- 22 Apr, 2017 40 commits
-
-
Max Lohrmann authored
commit 13603685 upstream. As reported by Max, the Windows 2008 R2 chkdsk utility expects VERIFY_16 to be supported, and does not handle the returned CHECK_CONDITION properly, resulting in an infinite loop. The kernel will log huge amounts of this error: kernel: TARGET_CORE[iSCSI]: Unsupported SCSI Opcode 0x8f, sending CHECK_CONDITION. Signed-off-by:
Max Lohrmann <post@wickenrode.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Shaohua Li authored
commit 61eb2b43 upstream. Neil Brown pointed out a potential deadlock in raid 10 code with bio_split/chain. The raid1 code could have the same issue, but recent barrier rework makes it less likely to happen. The deadlock happens in below sequence: 1. generic_make_request(bio), this will set current->bio_list 2. raid10_make_request will split bio to bio1 and bio2 3. __make_request(bio1), wait_barrer, add underlayer disk bio to current->bio_list 4. __make_request(bio2), wait_barrer If raise_barrier happens between 3 & 4, since wait_barrier runs at 3, raise_barrier waits for IO completion from 3. And since raise_barrier sets barrier, 4 waits for raise_barrier. But IO from 3 can't be dispatched because raid10_make_request() doesn't finished yet. The solution is to adjust the IO ordering. Quotes from Neil: " It is much safer to: if (need to split) { split = bio_split(bio, ...) bio_chain(...) make_request_fn(split); generic_make_request(bio); } else make_request_fn(mddev, bio); This way we first process the initial section of the bio (in 'split') which will queue some requests to the underlying devices. These requests will be queued in generic_make_request. Then we queue the remainder of the bio, which will be added to the end of the generic_make_request queue. Then we return. generic_make_request() will pop the lower-level device requests off the queue and handle them first. Then it will process the remainder of the original bio once the first section has been fully processed. " Note, this only happens in read path. In write path, the bio is flushed to underlaying disks either by blk flush (from schedule) or offladed to raid1/10d. It's queued in current->bio_list. Cc: Coly Li <colyli@suse.de> Suggested-by:
NeilBrown <neilb@suse.com> Reviewed-by:
Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Peter Zijlstra authored
commit e7cc4865 upstream. While hunting for clues to a use-after-free, Oleg spotted that perf_event_init_context() can loose an error value with the result that fork() can succeed even though we did not fully inherit the perf event context. Spotted-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: oleg@redhat.com Fixes: 889ff015 ("perf/core: Split context's event group list into pinned and non-pinned lists") Link: http://lkml.kernel.org/r/20170316125823.190342547@infradead.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Marc Zyngier authored
commit 72f31048 upstream. We don't hold the mmap_sem while searching for VMAs (via find_vma), in kvm_arch_prepare_memory_region, which can end up in expected failures. Fixes: commit 8eef9123 ("arm/arm64: KVM: map MMIO regions at creation time") Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Eric Auger <eric.auger@rehat.com> Reviewed-by:
Christoffer Dall <cdall@linaro.org> [ Handle dirty page logging failure case ] Signed-off-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
David Hildenbrand authored
commit 90db1043 upstream. No caller currently checks the return value of kvm_io_bus_unregister_dev(). This is evil, as all callers silently go on freeing their device. A stale reference will remain in the io_bus, getting at least used again, when the iobus gets teared down on kvm_destroy_vm() - leading to use after free errors. There is nothing the callers could do, except retrying over and over again. So let's simply remove the bus altogether, print an error and make sure no one can access this broken bus again (returning -ENOMEM on any attempt to access it). Fixes: e93f8a0f ("KVM: convert io_bus to SRCU") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Reviewed-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Peter Xu authored
