Pull pinctrl fix from Linus Walleij:
 "A single last pin control fix for v4.6.  t's tagged for stable and
  only hits a single driver with two added lines so should be safe.
  Tested in linux-next.

   - The pull up/down logic for the AT91 PIO4 controller was tilted: we
     need to mask the reverse pull when unmasking a pull direction.

     Setting both pull up & pull down is illegal and makes no sense"

* tag 'pinctrl-v4.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: at91-pio4: fix pull-up/down logic

Pull SCSI fixes from James Bottomley:
 "This is a couple of small fixes: one is a potential uninitialised
  error variable in the alua code, potentially causing spurious failures
  and the other is a problem caused by the conversion of SCSI to
  hostwide tags which resulted in the qla1280 driver always failing in
  host initialisation"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  qla1280: Don't allocate 512kb of host tags
  scsi_dh_alua: uninitialized variable in alua_rtpg()

Pull networking fixes from David Miller:
 "Hopefully the last round of fixes this release, fingers crossed :)

   1) Initialize static nf_conntrack_locks_all_lock properly, from
      Florian Westphal.

   2) Need to cancel pending work when destroying IDLETIMER entries,
      from Liping Zhang.

   3) Fix TX param usage when sending TSO over iwlwifi devices, from
      Emmanuel Grumbach.

   4) NFACCT quota params not validated properly, from Phil Turnbull.

   5) Resolve more glibc vs.  kernel header conflicts, from Mikko
      Tapeli.

   6) Missing IRQ free in ravb_close(), from Geert Uytterhoeven.

   7) Fix infoleak in x25, from Kangjie Lu.

   8) Similarly in thunderx driver, from Heinrich Schuchardt.

   9) tc_ife.h uapi header not exported properly, from Jamal Hadi Salim.

  10) Don't reenable PHY interreupts if device is in polling mode, from
      Shaohui Xie.

  11) Packet scheduler actions late binding was not being handled
      properly at all, from Jamal Hadi Salim.

  12) Fix binding of conntrack entries to helpers in openvswitch, from
      Joe Stringer"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (21 commits)
  gre: do not keep the GRE header around in collect medata mode
  openvswitch: Fix cached ct with helper.
  net sched: ife action fix late binding
  net sched: skbedit action fix late binding
  net sched: simple action fix late binding
  net sched: mirred action fix late binding
  net sched: ipt action fix late binding
  net sched: vlan action fix late binding
  net: phylib: fix interrupts re-enablement in phy_start
  tcp: refresh skb timestamp at retransmit time
  net: nps_enet: bug fix - handle lost tx interrupts
  net: nps_enet: Tx handler synchronization
  export tc ife uapi header
  net: thunderx: avoid exposing kernel stack
  net: fix a kernel infoleak in x25 module
  ravb: Add missing free_irq() call to ravb_close()
  uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h
  netfilter: nfnetlink_acct: validate NFACCT_QUOTA parameter
  iwlwifi: mvm: don't override the rate with the AMSDU len
  netfilter: IDLETIMER: fix race condition when destroy the target
  ...

For ipgre interface in collect metadata mode, it doesn't make sense for the
interface to be of ARPHRD_IPGRE type. The outer header of received packets
is not needed, as all the information from it is present in metadata_dst. We
already don't set ipgre_header_ops for collect metadata interfaces, which is
the only consumer of mac_header pointing to the outer IP header.

Just set the interface type to ARPHRD_NONE in collect metadata mode for
ipgre (not gretap, that still correctly stays ARPHRD_ETHER) and reset
mac_header.

Fixes: a64b04d8 ("gre: do not assign header_ops in collect metadata mode")
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using conntrack helpers from OVS, a common configuration is to
perform a lookup without specifying a helper, then go through a
firewalling policy, only to decide to attach a helper afterwards.

In this case, the initial lookup will cause a ct entry to be attached to
the skb, then the later commit with helper should attach the helper and
confirm the connection. However, the helper attachment has been missing.
If the user has enabled automatic helper attachment, then this issue
will be masked as it will be applied in init_conntrack(). It is also
masked if the action is executed from ovs_packet_cmd_execute() as that
will construct a fresh skb.

This patch fixes the issue by making an explicit call to try to assign
the helper if there is a discrepancy between the action's helper and the
current skb->nfct.

