This adds the pintrol-da850-pupd driver to the module device table so that
udev will automatically bind the driver to the device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This simplifies error handling and allows us to drop error path handlers
completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This simplifies error handling and allows us to drop intel_pinctrl_remove()
completely.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

SoC family such as DRA7 family of processors have, in addition
to the regular muxing of pins (as done by pinctrl-single), a separate
hardware module called IODelay which is also expected to be configured.
The "IODelay" module has it's own register space that is independent
of the control module and the padconf register area.

With recent changes to the pinctrl framework, we can now support
this hardware with a reasonably minimal driver by using #pinctrl-cells,
GENERIC_PINCTRL_GROUPS and GENERIC_PINMUX_FUNCTIONS.

It is advocated strongly in TI's official documentation considering
the existing design of the DRA7 family of processors during mux or
IODelay reconfiguration, there is a potential for a significant glitch
which may cause functional impairment to certain hardware. It is
hence recommended to do as little of muxing as absolutely necessary
without I/O isolation (which can only be done in initial stages of
bootloader).

NOTE: with the system wide I/O isolation scheme present in DRA7 SoC
family, it is not reasonable to do stop all I/O operations for every
such pad configuration scheme. So, we will let it glitch when used in
this mode.

Even with the above limitation, certain functionality such as MMC has
mandatory need for IODelay reconfiguration requirements, depending on
speed of transfer. In these cases, with careful examination of usecase
involved, the expected glitch can be controlled such that it does not
impact functionality.

In short, IODelay module support as a padconf driver being introduced
here is not expected to do SoC wide I/O Isolation and is meant for
a limited subset of IODelay configuration requirements that need to
be dynamic and whose glitchy behavior will not cause functionality
failure for that interface.

IMPORTANT NOTE: we take the approach of keeping LOCK_BITs cleared
to 0x0 at all times, even when configuring Manual IO Timing Modes.
This is done by eliminating the LOCK_BIT=1 setting from Step
of the Manual IO timing Mode configuration procedure. This option
leaves the CFG_* registers unprotected from unintended writes to the
CTRL_CORE_PAD_* registers while Manual IO Timing Modes are configured.

This approach is taken to allow for a generic driver to exist in kernel
world that has to be used carefully in required usecases.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[tony@atomide.com: updated to use generic pinctrl functions, added
 binding documentation, updated comments]
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If the pin controller driver is using devm_kzalloc, there may not be
anything to do for dt_free_map. Let's make it optional to avoid
unncessary boilerplate code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now that we have a common pinctrl driver for all the sun5i SoCs, we can
remove the old, separate drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The sun5i SoCs (A10s, A13, GR8) are all based on the same die fit in
different packages. Hence, the pins and functions available are just the
based on the same set, each SoC having a different subset.

Introduce a common pinctrl driver that supports multiple variants to allow
to put as much as we can in common.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some SoCs are either supposed to be pin compatible (A10 and A20 for
example), or are just repackaged versions of the same die (A10s, A13, GR8).

In those case, having a full blown pinctrl driver just introduces
duplication in both data size and maintainance effort.

Add a variant option to both pins and functions to be able to limit the
pins and functions described only to a subset of the SoC we support with a
given driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Commit df61b366af26 ('pinctrl: core: Use delayed work for hogs')
deferred part of the registration for pinctrl devices if the pinctrl
device has hogs. This introduced a window where if the pinctrl device
with hogs was sucessfully registered, but then unregistered again
(which could be caused by parent device being probe deferred) before
the delayed work has chanced to run, then this will cause a kernel
panic to occur because:

1. The 'pctldev->p' has not yet been initialised and when unregistering
   the pinctrl device we only check to see if it is an error value, but
   now it could also be NULL.
2. The pinctrl device may not have been added to the 'pinctrldev_list'
   list and we don't check to see if it was added before removing.

Fix up the above by checking to see if the 'pctldev->p' pointer is an
error value or NULL before putting the pinctrl device and verifying
that the pinctrl device is present in 'pinctrldev_list' before removing.

Fixes: df61b366af26 ('pinctrl: core: Use delayed work for hogs')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

3bfd4430 ("pinctrl: amd: Add support for additional GPIO")
created the following warning:

drivers/pinctrl/pinctrl-amd.c: In function 'amd_gpio_dbg_show':
drivers/pinctrl/pinctrl-amd.c:210:3: warning: 'pin_num' may be used uninitialized in this function [-Wmaybe-uninitialized]
   for (; i < pin_num; i++) {
   ^
drivers/pinctrl/pinctrl-amd.c:172:21: warning: 'i' may be used uninitialized in this function [-Wmaybe-uninitialized]
  unsigned int bank, i, pin_num;
                     ^
Fix this by adding a guarding default case for illegal
bank numbers.

