Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.

This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.

Cc: stable@vger.kernel.org
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.10-rc cycle. Mostly a DMA regression fix for
omap1, and then a handful of trivial fixes for boards and devices to
work:

- Fixes TI wilink bluetooth strange platform data baud rate
- Remove duplicate pinmux line for am335x-icev2
- Fix omap1 dma regression
- Fix uninitialized return value for wkup_m3_ipc_probe()
- Fix Ethernet PHY binding typo for dra72-evm
- Fix init for omap5 and dra7 sata ports
- Fix mmc card detect pin for Logic PD SOM-LV

* tag 'omap-for-v4.10/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
  ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
  ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
  soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
  ARM: OMAP1: DMA: Correct the number of logical channels
  ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
  ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
Signed-off-by: Olof Johansson <olof@lixom.net>

This fixes commit ab8dd3ae ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV") where the Card Detect and Write Protect
pins were improperly configured.

Fixes: ab8dd3ae ("ARM: DTS: Add minimal Support for
Logic PD DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The current hardware is not able to run with all cores enabled at a
cluster frequency superior at 1536MHz.
But the currently shipped u-boot for the platform still reports an OPP
table with possible DVFS frequency up to 2GHz, and will not change since
the off-tree linux tree supports limiting the OPPs with a kernel parameter.
A recent u-boot change reports the boot-time DVFS around 100MHz and
the default performance cpufreq governor sets the maximum frequency.
Previous version of u-boot reported to be already at the max OPP and
left the OPP as is.
Nevertheless, other governors like ondemand could setup the max frequency
and make the system crash.

This patch disables the DVFS clock and disables cpufreq.

Fixes: 70db166a ("ARM64: dts: meson-gxbb: Add SCPI with cpufreq & sensors Nodes")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'ux500-fix-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes

A single PM fix from Arnd

* tag 'ux500-fix-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request contains Broadcom ARM-based SoC Device Tree fixes for v4.10, please
pull the following:

- Jon fixes an invalid value for the "ranges" property of the bus nodes on NorthStar
  Plus SoCs

* tag 'arm-soc/for-4.10/devicetree-fixes' of http://github.com/Broadcom/stblinux:
  ARM: dts: NSP: Fix DT ranges error
Signed-off-by: Olof Johansson <olof@lixom.net>

This pull request contains fixes to multi_v7_defconfig for Broadcom ARM-based
SoCs, please pull the following changes:

- Valenting fixes two incorrect Kconfig symbols for BCM47xx: NVRAM and watchdog drivers

* tag 'arm-soc/for-4.10/defconfig-fixes' of http://github.com/Broadcom/stblinux:
  ARM: multi_v7_defconfig: set bcm47xx watchdog
  ARM: multi_v7_defconfig: fix config typo
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes

Samsung fixes for v4.10:
1. Update maintainers entry with Patchwork address.
2. Fix invalid values for NF_CT_PROTO_* in s3c2410 defconfig (these options
   cannot be modules anymore).

* tag 'samsung-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: s3c2410_defconfig: Fix invalid values for NF_CT_PROTO_*
  MAINTAINERS: Add Patchwork URL to Samsung Exynos entry
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'sunxi-fixes-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes

Allwinner fixes for 4.10

A few fixes here and there to enable the build of some DT leftover, prevent
display issues or setup a proper muxing.

* tag 'sunxi-fixes-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
  ARM: dts: sun8i: Support DTB build for NanoPi M1
  ARM: dts: sun6i: hummingbird: Enable display engine again
  ARM: dts: sun6i: Disable display pipeline by default
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

i.MX fixes for 4.10, 2nd round:
 - A couple of Nitrogen6 device tree fixes for audio codec probe
   failure, which is caused by that pinctrl setting for codec clock
   was not in the correct device node.

* tag 'imx-fixes-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
  ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
Signed-off-by: Olof Johansson <olof@lixom.net>

AHCI provides the register PORTS_IMPL to let the software know which port
is supported. The register must be initialized by the bootloader. However
in some cases u-boot doesn't properly initialize this value (if it is not
compiled with SATA support for example or if the SATA initialization fails).
The DTS entry "ports-implemented" can be used to override the value in
PORTS_IMPL.

Without this patch the SATA will not work in the following two cases:

* if there has been a failure to initialize SATA in u-boot.

* if ahci_platform module has been removed and re-inserted. The reason is
  that the content of PORTS_IMPL is lost after the module is removed.
  I suspect that it's because the controller is reset by the hwmod.

Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated comments with what goes wrong]
Signed-off-by: Tony Lindgren <tony@atomide.com>

The range size for axi is 0x2 bytes too small, as the QSPI needs
0x11c408 + 0x004 (which is 0x0011c40c, not 0x0011c40a).  No errors have
been observed with this shortcoming, but fixing it for correctness.

Fixes: 329f98c1 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Correct the bcm47xx watchdog option.  The convention of bcm watchdogs is
the _WDT suffix.

Fixes: 8dace304 ("ARM: multi_v7_defconfig: Enable BCM47xx/BCM5301x drivers")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

s/CONFIG_CONFIG_BCM47XX_NVRAM/CONFIG_BCM47XX_NVRAM/

Fixes: 8dace304 ("ARM: multi_v7_defconfig: Enable BCM47xx/BCM5301x drivers")
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Fix a typo in impedance setting for ethernet-phy@3

Fixes: b76db38c ("ARM: dts: dra72-evm-revc: add phy impedance settings")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix to return a negative error code from the kthread_run() error
handling case instead of 0, as done elsewhere in this function.

Fixes: cdd5de50 ("soc: ti: Add wkup_m3_ipc driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This function clearly never worked and always returns true,
as pointed out by gcc-7:

arch/arm/mach-ux500/pm.c: In function 'prcmu_is_cpu_in_wfi':
arch/arm/mach-ux500/pm.c:137:212: error: ?:
using integer constants in boolean context, the expression
will always evaluate to 'true' [-Werror=int-in-bool-context]

With the added braces, the condition actually makes sense.

Fixes: 34fe6f10 ("mfd : Check if the other db8500 core is in WFI")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The node name for the power seq pin is mmc2@0 like the mmc2_pins_a one.
This makes the original node (mmc2_pins_a) scrapped out of the dtb and
result in a unusable eMMC if U-Boot didn't configured the pins to the
correct functions.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The commit 10efbf5f ("ARM: dts: sun8i: Add dts file for NanoPi M1 SBC")
introduced NanoPi M1 board but it's missing in Allwinner H3 DTB build.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we disable the display engine by default, we need to re-enable
it for the Hummingbird A31, which already had its display pipeline
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

While we now support the internal display pipeline found on sun6i, it
is possible that we are unable to enable the display for some boards,
due to a lack of drivers for the panels or bridges found on them. If
the display pipeline is enabled, the driver will try to enable, and
possibly screw up the simple framebuffer U-boot had configured.

Disable the display pipeline by default.

Fixes: 6d0e5b70 ("ARM: dts: sun6i: Add device nodes for first
		      display pipeline")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Tree-wide replacement was done by commit 2ef7d5f3 ("ARM, ARM64:
dts: drop "arm,amba-bus" in favor of "simple-bus"), then the 2nd
round by commit 15b7cc78 ("arm64: dts: drop "arm,amba-bus" in
favor of "simple-bus" part 2").

Here, some new users have appeared for Linux v4.10-rc1.  Eliminate
them now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

arm: Xilinx ZynqMP DT fixes for v4.10

- Fix dtc warnings
- Fix i2c compatible string

* tag 'zynmp-dt-fixes-for-4.10' of https://github.com/Xilinx/linux-xlnx:
  ARM64: zynqmp: Fix i2c node's compatible string
  ARM64: zynqmp: Fix W=1 dtc 1.4 warnings
Signed-off-by: Olof Johansson <olof@lixom.net>

Since the codec is probed first, the pinctrl node should be
under the codec node.

The codec init was working for this board since U-Boot was
already setting GPIO_0 as CLKO1 but better fix it anyway.

Fixes: 3faa1bb2 ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch fixes the following error:
sgtl5000 0-000a: Error reading chip id -6
imx-sgtl5000 sound: ASoC: CODEC DAI sgtl5000 not registered
imx-sgtl5000 sound: snd_soc_register_card failed (-517)

The problem was that the pinctrl group was linked to the sound driver
instead of the codec node. Since the codec is probed first, the sys_mclk
was missing and it would therefore fail to initialize.

Fixes: b32e7002 ("ARM: dts: imx: add Boundary Devices Nitrogen6_Max board")
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.

The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.