Fixes: cae3a262 ("openvswitch: Allow attaching helpers to ct action")
Signed-off-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The x86 exception table sorting was changed in commit 29934b0f
("x86/extable: use generic search and sort routines") to use the arch
independent code in lib/extable.c.  However, the patch was mangled
somehow on its way into the kernel from the last version posted at [1].
The committed version kind of attempted to incorporate the changes of
commit 548acf19 ("x86/mm: Expand the exception table logic to allow
new handling options") as in _completely_ _ignoring_ the x86 specific
'handler' member of struct exception_table_entry.  This effectively
broke the sorting as entries will only partly be swapped now.

Fortunately, the x86 Kconfig selects BUILDTIME_EXTABLE_SORT, so the
exception table doesn't need to be sorted at runtime. However, in case
that ever changes, we better not break the exception table sorting just
because of that.

[ Ard Biesheuvel points out that BUILDTIME_EXTABLE_SORT applies to the
  core image only, but we still rely on the sorting routines for modules
  in that case - Linus ]

Fix this by providing a swap_ex_entry_fixup() macro that takes care of
the 'handler' member.

[1] https://lkml.org/lkml/2016/1/27/232Signed-off-by: Mathias Krause <minipli@googlemail.com>
Fixes: 29934b0f ("x86/extable: use generic search and sort routines")
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi fixes from Mark Brown:
 "A bunch of small driver specific fixes that have come up, none of them
  remarkable in themselves.  One fixes a regression introduced in the
  merge window and another two are targetted at stable"

* tag 'spi-fix-v4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: pxa2xx: Do not detect number of enabled chip selects on Intel SPT
  spi: spi-ti-qspi: Handle truncated frames properly
  spi: spi-ti-qspi: Fix FLEN and WLEN settings if bits_per_word is overridden
  spi: omap2-mcspi: Undo broken fix for dma transfer of vmalloced buffer
  spi: spi-fsl-dspi: Fix cs_change handling in message transfer

Pull KVM fixes from Paolo Bonzini:
 "Two small x86 patches, improving "make kvmconfig" and fixing an
  objtool warning for CONFIG_PROFILE_ALL_BRANCHES"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  kvmconfig: add more virtio drivers
  x86/kvm: Add stack frame dependency to fastop() inline asm

Jamal Hadi Salim says:

====================
Some actions were broken in allowing for late binding of actions.
Late binding workflow is as follows:
a) create an action and provide all necessary parameters for it
Optionally provide an index or let the kernel give you one.
Example:
sudo tc actions add action police rate 1kbit burst 90k drop index 1

b) later on bind to the pre-created action from a filter definition
by merely specifying the index.
Example:
sudo tc filter add dev lo parent ffff: protocol ip prio 8 \
u32 match ip src 127.0.0.8/32 flowid 1:8 action police index 1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The process below was broken and is fixed with this patch.

//add an ife action and give it an instance id of 1
sudo tc actions add action ife encode \
type 0xDEAD allow mark dst 02:15:15:15:15:15 index 1

//create a filter which binds to ife action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:11 action ife index 1

Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The process below was broken and is fixed with this patch.

//add a skbedit action and give it an instance id of 1
sudo tc actions add action skbedit mark 10 index 1
//create a filter which binds to skbedit action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action skbedit index 1

Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The process below was broken and is fixed with this patch.

//add a simple action and give it an instance id of 1
sudo tc actions add action simple sdata "foobar" index 1
//create a filter which binds to simple action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action simple index 1

Message before fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The process below was broken and is fixed with this patch.

//add an mirred action and give it an instance id of 1
sudo tc actions add action mirred egress mirror dev $MDEV  index 1
//create a filter which binds to mirred action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action mirred index 1

Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was broken and is fixed with this patch.

//add an ipt action and give it an instance id of 1
sudo tc actions add action ipt -j mark --set-mark 2 index 1
//create a filter which binds to ipt action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32\
match ip dst 17.0.0.1/32 flowid 1:10 action ipt index 1

Message before bug fix was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Late vlan action binding was broken and is fixed with this patch.

