The commit 47d3946e

	usb: dwc3: refactor gadget endpoint count calculation

refactored dwc3_gadget_init_endpoints() and in particular changed in or
out endpoint numbering to be through. It's not always convenient and
makes code a slightly harder to read.

Introduce a new temporary variable to make it easier to understand what
is going on inside the function.

While doing that, rename local variables as follows:
	u8 num	-> u8 total
	int num -> int kbytes

Replace implicit direction check via epnum with explicit use of
direction variable.

While here, replace %d to %u when compounding endpoint name since we are
using unsigned type.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If there is no UDC available, the msg register will fail and this
flag will not be set, but the driver is already added into pending
driver list, then the module removal modprobe -r can not remove
the driver from the pending list.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The USB3.0 peripheral controller on R-Car SoCs has a dedicated DMAC.
The DMAC needs a "PRD table" in system memory and the DMAC can have
four PRD tables. This patch adds support for the DMAC.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If PHY is entering Host mode, we need to enable VBUS.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If don't reorder initialization like this, we will never be able to
get a reference to ULPI PHYs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

If PHY is suspended by the time we want to issue ULPI transfers, we
will observe timeouts on the ULPI interface. In order to avoid such
issue, let's make sure PHY is resumed before issuing a ULPI transfer.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

We don't (yet) support PTM_STATUS messages so let's not reply to them
erroneously.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

maximum_speed entry was duplicated. Remove one instance.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This file will print out the name of the currently running USB Gadget
Driver. It can be read even when there are no functions loaded.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Move the code which was part of pullup() to the newly introduced
method.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Use this method to make sure we don't try to connect on speeds not
supported by the gadget driver.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Sometimes, the gadget driver we want to run has max_speed lower than
what the UDC supports. In such situations, UDC might want to make sure
we don't try to connect on speeds not supported by the gadget
driver (e.g. super-speed capable dwc3 with high-speed capable g_midi)
because that will just fail.

In order to make sure this situation never happens, we introduce a new
optional ->udc_set_speed() method which can be implemented by
interested UDC drivers.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds platform driver support for Synopsys UDC.

A new driver file (snps_udc_plat.c) is created for this purpose
where the platform driver registration is done based on OF
node.

Currently, UDC integrated into Broadcom's iProc SoCs (Northstar2
and Cygnus) work with this driver.

New members are added to the UDC data structure for having platform
device support along with extcon and phy support.

Kconfig and Makefiles are modified to select platform driver for
compilation.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The device node is used for UDCs integrated into Broadcom's
iProc family of SoCs'. The UDC is based on Synopsys Designware
Cores AHB Subsystem USB Device Controller IP.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Change the argument from NULL to a struct device for the
dma_pool_create call during dma init.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds a struct device member to UDC data structure and
makes changes to the arguments of dev_err and dev_dbg calls so that
the debug prints work for both pci and platform devices.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch renames the amd5536udc.c that has the core driver
functionality of Synopsys UDC to snps_udc_core.c

The symbols exported here can be used by any UDC driver that uses
the same Synopsys IP.
Signed-off-by: Raviteja Garimella <raviteja.garimella@broadcom.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Other unsigned properties return hexadecimal values, follow this
convention when printing b_vendor_code too. Also add newlines to
the OS Descriptor support related properties, like other sysfs
files use.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currently qw_sign requires UTF-8 character to set, but returns UTF-16
when read. This isn't obvious when simply using cat since the null
characters are not visible, but hexdump unveils the true string:

  # echo MSFT100 > os_desc/qw_sign
  # hexdump -C os_desc/qw_sign
  00000000  4d 00 53 00 46 00 54 00  31 00 30 00 30 00        |M.S.F.T.1.0.0.|

Make qw_sign symmetric by returning an UTF-8 string too. Also follow
common convention and add a new line at the end.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This commit allows a gadget that does not support SuperSpeed to indicate
that it supports LPM. It does this by setting the 'lpm_capable' flag in
the gadget structure.

If a gadget sets this, the composite gadget framework will set the
bcdUSB to 0x0201 to indicate that this supports BOS descriptors, and
also return a USB 2.0 Extension descriptor as part of the BOS descriptor
set.

See USB 2.0 LPM ECN Section 3.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Don't send the SuperSpeed USB Device Capability descriptor if
the gadget is not capable of SuperSpeed.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

There were individual waitqueues for each epfile but eps_enable
would iterate through all of them, resulting in essentially the
same wakeup time.

The waitqueue represents the function being enabled, so a central
waitqueue in ffs_data makes more sense and is less redundant.

Also use wake_up_interruptible to reflect use of
wait_event_interruptible.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This allows users to make an ioctl call as the first action on a
connection. Ex, some functions might want to get endpoint size
before making any i/os.

Previously, calling ioctls before read/write would depending on the
timing of endpoints being enabled.

