Some circumstances call for virtual pages, to expose multiple values
packed into an extended PMBus register in a manner non-compliant with
the PMBus standard. An example of this is the Maxim MAX31785 controller,
which extends the READ_FAN_SPEED_1 PMBus register from two to four bytes
to support tach readings for both rotors of a dual rotor fan. This extended
register contains two word-sized values, one reporting the rate of the
fastest rotor, the other the rate of the slowest. The concept of virtual
pages aids this situation by mapping the page number onto the value to be
selected from the vectored result.

We should not try to set virtual pages on the device as such a page
explicitly doesn't exist; add a flag so we can avoid doing so.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The implementation makes use of the new fan control virtual registers
exposed by the pmbus core. It mixes use of the default implementations
with some overrides via the read/write handlers to handle FAN_COMMAND_1
on the MAX31785, whose definition breaks the value range into various
control bands dependent on RPM or PWM mode.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Expose fanX_target, pwmX and pwmX_enable hwmon sysfs attributes.

Fans in a PMBus device are driven by the configuration of two registers,
FAN_CONFIG_x_y and FAN_COMMAND_x: FAN_CONFIG_x_y dictates how the fan
and the tacho operate (if installed), while FAN_COMMAND_x sets the
desired fan rate. The unit of FAN_COMMAND_x is dependent on the
operational fan mode, RPM or PWM percent duty, as determined by the
corresponding configuration in FAN_CONFIG_x_y.

The mapping of fanX_target, pwmX and pwmX_enable onto FAN_CONFIG_x_y and
FAN_COMMAND_x is implemented with the addition of virtual registers to
facilitate the necessary side-effects of each access:

1. PMBUS_VIRT_FAN_TARGET_x
2. PMBUS_VIRT_PWM_x
3. PMBUS_VIRT_PWM_ENABLE_x

Some complexity arises with the fanX_target and pwmX attributes both mapping
onto FAN_COMMAND_x: There is no general mapping between PWM percent duty and
RPM, so we can't display values in either attribute in terms of the other
(which in my mind is the intuitive, if impossible, behaviour). This problem
also affects the pwmX_enable attribute which allows userspace to switch between
full speed, manual PWM and a number of automatic control modes, possibly
including a switch to RPM behaviour (e.g. automatically adjusting PWM duty to
reach a RPM target, the behaviour of fanX_target).

The next most intuitive behaviour is for fanX_target and pwmX to simply be
independent, to retain their most recently set value even if that value is not
active on the hardware (due to switching to the alternative control mode). This
property of retaining the value independent of the hardware state has useful
results for both userspace and the kernel: Userspace always sees a sensible
value in the attribute (the last thing it was set to, as opposed to 0 or
receiving an error on read), and the kernel can use the attributes as a value
cache. This latter point eases the implementation of pwmX_enable, which can
look up the associated pmbus_sensor object, take its cached value and apply it
to hardware on changing control mode. This ensures we will not arbitrarily set
a PWM value as an RPM value or vice versa, and we can assume that the RPM or
PWM value set was sensible at least at some point in the past.

Finally, the DIRECT mode coefficients of some controllers is different between
RPM and PWM percent duty control modes, so PSC_PWM is introduced to capture the
necessary coefficients. As pmbus core had no PWM support previously PSC_FAN
continues to be used to capture the RPM DIRECT coefficients, but in order to
avoid falsely applying RPM scaling to PWM values I have introduced the
PMBUS_HAVE_PWM12 and PMB_BUS_HAVE_PWM34 feature bits. These feature bits allow
drivers to explicitly declare PWM support in order to have the attributes
exposed.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

LM25063 was never released. Drop support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.

