T:  Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3018 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org

The BCM2E96 ID is used by the ECS EF20 laptop, and BCM2E95 is present
in the Weibu F3C. Both are now logged as:

     hci0: BCM: chip id 82
     hci0: BCM43341B0 (002.001.014) build 0000
     hci0: BCM (002.001.014) build 0158

The ECS vendor kernel predates the host-wakeup support in hci_bcm but
it explicitly has a comment saying that the GPIO assignment needs to be
reordered for BCM2E96:
 1. (not used in vendor driver)
 2. Device wakeup
 3. Shutdown

For both devices in question, the DSDT has these GPIOs listed in order
of GpioInt, GpioIo, GpioIo. And if we use the first one listed (GpioInt)
as the host wakeup, that interrupt handler fires while doing bluetooth
I/O.

I am assuming the convention of GPIO ordering has been changed for these
new device IDs, so lets use the new ordering on such devices.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some btbcm devices require more time to complete its reset process.
They won't reply any hci command until reset is done.

[ 17.218554] Bluetooth: hci0 command 0x1001 tx timeout
[ 25.214999] Bluetooth: hci0: BCM: Reading local version info failed (-110)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This is a Boardcom module and requires patchram to work.

T: Bus=01 Lev=03 Prnt=03 Port=01 Cnt=02 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=413c ProdID=8143 Rev= 1.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=20689D1FAF94
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use irqflags parsed from dt.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The irq_of_parse_and_map will return 0 as a invalid irq.

Set irq_bt to -1 in this case, so that the btmrvl resume/suspend code
would not try to enable/disable it.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It's much the same as what we did for mwifiex in:
b9da4d22 mwifiex: avoid double-disable_irq() race

"We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.

Let's disable the IRQ and enable it in case if we have double-disabled
it."
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

As per the comment in include/linux/net.h, the recvfrom handlers
should expect msg_name to be NULL. However, bt_sock_recvmsg()
is currently not checking it, which could lead to a NULL pointer
dereference.

The following NULL pointer dereference was produced while testing
L2CAP datagram reception. Note that the kernel is tainted due to
the r8723bs module being inserted. However, it seems the fix still
applies.

$ l2test -r -G
l2test[326]: Receiving ...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ee008000
[00000000] *pgd=7f896835
Internal error: Oops: 817 [#1] PREEMPT SMP ARM
Modules linked in: r8723bs(O)
CPU: 0 PID: 326 Comm: l2test Tainted: G           O 4.8.0 #1
Hardware name: Allwinner sun7i (A20) Family
task: ef1c6880 task.stack: eea70000
PC is at __memzero+0x58/0x80
LR is at l2cap_skb_msg_name+0x1c/0x4c
pc : [<c02c47d8>]    lr : [<c0506278>]    psr: 00070013
sp : eea71e60  ip : 00000000  fp : 00034e1c
r10: 00000000  r9 : 00000000  r8 : eea71ed4
r7 : 000002a0  r6 : eea71ed8  r5 : 00000000  r4 : ee4a5d80
r3 : 00000000  r2 : 00000000  r1 : 0000000e  r0 : 00000000
Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM Segment none
Control: 10c5387d  Table: 7600806a  DAC: 00000051
Process l2test (pid: 326, stack limit = 0xeea70210)
Stack: (0xeea71e60 to 0xeea72000)
1e60: ee4a5d80 eeac2800 000002a0 c04d7114 173eefa0 00000000 c06ca68e 00000000
1e80: 00000001 eeac2800 eef23500 00000000 000002a0 eea71ed4 eea70000 c0504d50
1ea0: 00000000 00000000 eef23500 00000000 00000000 c044e8a0 eea71edc eea9f904
1ec0: bef89aa0 fffffff7 00000000 00035008 000002a0 00000000 00000000 00000000
1ee0: 00000000 00000000 eea71ed4 00000000 00000000 00000000 00004000 00000000
1f00: 0000011b c01078c4 eea70000 c044e5e4 00000000 00000000 642f0001 6c2f7665
1f20: 0000676f 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1f40: 00000000 00000000 00000000 00000000 00000000 ffffffff 00000001 bef89ad8
1f60: 000000a8 c01078c4 eea70000 00000000 00034e1c c01e6c74 00000000 00000000
1f80: 00034e1c 000341f8 00000000 00000123 c01078c4 c044e90c 00000000 00000000
1fa0: 000002a0 c0107700 00034e1c 000341f8 00000003 00035008 000002a0 00000000
1fc0: 00034e1c 000341f8 00000000 00000123 00000000 00000000 00011ffc 00034e1c
1fe0: 00000000 bef89aa4 0001211c b6eebb60 60070010 00000003 00000000 00000000
[<c02c47d8>] (__memzero) from [<c0506278>] (l2cap_skb_msg_name+0x1c/0x4c)
[<c0506278>] (l2cap_skb_msg_name) from [<c04d7114>] (bt_sock_recvmsg+0x128/0x160)
[<c04d7114>] (bt_sock_recvmsg) from [<c0504d50>] (l2cap_sock_recvmsg+0x98/0x134)
[<c0504d50>] (l2cap_sock_recvmsg) from [<c044e8a0>] (SyS_recvfrom+0x94/0xec)
[<c044e8a0>] (SyS_recvfrom) from [<c044e90c>] (SyS_recv+0x14/0x1c)
[<c044e90c>] (SyS_recv) from [<c0107700>] (ret_fast_syscall+0x0/0x3c)
Code: e3110010 18a0500c e49de004 e3110008 (18a0000c)
---[ end trace 224e35e79fe06b42 ]---
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Marvell devices may have many gpio pins, and hence for wakeup
on these out-of-band pins, the chip needs to be told which pin is
to be used for wakeup, using an hci command.