The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is no mmc sd card detect on am335x-ice board. But the spi0_cs1
pin being configured as mmcsd_cd. Removing it fixes the below warning
during boot:

pinctrl-single 44e10800.pinmux: pin 44e10960.0 already
requested by 48030000.spi; cannot claim for 48060000.mmc
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: tidied up commit message]
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 485fa126 ("ARM: OMAP2+: LogicPD Torpedo + Wireless: Add Bluetooth")
set the wrong baud rate for the UART. The Baud rate was 300,000 and it should
be 3,000,000 for WL1283.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'davinci-fixes-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes

Pull "DaVinci fixes for v4.10" from Sekhar Nori:

This pull request contains fixes for the following issues

1) Fix two instances of infinite loop occurring in
   clock list for DA850. This fixes kernel hangs in some
   instances and so have been marked for stable kernel.

2) Fix for sleeping function called from atomic context
   with USB 2.0 clock management code introduced in v4.10
   merge window.

* tag 'davinci-fixes-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: davinci: da8xx: Fix sleeping function called from invalid context
  ARM: davinci: Make __clk_{enable,disable} functions public
  ARM: davinci: da850: don't add emac clock to lookup table twice
  ARM: davinci: da850: fix infinite loop in clk_set_rate()

Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Pull "Amlogic fixes for v4.10" from Kevin Hilman:

- DT: GXL: fix GPIO include
- add DT and defconfig for newly merged DRM driver

This pull has one real fix, as a couple non-critical ones.  The DRM
DT/defconfig patches are coming now because I didn't expect the new
driver to make it for the v4.10 merge window, but since it did[1], the
DT and defconfig should go into the same release.

[1] bbbe775e drm: Add support for Amlogic Meson Graphic Controller

* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: defconfig: enable DRM_MESON as module
  ARM64: dts: meson-gx: Add Graphic Controller nodes
  ARM64: dts: meson-gxl: fix GPIO include

Merge tag 'psci-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/linux into fixes

Pull "PSCI fixes for v4.10" from Lorenzo Pieralisi:

Two minor fixes following the merge of the PSCI checker:

- Annotate the PSCI checker timer on the stack used to wake-up from
  suspend to prevent warnings when the DEBUG_OBJECTS config option
  is enabled
- Extend the PSCI entry in the maintainers list to also include the
  PSCI checker code

* tag 'psci-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lpieralisi/linux:
  MAINTAINERS: extend PSCI entry to cover the newly add PSCI checker code
  drivers: psci: annotate timer on stack to silence odebug messages

Merge tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes

Pull "ARMv8 Juno/VExpress fixes for v4.10" from Sudeep Holla:

A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on AEMv8 FVP/RTSM models in order to support split priority drop and
interrupt deactivation.

* tag 'juno-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: vexpress: Support GICC_DIR operations

Merge tag 'vexpress-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes

Pull "ARMv7 VExpress fixes for v4.10" from Sudeep Holla:

A simple fix to extend GICv2 CPU interface registers from 4K to 8K
on VExpress TC1 and TC2 platforms in order to support split priority
drop and interrupt deactivation.

* tag 'vexpress-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  ARM: dts: vexpress: Support GICC_DIR operations

Merge tag 'scpi-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into fixes

Pull "SCPI fix for v4.10" from Sudeep Holla:

A simple fix for reading only lower 32-bit sensor values on pre-1.0 SCPI
firmwares so that upper 32-bit (garbage) value is discarded properly.

* tag 'scpi-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  firmware: arm_scpi: fix reading sensor values on pre-1.0 SCPI firmwares

Merge tag 'imx-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Pull "i.MX fixes for 4.10" from Shawn Guo:

 - A format fix for vf610-zii-dev-rev-b.dts, which has a very odd line
   due to misses a newline.
 - A fix to imx-weim bus error seen on board which doesn't actually use
   the bus.
 - A fix for imx6qdl-nitrogen6x board which has conflicting usage of
   pad NANDF_CS2.
 - A cleanup on i.MX1 machine to remove .map_io callback, which also
   fixes a compiling error for NOMMU build.
 - Fix AVIC base address in i.MX31 device tree source.  The problem was
   shadowed by the AVIC driver, which takes the correct base address
   from a SoC specific header file.