Use pci_get_domain_bus_and_slot() with a domain number of 0 where we can't
extract the domain number. Other places, use the actual domain number from
the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

'default n' is default, so there is no need to specify it explicitly.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add documentation for the w83773g driver.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Nuvoton W83773G is a hardware monitor IC providing one local
temperature and two remote temperature sensors.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull x86 fixes from Thomas Gleixner:
 "A couple of fixlets for x86:

   - Fix the ESPFIX double fault handling for 5-level pagetables

   - Fix the commandline parsing for 'apic=' on 32bit systems and update
     documentation

   - Make zombie stack traces reliable

   - Fix kexec with stack canary

   - Fix the delivery mode for APICs which was missed when the x86
     vector management was converted to single target delivery. Caused a
     regression due to the broken hardware which ignores affinity
     settings in lowest prio delivery mode.

   - Unbreak modules when AMD memory encryption is enabled

   - Remove an unused parameter of prepare_switch_to"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Switch all APICs to Fixed delivery mode
  x86/apic: Update the 'apic=' description of setting APIC driver
  x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case
  x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR)
  x86: Remove unused parameter of prepare_switch_to
  x86/stacktrace: Make zombie stack traces reliable
  x86/mm: Unbreak modules that use the DMA API
  x86/build: Make isoimage work on Debian
  x86/espfix/64: Fix espfix double-fault handling on 5-level systems

Pull x86 page table isolation fixes from Thomas Gleixner:
 "Four patches addressing the PTI fallout as discussed and debugged
  yesterday:

   - Remove stale and pointless TLB flush invocations from the hotplug
     code

   - Remove stale preempt_disable/enable from __native_flush_tlb()

   - Plug the memory leak in the write_ldt() error path"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/ldt: Make LDT pgtable free conditional
  x86/ldt: Plug memory leak in error path
  x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()
  x86/smpboot: Remove stale TLB flush invocations

Pull timer fixes from Thomas Gleixner:
 "A pile of fixes for long standing issues with the timer wheel and the
  NOHZ code:

   - Prevent timer base confusion accross the nohz switch, which can
     cause unlocked access and data corruption

   - Reinitialize the stale base clock on cpu hotplug to prevent subtle
     side effects including rollovers on 32bit

   - Prevent an interrupt storm when the timer softirq is already
     pending caused by tick_nohz_stop_sched_tick()

   - Move the timer start tracepoint to a place where it actually makes
     sense

   - Add documentation to timerqueue functions as they caused confusion
     several times now"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timerqueue: Document return values of timerqueue_add/del()
  timers: Invoke timer_start_debug() where it makes sense
  nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()
  timers: Reinitialize per cpu bases on hotplug
  timers: Use deferrable base independent of base::nohz_active

Pull smp fixlet from Thomas Gleixner:
 "A trivial build warning fix for newer compilers"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Move inline keyword at the beginning of declaration

Pull scheduler fixes from Thomas Gleixner:
 "Three patches addressing the fallout of the CPU_ISOLATION changes
  especially with NO_HZ_FULL plus documentation of boot parameter
  dependency"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/isolation: Document boot parameters dependency on CONFIG_CPU_ISOLATION=y
  sched/isolation: Enable CONFIG_CPU_ISOLATION=y by default
  sched/isolation: Make CONFIG_NO_HZ_FULL select CONFIG_CPU_ISOLATION

Pull perf fixes from Thomas Gleixner:

 - plug a memory leak in the intel pmu init code

 - clang fixes

 - tooling fix to avoid including kernel headers

 - a fix for jvmti to generate correct debug information for inlined
   code

 - replace backtick with a regular shell function

 - fix the build in hardened environments

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel: Plug memory leak in intel_pmu_init()
  x86/asm: Allow again using asm.h when building for the 'bpf' clang target
  tools arch s390: Do not include header files from the kernel sources
  perf jvmti: Generate correct debug information for inlined code
  perf tools: Fix up build in hardened environments
  perf tools: Use shell function for perl cflags retrieval

Pull irq fixes from Thomas Gleixner:
 "A rather large update after the kaisered maintainer finally found time
  to handle regression reports.

   - The larger part addresses a regression caused by the x86 vector
     management rework.

     The reservation based model does not work reliably for MSI
     interrupts, if they cannot be masked (yes, yet another hw
     engineering trainwreck). The reason is that the reservation mode
     assigns a dummy vector when the interrupt is allocated and switches
     to a real vector when the interrupt is requested.

