stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.

This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.

When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.

When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethoc_reset enables device interrupts, ethoc_interrupt may schedule a
NAPI poll before NAPI is enabled in the ethoc_open, which results in
device being unable to send or receive anything until it's closed and
reopened. In case the device is flooded with ingress packets it may be
unable to recover at all.
Move napi_enable above ethoc_reset in the ethoc_open to fix that.

Fixes: a1702857 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We might call br_afspec() with p == NULL which is a valid use case if
the action is on the bridge device itself, but the bridge tunnel code
dereferences the p pointer without checking, so check if p is null
first.
Reported-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Fixes: efa5356b ("bridge: per vlan dst_metadata netlink support")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit a47b70ea ("ravb: unmap descriptors when freeing rings") has
introduced the issue seen in [1] reproduced on H3ULCB board.

Fix this by relocating the RX skb ringbuffer free operation, so that
swiotlb page unmapping can be done first. Freeing of aligned TX buffers
is not relevant to the issue seen in [1]. Still, reposition TX free
calls as well, to have all kfree() operations performed consistently
_after_ dma_unmap_*()/dma_free_*().

[1] Console screenshot with the problem reproduced:

salvator-x login: root
root@salvator-x:~# ifconfig eth0 up
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: \
       attached PHY driver [Micrel KSZ9031 Gigabit PHY]   \
       (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=235)
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
root@salvator-x:~#
root@salvator-x:~# ifconfig eth0 down

==================================================================
BUG: KASAN: use-after-free in swiotlb_tbl_unmap_single+0xc4/0x35c
Write of size 1538 at addr ffff8006d884f780 by task ifconfig/1649

CPU: 0 PID: 1649 Comm: ifconfig Not tainted 4.12.0-rc4-00004-g112eb072 #32
Hardware name: Renesas H3ULCB board based on r8a7795 (DT)
Call trace:
[<ffff20000808f11c>] dump_backtrace+0x0/0x3a4
[<ffff20000808f4d4>] show_stack+0x14/0x1c
[<ffff20000865970c>] dump_stack+0xf8/0x150
[<ffff20000831f8b0>] print_address_description+0x7c/0x330
[<ffff200008320010>] kasan_report+0x2e0/0x2f4
[<ffff20000831eac0>] check_memory_region+0x20/0x14c
[<ffff20000831f054>] memcpy+0x48/0x68
[<ffff20000869ed50>] swiotlb_tbl_unmap_single+0xc4/0x35c
[<ffff20000869fcf4>] unmap_single+0x90/0xa4
[<ffff20000869fd14>] swiotlb_unmap_page+0xc/0x14
[<ffff2000080a2974>] __swiotlb_unmap_page+0xcc/0xe4
[<ffff2000088acdb8>] ravb_ring_free+0x514/0x870
[<ffff2000088b25dc>] ravb_close+0x288/0x36c
[<ffff200008aaf8c4>] __dev_close_many+0x14c/0x174
[<ffff200008aaf9b4>] __dev_close+0xc8/0x144
[<ffff200008ac2100>] __dev_change_flags+0xd8/0x194
[<ffff200008ac221c>] dev_change_flags+0x60/0xb0
[<ffff200008ba2dec>] devinet_ioctl+0x484/0x9d4
[<ffff200008ba7b78>] inet_ioctl+0x190/0x194
[<ffff200008a78c44>] sock_do_ioctl+0x78/0xa8
[<ffff200008a7a128>] sock_ioctl+0x110/0x3c4
[<ffff200008365a70>] vfs_ioctl+0x90/0xa0
[<ffff200008365dbc>] do_vfs_ioctl+0x148/0xc38
[<ffff2000083668f0>] SyS_ioctl+0x44/0x74
[<ffff200008083770>] el0_svc_naked+0x24/0x28

The buggy address belongs to the page:
page:ffff7e001b6213c0 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: 0000000000000000 ffff7e001b6213e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff8006d884f680: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
 ffff8006d884f700: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff8006d884f780: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
                   ^
 ffff8006d884f800: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
 ffff8006d884f880: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
==================================================================
Disabling lock debugging due to kernel taint
root@salvator-x:~#

Fixes: a47b70ea ("ravb: unmap descriptors when freeing rings")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When using CALIPSO with IPPROTO_UDP it is possible to trigger a GPF as the
IP header may have moved.

