This bus clock is needed for pinctrl register access to work. Add it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240430-samsung-pinctrl-busclock-dts-v2-2-14fc988139dd@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

This bus clock is needed for pinctrl register access to work. Add it.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240430-samsung-pinctrl-busclock-dts-v2-1-14fc988139dd@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Enable ufs & ufs phy nodes for Oriole. Also define the ufs regulator node.

ufs regulator is a stub until full s2mpg11 slave pmic support is added.
The gpio defined is for the BOOTLD0 (gs101) signal connected to
UFS_EN(s2mpg11) gpio enabled voltage rail for UFS.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240430141445.2688499-4-peter.griffin@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Add the ufs controller node and phy node for gs101.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240430141445.2688499-3-peter.griffin@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

This has some configuration bits such as sharability that
are required by UFS.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240430141445.2688499-2-peter.griffin@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Update dt schema to include the gs101 hsi2 sysreg compatible.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240429111537.2369227-2-peter.griffin@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Pixel 6 (Oriole) has a USB-C connector that can act as host or device.

The USB role is detected dynamically using a MAX77759 TCPCI controller,
but since there is no driver for the MAX77759, the role is defaulted to
peripheral, without any endpoints / ports.

This allows Oriole to be configured as a gadget, e.g. using configfs.

As PMIC regulators are not implemented yet, we rely on USB LDOs being
enabled by the bootloader. A placeholder regulator is used for now.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240429-usb-dts-gs101-v2-2-7c1797c9db80@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Add the USB 3.1 Dual Role Device (DRD) controller and USB-PHY nodes for
Google Tensor GS101.

The USB 3.1 DRD controller has the following features:
* compliant with both USB device 3.1 and USB device 2.0 standards
* compliant with USB host 3.1 and USB host 2.0 standards
* supports USB device 3.1 and USB device 2.0 interfaces
* supports USB host 3.1 and USB host 2.0 interfaces
* full-speed (12 Mbps) and high-speed (480 Mbps) modes with USB device
  2.0 interface
* super-speed (5 Gbps) mode with USB device 3.1 Gen1 interface
* super-speed plus (10 Gbps) mode with USB device 3.1 Gen2 interface
* single USB port which can be used for USB 3.1 or USB 2.0
* on-chip USB PHY transceiver
* DWC3 compatible
* supports up to 16 bi-directional endpoints
* compliant with xHCI 1.1 specification
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240429-usb-dts-gs101-v2-1-7c1797c9db80@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Enable the cmu_hsi2 clock management unit. It feeds some of
the high speed interfaces such as PCIe and UFS.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240429-hsi0-gs101-v3-2-f233be0a2455@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Enable the cmu-hsi0 clock controller. It feeds USB.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240426-hsi0-gs101-v2-2-2157da8b63e3@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Add dt schema documentation and clock IDs for the High Speed Interface
2 (HSI2) clock management unit. This CMU feeds high speed interfaces
such as PCIe and UFS.

[AD: * keep CMUs in google,gs101.h sorted alphabetically
     * resolve minor merge conflicts in google,gs101-clock.yaml
     * s/ufs_embd/ufs    s/mmc_card/mmc
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240429-hsi0-gs101-v3-1-f233be0a2455@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Add dt-schema documentation and clock IDs for the high speed interface
0 HSI0 clock management unit. This is used (amongst others) for USB.

While the usual (sed) script has been used to derive the linux clock
IDs from the data sheet, one manual tweak was applied to fix a typo
which we don't want to carry:
    HSI0_USPDPDBG_USER -> HSI0_USBDPDBG_USER (note USB vs USP).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://lore.kernel.org/r/20240423-hsi0-gs101-v1-1-2c3ddb50c720@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Universal Serial Interface (USI) supports three types of serial
interface such as UART, SPI and I2C. Each protocol works independently.
USI can be configured to work as one of these protocols. Define all the
USI nodes from the PERIC blocks (USI0-14), in all their possible
configurations. These blocks have the TX/RX FIFO depth of 64 bytes.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240326151301.348932-6-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

These lines fit 81 characters, which is pretty close to 80.
Join the lines for better readability.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240326151301.348932-5-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Move the pinctrl-* properties after clocks so that we keep alphabetic
order and align with the other similar definitions.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240326151301.348932-4-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

The pinctrl nodes are coming from the shared gs101-pinctrl.dtsi,
thus the pinctrl-0/names shall stay in dtsi. Move them.
Reviewed-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240326151301.348932-3-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

The Preferred order for these is pinctrl-0 pinctrl-names.

