing this issue.

First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active().  However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
   RELEASE may be completed before the
   RELEASE operation has completed */
                                        add_wait_queue(&tty->read_wait, &wait);
                                        ...
                                        if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.

        __receive_buf()                         n_tty_read()
------------------------------------------------------------------------
                                        spin_lock_irqsave(&q->lock, flags);
                                        /* from add_wait_queue() */
                                        ...
                                        if (!input_available_p(tty, 0)) {
                                        /* Memory operations issued after the
                                           RELEASE may be completed before the
                                           RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
                  ldata->read_head);
if (waitqueue_active(&tty->read_wait))
                                        __add_wait_queue(q, wait);
                                        spin_unlock_irqrestore(&q->lock,flags);
                                        /* from add_wait_queue() */
                                        ...
                                        timeout = wait_woken(&wait,
                                          TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------

There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.

This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation).  Moreover, the resulting code is much simpler.

Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[jsalisbury: Backported to 3.13.y:
 - Use wake_up_interruptible(), not wake_up_interruptible_poll()
 - There are only two spurious uses of waitqueue_active() to remove]
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit a91e627e upstream.

One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4.  For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:

correct:       CH345:
0F FE 00 00    0F FE 00 00
04 F0 01 02    04 F0 01 02
04 03 04 05    0F 03 04 05
04 06 07 08    04 06 07 08
04 09 0A 0B    0F 09 0A 0B
04 0C 0D 0E    04 0C 0D 0E
05 F7 00 00    05 F7 00 00

A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored.  The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".

These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.

(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 1ca8b201 upstream.

The CH345 USB MIDI chip has two output ports.  However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.

It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port.  So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 98d362be upstream.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 638148e2 upstream.

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit e07af133 upstream.

Also known as Verizon U620L.

The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:

 $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4

This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 1bcb49e6 upstream.

The Honeywell HGI80 is a wireless interface to the evohome connected
thermostat. It uses a TI 3410 USB-serial port.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 705e63d2 upstream.

There is a bit of a mess in the order of arguments to the ulpi write
callback. There is

	int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)

in drivers/usb/common/ulpi.c;

	struct usb_phy_io_ops {
		...
		int (*write)(struct usb_phy *x, u32 val, u32 reg);
	}

in include/linux/usb/phy.h.

The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.

Fixes: ffb865b1 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 19cd80a2 upstream.

It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.

This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G        W       4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
 [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
 [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
 [<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...

Commit 7f477358 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 5accd17d upstream.

For reasons not entirely apparent, but now enshrined in history, the
architectural mapping of AArch32 banked registers to AArch64 registers
actually orders SP_<mode> and LR_<mode> backwards compared to the
intuitive r13/r14 order, for all modes except FIQ.

Fix the compat_<reg>_<mode> macros accordingly, in the hope of avoiding
subtle bugs with KVM and AArch32 guests.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 7cecd9ab upstream.

According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.

Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
  in operating state
- A bus error condition occurs which activates EI interrupt, system is
  still suspended which means EI interrupt will be not be handled nor
  cleared.

If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.

By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 18e0afab upstream.

T: Bus=04 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cf3 ProdID=817b Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1506615Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit cd355ff0 upstream.

This adapter works with the existing linux-firmware.

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=021c Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/1502781Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 660f0fc0 upstream.

The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:

    commit 5205185d
    Author: David Herrmann <dh.herrmann@gmail.com>
    Date:   Sat Apr 6 20:28:47 2013 +0200

        Bluetooth: hidp: remove old session-management

The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.

Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call

    getsockopt(..., SO_ERROR, ...)

..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Reported-by: Mark Haun <haunma@keteu.org>
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 1e6e6328 upstream.

This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Frans van de Wiel <fvdw@fvdw.eu>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 1f9c6e1b upstream.

There were several bugs here.

1)  The done label was in the wrong place so we didn't copy any
    information out when there was no command given.

2)  We were using PAGE_SIZE as the size of the buffer instead of
    "PAGE_SIZE - pos".

3)  snprintf() returns the number of characters that would have been
    printed if there were enough space.  If there was not enough space
    (and we had fixed the memory corruption bug #2) then it would result
    in an information leak when we do simple_read_from_buffer().  I've
    changed it to use scnprintf() instead.

I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.

Fixes: 5e6e3a92 ('wireless: mwifiex: initial commit for Marvell mwifiex driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 2502d0ef upstream.

The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.

However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.

This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.

Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 8ec6d978 upstream.

The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.

Fixes: 615f7b9b ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 581b7f15 upstream.

There appears to be no formal statement of what pv_irq_ops.save_fl() is
supposed to return precisely.  Native returns the full flags, while lguest and
Xen only return the Interrupt Flag, and both have comments by the
implementations stating that only the Interrupt Flag is looked at.  This may
have been true when initially implemented, but no longer is.

To make matters worse, the Xen PVOP leaves the upper bits undefined, making
the BUG_ON() undefined behaviour.  Experimentally, this now trips for 32bit PV
guests on Broadwell hardware.  The BUG_ON() is consistent for an individual
build, but not consistent for all builds.  It has also been a sitting timebomb
since SMAP support was introduced.