//add a vlan action to pop and give it an instance id of 1
sudo tc actions add action vlan pop index 1
//create filter which binds to vlan action id 1
sudo tc filter add dev $DEV parent ffff: protocol ip prio 1 u32 \
match ip dst 17.0.0.1/32 flowid 1:1 action vlan index 1

current message(before bug fix) was:
RTNETLINK answers: Invalid argument
We have an error talking to the kernel
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If phy was suspended and is starting, current driver always enable
phy's interrupts, if phy works in polling, phy can raise unexpected
interrupt which will not be handled, the interrupt will block system
enter suspend again. So interrupts should only be re-enabled if phy
works in interrupt.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the very unlikely case __tcp_retransmit_skb() can not use the cloning
done in tcp_transmit_skb(), we need to refresh skb_mstamp before doing
the copy and transmit, otherwise TCP TS val will be an exact copy of
original transmit.

Fixes: 7faee5c0 ("tcp: remove TCP_SKB_CB(skb)->when")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Elad Kanfi says:

====================
nps_enet: Net driver bugs fix

v3:
tx_packet_sent flag is not necessary, use socket buffer pointer
instead.
Use wmb() instead of smp_wmb().

v2:
Remove code style commit for now.
Code style commit will be added after the bugs fix will be approved.

Summary:
 1. Bug description: TX done interrupts that arrives while interrupts
    are masked, during NAPI poll, will not trigger an interrupt handling.
    Since TX interrupt is of level edge we will lose the TX done interrupt.
    As a result all pending tx frames will get no service.

    Solution: Check if there is a pending tx request after unmasking the
    interrupt and if answer is yes then re-add ourselves to
    the NAPI poll list.

 2. Bug description: CPU-A before sending a frame will set a variable
    to true. CPU-B that executes the tx done interrupt service routine
    might read a non valid value of that variable.

    Solution: Use the socket buffer pointer instead of the variable,
    and add a write memory barrier at the tx sending function after
    the pointer is set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The tx interrupt is of edge type, and in case such interrupt is triggered
while it is masked it will not be handled even after tx interrupts are
re-enabled in the end of NAPI poll.
This will cause tx network to stop in the following scenario:
 * Rx is being handled, hence interrupts are masked.
 * Tx interrupt is triggered after checking if there is some tx to handle
   and before re-enabling the interrupts.
In this situation only rx transaction will release tx requests.

In order to handle the tx that was missed( if there was one ),
a NAPI reschdule was added after enabling the interrupts.
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Below is a description of a possible problematic
sequence. CPU-A is sending a frame and CPU-B handles
the interrupt that indicates the frame was sent. CPU-B
reads an invalid value of tx_packet_sent.

	CPU-A				CPU-B
	-----				-----
	nps_enet_send_frame
	.
	.
	tx_skb = skb
	tx_packet_sent = true
	order HW to start tx
	.
	.
	HW complete tx
			    ------> 	get tx complete interrupt
					.
					.
					if(tx_packet_sent == true)
						handle tx_skb

	end memory transaction
	(tx_packet_sent actually
	 written)

Furthermore there is a dependency between tx_skb and tx_packet_sent.
There is no assurance that tx_skb contains a valid pointer at CPU B
when it sees tx_packet_sent == true.

Solution:

Initialize tx_skb to NULL and use it to indicate that packet was sent,
in this way tx_packet_sent can be removed.
Add a write memory barrier after setting tx_skb in order to make sure
that it is valid before HW is informed and IRQ is fired.

Fixed sequence will be:

       CPU-A                           CPU-B
       -----                           -----

	tx_skb = skb
	wmb()
	.
	.
	order HW to start tx
	.
	.
	HW complete tx
			------>		get tx complete interrupt
					.
					.
					if(tx_skb != NULL)
						handle tx_skb

					tx_skb = NULL
Signed-off-by: Elad Kanfi <eladkan@mellanox.com>
Acked-by: Noam Camus <noamca@mellanox.com>
Acked-by: Gilad Ben-Yossef <giladby@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull PCI fixes from Bjorn Helgaas:
 "Since v4.5, we've WARNed during resume if a PCI device, including a
  Thunderbolt device, was added while we were suspended.  A change we
  merged for v4.6-rc1 turned that warning into a system hang.  These
  enumeration patches from Lukas Wunner fix this issue:

   - Fix BUG on device attach failure
   - Do not treat EPROBE_DEFER as device attach failure"

* tag 'pci-v4.6-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Do not treat EPROBE_DEFER as device attach failure
  PCI: Fix BUG on device attach failure