Update the DTSI & DTS accordingly.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240326151301.348932-2-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Define CPU cluster 0 and CPU cluster 1 CMUs, which generate CPU clocks,
and add corresponding CPU clocks to CPU nodes.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20240301015118.30072-3-semen.protsenko@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Up to now the SPI alias was used as an index into an array defined in
the SPI driver to determine the SPI FIFO depth. Drop the dependency on
the SPI alias and specify the SPI FIFO depth directly into the SPI node.

There are no SPI aliases defined, thus the FIFO depth was determined by
matching the FIFO depth of the I2C node of the same USI parent.
No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240216140449.2564625-7-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Up to now the SPI alias was used as an index into an array defined in
the SPI driver to determine the SPI FIFO depthj Drop the dependency on
the SPI alias and specify the SPI FIFO depth directly into the SPI node.

The FIFO depth were determined based on the SPI aliases that are defined
in exynos5433-tm2-common.dtsi:
	spi0 = &spi_0;
	spi1 = &spi_1;
	spi2 = &spi_2;
	spi3 = &spi_3;
	spi4 = &spi_4;
spi-s3c64xx.c driver defines the following fifo_lvl_mask for the
"samsung,exynos5433-spi" compatible:
	.fifo_lvl_mask  = { 0x1ff, 0x7f, 0x7f, 0x7f, 0x7f, 0x1ff},
Thus spi{0, 4} were considered having 256 byte FIFO depths, and
spi{1, 2, 3} having 64 byte FIFO depths. Update device tree with these
FIFO depths. No functional change expected.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240216140449.2564625-6-tudor.ambarus@linaro.orgSigned-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Pull EFI fixes from Ard Biesheuvel:

 - Fix logic that is supposed to prevent placement of the kernel image
   below LOAD_PHYSICAL_ADDR

 - Use the firmware stack in the EFI stub when running in mixed mode

 - Clear BSS only once when using mixed mode

 - Check efi.get_variable() function pointer for NULL before trying to
   call it

* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: fix panic in kdump kernel
  x86/efistub: Don't clear BSS twice in mixed mode
  x86/efistub: Call mixed mode boot services on the firmware's stack
  efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address

Pull x86 fixes from Thomas Gleixner:

 - Ensure that the encryption mask at boot is properly propagated on
   5-level page tables, otherwise the PGD entry is incorrectly set to
   non-encrypted, which causes system crashes during boot.

 - Undo the deferred 5-level page table setup as it cannot work with
   memory encryption enabled.

 - Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
   to the default value but the cached variable is not, so subsequent
   comparisons might yield the wrong result and as a consequence the
   result prevents updating the MSR.

 - Register the local APIC address only once in the MPPARSE enumeration
   to prevent triggering the related WARN_ONs() in the APIC and topology
   code.

 - Handle the case where no APIC is found gracefully by registering a
   fake APIC in the topology code. That makes all related topology
   functions work correctly and does not affect the actual APIC driver
   code at all.

 - Don't evaluate logical IDs during early boot as the local APIC IDs
   are not yet enumerated and the invoked function returns an error
   code. Nothing requires the logical IDs before the final CPUID
   enumeration takes place, which happens after the enumeration.

 - Cure the fallout of the per CPU rework on UP which misplaced the
   copying of boot_cpu_data to per CPU data so that the final update to
   boot_cpu_data got lost which caused inconsistent state and boot
   crashes.

 - Use copy_from_kernel_nofault() in the kprobes setup as there is no
   guarantee that the address can be safely accessed.

 - Reorder struct members in struct saved_context to work around another
   kmemleak false positive

 - Remove the buggy code which tries to update the E820 kexec table for
   setup_data as that is never passed to the kexec kernel.

 - Update the resource control documentation to use the proper units.