commit df630b8c upstream. When releasing the bus, let's clear the bus pointers to mark it out. If any further device unregister happens on this bus, we know that we're done if we found the bus being released already. Signed-off-by:
Peter Xu <peterx@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Thomas Huth authored
commit 708e75a3 upstream. If kvmppc_handle_exit_pr() calls kvmppc_emulate_instruction() to emulate one instruction (in the BOOK3S_INTERRUPT_H_EMUL_ASSIST case), it calls kvmppc_core_queue_program() afterwards if kvmppc_emulate_instruction() returned EMULATE_FAIL, so the guest gets an program interrupt for the illegal opcode. However, the kvmppc_emulate_instruction() also tried to inject a program exception for this already, so the program interrupt gets injected twice and the return address in srr0 gets destroyed. All other callers of kvmppc_emulate_instruction() are also injecting a program interrupt, and since the callers have the right knowledge about the srr1 flags that should be used, it is the function kvmppc_emulate_instruction() that should _not_ inject program interrupts, so remove the kvmppc_core_queue_program() here. This fixes the issue discovered by Laurent Vivier with kvm-unit-tests where the logs are filled with these messages when the test tries to execute an illegal instruction: Couldn't emulate instruction 0x00000000 (op 0 xop 0) kvmppc_handle_exit_pr: emulation at 700 failed (00000000) Signed-off-by:
Thomas Huth <thuth@redhat.com> Reviewed-by:
Alexander Graf <agraf@suse.de> Tested-by:
Laurent Vivier <lvivier@redhat.com> Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
-
Roman Mashak authored
commit edb9d1bf upstream. When tc actions are loaded as a module and no actions have been installed, flushing them would result in actions removed from the memory, but modules reference count not being decremented, so that the modules would not be unloaded. Following is example with GACT action: % sudo modprobe act_gact % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions ls action gact % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 1 % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 2 % sudo rmmod act_gact rmmod: ERROR: Module act_gact is in use .... After the fix: % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions add action pass index 1 % sudo tc actions add action pass index 2 % sudo tc actions add action pass index 3 % lsmod Module Size Used by act_gact 16384 3 % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 0 % % sudo tc actions flush action gact % lsmod Module Size Used by act_gact 16384 0 % sudo rmmod act_gact % lsmod Module Size Used by % Fixes: f97017cd ("net-sched: Fix actions flushing") Signed-off-by:
Roman Mashak <mrv@mojatatu.com> Signed-off-by:
Jamal Hadi Salim <jhs@mojatatu.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Marcelo Ricardo Leitner authored
commit dfcb9f4f upstream. commit 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") attempted to avoid a BUG_ON call when the association being used for a sendmsg() is blocked waiting for more sndbuf and another thread did a peeloff operation on such asoc, moving it to another socket. As Ben Hutchings noticed, then in such case it would return without locking back the socket and would cause two unlocks in a row. Further analysis also revealed that it could allow a double free if the application managed to peeloff the asoc that is created during the sendmsg call, because then sctp_sendmsg() would try to free the asoc that was created only for that call. This patch takes another approach. It will deny the peeloff operation if there is a thread sleeping on the asoc, so this situation doesn't exist anymore. This avoids the issues described above and also honors the syscalls that are already being handled (it can be multiple sendmsg calls). Joint work with Xin Long. Fixes: 2dcab598 ("sctp: avoid BUG_ON on sctp_wait_for_sndbuf") Cc: Alexander Popov <alex.popov@linux.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Mantas M authored