Pull x86 fixes from Ingo Molnar:
 "Two topology corner case fixes, and a MAINTAINERS file update for
  mmiotrace maintenance"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/topology: Set x86_max_cores to 1 for CONFIG_SMP=n
  MAINTAINERS: Add mmiotrace entry
  x86/topology: Handle CPUID bogosity gracefully

Pull scheduler fixes from Ingo Molnar:
 "A UP kernel cpufreq fix and a rt/dl scheduler corner case fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/rt, sched/dl: Don't push if task's scheduling class was changed
  sched/fair: Fix !CONFIG_SMP kernel cpufreq governor breakage

"make defconfig kvmconfig" is supposed to end up with usable kernel for
KVM guest. In practice, it won't work for e.g. Hetzner VPS (KVM-based)
unless you add these options.
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

The kbuild test robot reported this objtool warning [1]:

  arch/x86/kvm/emulate.o: warning: objtool: fastop()+0x69: call without frame pointer save/setup

The issue seems to be caused by CONFIG_PROFILE_ALL_BRANCHES.  With that
option, for some reason gcc decides not to create a stack frame in
fastop() before doing the inline asm call, which can result in a bad
stack trace.

Force a stack frame to be created if CONFIG_FRAME_POINTER is enabled by
listing the stack pointer as an output operand for the inline asm
statement.

This change has no effect for !CONFIG_PROFILE_ALL_BRANCHES.

[1] https://lists.01.org/pipermail/kbuild-all/2016-March/018249.htmlReported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

We got this warning:

    WARNING: CPU: 1 PID: 2468 at kernel/sched/core.c:1161 set_task_cpu+0x1af/0x1c0
    [...]
    Call Trace:

    dump_stack+0x63/0x87
    __warn+0xd1/0xf0
    warn_slowpath_null+0x1d/0x20
    set_task_cpu+0x1af/0x1c0
    push_dl_task.part.34+0xea/0x180
    push_dl_tasks+0x17/0x30
    __balance_callback+0x45/0x5c
    __sched_setscheduler+0x906/0xb90
    SyS_sched_setattr+0x150/0x190
    do_syscall_64+0x62/0x110
    entry_SYSCALL64_slow_path+0x25/0x25

This corresponds to:

    WARN_ON_ONCE(p->state == TASK_RUNNING &&
             p->sched_class == &fair_sched_class &&
             (p->on_rq && !task_on_rq_migrating(p)))

It happens because in find_lock_later_rq(), the task whose scheduling
class was changed to fair class is still pushed away as if it were
a deadline task ...

So, check in find_lock_later_rq() after double_lock_balance(), if the
scheduling class of the deadline task was changed, break and retry.

Apply the same logic to RT tasks.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Link: http://lkml.kernel.org/r/1462767091-1215-1-git-send-email-xlpang@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Josef reported that the uncore driver trips over with CONFIG_SMP=n because
x86_max_cores is 16 instead of 12.

The reason is, that for SMP=n the extended topology detection is a NOOP and
the cache leaf is used to determine the number of cores. That's wrong in two
aspects:

1) The cache leaf enumerates the maximum addressable number of cores in the
   package, which is obviously not correct

2) UP has no business with topology bits at all.

Make intel_num_cpu_cores() return 1 for CONFIG_SMP=n
Reported-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team <Kernel-team@fb.com>
Cc: Kan Liang <kan.liang@intel.com>
Link: http://lkml.kernel.org/r/761b4a2a-0332-7954-f030-c6639f949612@fb.com

Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2016-05-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.6

iwlwifi

* fix P2P rates (and possibly other issues)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contain Netfilter simple fixes for your net tree,
two one-liner and one two-liner:

1) Oneliner to fix missing spinlock definition that triggers
   'BUG: spinlock bad magic on CPU#' when spinlock debugging is enabled,
   from Florian Westphal.

2) Fix missing workqueue cancelation on IDLETIMER removal,
   from Liping Zhang.

3) Fix insufficient validation of netlink of NFACCT_QUOTA in
   nfnetlink_acct, from Phil Turnbull.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Reserved fields should be set to zero to avoid exposing
bits from the kernel stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stack object "dte_facilities" is allocated in x25_rx_call_request(),
which is supposed to be initialized in x25_negotiate_facilities.
However, 5 fields (8 bytes in total) are not initialized. This
object is then copied to userland via copy_to_user, thus infoleak
occurs.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:

    IP-Config: Reopening network devices...
    genirq: Flags mismatch irq 139. 00000000 (eth0:ch24:emac) vs. 00000000 (eth0:ch24:emac)
    ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch24:emac
    IP-Config: Failed to open eth0
    IP-Config: No network devices available

The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.

