This patch enables the uniperif players 2 & 3 for b2120 boards
and also adds the "simple-audio-card" device node to interconnect
the SoC sound device and the codec.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

This patch adds the DT node for the uniperif reader
IP block found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

This patch adds the DT nodes for the uniperif player
IP blocks found on STiH407 family silicon.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

This patch adds the dt node for the internal audio
codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>

This patch adds the pinctrl config for the spidf out
pins used by the sasg codec IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>

This patch adds the pinctrl config for the i2s_in pins
used by the uniperif reader IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>

This patch adds the pinctrl config for the i2s_out pins
used by the uniperif player IP.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>

These nodes are required to get the fdma driver working
on STiH407 based silicon.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>

Add the hva (multi-format video encoder for STMicroelectronics SoC)
dt nodes for the hva device, defining register address, interrupt
and clock.
Signed-off-by: Jean-Christophe TROTIN <jean-christophe.trotin@st.com>

This allows to make the board boot even if clock handling
by all drivers is not properly done.
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Allow to use the mico USB port which is driven by USB3 IP
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

Remove useless gpio-cells
Add second parameter to indicate if gpio is active high
or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>

- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
  instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
  instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
  - 1GB DDR
  - On-Board USB combo WiFi/Bluetooth RTL8723BU
    with PCB soldered antenna
  - Ethernet 1000-BaseT
  - Sata
  - HDMI
  - 2 x USB2 type A
  - micro USB2 type AB
  - SD card slot
  - High speed connector (SD/I2C/USB interfaces)
  - Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force HOST_PORTS_IMPL to 1 by using
ports-implemented DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

On 96board, we can't reuse rgmii1-mdio as the pin pio1 3
( mdint ) is dedicated for user led green 1. So create
rgmii1_mdio_1 for 96board on which only mdio and mdc pins
are useful.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

Due to 96board which uses mmc0 node for SD card, the non-removable
property must be moved from STiH407-family to board file for B2120
and B2199 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

Add missing pin muxing for I2C2 alternate 2. This
i2c2 pin muxing is dedicated for 96board high speed
expansion connector.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Correct spacing between nodes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Changed node name and added the unit address]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

cat /sys/kernel/debug/pinctrl/921f080.pin-controller-front1/pingroups
leads to the kernel warning:

[   86.083560] st-pinctrl 921f080.pin-controller-front1: failed to get pin(-517) name
[   86.091192] ------------[ cut here ]------------
[   86.095897] WARNING: CPU: 0 PID: 1579 at drivers/pinctrl/core.c:1414 pinctrl_groups_show+0x144/0x16c
[   86.105072] Modules linked in:
[   86.108127] CPU: 0 PID: 1579 Comm: cat Tainted: G        W       4.6.0-00011-g9ba82e2-dirty #5
[   86.116728] Hardware name: STiH415/416 SoC with Flattened Device Tree
[   86.123194] [<c010fa90>] (unwind_backtrace) from [<c010bea8>] (show_stack+0x10/0x14)
[   86.130943] [<c010bea8>] (show_stack) from [<c038c5b0>] (dump_stack+0x98/0xac)
[   86.138167] [<c038c5b0>] (dump_stack) from [<c0129b58>] (__warn+0xe8/0x100)
[   86.145121] [<c0129b58>] (__warn) from [<c0129c20>] (warn_slowpath_null+0x20/0x28)
[   86.152681] [<c0129c20>] (warn_slowpath_null) from [<c03bf810>] (pinctrl_groups_show+0x144/0x16c)
[   86.161550] [<c03bf810>] (pinctrl_groups_show) from [<c0218a5c>] (seq_read+0x1ec/0x4c0)
[   86.169553] [<c0218a5c>] (seq_read) from [<c01f66f0>] (__vfs_read+0x20/0xd0)
[   86.176592] [<c01f66f0>] (__vfs_read) from [<c01f7414>] (vfs_read+0x7c/0x104)
[   86.183716] [<c01f7414>] (vfs_read) from [<c01f81a0>] (SyS_read+0x44/0x9c)
[   86.190585] [<c01f81a0>] (SyS_read) from [<c0108400>] (ret_fast_syscall+0x0/0x3c)
[   86.198158] ---[ end trace 1aa2e3ae820eeb3e ]---

Move the pincontroller pio20 node above the tsin4 node, which referred
to it, fix this warning.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>

Pull more block fixes from Jens Axboe:
 "As mentioned in the pull the other day, a few more fixes for this
  round, all related to the bio op changes in this series.

  Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf.  I
  wanted to do that change right after or right before -rc1, so that
  risk of conflict was reduced.  I just rebased the series on top of
  current master, and no new ->bi_rw usage has snuck in"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: rename bio bi_rw to bi_opf
  target: iblock_execute_sync_cache() should use bio_set_op_attrs()
  mm: make __swap_writepage() use bio_set_op_attrs()
  block/mm: make bdev_ops->rw_page() take a bool for read/write

Pull drm zpos property support from Dave Airlie:
 "This tree was waiting on some media stuff I hadn't had time to get a
  stable branchpoint off, so I just waited until it was all in your tree
  first.

  It's been around a bit on the list and shouldn't affect anything
  outside adding the generic API and moving some ARM drivers to using
  it"

* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
  drm: rcar: use generic code for managing zpos plane property
  drm/exynos: use generic code for managing zpos plane property
  drm: sti: use generic zpos for plane
  drm: add generic zpos property

Since commit 63a4cc24, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.

No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>

The original commit missed this function, it needs to mark it a
write flush.

Cc: Mike Christie <mchristi@redhat.com>
Fixes: e742fc32 ("target: use bio op accessors")
Signed-off-by: Jens Axboe <axboe@fb.com>

Cleaner than manipulating bio->bi_rw flags directly.
Signed-off-by: Jens Axboe <axboe@fb.com>

Commit abf54548 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.

Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull documentation fixes from Jonathan Corbet:
 "Three fixes for the docs build, including removing an annoying warning
  on 'make help' if sphinx isn't present"

* tag 'doc-4.8-fixes' of git://git.lwn.net/linux:
  DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1
  Documenation: update cgroup's document path
  Documentation/sphinx: do not warn about missing tools in 'make help'