commit c2ed1880 upstream. The protocol field is checked when deleting IPv4 routes, but ignored for IPv6, which causes problems with routing daemons accidentally deleting externally set routes (observed by multiple bird6 users). This can be verified using `ip -6 route del <prefix> proto something`. Signed-off-by:
Mantas Mikulėnas <grawity@gmail.com> Signed-off-by:
-
Ben Hutchings authored
commit 2d6a0e9d upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Ben Hutchings authored
commit d4114914 upstream. Signed-off-by:
-
Ben Hutchings authored
commit 7926aff5 upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Ben Hutchings authored
commit 5593523f upstream. Allocating USB buffers on the stack is not portable, and no longer works on x86_64 (with VMAP_STACK enabled as per default). Fixes: 1da177e4 ("Linux-2.6.12-rc2") References: https://bugs.debian.org/852556Reported-by:
Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org> Tested-by:
-
Omar Sandoval authored
commit c4baad50 upstream. put_chars() stuffs the buffer it gets into an sg, but that buffer may be on the stack. This breaks with CONFIG_VMAP_STACK=y (for me, it manifested as printks getting turned into NUL bytes). Signed-off-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Amit Shah <amit.shah@redhat.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Stefan Brüns authored
commit 67b0503d upstream. The buffer allocation for the firmware data was changed in commit 43fab979 ("[media] dvb-usb: don't use stack for firmware load") but the same applies for the reset value. Fixes: 43fab979 ("[media] dvb-usb: don't use stack for firmware load") Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Cc: Ben Hutchings <ben@decadent.org.uk> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 43fab979 upstream. As reported by Marc Duponcheel <marc@offline.be>, firmware load on dvb-usb is using the stack, with is not allowed anymore on default Kernel configurations: [ 1025.958836] dvb-usb: found a 'WideView WT-220U PenType Receiver (based on ZL353)' in cold state, will try to load a firmware [ 1025.958853] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 1025.958855] dvb-usb: could not stop the USB controller CPU. [ 1025.958856] dvb-usb: error while transferring firmware (transferred size: -11, block size: 3) [ 1025.958856] dvb-usb: firmware download failed at 8 with -22 [ 1025.958867] usbcore: registered new interface driver dvb_usb_dtt200u [ 2.789902] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-zl0353-01.fw' [ 2.789905] ------------[ cut here ]------------ [ 2.789911] WARNING: CPU: 3 PID: 2196 at drivers/usb/core/hcd.c:1584 usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789912] transfer buffer not dma capable [ 2.789912] Modules linked in: btusb dvb_usb_dtt200u(+) dvb_usb_af9035(+) btrtl btbcm dvb_usb dvb_usb_v2 btintel dvb_core bluetooth rc_core rfkill x86_pkg_temp_thermal intel_powerclamp coretemp crc32_pclmul aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd drm_kms_helper syscopyarea sysfillrect pcspkr i2c_i801 sysimgblt fb_sys_fops drm i2c_smbus i2c_core r8169 lpc_ich mfd_core mii thermal fan rtc_cmos video button acpi_cpufreq processor snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd crc32c_intel ahci libahci libata xhci_pci ehci_pci xhci_hcd ehci_hcd usbcore usb_common dm_mirror dm_region_hash dm_log dm_mod [ 2.789936] CPU: 3 PID: 2196 Comm: systemd-udevd Not tainted 4.9.0-gentoo #1 [ 2.789937] Hardware name: ASUS All Series/H81I-PLUS, BIOS 0401 07/23/2013 [ 2.789938] ffffc9000339b690 ffffffff812bd397 ffffc9000339b6e0 0000000000000000 [ 2.789939] ffffc9000339b6d0 ffffffff81055c86 000006300339b6a0 ffff880116c0c000 [ 2.789941] 0000000000000000 0000000000000000 0000000000000001 ffff880116c08000 [ 2.789942] Call Trace: [ 2.789945] [<ffffffff812bd397>] dump_stack+0x4d/0x66 [ 2.789947] [<ffffffff81055c86>] __warn+0xc6/0xe0 [ 2.789948] [<ffffffff81055cea>] warn_slowpath_fmt+0x4a/0x50 [ 