     If the MSI entry cannot be masked then the initialization might
     raise an interrupt before the interrupt is requested, which ends up
     as spurious interrupt and causes device malfunction and worse. The
     fix is to exclude MSI interrupts which do not support masking from
     reservation mode and assign a real vector right away.

   - Extend the extra lockdep class setup for nested interrupts with a
     class for the recently added irq_desc::request_mutex so lockdep can
     differeniate and does not emit false positive warnings.

   - A ratelimit guard for the bad irq printout so in case a bad irq
     comes back immediately the system does not drown in dmesg spam"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
  genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
  x86/vector: Use IRQD_CAN_RESERVE flag
  genirq: Introduce IRQD_CAN_RESERVE flag
  genirq/msi: Handle reactivation only on success
  gpio: brcmstb: Make really use of the new lockdep class
  genirq: Guard handle_bad_irq log messages
  kernel/irq: Extend lockdep class for request mutex

Pull objtool fixes from Thomas Gleixner:
 "Three fixlets for objtool:

   - Address two segfaults related to missing parameter and clang
     objects

   - Make it compile clean with clang"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Fix seg fault with clang-compiled objects
  objtool: Fix seg fault caused by missing parameter
  objtool: Fix Clang enum conversion warning

Pull char/misc fixes from Greg KH:
 "Here are six small fixes of some of the char/misc drivers that have
  been sent in to resolve reported issues.

  Nothing major, a binder use-after-free fix, some thunderbolt bugfixes,
  a hyper-v bugfix, and an nvmem driver fix. All of these have been in
  linux-next with no reported issues for a while"

* tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  nvmem: meson-mx-efuse: fix reading from an offset other than 0
  binder: fix proc->files use-after-free
  vmbus: unregister device_obj->channels_kset
  thunderbolt: Mask ring interrupt properly when polling starts
  MAINTAINERS: Add thunderbolt.rst to the Thunderbolt driver entry
  thunderbolt: Make pathname to force_power shorter

Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are two driver core fixes for 4.15-rc6, resolving some reported
  issues.

  The first is a cacheinfo fix for DT based systems to resolve a
  reported issue that has been around for a while, and the other is to
  resolve a regression in the kobject uevent code that showed up in
  4.15-rc1.

  Both have been in linux-next for a while with no reported issues"

* tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kobject: fix suppressing modalias in uevents delivered over netlink
  drivers: base: cacheinfo: fix cache type for non-architected system cache

Pull staging fixes from Greg KH:
 "Here are three staging driver fixes for 4.15-rc6

  The first resolves a bug in the lustre driver that came about due to a
  broken cleanup patch, due to crazy list usage in that codebase.

  The remaining two are ion driver fixes, finally getting the CMA
  interaction to work properly, resolving two regressions in that area
  of the code.

  All have been in linux-next with no reported issues for a while"

* tag 'staging-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: android: ion: Fix dma direction for dma_sync_sg_for_cpu/device
  staging: ion: Fix ion_cma_heap allocations
  staging: lustre: lnet: Fix recent breakage from list_for_each conversion

Pull TTY fix from Greg KH:
 "Here is a single tty fix for a reported issue that you wrote the patch
  for :)

  It's been in linux-next for a week or so with no reported issues"

* tag 'tty-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  n_tty: fix EXTPROC vs ICANON interaction with TIOCINQ (aka FIONREAD)

Pull USB/PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.15-rc6.

  Nothing major, but there are a number of regression fixes in here that
  resolve issues that have been reported a bunch. There are also the
  usual xhci fixes as well as a number of new usb serial device ids.

