- 23 Jul, 2024 5 commits
-
-
Eric Biggers authored
If exynos_ufs_fmp_init() did not enable FMP support, then exynos_ufs_fmp_resume() should not execute the FMP-related SMC calls. Fixes: c96499fc ("scsi: ufs: exynos: Add support for Flash Memory Protector (FMP)") Signed-off-by:
Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20240721183840.209284-1-ebiggers@kernel.orgReviewed-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Damien Le Moal authored
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT ZONES command reply buffer from ATA-ZAC devices by directly accessing the buffer in the host memory. This does not respect the default command DMA direction and causes IOMMU page faults on architectures with an IOMMU enforcing write-only mappings for DMA_FROM_DEVICE DMA driection (e.g. AMD hosts). scsi 18:0:0:0: Direct-Access-ZBC ATA WDC WSH722020AL W870 PQ: 0 ANSI: 6 scsi 18:0:0:0: SATA: handle(0x0027), sas_addr(0x300062b2083e7c40), phy(0), device_name(0x5000cca29dc35e11) scsi 18:0:0:0: enclosure logical id (0x300062b208097c40), slot(0) scsi 18:0:0:0: enclosure level(0x0000), connector name( C0.0) scsi 18:0:0:0: atapi(n), ncq(y), asyn_notify(n), smart(y), fua(y), sw_preserve(y) scsi 18:0:0:0: qdepth(32), tagged(1), scsi_level(7), cmd_que(1) sd 18:0:0:0: Attached scsi generic sg2 type 20 sd 18:0:0:0: [sdc] Host-managed zoned block device mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b200 flags=0x0050] mpt3sas 0000:41:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0021 address=0xfff9b300 flags=0x0050] mpt3sas_cm0: mpt3sas_ctl_pre_reset_handler: Releasing the trace buffer due to adapter reset. mpt3sas_cm0 fault info from func: mpt3sas_base_make_ioc_ready mpt3sas_cm0: fault_state(0x2666)! mpt3sas_cm0: sending diag reset !! mpt3sas_cm0: diag reset: SUCCESS sd 18:0:0:0: [sdc] REPORT ZONES start lba 0 failed sd 18:0:0:0: [sdc] REPORT ZONES: Result: hostbyte=DID_RESET driverbyte=DRIVER_OK sd 18:0:0:0: [sdc] 0 4096-byte logical blocks: (0 B/0 B) Avoid such issue by always mapping the buffer of REPORT ZONES commands using DMA_BIDIRECTIONAL (read+write IOMMU mapping). This is done by introducing the helper function _base_scsi_dma_map() and using this helper in _base_build_sg_scmd() and _base_build_sg_scmd_ieee() instead of calling directly scsi_dma_map(). Fixes: 471ef9d4 ("mpt3sas: Build MPI SGL LIST on GEN2 HBAs and IEEE SGL LIST on GEN3 HBAs") Cc: stable@vger.kernel.org Signed-off-by:
Damien Le Moal <dlemoal@kernel.org> Link: https://lore.kernel.org/r/20240719073913.179559-3-dlemoal@kernel.orgReviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by:
-
Damien Le Moal authored
Some firmware versions of the 9600 series SAS HBA byte-swap the REPORT ZONES command reply buffer from ATA-ZAC devices by directly accessing the buffer in the host memory. This does not respect the default command DMA direction and causes IOMMU page faults on architectures with an IOMMU enforcing write-only mappings for DMA_FROM_DEVICE DMA direction (e.g. AMD hosts), leading to the device capacity to be dropped to 0: scsi 18:0:58:0: Direct-Access-ZBC ATA WDC WSH722626AL W930 PQ: 0 ANSI: 7 scsi 18:0:58:0: Power-on or device reset occurred sd 18:0:58:0: Attached scsi generic sg9 type 20 sd 18:0:58:0: [sdj] Host-managed zoned block device mpi3mr 0000:c1:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0001 address=0xfec0c400 flags=0x0050] mpi3mr 0000:c1:00.0: AMD-Vi: Event logged [IO_PAGE_FAULT domain=0x0001 address=0xfec0c500 flags=0x0050] sd 18:0:58:0: [sdj] REPORT ZONES start lba 0 failed sd 18:0:58:0: [sdj] REPORT ZONES: Result: hostbyte=DID_SOFT_ERROR driverbyte=DRIVER_OK sd 18:0:58:0: [sdj] 0 4096-byte logical blocks: (0 B/0 B) sd 18:0:58:0: [sdj] Write Protect is off sd 18:0:58:0: [sdj] Mode Sense: 6b 00 10 08 sd 18:0:58:0: [sdj] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 18:0:58:0: [sdj] Attached SCSI disk Avoid this issue by always mapping the buffer of REPORT ZONES commands using DMA_BIDIRECTIONAL, that is, using a read-write IOMMU mapping. Suggested-by:
-
Manivannan Sadhasivam authored
UFS link is just put into hibern8 state during the 'freeze' process of the hibernation. Afterwards, the system may get powered down. But that doesn't matter during wakeup. Because during wakeup from hibernation, UFS link is again put into hibern8 state by the restore kernel and then the control is handed over to the to image kernel. So in both the places, UFS link is never turned OFF. But ufshcd_system_restore() just assumes that the link will be in OFF state and sets the link state accordingly. And this breaks hibernation wakeup: [ 2445.371335] phy phy-1d87000.phy.3: phy_power_on was called before phy_init [ 2445.427883] ufshcd-qcom 1d84000.ufshc: Controller enable failed [ 2445.427890] ufshcd-qcom 1d84000.ufshc: ufshcd_host_reset_and_restore: Host init failed -5 [ 2445.427906] ufs_device_wlun 0:0:0:49488: ufshcd_wl_resume failed: -5 [ 2445.427918] ufs_device_wlun 0:0:0:49488: PM: dpm_run_callback(): scsi_bus_restore returns -5 [ 2445.427973] ufs_device_wlun 0:0:0:49488: PM: failed to restore async: error -5 So fix the issue by removing the code that sets the link to OFF state. Cc: Anjana Hari <quic_ahari@quicinc.com> Cc: stable@vger.kernel.org # 6.3 Fixes: 88441a8d ("scsi: ufs: core: Add hibernation callbacks") Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20240718170659.201647-1-manivannan.sadhasivam@linaro.orgReviewed-by:
-
Johan Hovold authored
This reverts commit 7a6bbc28. The offending commit tried to suppress a double "Starting disk" message for some drivers, but instead started spamming the log with bogus messages every five seconds: [ 311.798956] sd 0:0:0:0: [sda] Starting disk [ 316.919103] sd 0:0:0:0: [sda] Starting disk [ 322.040775] sd 0:0:0:0: [sda] Starting disk [ 327.161140] sd 0:0:0:0: [sda] Starting disk [ 332.281352] sd 0:0:0:0: [sda] Starting disk [ 337.401878] sd 0:0:0:0: [sda] Starting disk [ 342.521527] sd 0:0:0:0: [sda] Starting disk [ 345.850401] sd 0:0:0:0: [sda] Starting disk [ 350.967132] sd 0:0:0:0: [sda] Starting disk [ 356.090454] sd 0:0:0:0: [sda] Starting disk ... on machines that do not actually stop the disk on runtime suspend (e.g. the Qualcomm sc8280xp CRD with UFS). Let's just revert for now to address the regression. Fixes: 7a6bbc28 ("scsi: sd: Do not repeat the starting disk message") Cc: stable@vger.kernel.org Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20240716161101.30692-1-johan+linaro@kernel.orgReviewed-by:
-
- 16 Jul, 2024 3 commits
-
-
Peter Wang authored
There is a deadlock when runtime suspend waits for the flush of RTC work, and the RTC work calls ufshcd_rpm_get_sync() to wait for runtime resume. Here is deadlock backtrace: kworker/0:1 D 4892.876354 10 10971 4859 0x4208060 0x8 10 0 120 670730152367 ptr f0ffff80c2e40000 0 1 0x00000001 0x000000ff 0x000000ff 0x000000ff <ffffffee5e71ddb0> __switch_to+0x1a8/0x2d4 <ffffffee5e71e604> __schedule+0x684/0xa98 <ffffffee5e71ea60> schedule+0x48/0xc8 <ffffffee5e725f78> schedule_timeout+0x48/0x170 <ffffffee5e71fb74> do_wait_for_common+0x108/0x1b0 <ffffffee5e71efe0> wait_for_completion+0x44/0x60 <ffffffee5d6de968> __flush_work+0x39c/0x424 <ffffffee5d6decc0> __cancel_work_sync+0xd8/0x208 <ffffffee5d6dee2c> cancel_delayed_work_sync+0x14/0x28 <ffffffee5e2551b8> __ufshcd_wl_suspend+0x19c/0x480 <ffffffee5e255fb8> ufshcd_wl_runtime_suspend+0x3c/0x1d4 <ffffffee5dffd80c> scsi_runtime_suspend+0x78/0xc8 <ffffffee5df93580> __rpm_callback+0x94/0x3e0 <ffffffee5df90b0c> rpm_suspend+0x2d4/0x65c <ffffffee5df91448> __pm_runtime_suspend+0x80/0x114 <ffffffee5dffd95c> scsi_runtime_idle+0x38/0x6c <ffffffee5df912f4> rpm_idle+0x264/0x338 <ffffffee5df90f14> __pm_runtime_idle+0x80/0x110 <ffffffee5e24ce44> ufshcd_rtc_work+0x128/0x1e4 <ffffffee5d6e3a40> process_one_work+0x26c/0x650 <ffffffee5d6e65c8> worker_thread+0x260/0x3d8 <ffffffee5d6edec8> kthread+0x110/0x134 <ffffffee5d616b18> ret_from_fork+0x10/0x20 Skip updating RTC if RPM state is not RPM_ACTIVE. Fixes: 6bf999e0 ("scsi: ufs: core: Add UFS RTC support") Cc: stable@vger.kernel.org # 6.9.x Signed-off-by:
Peter Wang <peter.wang@mediatek.com> Link: https://lore.kernel.org/r/20240715063831.29792-1-peter.wang@mediatek.comReviewed-by:
Bean Huo <beanhuo@micron.com> Reviewed-by:
-
Peter Wang authored
If force_reset is true, bypass quick recovery. This will shorten error recovery time. Signed-off-by:
-
Kyoungrul Kim authored
If the user sets use_mcq_mode to 0, the host will try to activate the LSDB mode unconditionally even when the LSDBS of device HCI cap is 1. This makes commands time out and causes device probing to fail. To prevent that problem, check the LSDBS cap when MCQ is not supported. Signed-off-by:
Kyoungrul Kim <k831.kim@samsung.com> Link: https://lore.kernel.org/r/20240709232520epcms2p8ebdb5c4fccc30a6221390566589bf122@epcms2p8Reviewed-by:
-
- 11 Jul, 2024 32 commits
-
-
Zhongqiu Han authored
The _ONSTACK variant should be used for on-stack completion, otherwise it will break lockdep. See also commit 6e9a4738 ("[PATCH] completions: lockdep annotate on stack completions"). Signed-off-by:
Zhongqiu Han <quic_zhonhan@quicinc.com> Link: https://lore.kernel.org/r/20240705103614.3650637-1-quic_zhonhan@quicinc.comSigned-off-by:
-
Chen Ni authored
Replace a comma between expression statements by a semicolon. Fixes: d4523bd6 ("scsi: qla2xxx: Refactor asynchronous command initialization") Signed-off-by:
Chen Ni <nichen@iscas.ac.cn> Link: https://lore.kernel.org/r/20240711005724.2358446-1-nichen@iscas.ac.cnReviewed-by:
Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by:
-
Martin K. Petersen authored
Nilesh Javali <njavali@marvell.com> says: Martin, Please apply the qla2xxx driver miscellaneous bug fixes to the scsi tree at your earliest convenience. Link: https://lore.kernel.org/r/20240710171057.35066-1-njavali@marvell.comSigned-off-by:
-
Nilesh Javali authored
Signed-off-by:
Nilesh Javali <njavali@marvell.com> Link: https://lore.kernel.org/r/20240710171057.35066-12-njavali@marvell.comReviewed-by:
-
Quinn Tran authored
On bsg timeout, hardware_lock is used as part of search for the srb. Instead, qpair lock should be used to iterate through different qpair. Cc: stable@vger.kernel.org Signed-off-by:
Quinn Tran <qutran@marvell.com> Signed-off-by:
-
Quinn Tran authored
For fabric scan, current code uses switch scan opcode and flags as the method to iterate through different commands to carry out the process. This makes it hard to read. This patch convert those opcode and flags into steps. In addition, this help reduce some duplicate code. Consolidate routines that handle GPNFT & GNNFT. Cc: stable@vger.kernel.org Signed-off-by:
-
Shreyas Deodhar authored
Bios version was popluated for FDMI response. Systems with EFI would show optrom version as 0. EFI version is populated here and BIOS version is already displayed under FDMI_HBA_BOOT_BIOS_NAME. Cc: stable@vger.kernel.org Signed-off-by:
Shreyas Deodhar <sdeodhar@marvell.com> Signed-off-by:
-
Manish Rangankar authored
During vport delete, it is observed that during unload we hit a crash because of stale entries in outstanding command array. For all these stale I/O entries, eh_abort was issued and aborted (fast_fail_io = 2009h) but I/Os could not complete while vport delete is in process of deleting. BUG: kernel NULL pointer dereference, address: 000000000000001c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI Workqueue: qla2xxx_wq qla_do_work [qla2xxx] RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0 RSP: 0018:ffffa1e1e150fc68 EFLAGS: 00010046 RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000001 RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8ce208a7a0d0 RBP: ffff8ce208a7a0d0 R08: 0000000000000000 R09: ffff8ce378aac9c8 R10: ffff8ce378aac8a0 