 - Fix a Kconfig warning observed with tinyconfig

* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Move 5-level paging global variable assignments back
  x86/boot/64: Apply encryption mask to 5-level pagetable update
  x86/cpu: Add model number for another Intel Arrow Lake mobile processor
  x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
  Documentation/x86: Document that resctrl bandwidth control units are MiB
  x86/mpparse: Register APIC address only once
  x86/topology: Handle the !APIC case gracefully
  x86/topology: Don't evaluate logical IDs during early boot
  x86/cpu: Ensure that CPU info updates are propagated on UP
  kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
  x86/pm: Work around false positive kmemleak report in msr_build_context()
  x86/kexec: Do not update E820 kexec table for setup_data
  x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'

Pull scheduler doc clarification from Thomas Gleixner:
 "A single update for the documentation of the base_slice_ns tunable to
  clarify that any value which is less than the tick slice has no effect
  because the scheduler tick is not guaranteed to happen within the set
  time slice"

* tag 'sched-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/doc: Update documentation for base_slice_ns and CONFIG_HZ relation

Pull dma-mapping fixes from Christoph Hellwig:
 "This has a set of swiotlb alignment fixes for sometimes very long
  standing bugs from Will. We've been discussion them for a while and
  they should be solid now"

* tag 'dma-mapping-6.9-2024-03-24' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: Reinstate page-alignment for mappings >= PAGE_SIZE
  iommu/dma: Force swiotlb_max_mapping_size on an untrusted device
  swiotlb: Fix alignment checks when both allocation and DMA masks are present
  swiotlb: Honour dma_alloc_coherent() alignment in swiotlb_alloc()
  swiotlb: Enforce page alignment in swiotlb_alloc()
  swiotlb: Fix double-allocation of slots due to broken alignment handling

Check if get_next_variable() is actually valid pointer before
calling it. In kdump kernel this method is set to NULL that causes
panic during the kexec-ed kernel boot.

Tested with QEMU and OVMF firmware.

Fixes: bad267f9 ("efi: verify that variable services are supported")
Signed-off-by: Oleksandr Tymoshenko <ovt@google.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.

So make the memset() conditional on whether the EFI stub is running in
native mode.

Fixes: b3810c5a ("x86/efistub: Clear decompressor BSS in native EFI entrypoint")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Normally, the EFI stub calls into the EFI boot services using the stack
that was live when the stub was entered. According to the UEFI spec,
this stack needs to be at least 128k in size - this might seem large but
all asynchronous processing and event handling in EFI runs from the same
stack and so quite a lot of space may be used in practice.

In mixed mode, the situation is a bit different: the bootloader calls
the 32-bit EFI stub entry point, which calls the decompressor's 32-bit
entry point, where the boot stack is set up, using a fixed allocation
of 16k. This stack is still in use when the EFI stub is started in
64-bit mode, and so all calls back into the EFI firmware will be using
the decompressor's limited boot stack.

Due to the placement of the boot stack right after the boot heap, any
stack overruns have gone unnoticed. However, commit

  5c4feadb0011983b ("x86/decompressor: Move global symbol references to C code")

moved the definition of the boot heap into C code, and now the boot
stack is placed right at the base of BSS, where any overruns will
corrupt the end of the .data section.

While it would be possible to work around this by increasing the size of
the boot stack, doing so would affect all x86 systems, and mixed mode
systems are a tiny (and shrinking) fraction of the x86 installed base.

So instead, record the firmware stack pointer value when entering from
the 32-bit firmware, and switch to this stack every time a EFI boot
service call is made.

Cc: <stable@kernel.org> # v6.1+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>

Commit 63bed966 ("x86/startup_64: Defer assignment of 5-level paging
global variables") moved assignment of 5-level global variables to later
in the boot in order to avoid having to use RIP relative addressing in
order to set them. However, when running with 5-level paging and SME
active (mem_encrypt=on), the variables are needed as part of the page
table setup needed to encrypt the kernel (using pgd_none(), p4d_offset(),
etc.). Since the variables haven't been set, the page table manipulation
is done as if 4-level paging is active, causing the system to crash on
boot.

While only a subset of the assignments that were moved need to be set
early, move all of the assignments back into check_la57_support() so that
these assignments aren't spread between two locations. Instead of just
reverting the fix, this uses the new RIP_REL_REF() macro when assigning
the variables.