Cc: S-k Shyam-sundar <Shyam-sundar.S-k@amd.com>
Cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now using function_desc structure instead of imx_pmx_func.

Also leveraging generic functions to retrieve functions count/name/groups.

The imx_free_funcs function can be removed since it is now handled by
the core driver during unregister.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Now using group_desc structure instead of imx_pin_group.

Also leveraging generic functions to retrieve groups count/name/pins.

The imx_free_pingroups function can be removed since it is now handled by
the core driver during unregister.

Finally the device tree parsing is moved after the pinctrl driver registration
since this latter initializes the radix trees.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

These four pins are for SDC4, not SDC1. They are grouped for
SDC4 later in the file so this must be a typo.
Reviewed-by: Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We can now drop the driver specific code for managing functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Replaces GENERIC_PINMUX with GENERIC_PINMUX_FUNCTIONS]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We can now drop the driver specific code for managing groups.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We can add generic helpers for function handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
[Renamed the Kconfig item and moved things around]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Rename the symbol PINCTRL_GENERIC to PINCTRL_GENERIC_GROUPS since
it all pertains to groups. Replace everywhere.

ifdef out the radix tree and the struct when not using the
generic groups.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We can add generic helpers for pin group handling for cases where the pin
controller driver does not need to use static arrays.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It confused me a bit so it may confuse others. Make it crystal
clear what is going on here for any future readers.

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Having the pin control framework call pin controller functions
before it's probe has finished is not nice as the pin controller
device driver does not yet have struct pinctrl_dev handle.

Let's fix this issue by adding deferred work for late init. This is
needed to be able to add pinctrl generic helper functions that expect
to know struct pinctrl_dev handle. Note that we now need to call
create_pinctrl() directly as we don't want to add the pin controller
to the list of controllers until the hogs are claimed. We also need
to pass the pinctrl_dev to the device tree parser functions as they
otherwise won't find the right controller at this point.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This change is inspired from the pinctrl-single architecture.

The problem with current implementation is that it isn't possible
to add/remove functions and/or groups dynamically. The radix tree
offers an easy way to do so. The intent is to offer a follow-up
patch later that will enable the use of pinctrl nodes in dt-overlays.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Otherwise can't dynamically update fields such as ngroups which can
change over time (with a dt-overlay for instance).
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Trivial fixe to spelling mistake "Ivalid" to "Invalid" in
dev_err  error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is a non-functional change, which deletes code duplication in two
of four if-if branches by reordering the checks. Functional identity
of the code change can be shown by running through the whole truth table
of boolean arguments.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add some tab in order to improve indentation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Reference to 'sys2pci_np' should be dropped in all cases here, not only in
error handling path.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This activates strict mode muxing for the STM32 pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

On Marvell mv88f6180 mpp pins range from 0 to 19 as well as from 35 to 44.
This is already fixed in commit: 9573e792

This is the documentation change for above commit.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch adds support for new Bank and adds IRQCHIP_SKIP_SET_WAKE flag.
Reviewed-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Signed-off-by: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.

Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.

We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Reference the SoC-specific compatible string in the examples as
required.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a338 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t

Pull SMP hotplug notifier removal from Thomas Gleixner:
 "This is the final cleanup of the hotplug notifier infrastructure. The
  series has been reintgrated in the last two days because there came a
  new driver using the old infrastructure via the SCSI tree.

  Summary:

   - convert the last leftover drivers utilizing notifiers

   - fixup for a completely broken hotplug user

   - prevent setup of already used states

   - removal of the notifiers

   - treewide cleanup of hotplug state names

   - consolidation of state space

  There is a sphinx based documentation pending, but that needs review
  from the documentation folks"

* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/armada-xp: Consolidate hotplug state space
  irqchip/gic: Consolidate hotplug state space
  coresight/etm3/4x: Consolidate hotplug state space
  cpu/hotplug: Cleanup state names
  cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
  staging/lustre/libcfs: Convert to hotplug state machine
  scsi/bnx2i: Convert to hotplug state machine
  scsi/bnx2fc: Convert to hotplug state machine
  cpu/hotplug: Prevent overwriting of callbacks
  x86/msr: Remove bogus cleanup from the error path
  bus: arm-ccn: Prevent hotplug callback leak
  perf/x86/intel/cstate: Prevent hotplug callback leak
  ARM/imx/mmcd: Fix broken cpu hotplug handling
  scsi: qedi: Convert to hotplug state machine