This sorts out merge conflicts with the arm/gpio branch that
already got merged into mainline Linux.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Fix below build warning and properly set bt_reset pin.

  CC      arch/arm/mach-pxa/cm-x300.o
arch/arm/mach-pxa/cm-x300.c: In function 'cm_x300_init_wi2wi':
arch/arm/mach-pxa/cm-x300.c:779: warning: unused variable 'wlan_en'
arch/arm/mach-pxa/cm-x300.c:795: warning: 'bt_reset' may be used uninitialized in this function
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

GuruPlugD was initially named to be SHEEVAD, and it's causing naming
confusion in the mach-types database. Make it consistent by renaming
to GPLUGD.
Reported-and-Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

Noticed when setting SSP0 in clk_set_rate, _CLK_SET_RATE attempts to
reset the clock divider for the SSP0 parent clock, in this case
IO0FRAC. Bits 24-29 of HW_CLKCTRL_FRAC0 are cleared correctly, but
when the new frac value is written the value isn't shifted up to write
the correct bit-field.  This results in IO0FRAC being set to 0 and
CPUFRAC being corrupted.

This should occur when writing IO1FRAC, EMIFRAC in HW_CLKCTRL_FRAC0
and GPMIFRAC, HSADCFRAC in HW_CLKCTRL_FRAC1.

Tested on custom i.MX28 board with SSP0 SPI driver.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

To configure pads during the initialisation a set of special constants
is used, e.g.
#define MX25_PAD_FEC_MDIO__FEC_MDIO IOMUX_PAD(0x3c4, 0x1cc, 0x10, 0, 0, PAD_CTL_HYS | PAD_CTL_PUS_22K_UP)

The problem is that no pull-up/down is getting activated unless both
PAD_CTL_PUE (pull-up enable) and PAD_CTL_PKE (pull/keeper module
enable) set. This is clearly stated in the i.MX25 datasheet and is
confirmed by the measurements on hardware. This leads to some rather
hard to understand bugs such as misdetecting an absent ethernet PHY (a
real bug i had), unstable data transfer etc. This might affect mx25,
mx35, mx50, mx51 and mx53 SoCs.

It's reasonable to expect that if the pullup value is specified, the
intention was to have it actually active, so we implicitly add the
needed bits.

Cc: stable@kernel.org
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>

While suspending, we're enabling a clock in ->suspend() but we're in atomic
context, leading to this :

[30803.667305] PM: late suspend of devices complete after 1.237 msecs
[30803.667449] BUG: sleeping function called from invalid context at kernel/mutex.c:271
[30803.667464] in_atomic(): 0, irqs_disabled(): 128, pid: 4941, name: pm-suspend
[30803.667474] INFO: lockdep is turned off.
[30803.667483] irq event stamp: 0
[30803.667489] hardirqs last  enabled at (0): [<  (null)>]   (null)
[30803.667503] hardirqs last disabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667543] softirqs last  enabled at (0): [<c001e4a8>] copy_process.part.48+0x1e0/0xa7c
[30803.667562] softirqs last disabled at (0): [<  (null)>]   (null)
[30803.667574] Backtrace:
[30803.667611] [<c0010e00>] (dump_backtrace+0x0/0x110) from [<c0424c00>] (dump_stack+0x18/0x1c)
[30803.667624]  r6:00000000 r5:00000000 r4:d9648000 r3:d9648000
[30803.667652] [<c0424be8>] (dump_stack+0x0/0x1c) from [<c0424eec>] (__might_sleep.part.101+0x90/0xa8)
[30803.667673] [<c0424e5c>] (__might_sleep.part.101+0x0/0xa8) from [<c001a5c4>] (__might_sleep+0x80/0x94)
[30803.667686]  r4:c05d58c0
[30803.667705] [<c001a544>] (__might_sleep+0x0/0x94) from [<c043230c>] (mutex_lock_nested+0x2c/0x30c)
[30803.667735] [<c04322e0>] (mutex_lock_nested+0x0/0x30c) from [<c0017834>] (clk_enable+0x28/0x50)
[30803.667747]  r8:c0438464 r7:00000003 r6:00000000 r5:00000000 r4:c05d2e98
[30803.667780] [<c001780c>] (clk_enable+0x0/0x50) from [<c0017260>] (mx5_suspend_enter+0x1c/0x98)
[30803.667792]  r4:00000003 r3:c060dfe0
[30803.667821] [<c0017244>] (mx5_suspend_enter+0x0/0x98) from [<c0059b48>] (suspend_enter+0xec/0x15c)
[30803.667833]  r4:00000003 r3:c0017244
[30803.667856] [<c0059a5c>] (suspend_enter+0x0/0x15c) from [<c0059c4c>] (suspend_devices_and_enter+0x94/0x130)
[30803.667868]  r6:00000000 r5:00000003 r4:c0c0af00 r3:00002710
[30803.667897] [<c0059bb8>] (suspend_devices_and_enter+0x0/0x130) from [<c0059db0>] (enter_state+0xc8/0x130)
[30803.667909]  r6:00000000 r5:00000003 r4:c05286e4
[30803.667934] [<c0059ce8>] (enter_state+0x0/0x130) from [<c00592d4>] (state_store+0xac/0xc0)
[30803.667945]  r6:00000003 r5:00000003 r4:df39d000 r3:00000003
[30803.667978] [<c0059228>] (state_store+0x0/0xc0) from [<c01b0100>] (kobj_attr_store+0x1c/0x28)
[30803.668009] [<c01b00e4>] (kobj_attr_store+0x0/0x28) from [<c00e435c>] (sysfs_write_file+0x88/0xbc)
[30803.668032] [<c00e42d4>] (sysfs_write_file+0x0/0xbc) from [<c0091fa0>] (vfs_write+0xbc/0x138)
[30803.668051] [<c0091ee4>] (vfs_write+0x0/0x138) from [<c0092204>] (sys_write+0x44/0x70)
[30803.668062]  r8:00000000 r7:00000004 r6:00000003 r5:002694d0 r4:d966acc0
[30803.668094] [<c00921c0>] (sys_write+0x0/0x70) from [<c000db00>] (ret_fast_syscall+0x0/0x3c)
[30803.668106]  r9:d9648000 r8:c000dcc4 r6:00000001 r5:002694d0 r4:00000003
[30803.669927] PM: early resume of devices complete after 0.972 msecs