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'usb-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: xhci: Add XHCI_TRUST_TX_LENGTH for Renesas uPD720201
  xhci: Fix use-after-free in xhci debugfs
  xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate
  USB: serial: ftdi_sio: add id for Airbus DS P8GR
  usb: Add device quirk for Logitech HD Pro Webcam C925e
  usb: add RESET_RESUME for ELSA MicroLink 56K
  usbip: fix usbip bind writing random string after command in match_busid
  usbip: stub_rx: fix static checker warning on unnecessary checks
  usbip: prevent leaking socket pointer address in messages
  usbip: stub: stop printing kernel pointer addresses in messages
  usbip: vhci: stop printing kernel pointer addresses in messages
  USB: Fix off by one in type-specific length check of BOS SSP capability
  USB: serial: option: adding support for YUGA CLM920-NC5
  phy: rcar-gen3-usb2: select USB_COMMON
  phy: rockchip-typec: add pm_runtime_disable in err case
  phy: cpcap-usb: Fix platform_get_irq_byname's error checking.
  phy: tegra: fix device-tree node lookups
  USB: serial: qcserial: add Sierra Wireless EM7565
  USB: serial: option: add support for Telit ME910 PID 0x1101
  USB: chipidea: msm: fix ulpi-node lookup

The blackfin architecture has seen no maintainer action of any kind since
April 2015.  No new code, no pull requests, no acks to patches, no response
to mails, nothing.

The web site has an expired certificate (expiration Sep 2017, issued in
2013), the mailing list sees no answers either, with one exception:

  https://sourceforge.net/p/adi-buildroot/mailman/adi-buildroot-devel/
  >
  > Steven is no longer working on this for ADI. Acked by me if this works. Thanks.
  >
  > Best regards,
  > Aaron Wu
  > Analog Devices Inc.

But, Aaron doesn't seem to respond to queries either.
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull sparc bugfix from David Miller.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: repair calling incorrect hweight function from stubs

Andy prefers to be paranoid about the pagetable free in the error path of
write_ldt(). Make it conditional and warn whenever the installment of a
secondary LDT fails.
Requested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The error path in write_ldt() tries to free 'old_ldt' instead of the newly
allocated 'new_ldt', resulting in a memory leak. It also misses to clean up a
half populated LDT pagetable, which is not a leak as it gets cleaned up
when the process exits.

Free both the potentially half populated LDT pagetable and the newly
allocated LDT struct. This can be done unconditionally because once an LDT
is mapped subsequent maps will succeed, because the PTE page is already
populated and the two LDTs fit into that single page.
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: f55f0501 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1712311121340.1899@nanosSigned-off-by: Ingo Molnar <mingo@kernel.org>

The preempt_disable/enable() pair in __native_flush_tlb() was added in
commit:

  5cf0791d ("x86/mm: Disable preemption during CR3 read+write")

... to protect the UP variant of flush_tlb_mm_range().

That preempt_disable/enable() pair should have been added to the UP variant
of flush_tlb_mm_range() instead.

The UP variant was removed with commit:

  ce4a4e56 ("x86/mm: Remove the UP asm/tlbflush.h code, always use the (formerly) SMP code")

... but the preempt_disable/enable() pair stayed around.

The latest change to __native_flush_tlb() in commit:

  6fd166aa ("x86/mm: Use/Fix PCID to optimize user/kernel switches")

... added an access to a per CPU variable outside the preempt disabled
regions, which makes no sense at all. __native_flush_tlb() must always
be called with at least preemption disabled.

Remove the preempt_disable/enable() pair and add a WARN_ON_ONCE() to catch
bad callers independent of the smp_processor_id() debugging.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171230211829.679325424@linutronix.deSigned-off-by: Ingo Molnar <mingo@kernel.org>

smpboot_setup_warm_reset_vector() and smpboot_restore_warm_reset_vector()
invoke local_flush_tlb() for no obvious reason.

Digging in history revealed that the original code in the 2.1 era added
those because the code manipulated a swapper_pg_dir pagetable entry. The
pagetable manipulation was removed long ago in the 2.3 timeframe, but the
TLB flush invocations stayed around forever.

Remove them along with the pointless pr_debug()s which come from the same 2.1
change.
Reported-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20171230211829.586548655@linutronix.deSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull SCSI fixes from James Bottomley:
 "Two simple fixes, both of which cause I/O hangs.

