Create the dts files for each core and splits the devices between the two
cores for P1020RDB.

Core0 has core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb, eth1,
eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
Core1 has l2, eth0, crypto.

MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.

Fix compatible property for global-util node of P1020si.dtsi.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

PCIe device in legacy mode can trigger interrupts using the wires #INTA,
#INTB ,#INTC and #INTD. PCI devices are obligated to use #INTx for
interrupts under legacy mode.  Each PCI slot or device is typically wired
to different inputs on the interrupt controller.

So, Define interrupt-map and interrupt-map-mask properties for device tree
to of map each PCI interrupt signal to the inputs of the interrupt
controller.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Creates P2020si.dtsi, containing information for P2020 SoC. Modifies dts
files for P2020 based systems to use dtsi file.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Creates P1020si.dtsi, containing information for the P1020 SoC. Modifies dts
files for P1020 based systems to use dtsi file
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Grant Likely <grant.likelY@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Bhaskar Upadhaya <bhaskar.upadhaya@freescale.com>
Acked-By: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This debug option has no overhead other than a slight increase in
kernel size, and makes bug reports more useful.  While some end users
may prefer to save the space, as a default on a kernel config aimed
primarily at development on reference boards, it should be enabled.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Even though support for the p5020's on-chip ethernet is not yet upstream,
it is not appropriate to disable all networking support (including
loopback, unix domain sockets, external ethernet devices, etc) in the
defconfig.  The networking settings are taken from mpc85xx_smp_defconfig,
minus the drivers for ethernet devices not found on any current e5500
chip.

The other changes are the result of running "make savedefconfig".
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add support for MPIC timers as requestable interrupt sources.

Based on http://patchwork.ozlabs.org/patch/20941/ by Dave Liu.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

There is no hardware interrupt 0xf7.  But now we can express the timer
interrupt using 4-cell interrupts.  This requires converting all of the
other interrupt specifiers in the tree as well.

Also add the second timer group, and fix the reg property to only
describe the timer registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Update the existing example in the general mpic binding to have a
separate TCRx region.  Currently the example doesn't describe TCRx at
all.  The one upstream device tree with an mpic timer node (p1022ds)
uses one large reg region to describe both, even though there are other
unrelated registers in between.  That device tree also contains a bogus
interrupt specifier, and there's no upstream software that uses this yet,
so changing this shouldn't be a problem.

Add a full binding for the MPIC timer node, not just an example of
4-cell interrupts in the MPIC binding.

Add fsl,available-ranges, similar to msi-available-ranges.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

If the video mode is set to 16-, 24-, or 32-bit pixels, then the pixel data
contains actual levels of red, blue, and green.  However, if the video mode
is set to 8-bit pixels, then the 8-bit value represents an index into color
table.  This is called "palette mode" on the Freescale DIU video controller.

The DIU driver does not currently support palette mode, but the MPC8610 HPCD
board file returned a non-zero (although incorrect) pixel format value for
8-bit mode.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

It may trigger a warning in fs/proc/generic.c:__xlate_proc_name() when
trying to add an entry for the interrupt handler to sysfs.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Without this, we attempt to use doorbells for IPIs, and end up
branching to some bad address.  Plus, even for the exceptions
we don't implement, it's good to handle it and get a message out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

commit c56e5853 breaks SMP support in PPC_47x chip.
 secondary_ti must be set to current thread info before callin kick_cpu or else
 start_secondary_47x will jump into void when trying to return to c-code.
 In the current setup secondary_ti is initialized before the CPU idle task is started
 and only the boot core will start. I am not sure this is the correct solution, but it
 makes SMP possible in my chip.
 Note! The HOTPLUG support probably need some fixing to, There is no trampoline code
 available in head_44x.S - start_secondary_resume?
Signed-off-by: Kerstin Jonsson <kerstin.jonsson@ericsson.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Commit b987812b left
crash_kexec_wait_realmode() undefined for UP.

Commit 7c7a81b5 defined it for UP but
left it undefined for 32-bit SMP.

Seems like people are getting confused by nested #ifdef's, so move the
definitions of crash_kexec_wait_realmode() after the #ifdef CONFIG_SMP
section.

Compile-tested with 32-bit UP, 32-bit SMP and 64-bit SMP configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This should fix SMP & Hotplug builds on FSL BookE and 476
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
  drivercore: revert addition of of_match to struct device
  of: fix race when matching drivers

* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Kludge IP27 build for 2.6.39.
  MIPS: AR7: Fix GPIO register size for Titan variant.
  MIPS: Fix duplicate invocation of notify_die.
  MIPS: RB532: Fix iomap resource size miscalculation.

Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time.  This was unsafe
because matching is not an atomic operation with probing a driver.  If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.

This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

If two drivers are probing devices at the same time, both will write
their match table result to the dev->of_match cache at the same time.

Only write the result if the device matches.