However, the real cause is that ravb_close() doesn't release the R-Car
Gen3-specific secondary IRQ.

Add the missing free_irq() call to fix this.

Fixes: 22d4df8f ("ravb: Add support for r8a7795 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

glibc's net/if.h contains copies of definitions from linux/if.h and these
conflict and cause build failures if both files are included by application
source code. Changes in uapi headers, which fixed header file dependencies to
include linux/if.h when it was needed, e.g. commit 1ffad83d, made the
net/if.h and linux/if.h incompatibilities visible as build failures for
userspace applications like iproute2 and xtables-addons.

This patch fixes compile errors when glibc net/if.h is included before
linux/if.h:

./linux/if.h:99:21: error: redeclaration of enumerator ‘IFF_NOARP’
./linux/if.h:98:23: error: redeclaration of enumerator ‘IFF_RUNNING’
./linux/if.h:97:26: error: redeclaration of enumerator ‘IFF_NOTRAILERS’
./linux/if.h:96:27: error: redeclaration of enumerator ‘IFF_POINTOPOINT’
./linux/if.h:95:24: error: redeclaration of enumerator ‘IFF_LOOPBACK’
./linux/if.h:94:21: error: redeclaration of enumerator ‘IFF_DEBUG’
./linux/if.h:93:25: error: redeclaration of enumerator ‘IFF_BROADCAST’
./linux/if.h:92:19: error: redeclaration of enumerator ‘IFF_UP’
./linux/if.h:252:8: error: redefinition of ‘struct ifconf’
./linux/if.h:203:8: error: redefinition of ‘struct ifreq’
./linux/if.h:169:8: error: redefinition of ‘struct ifmap’
./linux/if.h:107:23: error: redeclaration of enumerator ‘IFF_DYNAMIC’
./linux/if.h:106:25: error: redeclaration of enumerator ‘IFF_AUTOMEDIA’
./linux/if.h:105:23: error: redeclaration of enumerator ‘IFF_PORTSEL’
./linux/if.h:104:25: error: redeclaration of enumerator ‘IFF_MULTICAST’
./linux/if.h:103:21: error: redeclaration of enumerator ‘IFF_SLAVE’
./linux/if.h:102:22: error: redeclaration of enumerator ‘IFF_MASTER’
./linux/if.h:101:24: error: redeclaration of enumerator ‘IFF_ALLMULTI’
./linux/if.h:100:23: error: redeclaration of enumerator ‘IFF_PROMISC’

The cases where linux/if.h is included before net/if.h need a similar fix in
the glibc side, or the order of include files can be changed userspace
code as a workaround.

This change was tested in x86 userspace on Debian unstable with
scripts/headers_compile_test.sh:

$ make headers_install && \
  cd usr/include && ../../scripts/headers_compile_test.sh -l -k
...
cc -Wall -c -nostdinc -I /usr/lib/gcc/i586-linux-gnu/5/include -I /usr/lib/gcc/i586-linux-gnu/5/include-fixed -I . -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH -I /home/mcfrisk/src/linux-2.6/usr/headers_compile_test_include.2uX2zH/i586-linux-gnu -o /dev/null ./linux/if.h_libc_before_kernel.h
PASSED libc before kernel test: ./linux/if.h
Reported-by: Jan Engelhardt <jengelh@inai.de>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Stephen Hemminger <shemming@brocade.com>
Reported-by: Waldemar Brodkorb <mail@waldemar-brodkorb.de>
Cc: Gabriel Laskar <gabriel@lse.epita.fr>
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm build fix from Dan Williams:
 "A build fix for the usage of HPAGE_SIZE in the last libnvdimm pull
  request.