R11: ffffa1e1e150f9d8 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8ce378aac9c8 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8d217f000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 0000002089acc000 CR4: 0000000000350ee0 Call Trace: <TASK> qla2xxx_qpair_sp_free_dma+0x417/0x4e0 ? qla2xxx_qpair_sp_compl+0x10d/0x1a0 ? qla2x00_status_entry+0x768/0x2830 ? newidle_balance+0x2f0/0x430 ? dequeue_entity+0x100/0x3c0 ? qla24xx_process_response_queue+0x6a1/0x19e0 ? __schedule+0x2d5/0x1140 ? qla_do_work+0x47/0x60 ? process_one_work+0x267/0x440 ? process_one_work+0x440/0x440 ? worker_thread+0x2d/0x3d0 ? process_one_work+0x440/0x440 ? kthread+0x156/0x180 ? set_kthread_struct+0x50/0x50 ? ret_from_fork+0x22/0x30 </TASK> Send out async logout explicitly for all the ports during vport delete. Cc: stable@vger.kernel.org Signed-off-by:
Manish Rangankar <mrangankar@marvell.com> Signed-off-by:
-
Shreyas Deodhar authored
A crash was observed while performing NPIV and FW reset, BUG: kernel NULL pointer dereference, address: 000000000000001c #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 1 PREEMPT_RT SMP NOPTI RIP: 0010:dma_direct_unmap_sg+0x51/0x1e0 RSP: 0018:ffffc90026f47b88 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000021 RCX: 0000000000000002 RDX: 0000000000000021 RSI: 0000000000000000 RDI: ffff8881041130d0 RBP: ffff8881041130d0 R08: 0000000000000000 R09: 0000000000000034 R10: ffffc90026f47c48 R11: 0000000000000031 R12: 0000000000000000 R13: 0000000000000000 R14: ffff8881565e4a20 R15: 0000000000000000 FS: 00007f4c69ed3d00(0000) GS:ffff889faac80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000000000000001c CR3: 0000000288a50002 CR4: 00000000007706e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> ? __die_body+0x1a/0x60 ? page_fault_oops+0x16f/0x4a0 ? do_user_addr_fault+0x174/0x7f0 ? exc_page_fault+0x69/0x1a0 ? asm_exc_page_fault+0x22/0x30 ? dma_direct_unmap_sg+0x51/0x1e0 ? preempt_count_sub+0x96/0xe0 qla2xxx_qpair_sp_free_dma+0x29f/0x3b0 [qla2xxx] qla2xxx_qpair_sp_compl+0x60/0x80 [qla2xxx] __qla2x00_abort_all_cmds+0xa2/0x450 [qla2xxx] The command completion was done early while aborting the commands in driver unload path but outside lock to avoid the WARN_ON condition of performing dma_free_attr within the lock. However this caused race condition while command completion via multiple paths causing system crash. Hence complete the command early in unload path but within the lock to avoid race condition. Fixes: 0367076b ("scsi: qla2xxx: Perform lockless command completion in abort path") Cc: stable@vger.kernel.org Signed-off-by:
-
Quinn Tran authored
Link up failure is observed as a result of flash read failure. Current code does not check flash read return code where it relies on FW checksum to detect the problem. Add check of flash read failure to detect the problem sooner. Reported-by:
kernel test robot <lkp@intel.com> Reported-by:
Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/202406210815.rPDRDMBi-lkp@intel.com/ Cc: stable@vger.kernel.org Signed-off-by:
-
Saurav Kashyap authored
Firmware only supports single DSDs in ELS Pass-through IOCB (0x53h), sg cnt is decided by the SCSI ML. User is not aware of the cause of an acutal error. Return the appropriate return code that will be decoded by API and application and proper error message will be displayed to user. Fixes: 6e98016c ("[SCSI] qla2xxx: Re-organized BSG interface specific code.") Cc: stable@vger.kernel.org Signed-off-by:
Saurav Kashyap <skashyap@marvell.com> Signed-off-by:
-
Shreyas Deodhar authored
Init Control Block is dereferenced incorrectly. Correctly dereference ICB Cc: stable@vger.kernel.org Signed-off-by:
-
Nilesh Javali authored