Also update the payload length after adding the CALIPSO option.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.

Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-06-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.12

It has been a slow start of cycle and this the first set of fixes for
4.12. Nothing really major here.

wcn36xx

* fix an issue with module reload

brcmfmac

* fix aligment regression on 64 bit systems

iwlwifi

* fixes for memory leaks, runtime PM, memory initialisation and other
  smaller problems

* fix IBSS on devices using DQA mode (7260 and up)

* fix the minimum firmware API requirement for 7265D, 3168, 8000 and
  8265
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2017-06-06

This series contains fixes to i40e and i40evf only.

Mauro S. M. Rodrigues fixes a flood in the kernel log which was introduced
in a previous commit because of a mistaken substitution of __I40E_VSI_DOWN
instead of __I40E_DOWN when testing the state of the PF.

Björn Töpel fixes an issue introduced in a previous commit where the
offset was incorrect and could lead to data corruption for architectures
using PAGE_SIZE larger than 8191.  Fixed the issue by updating the
page_offset correctly using the proper setting for truesize.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit b699d003.

As per Eric Dumazet, the pskb_may_pull() is a NOP in this
particular case, so the 'iph' reload is unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>

In f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.

Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.

Fixes: f8b45b74 ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:

[49.013] i40e 0002:01:00.0: bad reset request 0x00000020

Commit d19cb64b ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.

This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.

Fixes: 0da36b97 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Merge tag 'iwlwifi-for-kalle-2017-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Fixes for 4.12:

* Some memory leaks;
* IBSS support;
* Some bugzilla bugs;
* Some runtime PM fixes;
* Rate-scaling issues;
* Some locking problems;

Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In a previous commit, we removed support for API versions earlier than
22 for these NICs.  By mistake, the *_UCODE_API_MIN definitions were
set to 17.  Fix that.

Fixes: 4b87e5af ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore.  Mistakenly, this was changed to return an
error while fixing another bug.

If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.

Fixes: cd4d23c1 ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.

Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
  recording)

For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.

Fixes: 5c89e7bc ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.

Fixes: 7948b873 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

During d0i3 flow we flush all the queue except from the command queue.
Currently, in this flow the command queue is hard coded to 9.
In DQA the command queue number has changed from 9 to 0.
Fix that.

This fixes a problem in runtime PM resume flow.

Fixes: 097129c9 ("iwlwifi: mvm: move cmd queue to be #0 in dqa mode")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Up until now, the driver was comparing the rate reported by the FW and
the rate of the latest LQ command to avoid processing data belonging
to the old LQ command. Recently, FW changed the meaning of the initial
rate field in tx response and it holds the actual rate (which is not
necessarily the initial rate of LQ's rate table). Use instead LQ cmd
color to be able to filter out tx responses/BA notifications which
where sent during earlier LQ commands' time frame.

This fixes some throughput degradation in noisy environments.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The Granular QoS per VF feature must be enabled in FW before it can be
used.

Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.

Fixes: 08068cd5 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kernel-doc warnings (typo) in drivers/net/phy/phy.c:

..//drivers/net/phy/phy.c:259: warning: No description found for parameter 'features'
..//drivers/net/phy/phy.c:259: warning: Excess function parameter 'feature' description in 'phy_lookup_setting'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

We must free allocated skb when genlmsg_put() return fails.

Fixes: 1555d204 ("devlink: Support for pipeline debug (dpipe)")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update tcp.txt to fix mandatory congestion control ops and default
CCA selection. Also, fix comment in tcp.h for undo_cwnd.
Signed-off-by: Anmol Sarma <me@anmolsarma.in>
Signed-off-by: David S. Miller <davem@davemloft.net>

Our previous patch (cited below) introduced a regression
for RAW Eth QPs.

Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.

Fixes: 89c55768 ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since iptunnel_pull_header() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head.

Fixes: a09a4c8d ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander reported various KASAN messages triggered in recent kernels

The problem is that ping sockets should not use udp_poll() in the first
place, and recent changes in UDP stack finally exposed this old bug.

Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Fixes: 6d0bfe22 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Solar Designer <solar@openwall.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Tested-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9520ed8f ("net: dsa: use cpu_switch instead of ds[0]")
replaced the use of dst->ds[0] with dst->cpu_switch since that is
functionally equivalent, however, we can now run into an use after free
scenario after unbinding then rebinding the switch driver.

The use after free happens because we do correctly initialize
dst->cpu_switch the first time we probe in dsa_cpu_parse(), then we
unbind the driver: dsa_dst_unapply() is called, and we rebind again.
dst->cpu_switch now points to a freed "ds" structure, and so when we
finally dereference it in dsa_cpu_port_ethtool_setup(), we oops.

To fix this, simply set dst->cpu_switch to NULL in dsa_dst_unapply()
which guarantees that we always correctly re-assign dst->cpu_switch in
dsa_cpu_parse().

Fixes: 9520ed8f ("net: dsa: use cpu_switch instead of ds[0]")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ip6_find_1stfragopt() fails and we return an error we have to free
up 'segs' because nobody else is going to.

Fixes: 2423496a ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 9b4437a5 ("geneve: Unify LWT and netdev handling.")
when using COLLECT_METADATA geneve devices are created with too small of
a needed_headroom and too large of a max_mtu. This is because
ip_tunnel_info_af() is not valid with the device level info when using
COLLECT_METADATA and we mistakenly fall into the IPv4 case.

For COLLECT_METADATA, always use the worst case of ipv6 since both
sockets are created.

Fixes: 9b4437a5 ("geneve: Unify LWT and netdev handling.")
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to f5f99309 (sock: do not set sk_err in
sock_dequeue_err_skb), sk_err was reset to the error of
the skb on the head of the error queue.

Applications, most notably ping, are relying on this
behavior to reset sk_err for ICMP packets.

Set sk_err to the ICMP error when there is an ICMP packet
at the head of the error queue.

Fixes: f5f99309 (sock: do not set sk_err in sock_dequeue_err_skb)
Reported-by: Cyril Hrubis <chrubis@suse.cz>
Tested-by: Cyril Hrubis <chrubis@suse.cz>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6_route_output() requires that the flowlabel contains the traffic
class for policy routing.

Commit 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets") removed the code which previously added the
traffic class to the flowlabel.

The traffic class is added here because only route lookup needs the
flowlabel to contain the traffic class.

Fixes: 0e9a7095 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature.  Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.

The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is.  The feature eliminates the need for
software to poll the MDIO bus.

Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:

1. It assumes a compatible register set, so PHYs with different registers
   may not work.

2. It doesn't allow for hardware errata that have work-arounds implemented
   in the PHY driver.

3. It doesn't support multiple register pages. If the PHY core switches
   the register set to another page, the EMAC won't know the page has
   changed and will still attempt to read the same PHY register.

4. It only checks the copper side of the link, not the SGMII side.  Some
   PHY drivers (e.g. at803x) may also check the SGMII side, and
   report the link as not ready during autonegotiation if the SGMII link
   is still down.  Phylib then waits for another interrupt to query
   the PHY again, but the EMAC won't send another interrupt because it
   thinks the link is up.

Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit d85b758f ("virtio_net: fix support for small rings")
was supposed to increase the buffer size for small rings but had an
unintentional side effect of decreasing it for large rings. This seems
to break some setups - it's not yet clear why, but increasing buffer
size back to what it was before helps.

Fixes: d85b758f ("virtio_net: fix support for small rings")
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: "J. Bruce Fields" <bfields@fieldses.org>
Tested-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.

This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding a vxlan interface to a socket isn't symmetrical, while adding
is done in vxlan_open() the deletion is done in vxlan_dellink().
This can cause a use-after-free error when we close the vxlan
interface before deleting it.

We add vxlan_vs_del_dev() to match vxlan_vs_add_dev() and call
it from vxlan_stop() to match the call from vxlan_open().

Fixes: 56ef9c90 ("vxlan: Move socket initialization to within rtnl scope")
Acked-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original author left the project and so far has not
responded to emails sent to the listed address.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>