  I have taken note that the kbuild robot build success test does not
  include results for alpha_allmodconfig.  Thanks to Guenter for the
  report.  It's tagged for -stable since the original fix will land
  there and cause build problems"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm, pfn: fix ARCH=alpha allmodconfig build failure

Allowing unprivileged kernel profiling lets any user dump follow kernel
control flow and dump kernel registers.  This most likely allows trivial
kASLR bypassing, and it may allow other mischief as well.  (Off the top
of my head, the PERF_SAMPLE_REGS_INTR output during /dev/urandom reads
could be quite interesting.)
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge fixes from Andrew Morton:
 "2 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  zsmalloc: fix zs_can_compact() integer overflow
  Revert "proc/base: make prompt shell start from new line after executing "cat /proc/$pid/wchan""

zs_can_compact() has two race conditions in its core calculation:

unsigned long obj_wasted = zs_stat_get(class, OBJ_ALLOCATED) -
				zs_stat_get(class, OBJ_USED);

1) classes are not locked, so the numbers of allocated and used
   objects can change by the concurrent ops happening on other CPUs
2) shrinker invokes it from preemptible context

Depending on the circumstances, thus, OBJ_ALLOCATED can become
less than OBJ_USED, which can result in either very high or
negative `total_scan' value calculated later in do_shrink_slab().

do_shrink_slab() has some logic to prevent those cases:

 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-64
 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62
 vmscan: shrink_slab: zs_shrinker_scan+0x0/0x28 [zsmalloc] negative objects to delete nr=-62

However, due to the way `total_scan' is calculated, not every
shrinker->count_objects() overflow can be spotted and handled.
To demonstrate the latter, I added some debugging code to do_shrink_slab()
(x86_64) and the results were:

 vmscan: OVERFLOW: shrinker->count_objects() == -1 [18446744073709551615]
 vmscan: but total_scan > 0: 92679974445502
 vmscan: resulting total_scan: 92679974445502
[..]
 vmscan: OVERFLOW: shrinker->count_objects() == -1 [18446744073709551615]
 vmscan: but total_scan > 0: 22634041808232578
 vmscan: resulting total_scan: 22634041808232578

Even though shrinker->count_objects() has returned an overflowed value,
the resulting `total_scan' is positive, and, what is more worrisome, it
is insanely huge. This value is getting used later on in
shrinker->scan_objects() loop:

        while (total_scan >= batch_size ||
               total_scan >= freeable) {
                unsigned long ret;
                unsigned long nr_to_scan = min(batch_size, total_scan);

                shrinkctl->nr_to_scan = nr_to_scan;
                ret = shrinker->scan_objects(shrinker, shrinkctl);
                if (ret == SHRINK_STOP)
                        break;
                freed += ret;

                count_vm_events(SLABS_SCANNED, nr_to_scan);
                total_scan -= nr_to_scan;

                cond_resched();
        }

`total_scan >= batch_size' is true for a very-very long time and
'total_scan >= freeable' is also true for quite some time, because
`freeable < 0' and `total_scan' is large enough, for example,
22634041808232578. The only break condition, in the given scheme of
things, is shrinker->scan_objects() == SHRINK_STOP test, which is a
bit too weak to rely on, especially in heavy zsmalloc-usage scenarios.

To fix the issue, take a pool stat snapshot and use it instead of
racy zs_stat_get() calls.

Link: http://lkml.kernel.org/r/20160509140052.3389-1-sergey.senozhatsky@gmail.comSigned-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org>        [4.3+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts the 4.6-rc1 commit 7e2bc81d ("proc/base: make prompt
shell start from new line after executing "cat /proc/$pid/wchan")
because it breaks /proc/$PID/whcan formatting in ps and top.

Revert also because the patch is inconsistent - it adds a newline at the
end of only the '0' wchan, and does not add a newline when
/proc/$PID/wchan contains a symbol name.

eg.
$ ps -eo pid,stat,wchan,comm
PID STAT WCHAN  COMMAND
...
1189 S    -      dbus-launch
1190 Ssl  0
dbus-daemon
1198 Sl   0
lightdm
1299 Ss   ep_pol systemd
1301 S    -      (sd-pam)
1304 Ss   wait   sh
Signed-off-by: Robin Humble <plaguedbypenguins@gmail.com>
Cc: Minfei Huang <mnfhuang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - bug in ahash SG list walking that may lead to crashes

   - resource leak in qat

   - missing RSA dependency that causes it to fail"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: rsa - select crypto mgr dependency
  crypto: hash - Fix page length clamping in hash walk
  crypto: qat - fix adf_ctl_drv.c:undefined reference to adf_init_pf_wq
  crypto: qat - fix invalid pf2vf_resp_wq logic