Fixes: 63bed966 ("x86/startup_64: Defer assignment of 5-level paging global variables")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/2ca419f4d0de719926fd82353f6751f717590a86.1711122067.git.thomas.lendacky@amd.com

When running with 5-level page tables, the kernel mapping PGD entry is
updated to point to the P4D table. The assignment uses _PAGE_TABLE_NOENC,
which, when SME is active (mem_encrypt=on), results in a page table
entry without the encryption mask set, causing the system to crash on
boot.

Change the assignment to use _PAGE_TABLE instead of _PAGE_TABLE_NOENC so
that the encryption mask is set for the PGD entry.

Fixes: 533568e0 ("x86/boot/64: Use RIP_REL_REF() to access early_top_pgt[]")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/8f20345cda7dbba2cf748b286e1bc00816fe649a.1711122067.git.thomas.lendacky@amd.com

This one is the regular laptop CPU.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240322161725.195614-1-tony.luck@intel.com

Commit 67236547 ("x86/fpu: Update XFD state where required") and
commit 8bf26758 ("x86/fpu: Add XFD state to fpstate") introduced a
per CPU variable xfd_state to keep the MSR_IA32_XFD value cached, in
order to avoid unnecessary writes to the MSR.

On CPU hotplug MSR_IA32_XFD is reset to the init_fpstate.xfd, which
wipes out any stale state. But the per CPU cached xfd value is not
reset, which brings them out of sync.

As a consequence a subsequent xfd_update_state() might fail to update
the MSR which in turn can result in XRSTOR raising a #NM in kernel
space, which crashes the kernel.

To fix this, introduce xfd_set_state() to write xfd_state together
with MSR_IA32_XFD, and use it in all places that set MSR_IA32_XFD.

Fixes: 67236547 ("x86/fpu: Update XFD state where required")
Signed-off-by: Adamos Ttofari <attofari@amazon.de>
Signed-off-by: Chang S. Bae <chang.seok.bae@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240322230439.456571-1-chang.seok.bae@intel.com

Closes: https://lore.kernel.org/lkml/20230511152818.13839-1-attofari@amazon.de

The memory bandwidth software controller uses 2^20 units rather than
10^6. See mbm_bw_count() which computes bandwidth using the "SZ_1M"
Linux define for 0x00100000.

Update the documentation to use MiB when describing this feature.
It's too late to fix the mount option "mba_MBps" as that is now an
established user interface.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240322182016.196544-1-tony.luck@intel.com

Pull timer fixes from Thomas Gleixner:
 "Two regression fixes for the timer and timer migration code:

   - Prevent endless timer requeuing which is caused by two CPUs racing
     out of idle. This happens when the last CPU goes idle and therefore
     has to ensure to expire the pending global timers and some other
     CPU come out of idle at the same time and the other CPU wins the
     race and expires the global queue. This causes the last CPU to
     chase ghost timers forever and reprogramming it's clockevent device
     endlessly.

     Cure this by re-evaluating the wakeup time unconditionally.

   - The split into local (pinned) and global timers in the timer wheel
     caused a regression for NOHZ full as it broke the idle tracking of
     global timers. On NOHZ full this prevents an self IPI being sent
     which in turn causes the timer to be not programmed and not being
     expired on time.

     Restore the idle tracking for the global timer base so that the
     self IPI condition for NOHZ full is working correctly again"

* tag 'timers-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers: Fix removed self-IPI on global timer's enqueue in nohz_full
  timers/migration: Fix endless timer requeue after idle interrupts

Pull more clocksource updates from Thomas Gleixner:
 "A set of updates for clocksource and clockevent drivers:

   - A fix for the prescaler of the ARM global timer where the prescaler
     mask define only covered 4 bits while it is actully 8 bits wide.
     This obviously restricted the possible range of prescaler
     adjustments

   - A fix for the RISC-V timer which prevents a timer interrupt being
     raised while the timer is initialized

   - A set of device tree updates to support new system on chips in
     various drivers

   - Kernel-doc and other cleanups all over the place"