Just move the clk_enable/disable in ->prepare() and ->finish()
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

This tries to clear up the confusion between integers and iomem pointers
in the marvell pxa platform. MMIO addresses are supposed to be __iomem*
values, in order to let the Linux type checking work correctly. This
patch moves the cast to __iomem as far back as possible, to the place
where the MMIO virtual address windows are defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The sharpsl code selects the max1111 spi driver, so it must also
ensure that SPI itself is enabled. The platform does not work
without max1111.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The two platforms are part of the palm27x family and use the same
code. Select the palm27x symbol to make sure they can be built
standalone.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The raumfeld platform code calls power_supply_set_battery_charged
which is part of the power supply layer, so that always has
to be enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

We cannot support ARMv5 and ARMv7 based boards in a single kernel,
so introduce a new option in mach-pxa to select between the two.

The PJ4 (ARMv7) based boards are now only visible when
CONFIG_ARCH_PXA_V7 is set, the other boards are only visible
when it's not set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The pxa specific cpufreq code is based on the cpu_freq_table
module, so we have to select that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

saarb uses pxa3xx_map_io and pxa3xx_handle_irq, which are part
of the pxa3xx code. This makes sure the necessary header and
implementation is used when building the board file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

There are two variants of the palmtreo machine, the 680 and the
centro, and Kconfig allows selecting one or both of them.
This changes the board file so that it's actually possible
to build all configurations that are allowed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The pxa3xx_u2d_start_hc/pxa3xx_u2d_stop_hc symbols are used by the
ohci-pxa27x driver, which can be a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

When support for zylonite is disabled, the zylonite_pxa300_init
and zylonite_pxa320_init functions are not there, but the declaration
is still kept around if any other boards for the same soc are
enabled. This changes the declaration to be conditional on the
same symbol as the code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Cc: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Defconfig file for at91sam9g45 SoC family:
at91sam9g45, at91sam9g46, at91sam9m10, at91sam9m11.
The Atmel Evaluation Kit for this family is the at91sam9m10g45ek.

It is so useful for automatic compile tests...
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Remove dependency line which was not including the SAM9G45.

[arnd: added dependency on HAVE_CLK to avoid breaking other machines]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This applies ARM errata fix 754322 for all ux500 platforms.

Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

* git://github.com/davem330/net:
  pch_gbe: Fixed the issue on which a network freezes
  pch_gbe: Fixed the issue on which PC was frozen when link was downed.
  make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
  net: xen-netback: correctly restart Tx after a VM restore/migrate
  bonding: properly stop queuing work when requested
  can bcm: fix incomplete tx_setup fix
  RDSRDMA: Fix cleanup of rds_iw_mr_pool
  net: Documentation: Fix type of variables
  ibmveth: Fix oops on request_irq failure
  ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
  cxgb4: Fix EEH on IBM P7IOC
  can bcm: fix tx_setup off-by-one errors
  MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
  dp83640: reduce driver noise
  ptp: fix L2 event message recognition

* 'fix/asoc' of git://github.com/tiwai/sound:
  ASoC: omap_mcpdm_remove cannot be __devexit
  ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
  ASoC: use a valid device for dev_err() in Zylonite

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix channel_remap setup (v2)
  drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
  drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
  drm/radeon: Simplify cursor x/yorigin calculation.
  drm/radeon/kms: fix cursor image off-by-one error
  drm/radeon/kms: Fix logic error in DP HPD handler
  drm/radeon/kms: add retry limits for native DP aux defer
  drm/radeon/kms: fix regression in DP aux defer handling

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi-topcliff-pch: Fix overrun issue
  spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs
  spi-topcliff-pch: Fix CPU read complete condition issue
  spi-topcliff-pch: Fix SSN Control issue
  spi-topcliff-pch: add tx-memory clear after complete transmitting

Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Most asics just use the hw default value which requires
no explicit programming.  For those that need a different
value, the vbios will program it properly.  As such,
there's no need to program these registers explicitly
in the driver.  Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=40103

v2: drop now unused channel_remap functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.

This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.

                      Current                   this patch
Rx-descriptor   4Byte+12Byte*341    -->    12Byte*340-4Byte-12Byte
Rx-threshold                   (Not modified)
Tx-descriptor   4Byte+12Byte*341    -->    16Byte-12Byte*340
Rx-threshold    12Byte              -->    2Byte
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

We found Rx data sometimes drops.(with non-DMA transfer mode)
The cause is read complete condition is not true.

This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

During processing 1 command/data series,
SSN should keep LOW.
However, currently, SSN becomes HIGH.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>