The driver load failed with error message, qla2xxx [0000:04:00.0]-ffff:0: register_localport failed: ret=ffffffef and with a kernel crash, BUG: unable to handle kernel NULL pointer dereference at 0000000000000070 Workqueue: events_unbound qla_register_fcport_fn [qla2xxx] RIP: 0010:nvme_fc_register_remoteport+0x16/0x430 [nvme_fc] RSP: 0018:ffffaaa040eb3d98 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff9dfb46b78c00 RCX: 0000000000000000 RDX: ffff9dfb46b78da8 RSI: ffffaaa040eb3e08 RDI: 0000000000000000 RBP: ffff9dfb612a0a58 R08: ffffffffaf1d6270 R09: 3a34303a30303030 R10: 34303a303030305b R11: 2078787832616c71 R12: ffff9dfb46b78dd4 R13: ffff9dfb46b78c24 R14: ffff9dfb41525300 R15: ffff9dfb46b78da8 FS: 0000000000000000(0000) GS:ffff9dfc67c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000070 CR3: 000000018da10004 CR4: 00000000000206f0 Call Trace: qla_nvme_register_remote+0xeb/0x1f0 [qla2xxx] ? qla2x00_dfs_create_rport+0x231/0x270 [qla2xxx] qla2x00_update_fcport+0x2a1/0x3c0 [qla2xxx] qla_register_fcport_fn+0x54/0xc0 [qla2xxx] Exit the qla_nvme_register_remote() function when qla_nvme_register_hba() fails and correctly validate nvme_local_port. Cc: stable@vger.kernel.org Signed-off-by:
-
Quinn Tran authored
The device does not come online when the target port is online. There were multiple RSCNs indicating multiple devices were affected. Driver is in the process of finishing a fabric scan. A new RSCN (device up) arrived at the tail end of the last fabric scan. Driver mistakenly thinks the new RSCN is being taken care of by the previous fabric scan, where this notification is cleared and not acted on. The laser needs to be blinked again to get the device to show up. To prevent driver from accidentally clearing the RSCN notification, each RSCN is given a generation value. A fabric scan will scan for that generation(s). Any new RSCN arrive after the scan start will have a new generation value. This will trigger another scan to get latest data. The RSCN notification flag will be cleared when the scan is associate to that generation. Reported-by:
-
Martin K. Petersen authored
Eric Biggers <ebiggers@kernel.org> says: Add support for Flash Memory Protector (FMP), which is the inline encryption hardware on Exynos and Exynos-based SoCs. Specifically, add support for the "traditional FMP mode" that works on many Exynos-based SoCs including gs101. This is the mode that uses "software keys" and is compatible with the upstream kernel's existing inline encryption framework in the block and filesystem layers. I plan to add support for the wrapped key support on gs101 at a later time. Tested on gs101 (specifically Pixel 6) by running the 'encrypt' group of xfstests on a filesystem mounted with the 'inlinecrypt' mount option. This patchset applies to v6.10-rc6, and it has no prerequisites that aren't already upstream. Link: https://lore.kernel.org/r/20240708235330.103590-1-ebiggers@kernel.orgSigned-off-by:
-
Eric Biggers authored
Add support for Flash Memory Protector (FMP), which is the inline encryption hardware on Exynos and Exynos-based SoCs. Specifically, add support for the "traditional FMP mode" that works on many Exynos-based SoCs including gs101. This is the mode that uses "software keys" and is compatible with the upstream kernel's existing inline encryption framework in the block and filesystem layers. I plan to add support for the wrapped key support on gs101 at a later time. Tested on gs101 (specifically Pixel 6) by running the 'encrypt' group of xfstests on a filesystem mounted with the 'inlinecrypt' mount option. Signed-off-by:
Peter Griffin <peter.griffin@linaro.org> Tested-by:
Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by:
-
Eric Biggers authored
Since the nonstandard inline encryption support on Exynos SoCs requires that raw cryptographic keys be copied into the PRDT, it is desirable to zeroize those keys after each request to keep them from being left in memory. Therefore, add a quirk bit that enables the zeroization. We could instead do the zeroization unconditionally. However, using a quirk bit avoids adding the zeroization overhead to standard devices. Reviewed-by:
-
Eric Biggers authored
Add a variant op to allow host drivers to initialize nonstandard crypto-related fields in the PRDT. This is needed to support inline encryption on the "Exynos" UFS controller. Note that this will be used together with the support for overriding the PRDT entry size that was already added by commit ada1e653 ("scsi: ufs: core: Allow UFS host drivers to override the sg entry size"). Reviewed-by:
-
Eric Biggers authored
Add UFSHCD_QUIRK_BROKEN_CRYPTO_ENABLE which tells the UFS core to not use the crypto enable bit defined by the UFS specification. This is needed to support inline encryption on the "Exynos" UFS controller. Reviewed-by:
-
Eric Biggers authored
Fold ufshcd_clear_keyslot() into its only remaining caller. Reviewed-by:
-
Eric Biggers authored
Add UFSHCD_QUIRK_CUSTOM_CRYPTO_PROFILE which lets UFS host drivers initialize the blk_crypto_profile themselves rather than have it be initialized by ufshcd-core according to the UFSHCI standard. This is needed to support inline encryption on the "Exynos" UFS controller which has a nonstandard interface. Reviewed-by:
-
Martin K. Petersen authored
Bart Van Assche <bvanassche@acm.org> says: Hi Martin, Please consider this series of UFS driver patches for the next merge window. Thank you, Bart. Link: https://lore.kernel.org/r/20240708211716.2827751-1-bvanassche@acm.orgSigned-off-by:
-
Martin K. Petersen authored
Pull in my fixes branch to resolve an mpi3mr merge conflict reported by sfr. Signed-off-by: -
Bart Van Assche authored
UFSHCI controllers that are compliant with the UFSHCI 4.0 standard report the maximum number of supported commands in the controller capabilities register. Use that value if .get_hba_mac == NULL. Reviewed-by:
-
Bart Van Assche authored
Make ufshcd_mcq_decide_queue_depth() easier to read by inlining ufshcd_mcq_vops_get_hba_mac(). Reviewed-by:
-
Bart Van Assche authored
Move the ufshcd_mcq_enable() call from inside ufshcd_config_mcq() to the callers of this function. No functionality is changed by this patch. This patch makes a later patch easier to read ("scsi: ufs: Make .get_hba_mac() optional"). Cc: Peter Wang <peter.wang@mediatek.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: -
Bart Van Assche authored
Move the "hba->mcq_enabled = true" assignment to prevent that it gets duplicated by a later patch that will introduce more ufshcd_mcq_enable() calls. No functionality is changed by this patch. Signed-off-by:
-
Bart Van Assche authored
Improve code readability by inlining is_mcq_enabled(). Cc: Peter Wang <peter.wang@mediatek.com> Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
Bart Van Assche authored
Move the hba->reserved_slot and the host->can_queue assignments from ufshcd_config_mcq() into ufshcd_alloc_mcq(). The advantages of this change are as follows: - It becomes easier to verify that these two parameters are updated if hba->nutrs is updated. - It prevents unnecessary assignments to these two parameters. While ufshcd_config_mcq() is called during host reset, ufshcd_alloc_mcq() is not. Cc: Can Guo <quic_cang@quicinc.com> Reviewed-by:
-
Bart Van Assche authored
Rename this constant to prepare for the introduction of the MASK_TRANSFER_REQUESTS_SLOTS_MCQ constant. The acronym "SDB" stands for "single doorbell" (mode). Reviewed-by:
-
Bart Van Assche authored
The SCSI host template members .cmd_per_lun and .can_queue are copied into the SCSI host data structure. Before these are used, these are overwritten by ufshcd_init(). Hence, this patch does not change any functionality. Reviewed-by:
Keoseong Park <keosung.park@samsung.com> Reviewed-by:
-
Bart Van Assche authored
Instead of first zero-initializing struct uic_command and next initializing it memberwise, initialize all members at once. Reviewed-by:
Daejun Park <daejun7.park@samsung.com> Reviewed-by:
Avri Altman <avri.altman@wdc.com> Reviewed-by:
-