  The storvsc one is from the hyper-v which can hang under certain hot
  add/remove conditions and the other is generally, where removing a
  target and a device in close proximity can result in the release
  method being executed twice (and subsequent list and other corruption
  and an eventual panic)"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: storvsc: Fix scsi_cmd error assignments in storvsc_handle_error
  scsi: core: check for device state in __scsi_remove_target()

Fix a seg fault which happens when an input file provided to 'objtool
orc generate' doesn't have a '.shstrtab' section (for instance, object
files produced by clang don't have this section).
Signed-off-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c0f2231683e9bed40fac1f13ce2c33b8389854bc.1514666459.git.jpoimboe@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Fix a seg fault when no parameter is provided to 'objtool orc'.
Signed-off-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/9172803ec7ebb72535bcd0b7f966ae96d515968e.1514666459.git.jpoimboe@redhat.comSigned-off-by: Ingo Molnar <mingo@kernel.org>

Pull HID fixes from Jiri Kosina:

 - two cosmetic fixes from Daniel Axtens and Hans de Goede

 - fix for I2C command mismatch fix for cp2112 driver from Eudean Sun

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: core: lower log level for unknown main item tags to warnings
  HID: holtekff: move MODULE_* parameters out of #ifdef block
  HID: cp2112: Fix I2C_BLOCK_DATA transactions

It appears that hardened gentoo enables "-fstack-check" by default for
gcc.

That doesn't work _at_all_ for the kernel, because the kernel stack
doesn't act like a user stack at all: it's much smaller, and it doesn't
auto-expand on use.  So the extra "probe one page below the stack" code
generated by -fstack-check just breaks the kernel in horrible ways,
causing infinite double faults etc.

[ I have to say, that the particular code gcc generates looks very
  stupid even for user space where it works, but that's a separate
  issue.  ]
Reported-and-tested-by: Alexander Tsoy <alexander@tsoy.me>
Reported-and-tested-by: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 page table isolation updates from Thomas Gleixner:
 "This is the final set of enabling page table isolation on x86:

   - Infrastructure patches for handling the extra page tables.

   - Patches which map the various bits and pieces which are required to
     get in and out of user space into the user space visible page
     tables.

   - The required changes to have CR3 switching in the entry/exit code.

   - Optimizations for the CR3 switching along with documentation how
     the ASID/PCID mechanism works.

   - Updates to dump pagetables to cover the user space page tables for
     W+X scans and extra debugfs files to analyze both the kernel and
     the user space visible page tables

  The whole functionality is compile time controlled via a config switch
  and can be turned on/off on the command line as well"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  x86/ldt: Make the LDT mapping RO
  x86/mm/dump_pagetables: Allow dumping current pagetables
  x86/mm/dump_pagetables: Check user space page table for WX pages
  x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
  x86/mm/pti: Add Kconfig
  x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
  x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
  x86/mm: Use INVPCID for __native_flush_tlb_single()
  x86/mm: Optimize RESTORE_CR3
  x86/mm: Use/Fix PCID to optimize user/kernel switches
  x86/mm: Abstract switching CR3
  x86/mm: Allow flushing for future ASID switches
  x86/pti: Map the vsyscall page if needed
  x86/pti: Put the LDT in its own PGD if PTI is on
  x86/mm/64: Make a full PGD-entry size hole in the memory map
  x86/events/intel/ds: Map debug buffers in cpu_entry_area
  x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
  x86/mm/pti: Map ESPFIX into user space
  x86/mm/pti: Share entry text PMD
  x86/entry: Align entry text section to PMD boundary
  ...

The return values of timerqueue_add/del() are not documented in the kernel doc
comment. Add proper documentation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: https://lkml.kernel.org/r/20171222145337.872681338@linutronix.de

The timer start debug function is called before the proper timer base is
set. As a consequence the trace data contains the stale CPU and flags
values.

Call the debug function after setting the new base and flags.