Use native_save_fl() instead, which will obtain an accurate view of the AC
flag.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Tested-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: <lguest@lists.ozlabs.org>
Cc: Xen-devel <xen-devel@lists.xen.org>
Link: http://lkml.kernel.org/r/1433323874-6927-1-git-send-email-andrew.cooper3@citrix.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 04633df0 upstream.

When we get loaded by a 64-bit bootloader, kernel entry point is
startup_64 in head_64.S. We don't trust any and all bootloaders because
some will fiddle with CPU configuration so we go ahead and massage each
CPU into sanity again.

For example, some dell BIOSes have this XD disable feature which set
IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround
for other OSes but Linux sure doesn't need it.

A similar thing is present in the Surface 3 firmware - see
https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit
only on the BSP:

  # rdmsr -a 0x1a0
  400850089
  850089
  850089
  850089

I know, right?!

There's not even an off switch in there.

So fix all those cases by sanitizing the 64-bit entry point too. For
that, make verify_cpu() callable in 64-bit mode also.
Requested-and-debugged-by: "H. Peter Anvin" <hpa@zytor.com>
Reported-and-tested-by: Bastien Nocera <bugzilla@hadess.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1446739076-21303-1-git-send-email-bp@alien8.deSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 68accac3 upstream.

The commit f5f3497c extended the low identity mapping. However, if
the kernel uses more than 2 GB (VMSPLIT_2G_OPT or VMSPLIT_1G memory
split), the normal memory mapping is overwritten by the low identity
mapping causing a crash. To avoid overwritting, limit the low identity
map to cover only memory before kernel range (PAGE_OFFSET).

Fixes: f5f3497c "x86/setup: Extend low identity map to cover whole kernel range
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: http://lkml.kernel.org/r/1446815916-22105-1-git-send-email-krzysiek@podlesie.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit f5f3497c upstream.

On 32-bit systems, the initial_page_table is reused by
efi_call_phys_prolog as an identity map to call
SetVirtualAddressMap.  efi_call_phys_prolog takes care of
converting the current CPU's GDT to a physical address too.

For PAE kernels the identity mapping is achieved by aliasing the
first PDPE for the kernel memory mapping into the first PDPE
of initial_page_table.  This makes the EFI stub's trick "just work".

However, for non-PAE kernels there is no guarantee that the identity
mapping in the initial_page_table extends as far as the GDT; in this
case, accesses to the GDT will cause a page fault (which quickly becomes
a triple fault).  Fix this by copying the kernel mappings from
swapper_pg_dir to initial_page_table twice, both at PAGE_OFFSET and at
identity mapping.

For some reason, this is only reproducible with QEMU's dynamic translation
mode, and not for example with KVM.  However, even under KVM one can clearly
see that the page table is bogus:

    $ qemu-system-i386 -pflash OVMF.fd -M q35 vmlinuz0 -s -S -daemonize
    $ gdb
    (gdb) target remote localhost:1234
    (gdb) hb *0x02858f6f
    Hardware assisted breakpoint 1 at 0x2858f6f
    (gdb) c
    Continuing.

    Breakpoint 1, 0x02858f6f in ?? ()
    (gdb) monitor info registers
    ...
    GDT=     0724e000 000000ff
    IDT=     fffbb000 000007ff
    CR0=0005003b CR2=ff896000 CR3=032b7000 CR4=00000690
    ...

The page directory is sane:

    (gdb) x/4wx 0x32b7000
    0x32b7000:	0x03398063	0x03399063	0x0339a063	0x0339b063
    (gdb) x/4wx 0x3398000
    0x3398000:	0x00000163	0x00001163	0x00002163	0x00003163
    (gdb) x/4wx 0x3399000
    0x3399000:	0x00400003	0x00401003	0x00402003	0x00403003

but our particular page directory entry is empty:

    (gdb) x/1wx 0x32b7000 + (0x724e000 >> 22) * 4
    0x32b7070:	0x00000000

[ It appears that you can skate past this issue if you don't receive
  any interrupts while the bogus GDT pointer is loaded, or if you avoid
  reloading the segment registers in general.

  Andy Lutomirski provides some additional insight:

   "AFAICT it's entirely permissible for the GDTR and/or LDT
    descriptor to point to unmapped memory.  Any attempt to use them
    (segment loads, interrupts, IRET, etc) will try to access that memory
    as if the access came from CPL 0 and, if the access fails, will
    generate a valid page fault with CR2 pointing into the GDT or
    LDT."

  Up until commit 23a0d4e8 ("efi: Disable interrupts around EFI
  calls, not in the epilog/prolog calls") interrupts were disabled
  around the prolog and epilog calls, and the functional GDT was
  re-installed before interrupts were re-enabled.

  Which explains why no one has hit this issue until now. ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: Laszlo Ersek <lersek@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ Updated changelog. ]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 696d8b70 upstream.

In case when the interrupt happened for the second eDMA the channel
number was incorrectly passed to the client driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 7e312103 upstream.

IOMMU-based dma_mmap() implementation lacked proper support for offset
parameter used in mmap call (it always assumed that mapping starts from
offset zero). This patch adds support for offset parameter to IOMMU-based
implementation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>

commit 371f0f08 upstream.

dma_mmap() function in IOMMU-based dma-mapping implementation lacked
a check for valid range of mmap parameters (offset and buffer size), what
might have caused access beyond the allocated buffer. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>