ESHUTDOWN is now a possible return value and ENODEV is not, so change
docs accordingly.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

The assignment ret = ret is redundant and can be removed.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This is where all other USB ReST documentation has moved to.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Document a few details about DWC3 in order to help people report bugs
and debug DWC3.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of *always* dumping raw ctrl bytes, let's decode standard
requests which will make the lives of those debugging DWC3 quite a bit
easier.

Output will now look like so:

irq/34-dwc3-1594  [000] d..1   107.573081: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   107.573694: dwc3_ctrl_req: Set Address(Addr = 01)
irq/34-dwc3-1594  [000] d..1   107.588319: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   107.588816: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.589191: dwc3_ctrl_req: Set Configuration(Config = 3)
irq/34-dwc3-1594  [000] d..1   107.589846: dwc3_ctrl_req: Get BOS Descriptor(Index = 0, Length = 5)
irq/34-dwc3-1594  [000] d..1   107.590146: dwc3_ctrl_req: Get BOS Descriptor(Index = 0, Length = 22)
irq/34-dwc3-1594  [000] d..1   107.590546: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.590840: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 69)
irq/34-dwc3-1594  [000] d..1   107.591138: dwc3_ctrl_req: Get Configuration Descriptor(Index = 1, Length = 9)
irq/34-dwc3-1594  [000] d..1   107.591541: dwc3_ctrl_req: Get Configuration Descriptor(Index = 1, Length = 32)
irq/34-dwc3-1594  [000] d..1   107.591834: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.701005: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.721080: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.722709: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.728979: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   114.730544: dwc3_ctrl_req: Get Device Qualifier Descriptor(Index = 0, Length = 10)
irq/34-dwc3-1594  [000] d..1   115.776018: dwc3_ctrl_req: Get Configuration Descriptor(Index = 0, Length = 9)
irq/34-dwc3-1594  [000] d..1   115.776760: dwc3_ctrl_req: Set Configuration(Config = 0)
irq/34-dwc3-1594  [000] d..1   115.777676: dwc3_ctrl_req: Get Configuration(Length = 1)
irq/34-dwc3-1594  [000] d..1   115.924797: dwc3_ctrl_req: Get Device Descriptor(Index = 0, Length = 18)
irq/34-dwc3-1594  [000] d..1   115.929025: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.929566: dwc3_ctrl_req: Get String Descriptor(Index = 1, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.930911: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.931528: dwc3_ctrl_req: Get String Descriptor(Index = 2, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.932950: dwc3_ctrl_req: Get String Descriptor(Index = 0, Length = 500)
irq/34-dwc3-1594  [000] d..1   115.933533: dwc3_ctrl_req: Get String Descriptor(Index = 3, Length = 500)

Note that Class and Vendor requests won't be decoded for obvious
reasons. Those will be printed as a raw sequence of bytes.

This patch has been tested against a normal host (both Linux and
Windows) and USB30CV Chapter 9 tests.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead, we can require caller to pass a buffer for the function to
use. This cleans things quite a bit.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of going for a 512 byte buffer and using snprintf(), let's
rely on helps __string() and __assign_str() where possible.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

No functional changes, just a slight readability improvement.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Instead of printing out enqueue and dequeue pointer value as a header
to the output, let's mark the TRBs in question with 'E' and 'D'. The
output looks slightly easier to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

No functional changes, just making sure we can use these for ReST docs
later.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Currently, default vary will not accomodate superspeed endpoints
causing unexpected babble errors in the IN direction. Let's update
default 'vary' parameter so that we can maintain a "short-less"
transfer as hinted at the comment.
Reported-by: Ammy Yi <ammy.yi@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

%p will leak kernel pointers, so let's not expose the information on
dmesg and instead use %pK. %pK will only show the actual addresses if
explicitly enabled under /proc/sys/kernel/kptr_restrict.

Cc: <stable@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

"ep->udc->lock" and "udc->lock" are the same thing.  It confuses Smatch
if we don't use the same name consistently.
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

This patch adds a quirk to disable USB 2.0 MAC linestate check
during HS transmit. Refer the dwc3 databook, we can use it for
some special platforms if the linestate not reflect the expected
line state(J) during transmission.

When use this quirk, the controller implements a fixed 40-bit
TxEndDelay after the packet is given on UTMI and ignores the
linestate during the transmit of a token (during token-to-token
and token-to-data IPGAP).

On some rockchip platforms (e.g. rk3399), it requires to disable
the u2mac linestate check to decrease the SSPLIT token to SETUP
token inter-packet delay from 566ns to 466ns, and fix the issue
that FS/LS devices not recognized if inserted through USB 3.0 HUB.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Add null check before dereferencing dev->regs pointer inside
net2280_led_shutdown() function.

Addresses-Coverity-ID: 101783
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

Since usb phy core has added common code to register or unregister
extcon device, then phy-msm-usb driver does not need its own
code to register/unregister extcon device, then remove them.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>