* tag 'imx-fixes-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx6: Disable "weim" node in the dtsi files
  ARM: i.MX: remove map_io callback
  ARM: dts: vf610-zii-dev-rev-b: Add missing newline
  ARM: dts: imx6qdl-nitrogen6x: remove duplicate iomux entry
  ARM: dts: imx31: fix AVIC base address

Merge tag 'qcom-arm-fixes-for-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes

Pull "Qualcomm ARM DTS Fixes for v4.10-rc2" from Andy Gross:

* Add SCM clock for APQ8064 to fix boot failures

* tag 'qcom-arm-fixes-for-4.10-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: qcom: apq8064: Add missing scm clock

Merge tag 'omap-for-v4.10/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Pull "omap fixes for v4.10-rc cycle" from Tony Lindgren:

Fist set of fixes for omaps for v4.10-rc cycle, mostly
to deal with various regressions noticed during the merge
window and to fix various device tree configurations for
boards. Also included is removal of mach-omap2/gpio.c that
is now dead code with device tree based booting that should
be OK for the early -rc cycle:

- A series of fixes to add empty chosen node to fix regressions
  caused for bootloaders that don't create chosen node as the
  decompressor needs the chosen node to merge command line and
  ATAGs into it

- Fix missing logicpd-som-lv-37xx-devkit.dtb entry in Makefile

- Fix regression for am437x timers

- Fix wrong strcat for non-NULL terminated string

- A series of changes to fix tps65217 interrupts to not use
  defines as we don't do that for interrupts

- Two patches to fix USB VBUS detection on am57xx-idk and force it
  to peripheral mode until dwc3 role detection is working

- Add missing dra72-evm-tps65917 missing voltage supplies
  accidentally left out of an earlier patch

- Fix n900 eMMC detection when booted on qemu

- Remove unwanted pr_err on failed memory allocation for
  prm_common.c

- Remove legacy mach-omap2/gpio.c that now is dead code
  since we boot mach-omap2 in device tree only mode

- Fix am572x-idk pcie1 by adding the missing gpio reset pin

* tag 'omap-for-v4.10/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
  ARM: dts: am572x-idk: Add gpios property to control PCIE_RESETn
  ARM: OMAP2+: PRM: Delete an error message for a failed memory allocation
  ARM: dts: n900: Mark eMMC slot with no-sdio and no-sd flags
  ARM: dts: dra72-evm-tps65917: Add voltage supplies to usb_phy, mmc, dss
  ARM: dts: am57xx-idk: Put USB2 port in peripheral mode
  ARM: dts: am57xx-idk: Support VBUS detection on USB2 port
  dt-bindings: input: Specify the interrupt number of TPS65217 power button
  dt-bindings: power/supply: Update TPS65217 properties
  dt-bindings: mfd: Remove TPS65217 interrupts
  ARM: dts: am335x: Fix the interrupt name of TPS65217
  ARM: omap2+: fixing wrong strcat for Non-NULL terminated string
  ARM: omap2+: am437x: rollback to use omap3_gptimer_timer_init()
  ARM: dts: omap3: Add DTS for Logic PD SOM-LV 37xx Dev Kit
  ARM: dts: dra7: Add an empty chosen node to top level DTSI
  ARM: dts: dm816x: Add an empty chosen node to top level DTSI
  ARM: dts: dm814x: Add an empty chosen node to top level DTSI
  ARM: dts: am4372: Add an empty chosen node to top level DTSI
  ARM: dts: am33xx: Add an empty chosen node to top level DTSI
  ARM: dts: omap5: Add an empty chosen node to top level DTSI
  ARM: dts: omap4: Add an empty chosen node to top level DTSI
  ...

Merge tag 'samsung-soc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes

Samsung mach/soc update for v4.10:

1. Minor cleanup in smp_operations.
2. Another step in switching s3c24xx to new DMA API.
3. Drop fixed requirement for HZ=200 on Samsung platforms.

* tag 'samsung-soc-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: Drop fixed 200 Hz timer requirement from Samsung platforms
  ARM: S3C24XX: Add DMA slave maps for remaining s3c24xx SoCs
  ARM: EXYNOS: Remove smp_init_cpus hook from platsmp.c

Merge tag 'qcom-fixes-for-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes

Qualcomm ARM64 Fixes for v4.10-rc1

* Fix instability in MSM8996 due to incorrect carveouts

* tag 'qcom-fixes-for-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: msm8996: Add required memory carveouts

Merge tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Renesas ARM Based SoC Fixes for v4.10

* Provide sd0_uhs node

* tag 'renesas-fixes-for-v4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  arm64: dts: h3ulcb: Provide sd0_uhs node