In a thread titled "SBus devices sometimes detected, sometimes not",
Meelis reported his SBus hme was not detected about 50% of the time.
From the debug suggested by Grant it was obvious another driver matched
some devices between the call to match the hme and the hme discovery
failling.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Milton Miller <miltonm@bga.com>
[grant.likely: modified to only call of_match_device() once]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  block: don't delay blk_run_queue_async
  scsi: remove performance regression due to async queue run
  blk-throttle: Use task_subsys_state() to determine a task's blkio_cgroup
  block: rescan partitions on invalidated devices on -ENOMEDIA too
  cdrom: always check_disk_change() on open
  block: unexport DISK_EVENT_MEDIA_CHANGE for legacy/fringe drivers

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The 'size' variable contains the correct register size for both AR7
and Titan, but we never used it to ioremap the correct register size.
This problem only shows up on Titan.

[ralf@linux-mips.org: Fixed the fix.  The original patch as in patchwork
recognizes the problem correctly then fails to fix it ...]
Reported-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2380/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Initial patch by Yury Polyanskiy <ypolyans@princeton.edu>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2373/

This is the MIPS portion of Joe Perches <joe@perches.com>'s
https://patchwork.linux-mips.org/patch/2172/ which seems to have been
lost in time and space.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Let's check a scenario:
1. blk_delay_queue(q, SCSI_QUEUE_DELAY);
2. blk_run_queue_async();
the second one will became a noop, because q->delay_work already has
WORK_STRUCT_PENDING_BIT set, so the delayed work will still run after
SCSI_QUEUE_DELAY. But blk_run_queue_async actually hopes the delayed
work runs immediately.

Fix this by doing a cancel on potentially pending delayed work
before queuing an immediate run of the workqueue.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] V4L: soc-camera: regression fix: calculate .sizeimage in soc_camera.c
  [media] v4l2-subdev: fix broken subdev control enumeration
  [media] Fix cx88 remote control input
  [media] v4l: Release module if subdev registration fails

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, AMD: Fix ARAT feature setting again
  Revert "x86, AMD: Fix APIC timer erratum 400 affecting K8 Rev.A-E processors"
  x86, apic: Fix spurious error interrupts triggering on all non-boot APs
  x86, mce, AMD: Fix leaving freed data in a list
  x86: Fix UV BAU for non-consecutive nasids
  x86, UV: Fix NMI handler for UV platforms

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf evlist: Fix per thread mmap setup
  perf tools: Honour the cpu list parameter when also monitoring a thread list
  kprobes, x86: Disable irqs during optimized callback

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix cifsConvertToUCS() for the mapchars case
  cifs: add fallback in is_path_accessible for old servers

Provide a stub for proc_mkdir_mode() when CONFIG_PROC_FS is not
enabled, just like the stub for proc_mkdir().

Fixes this linux-next build error:

  drivers/net/wireless/airo.c:4504: error: implicit declaration of function 'proc_mkdir_mode'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

os_dump_core() uses abort() to terminate UML in case of an fatal error.

glibc's abort() calls raise(SIGABRT) which makes use of tgkill().
tgkill() has no effect within UML's kernel threads because they are not
pthreads.  As fallback abort() executes an invalid instruction to
terminate the process.  Therefore UML gets killed by SIGSEGV and leaves a
ugly log entry in the host's kernel ring buffer.

To get rid of this we use our own abort routine.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ZONE_CONGESTED should be a state of global memory reclaim.  If not, a busy
memcg sets this and give unnecessary throttoling in wait_iff_congested()
against memory recalim in other contexts.  This makes system performance
bad.

I'll think about "memcg is congested!" flag is required or not, later.
But this fix is required first.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Adding the necessary MODULE_DEVICE_TABLE() information allows the driver
to be automatically loaded by udev.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix switch initialization to ensure that all switches have default routing
disabled.  This guarantees that no unexpected RapidIO packets arrive to
the default port set by reset and there is no default routing destination
until it is properly configured by software.

This update also unifies handling of unmapped destinations by tsi57x, IDT
Gen1 and IDT Gen2 switches.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: <stable@kernel.org>		[2.6.37+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As Metze pointed out, commit 84cdf74e broke mapchars option:

    Commit "cifs: fix unaligned accesses in cifsConvertToUCS"
    (84cdf74e) does multiple steps
    in just one commit (moving the function and changing it without
    testing).

    put_unaligned_le16(temp, &target[j]); is never called for any
    codepoint the goes via the 'default' switch statement. As a result
    we put just zero (or maybe uninitialized) bytes into the target
    buffer.

His proposed patch looks correct, but doesn't apply to the current head
of the tree. This patch should also fix it.

Cc: <stable@kernel.org> # .38.x: 581ade4d: cifs: clean up various nits in unicode routines (try #2)
Reported-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

The is_path_accessible check uses a QPathInfo call, which isn't
supported by ancient win9x era servers. Fall back to an older
SMBQueryInfo call if it fails with the magic error codes.

Cc: stable@kernel.org
Reported-and-Tested-by: Sandro Bonazzola <sandro.bonazzola@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>