* tag 'timers-core-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/timer-riscv: Clear timer interrupt on timer initialization
  dt-bindings: timer: Add support for cadence TTC PWM
  clocksource/drivers/arm_global_timer: Simplify prescaler register access
  clocksource/drivers/arm_global_timer: Guard against division by zero
  clocksource/drivers/arm_global_timer: Make gt_target_rate unsigned long
  dt-bindings: timer: add Ralink SoCs system tick counter
  clocksource: arm_global_timer: fix non-kernel-doc comment
  clocksource/drivers/arm_global_timer: Remove stray tab
  clocksource/drivers/arm_global_timer: Fix maximum prescaler value
  clocksource/drivers/imx-sysctr: Add i.MX95 support
  clocksource/drivers/imx-sysctr: Drop use global variables
  dt-bindings: timer: nxp,sysctr-timer: support i.MX95
  dt-bindings: timer: renesas: ostm: Document RZ/Five SoC
  dt-bindings: timer: renesas,tmu: Document input capture interrupt
  clocksource/drivers/ti-32K: Fix misuse of "/**" comment
  clocksource/drivers/stm32: Fix all kernel-doc warnings
  dt-bindings: timer: exynos4210-mct: Add google,gs101-mct compatible
  clocksource/drivers/imx: Fix -Wunused-but-set-variable warning

Pull irq fixes from Thomas Gleixner:
 "A series of fixes for the Renesas RZG21 interrupt chip driver to
  prevent spurious and misrouted interrupts.

   - Ensure that posted writes are flushed in the eoi() callback

   - Ensure that interrupts are masked at the chip level when the
     trigger type is changed

   - Clear the interrupt status register when setting up edge type
     trigger modes

   - Ensure that the trigger type and routing information is set before
     the interrupt is enabled"

* tag 'irq-urgent-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time
  irqchip/renesas-rzg2l: Prevent spurious interrupts when setting trigger type
  irqchip/renesas-rzg2l: Rename rzg2l_irq_eoi()
  irqchip/renesas-rzg2l: Rename rzg2l_tint_eoi()
  irqchip/renesas-rzg2l: Flush posted write in irq_eoi()

Pull core entry fix from Thomas Gleixner:
 "A single fix for the generic entry code:

  The trace_sys_enter() tracepoint can modify the syscall number via
  kprobes or BPF in pt_regs, but that requires that the syscall number
  is re-evaluted from pt_regs after the tracepoint.

  A seccomp fix in that area removed the re-evaluation so the change
  does not take effect as the code just uses the locally cached number.

  Restore the original behaviour by re-evaluating the syscall number
  after the tracepoint"

* tag 'core-entry-2024-03-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  entry: Respect changes to system call number by trace_sys_enter()

Pull more powerpc updates from Michael Ellerman:

 - Handle errors in mark_rodata_ro() and mark_initmem_nx()

 - Make struct crash_mem available without CONFIG_CRASH_DUMP

Thanks to Christophe Leroy and Hari Bathini.

* tag 'powerpc-6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/kdump: Split KEXEC_CORE and CRASH_DUMP dependency
  powerpc/kexec: split CONFIG_KEXEC_FILE and CONFIG_CRASH_DUMP
  kexec/kdump: make struct crash_mem available without CONFIG_CRASH_DUMP
  powerpc: Handle error in mark_rodata_ro() and mark_initmem_nx()

Pull ARM updates from Russell King:

 - remove a misuse of kernel-doc comment

 - use "Call trace:" for backtraces like other architectures

 - implement copy_from_kernel_nofault_allowed() to fix a LKDTM test

 - add a "cut here" line for prefetch aborts

 - remove unnecessary Kconfing entry for FRAME_POINTER

 - remove iwmmxy support for PJ4/PJ4B cores

 - use bitfield helpers in ptrace to improve readabililty

 - check if folio is reserved before flushing

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9359/1: flush: check if the folio is reserved for no-mapping addresses
  ARM: 9354/1: ptrace: Use bitfield helpers
  ARM: 9352/1: iwmmxt: Remove support for PJ4/PJ4B cores
  ARM: 9353/1: remove unneeded entry for CONFIG_FRAME_POINTER
  ARM: 9351/1: fault: Add "cut here" line for prefetch aborts
  ARM: 9350/1: fault: Implement copy_from_kernel_nofault_allowed()
  ARM: 9349/1: unwind: Add missing "Call trace:" line
  ARM: 9334/1: mm: init: remove misuse of kernel-doc comment