Fixes: 500462a9 ("timers: Switch to a non-cascading wheel")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Link: https://lkml.kernel.org/r/20171222145337.792907137@linutronix.de

The conditions in irq_exit() to invoke tick_nohz_irq_exit() which
subsequently invokes tick_nohz_stop_sched_tick() are:

  if ((idle_cpu(cpu) && !need_resched()) || tick_nohz_full_cpu(cpu))

If need_resched() is not set, but a timer softirq is pending then this is
an indication that the softirq code punted and delegated the execution to
softirqd. need_resched() is not true because the current interrupted task
takes precedence over softirqd.

Invoking tick_nohz_irq_exit() in this case can cause an endless loop of
timer interrupts because the timer wheel contains an expired timer, but
softirqs are not yet executed. So it returns an immediate expiry request,
which causes the timer to fire immediately again. Lather, rinse and
repeat....

Prevent that by adding a check for a pending timer soft interrupt to the
conditions in tick_nohz_stop_sched_tick() which avoid calling
get_next_timer_interrupt(). That keeps the tick sched timer on the tick and
prevents a repetitive programming of an already expired timer.
Reported-by: Sebastian Siewior <bigeasy@linutronix.d>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272156050.2431@nanos

The timer wheel bases are not (re)initialized on CPU hotplug. That leaves
them with a potentially stale clk and next_expiry valuem, which can cause
trouble then the CPU is plugged.

Add a prepare callback which forwards the clock, sets next_expiry to far in
the future and reset the control flags to a known state.

Set base->must_forward_clk so the first timer which is queued will try to
forward the clock to current jiffies.

Fixes: 500462a9 ("timers: Switch to a non-cascading wheel")
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712272152200.2431@nanos

During boot and before base::nohz_active is set in the timer bases, deferrable
timers are enqueued into the standard timer base. This works correctly as
long as base::nohz_active is false.

Once it base::nohz_active is set and a timer which was enqueued before that
is accessed the lock selector code choses the lock of the deferred
base. This causes unlocked access to the standard base and in case the
timer is removed it does not clear the pending flag in the standard base
bitmap which causes get_next_timer_interrupt() to return bogus values.

To prevent that, the deferrable timers must be enqueued in the deferrable
base, even when base::nohz_active is not set. Those deferrable timers also
need to be expired unconditional.

Fixes: 500462a9 ("timers: Switch to a non-cascading wheel")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: stable@vger.kernel.org
Cc: rt@linutronix.de
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Link: https://lkml.kernel.org/r/20171222145337.633328378@linutronix.de

The new reservation mode for interrupts assigns a dummy vector when the
interrupt is allocated and assigns a real vector when the interrupt is
requested. The reservation mode prevents vector pressure when devices with
a large amount of queues/interrupts are initialized, but only a minimal
subset of those queues/interrupts is actually used.

This mode has an issue with MSI interrupts which cannot be masked. If the
driver is not careful or the hardware emits an interrupt before the device
irq is requestd by the driver then the interrupt ends up on the dummy
vector as a spurious interrupt which can cause malfunction of the device or
in the worst case a lockup of the machine.

Change the logic for the reservation mode so that the early activation of
MSI interrupts checks whether:

 - the device is a PCI/MSI device
 - the reservation mode of the underlying irqdomain is activated
 - PCI/MSI masking is globally enabled
 - the PCI/MSI device uses either MSI-X, which supports masking, or
   MSI with the maskbit supported.

If one of those conditions is false, then clear the reservation mode flag
in the irq data of the interrupt and invoke irq_domain_activate_irq() with
the reserve argument cleared. In the x86 vector code, clear the can_reserve
flag in the vector allocation data so a subsequent free_irq() won't create
the same situation again. The interrupt stays assigned to a real vector
until pci_disable_msi() is invoked and all allocations are undone.

Fixes: 4900be83 ("x86/vector/msi: Switch to global reservation mode")
Reported-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Alexandru Chirvasitu <achirvasub@gmail.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291406420.1899@nanos
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712291409460.1899@nanos