Thus, we read the pin number etc from the device tree node and send
a command to the chip.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Some onboard BT chips (e.g. Marvell 8997) contain a wakeup pin that
can be connected to a gpio on the CPU side, and can be used to wakeup
the host out-of-band. This can be useful in situations where the
in-band wakeup is not possible or not preferable (e.g. the in-band
wakeup may require the USB host controller to remain active, and
hence consuming more system power during system sleep).

The oob gpio interrupt to be used for wakeup on the CPU side, is
read from the device tree node, (using standard interrupt descriptors).
A devcie tree binding document is also added for the driver. The
compatible string is in compliance with
Documentation/devicetree/bindings/usb/usb-device.txt
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Use a label to remove the repetetive cleanup, for error cases.
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/bluetooth/btqcomsmd.ko | grep alias
$

After this patch:

$ modinfo drivers/bluetooth/btqcomsmd.ko | grep alias
alias:          of:N*T*Cqcom,wcnss-btC*
alias:          of:N*T*Cqcom,wcnss-bt
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

It's a custom USB ID for the broadcom bt adapter in the HTC Vive.

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bb4 ProdID=0306 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM2045A0
S:  SerialNumber=AC3743E110CE
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=btusb
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

dmesg:
Bluetooth: hci0: BCM: chip id 102
Bluetooth: hci0: c-l
Bluetooth: hci0: BCM (001.001.005) build 0000
Bluetooth: hci0: BCM (001.001.005) build 0481
Bluetooth: hci0: BCM20703A1 Generic USB 20Mhz fcbga_BU
Signed-off-by: Christoph Haag <haagch@frickel.club>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Stop accessing timer struct members directly and use setup_timer and
mod_timer helpers intended for that use. It makes the code cleaner and
will allow for easier change of the timer struct internals.
Signed-off-by: Jan Koniarik <jan.koniarik@trustica.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Chas Williams <3chas3@gmail.com>
Cc: <linux-atm-general@lists.sourceforge.net>
Cc: <netdev@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current behaviour of "mirred redirect" action (forward) offload is a bit
odd. For matched packets the action forwards them to the desired
destination, but it also lets the packet duplicates to go the original
way down (bridge, router, etc). That is more like "mirred mirror".
Fix this by using PBS type which behaves exactly like "mirred redirect".
Note that PBS does not support loopback mode.