2.789952] [<ffffffffa006d460>] usb_hcd_map_urb_for_dma+0x430/0x560 [usbcore] [ 2.789954] [<ffffffff814ed5a8>] ? io_schedule_timeout+0xd8/0x110 [ 2.789956] [<ffffffffa006e09c>] usb_hcd_submit_urb+0x9c/0x980 [usbcore] [ 2.789958] [<ffffffff812d0ebf>] ? copy_page_to_iter+0x14f/0x2b0 [ 2.789960] [<ffffffff81126818>] ? pagecache_get_page+0x28/0x240 [ 2.789962] [<ffffffff8118c2a0>] ? touch_atime+0x20/0xa0 [ 2.789964] [<ffffffffa006f7c4>] usb_submit_urb+0x2c4/0x520 [usbcore] [ 2.789967] [<ffffffffa006feca>] usb_start_wait_urb+0x5a/0xe0 [usbcore] [ 2.789969] [<ffffffffa007000c>] usb_control_msg+0xbc/0xf0 [usbcore] [ 2.789970] [<ffffffffa067903d>] usb_cypress_writemem+0x3d/0x40 [dvb_usb] [ 2.789972] [<ffffffffa06791cf>] usb_cypress_load_firmware+0x4f/0x130 [dvb_usb] [ 2.789973] [<ffffffff8109dbbe>] ? console_unlock+0x2fe/0x5d0 [ 2.789974] [<ffffffff8109e10c>] ? vprintk_emit+0x27c/0x410 [ 2.789975] [<ffffffff8109e40a>] ? vprintk_default+0x1a/0x20 [ 2.789976] [<ffffffff81124d76>] ? printk+0x43/0x4b [ 2.789977] [<ffffffffa0679310>] dvb_usb_download_firmware+0x60/0xd0 [dvb_usb] [ 2.789979] [<ffffffffa0679898>] dvb_usb_device_init+0x3d8/0x610 [dvb_usb] [ 2.789981] [<ffffffffa069e302>] dtt200u_usb_probe+0x92/0xd0 [dvb_usb_dtt200u] [ 2.789984] [<ffffffffa007420c>] usb_probe_interface+0xfc/0x270 [usbcore] [ 2.789985] [<ffffffff8138bf95>] driver_probe_device+0x215/0x2d0 [ 2.789986] [<ffffffff8138c0e6>] __driver_attach+0x96/0xa0 [ 2.789987] [<ffffffff8138c050>] ? driver_probe_device+0x2d0/0x2d0 [ 2.789988] [<ffffffff81389ffb>] bus_for_each_dev+0x5b/0x90 [ 2.789989] [<ffffffff8138b7b9>] driver_attach+0x19/0x20 [ 2.789990] [<ffffffff8138b33c>] bus_add_driver+0x11c/0x220 [ 2.789991] [<ffffffff8138c91b>] driver_register+0x5b/0xd0 [ 2.789994] [<ffffffffa0072f6c>] usb_register_driver+0x7c/0x130 [usbcore] [ 2.789994] [<ffffffffa06a5000>] ? 0xffffffffa06a5000 [ 2.789996] [<ffffffffa06a501e>] dtt200u_usb_driver_init+0x1e/0x20 [dvb_usb_dtt200u] [ 2.789997] [<ffffffff81000408>] do_one_initcall+0x38/0x140 [ 2.789998] [<ffffffff8116001c>] ? __vunmap+0x7c/0xc0 [ 2.789999] [<ffffffff81124fb0>] ? do_init_module+0x22/0x1d2 [ 2.790000] [<ffffffff81124fe8>] do_init_module+0x5a/0x1d2 [ 2.790002] [<ffffffff810c96b1>] load_module+0x1e11/0x2580 [ 2.790003] [<ffffffff810c68b0>] ? show_taint+0x30/0x30 [ 2.790004] [<ffffffff81177250>] ? kernel_read_file+0x100/0x190 [ 2.790005] [<ffffffff810c9ffa>] SyS_finit_module+0xba/0xc0 [ 2.790007] [<ffffffff814f13e0>] entry_SYSCALL_64_fastpath+0x13/0x94 [ 2.790008] ---[ end trace c78a74e78baec6fc ]--- So, allocate the structure dynamically. Signed-off-by:
-
Kees Cook authored
commit a4866aa8 upstream. Under CONFIG_STRICT_DEVMEM, reading System RAM through /dev/mem is disallowed. However, on x86, the first 1MB was always allowed for BIOS and similar things, regardless of it actually being System RAM. It was possible for heap to end up getting allocated in low 1MB RAM, and then read by things like x86info or dd, which would trip hardened usercopy: usercopy: kernel memory exposure attempt detected from ffff880000090000 (dma-kmalloc-256) (4096 bytes) This changes the x86 exception for the low 1MB by reading back zeros for System RAM areas instead of blindly allowing them. More work is needed to extend this to mmap, but currently mmap doesn't go through usercopy, so hardened usercopy won't Oops the kernel. Reported-by:
Tommi Rantala <tommi.t.rantala@nokia.com> Tested-by:
Kees Cook <keescook@chromium.org> Cc: Brad Spengler <spender@grsecurity.net> Signed-off-by:
-
Thierry Reding authored