Fixes: 4cda7d8d ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Corentin Labbe says:

====================
stmmac: misc patchs

This is a follow up of my previous stmmac serie which address some comment
done in v2.
====================
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is easier to follow the logic by removing the not operator
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As suggested by Joe Perches, replacing the "if phydev" logic permit to
reduce indentation in the for loop.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 10/100 case have too many ifcase.
This patch split it for removing an if.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch mutualise a bit by running stmmac_hw_fix_mac_speed() after
the switch in case of valid speed.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of invalid speed given, stmmac_adjust_link() still record it as
current speed.
This patch modify the default case to set speed as SPEED_UNKNOWN if not
10/100/1000.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is better to use DUPLEX_UNKNOWN instead of just "-1".
Using 0 for an invalid speed is bad since 0 is a valid value for speed.
So this patch replace 0 by SPEED_UNKNOWN.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stmmac_adjust_link() function is called too rarely for having
likely() macros being useful.
Just remove likely annotation in it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch remove some useless parenthesis.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pci_enable_msix has been long deprecated, but this driver adds a new
instance.  Convert it to pci_alloc_irq_vectors so that no new instance
of the deprecated function reaches mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed*: Add support for PTP

This patch series adds required changes for qed/qede drivers for
supporting the IEEE Precision Time Protocol (PTP).

Changes from previous versions:
v7: Fixed Kbuild robot warnings.

v6: Corrected broken loop iteration in previous version.
    Reduced approximation error of adjfreq.

v5: Removed two divisions from the adjust-frequency loop.
    Resulting logic would use 8 divisions [instead of 24].

v4: Remove the loop iteration for value '0' in the qed_ptp_hw_adjfreq()
    implementation.

v3: Use div_s64 for 64-bit divisions as do_div gives error for signed
    types.
    Incorporated review comments from Richard Cochran.
      - Clear timestamp resgisters as soon as timestamp is read.
      - Use shift operation in the place of 'divide by 16'.

v2: Use do_div for 64-bit divisions.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the driver support for,
  - Registering the ptp clock functionality with the OS.
  - Timestamping the Rx/Tx PTP packets.
  - Ethtool callbacks related to PTP.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Count buffer group drops or truncates as rx drops rather than
rx errors in netdev stats.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 91572088 ("net: use core MTU range checking in core net
infra") changed the openvswitch internal device to use the core net
infra for controlling the MTU range, but failed to actually set the
max_mtu as described in the commit message, which now defaults to
ETH_DATA_LEN.

This patch fixes this by setting max_mtu to ETH_MAX_MTU after
ether_setup() call.

Fixes: 91572088 ("net: use core MTU range checking in core net infra")
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes broken build for !NET_CLS:

net/built-in.o: In function `fq_codel_destroy':
/home/sab/linux/net-next/net/sched/sch_fq_codel.c:468: undefined reference to `tcf_destroy_chain'

Fixes: cf1facda ("sched: move tcf_proto_destroy and tcf_destroy_chain helpers into cls_api")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is needed to force a rebuild of bpf.o when one of its dependencies
(e.g. uapi/linux/bpf.h) is updated.

Add a phony target.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove a useless ifdef __NR_bpf as requested by Wang Nan.

Inline one-line static functions as it was in the bpf_sys.h file.
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Wang Nan <wangnan0@huawei.com>
Link: https://lkml.kernel.org/r/828ab1ff-4dcf-53ff-c97b-074adb895006@huawei.comAcked-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using a reader-writer lock in fast path is silly, when we can
instead use RCU or a seqlock.

For mlx4 hwstamp clock, a seqlock is the way to go, removing
two atomic operations and false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pch_gbe_get_stats() just returns dev->stats so we can leave it out
altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

hip04_get_stats() just returns dev->stats so we can leave it
out altogether and let dev_get_stats() do the job.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

net/sched/act_api.c:532:5: warning:
 symbol 'nla_memdup_cookie' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove useless ioport.h include.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove the unused timer.  I suppose it was intended as a timeout
detector, but never properly implemented.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>