commit 5fa40869 upstream. Accessing the registers of the RTC block on Tegra requires the module clock to be enabled. This only works because the RTC module clock will be enabled by default during early boot. However, because the clock is unused, the CCF will disable it at late_init time. This causes the RTC to become unusable afterwards. This can easily be reproduced by trying to use the RTC: $ hwclock --rtc /dev/rtc1 This will hang the system. I ran into this by following up on a report by Martin Michlmayr that reboot wasn't working on Tegra210 systems. It turns out that the rtc-tegra driver's ->shutdown() implementation will hang the CPU, because of the disabled clock, before the system can be rebooted. What confused me for a while is that the same driver is used on prior Tegra generations where the hang can not be observed. However, as Peter De Schrijver pointed out, this is because on 32-bit Tegra chips the RTC clock is enabled by the tegra20_timer.c clocksource driver, which uses the RTC to provide a persistent clock. This code is never enabled on 64-bit Tegra because the persistent clock infrastructure does not exist on 64-bit ARM. The proper fix for this is to add proper clock handling to the RTC driver in order to ensure that the clock is enabled when the driver requires it. All device trees contain the clock already, therefore no additional changes are required. Reported-by:
Martin Michlmayr <tbm@cyrius.com> Acked-By Peter De Schrijver <pdeschrijver@nvidia.com> Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> [bwh: Backported to 4.9: adjust context] Signed-off-by:
-
Lee, Chun-Yi authored
commit 98d610c3 upstream. The accelerometer event relies on the ACERWMID_EVENT_GUID notify. So, this patch changes the codes to setup accelerometer input device when detected ACERWMID_EVENT_GUID. It avoids that the accel input device created on every Acer machines. In addition, patch adds a clearly parsing logic of accelerometer hid to acer_wmi_get_handle_cb callback function. It is positive matching the "SENR" name with "BST0001" device to avoid non-supported hardware. Reported-by:
Bjørn Mork <bjorn@mork.no> Cc: Darren Hart <dvhart@infradead.org> Signed-off-by:
Lee, Chun-Yi <jlee@suse.com> [andy: slightly massage commit message] Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
Arnd Bergmann authored
commit 00514537 upstream. I ran into a stack frame size warning because of the on-stack copy of the USB device structure: drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_disconnect': drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:1029:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] Copying a device structure like this is wrong for a number of other reasons too aside from the possible stack overflow. One of them is that the dev_info() call will print the name of the device later, but AFAICT we have only copied a pointer to the name earlier and the actual name has been freed by the time it gets printed. This removes the on-stack copy of the device and instead copies the device name using kstrdup(). I'm ignoring the possible failure here as both printk() and kfree() are able to deal with NULL pointers. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Herbert Xu authored
commit ef0579b6 upstream. The ahash API modifies the request's callback function in order to clean up after itself in some corner cases (unaligned final and missing finup). When the request is complete ahash will restore the original callback and everything is fine. However, when the request gets an EBUSY on a full queue, an EINPROGRESS callback is made while the request is still ongoing. In this case the ahash API will incorrectly call its own callback. This patch fixes the problem by creating a temporary request object on the stack which is used to relay EINPROGRESS back to the original completion function. This patch also adds code to preserve the original flags value. Fixes: ab6bf4e5 ("crypto: hash - Fix the pointer voodoo in...") Reported-by:
Sabrina Dubroca <sd@queasysnail.net> Tested-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 7ed23e1b upstream. On Power8 & Power9 the early CPU inititialisation in __init_HFSCR() turns on HFSCR[TM] (Hypervisor Facility Status and Control Register [Transactional Memory]), but that doesn't take into account that TM might be disabled by CPU features, or disabled by the kernel being built with CONFIG_PPC_TRANSACTIONAL_MEM=n. So later in boot, when we have setup the CPU features, clear HSCR[TM] if the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account for the CONFIG_PPC_TRANSACTIONAL_MEM=n case. Without this a KVM guest might try use TM, even if told not to, and cause an oops in the host kernel. Typically the oops is seen in __kvmppc_vcore_entry() and may or may not be fatal to the host, but is always bad news. In practice all shipping CPU revisions do support TM, and all host kernels we are aware of build with TM support enabled, so no one should actually be able to hit this in the wild. Fixes: 2a3563b0 ("powerpc: Setup in HFSCR for POWER8") Cc: stable@vger.kernel.org # v3.10+ Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by:
Sam Bobroff <sam.bobroff@au1.ibm.com> [mpe: Rewrite change log with input from Sam, add Fixes/stable] Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> [sb: Backported to linux-4.4.y: adjusted context] Signed-off-by:
-
Minchan Kim authored
commit d72e9a7a upstream. The copy_page is optimized memcpy for page-alinged address. If it is used with non-page aligned address, it can corrupt memory which means system corruption. With zram, it can happen with 1. 64K architecture 2. partial IO 3. slub debug Partial IO need to allocate a page and zram allocates it via kmalloc. With slub debug, kmalloc(PAGE_SIZE) doesn't return page-size aligned address. And finally, copy_page(mem, cmem) corrupts memory. So, this patch changes it to memcpy. Actuaully, we don't need to change zram_bvec_write part because zsmalloc returns page-aligned address in case of PAGE_SIZE class but it's not good to rely on the internal of zsmalloc. Note: When this patch is merged to stable, clear_page should be fixed, too. Unfortunately, recent zram removes it by "same page merge" feature so it's hard to backport this patch to -stable tree. I will handle it when I receive the mail from stable tree maintainer to merge this patch to backport. Fixes: 42e99bd9 ("zram: optimize memory operations with clear_page()/copy_page()") Link: http://lkml.kernel.org/r/1492042622-12074-2-git-send-email-minchan@kernel.orgSigned-off-by:
Minchan Kim <minchan@kernel.org> Reviewed-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Richard Genoud authored
commit 31ca2c63 upstream. If uart_flush_buffer() is called between atmel_tx_dma() and atmel_complete_tx_dma(), the circular buffer has been cleared, but not atmel_port->tx_len. That leads to a circular buffer overflow (dumping (UART_XMIT_SIZE - atmel_port->tx_len) bytes). Tested-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
Richard Genoud <richard.genoud@gmail.com> Signed-off-by:
-
Horia Geantă authored
commit 40c98cb5 upstream. RNG instantiation was previously fixed by commit 62743a41 ("crypto: caam - fix RNG init descriptor ret. code checking") while deinstantiation was not addressed. Since the descriptors used are similar, in the sense that they both end with a JUMP HALT command, checking for errors should be similar too, i.e. status code 7000_0000h should be considered successful. Fixes: 1005bccd ("crypto: caam - enable instantiation of all RNG4 state handles") Signed-off-by:
Horia Geantă <horia.geanta@nxp.com> Signed-off-by:
-
Ankur Arora authored
commit 1914f0cd upstream. This was broken in commit cd979883 ("xen/acpi-processor: fix enabling interrupts on syscore_resume"). do_suspend (from xen/manage.c) and thus xen_resume_notifier never get called on the initial-domain at resume (it is if running as guest.) The rationale for the breaking change was that upload_pm_data() potentially does blocking work in syscore_resume(). This patch addresses the original issue by scheduling upload_pm_data() to execute in workqueue context. Cc: Stanislaw Gruszka <sgruszka@redhat.com> Based-on-patch-by:
Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by:
-
John Garry authored
commit 9702c67c upstream. The total ata xfer length may not be calculated properly, in that we do not use the proper method to get an sg element dma length. According to the code comment, sg_dma_len() should be used after dma_map_sg() is called. This issue was found by turning on the SMMUv3 in front of the hisi_sas controller in hip07. Multiple sg elements were being combined into a single element, but the original first element length was being use as the total xfer length. Fixes: ff2aeb1e ("libata: convert to chained sg") Signed-off-by:
John Garry <john.garry@huawei.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
peter chang authored
commit bf33f87d upstream. The user can control the size of the next command passed along, but the value passed to the ioctl isn't checked against the usable max command size. Signed-off-by:
Peter Chang <dpf@google.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
-
Chris Leech authored
commit 6f8830f5 upstream. There's a rather long standing regression from the commit "libiscsi: Reduce locking contention in fast path" Depending on iSCSI target behavior, it's possible to hit the case in iscsi_complete_task where the task is still on a pending list (!list_empty(&task->running)). When that happens the task is removed from the list while holding the session back_lock, but other task list modification occur under the frwd_lock. That leads to linked list corruption and eventually a panicked system. Rather than back out the session lock split entirely, in order to try and keep some of the performance gains this patch adds another lock to maintain the task lists integrity. Major enterprise supported kernels have been backing out the lock split for while now, thanks to the efforts at IBM where a lab setup has the most reliable reproducer I've seen on this issue. This patch has been tested there successfully. Signed-off-by:
Chris Leech <cleech@redhat.com> Fixes: 659743b0 ("[SCSI] libiscsi: Reduce locking contention in fast path") Reported-by:
Prashantha Subbarao <psubbara@us.ibm.com> Reviewed-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by:
-
Anton Blanchard authored
commit 85e8a239 upstream. We see lpfc devices regularly fail during kexec. Fix this by adding a shutdown method which mirrors the remove method. Signed-off-by:
Anton Blanchard <anton@samba.org> Reviewed-by:
Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by:
-
Nicholas Bellinger authored
commit a04e54f2 upstream. The following fixes a divide by zero OOPs with TYPE_TAPE due to pscsi_tape_read_blocksize() failing causing a zero sd->sector_size being propigated up via dev_attrib.hw_block_size. It also fixes another long-standing bug where TYPE_TAPE and TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(), which does not call scsi_device_get() to take the device reference. Instead, rename pscsi_create_type_rom() to pscsi_create_type_nondisk() and use it for all cases. Finally, also drop a dump_stack() in pscsi_get_blocks() for non TYPE_DISK, which in modern target-core can get invoked via target_sense_desc_format() during CHECK_CONDITION. Reported-by:
Malcolm Haak <insanemal@gmail.com> Signed-off-by:
-
Michael Ellerman authored
commit 97ee351b upstream. Recent toolchains force the TOC to be 256 byte aligned. We need to enforce this alignment in the zImage linker script, otherwise pointers to our TOC variables (__toc_start) could be incorrect. If the actual start of the TOC and __toc_start don't have the same value we crash early in the zImage wrapper. Suggested-by:
Alan Modra <amodra@gmail.com> Signed-off-by:
-
Paul Mackerras authored
commit 48fe9e94 upstream. In the past, there was only one load-with-reservation instruction, lwarx, and if a program attempted a lwarx on a misaligned address, it would take an alignment interrupt and the kernel handler would emulate it as though it was lwzx, which was not really correct, but benign since it is loading the right amount of data, and the lwarx should be paired with a stwcx. to the same address, which would also cause an alignment interrupt which would result in a SIGBUS being delivered to the process. We now have 5 different sizes of load-with-reservation instruction. Of those, lharx and ldarx cause an immediate SIGBUS by luck since their entries in aligninfo[] overlap instructions which were not fixed up, but lqarx overlaps with lhz and will be emulated as such. lbarx can never generate an alignment interrupt since it only operates on 1 byte. To straighten this out and fix the lqarx case, this adds code to detect the l[hwdq]arx instructions and return without fixing them up, resulting in a SIGBUS being delivered to the process. Signed-off-by:
-
Frederic Barrat authored
commit 88b1bf72 upstream. Commit 4c6d9acc ("powerpc/mm: Add hooks for cxl") converted local TLB invalidates to global if the cxl driver is active. This is necessary because the CAPP snoops invalidations to forward them to the PSL on the cxl adapter. However one path was forgotten. native_flush_hash_range() still does local TLB invalidates, as found out the hard way recently. This patch fixes it by following the same logic as previously: if the cxl driver is active, the local TLB invalidates are 'upgraded' to global. Fixes: 4c6d9acc ("powerpc/mm: Add hooks for cxl") Signed-off-by:
Frederic Barrat <fbarrat@linux.vnet.ibm.com> Reviewed-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
-
Takashi Iwai authored
commit 2d7d5400 upstream. When a new event is queued while processing to resize the FIFO in snd_seq_fifo_clear(), it may lead to a use-after-free, as the old pool that is being queued gets removed. For avoiding this race, we need to close the pool to be deleted and sync its usage before actually deleting it. The issue was spotted by syzkaller. Reported-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit c520ff3d upstream. When snd_seq_pool_done() is called, it marks the closing flag to refuse the further cell insertions. But snd_seq_pool_done() itself doesn't clear the cells but just waits until all cells are cleared by the caller side. That is, it's racy, and this leads to the endless stall as syzkaller spotted. This patch addresses the racy by splitting the setup of pool->closing flag out of snd_seq_pool_done(), and calling it properly before snd_seq_pool_done(). BugLink: http://lkml.kernel.org/r/CACT4Y+aqqy8bZA1fFieifNxR2fAfFQQABcBHj801+u5ePV0URw@mail.gmail.comReported-and-tested-by:
-
Uwe Kleine-König authored
commit 3bd32722 upstream. On some QNAP NAS devices the rtc can wake the machine. Several people noticed that once the machine was woken this way it fails to shut down. That's because the driver fails to acknowledge the interrupt and so it keeps active and restarts the machine immediatly after shutdown. See https://bugs.debian.org/794266 for a bug report. Doing this correctly requires to interpret the INT2 flag of the first read of the STATUS1 register because this bit is cleared by read. Note this is not maximally robust though because a pending irq isn't detected when the STATUS1 register was already read (and so INT2 is not set) but the irq was not disabled. But that is a hardware imposed problem that cannot easily be fixed by software. Signed-off-by:
Uwe Kleine-König <uwe@kleine-koenig.org> Signed-off-by:
-
Uwe Kleine-König authored
commit 8e6583f1 upstream. There were two deviations from the reference manual: you have to wait half a second when POC is active and you might have to repeat initialization when POC or BLD are still set after the sequence. Note however that as POC and BLD are cleared by read the driver might not be able to detect that a reset is necessary. I don't have a good idea how to fix this. Additionally report the value read from STATUS1 to the caller. This prepares the next patch. Signed-off-by:
-
Uwe Kleine-König authored
commit fdd4bc93 in 4.4-stable. The rtc core calls the .read_alarm with all fields initialized to 0. As the s35390a driver doesn't touch some fields the returned date is interpreted as a date in January 1900. So make sure all fields are set to -1; some of them are then overwritten with the right data depending on the hardware state. In mainline this is done by commit d68778b8 ("rtc: initialize output parameter for read alarm to "uninitialized"") in the core. This is considered to dangerous for stable as it might have side effects for other rtc drivers that might for example rely on alarm->time.tm_sec being initialized to 0. Signed-off-by:
-
