- 29 Oct, 2021 11 commits
-
-
Brian Gix authored
Synchronous version of MGMT_OP_GET_CONN_INFO Implements: hci_read_rssi_sync hci_read_tx_power_sync Signed-off-by: Brian Gix <brian.gix@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Brian Gix authored
Uses previously written: hci_write_fast_connectable_sync hci_update_scan_sync hci_update_adv_data_sync Signed-off-by: Brian Gix <brian.gix@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Brian Gix authored
This creates a synchronized Write Fast Connectable call and attaches it to the MGMT_OP_SET_FAST_CONNECTABLE management opcode. Signed-off-by: Brian Gix <brian.gix@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This make use of hci_cmd_sync_queue for MGMT_OP_START_DISCOVERY, MGMT_OP_START_SERVICE_DISCOVERY and MGMT_OP_STOP_DISCOVERY to use hci_cmd_sync_queue so they no longer depend on hdev->discov_update work to send any commands. Tested with: tools/mgmt-tester -s "Start Discovery" Test Summary ------------ Start Discovery - Not powered 1 Passed Start Discovery - Invalid parameters 1 Passed Start Discovery - Not supported 1 Passed Start Discovery - Success 1 Passed Start Discovery - Success 2 Passed Start Discovery - Power Off 1 Passed Start Discovery BREDR LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Enable) Passed Start Discovery LE - (Ext Scan Param) Passed Start Discovery - (2m, Scan Param) Passed Start Discovery - (coded, Scan Param) Passed Start Discovery - (1m, 2m, coded, Scan Param) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 14, Passed: 14 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Start Service" Test Summary ------------ Start Service Discovery - Not powered 1 Passed Start Service Discovery - Invalid parameters 1 Passed Start Service Discovery - Not supported 1 Passed Start Service Discovery - Success 1 Passed Start Service Discovery - Success 2 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 tools/mgmt-tester -s "Stop Discovery" Test Summary ------------ Stop Discovery - Success 1 Passed Stop Discovery - BR/EDR (Inquiry) Success 1 Passed Stop Discovery - Rejected 1 Passed Stop Discovery - Invalid parameters 1 Passed Stop Discovery - (Ext Scan Disable) Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This make use of hci_cmd_sync_queue when MGMT_SET_POWERED is used so all commands are run within hdev->cmd_sync_work instead of hdev->power_on_work and hdev->power_off_work. In addition to that the power on sequence now takes into account if local IRK needs to be programmed in the resolving list. Tested with: tools/mgmt-tester -s "Set powered" Test Summary ------------ Set powered on - Success Passed Set powered on - Invalid parameters 1 Passed Set powered on - Invalid parameters 2 Passed Set powered on - Invalid parameters 3 Passed Set powered on - Invalid index Passed Set powered on - Privacy and Advertising Passed Set powered off - Success Passed Set powered off - Class of Device Passed Set powered off - Invalid parameters 1 Passed Set powered off - Invalid parameters 2 Passed Set powered off - Invalid parameters 3 Passed Total: 11, Passed: 11 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This replaces the use of hci_update_background_scan with hci_update_passive_scan which runs from cmd_work_sync and deal properly with resolving list when LL privacy is enabled. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This enables advertising when LL privacy is enabled and changes the command sequence when resolving list is updated to also account for when advertising is enabled using the following sequence: If there are devices to scan: Disable Scanning -> Update Accept List -> use_ll_privacy((Disable Advertising) -> Disable Resolving List -> Update Resolving List -> Enable Resolving List -> (Enable Advertising)) -> Enable Scanning Otherwise: Disable Scanning Errors during the Update Accept List stage are handled gracefully by restoring any previous state (e.g. advertising) and disabling the use of accept list as either accept list or resolving list could not be updated. Tested with: mgmt-tester -s "LL Privacy" Test Summary ------------ LL Privacy - Add Device 1 (Add to WL) Passed LL Privacy - Add Device 2 (Add to RL) Passed LL Privacy - Add Device 3 (Enable RL) Passed LL Privacy - Add Device 4 (2 Devices to WL) Passed LL Privacy - Add Device 5 (2 Devices to RL) Passed LL Privacy - Add Device 6 (RL is full) Passed LL Privacy - Add Device 7 (WL is full) Passed LL Privacy - Add Device 8 (Disable Adv) Passed LL Privacy - Add Device 9 (Multi Adv) Passed LL Privacy - Add Device 10 (Multi Dev and Multi Adv) Passed LL Privacy - Remove Device 1 (Remove from WL) Passed LL Privacy - Remove Device 2 (Remove from RL) Passed LL Privacy - Remove Device 3 (Disable RL) Passed LL Privacy - Remove Device 4 (Disable Adv) Passed LL Privacy - Remove Device 5 (Multi Adv) Passed LL Privacy - Start Discovery 1 (Disable RL) Passed LL Privacy - Start Discovery 2 (Disable RL) Passed Total: 18, Passed: 18 (100.0%), Failed: 0, Not Run: 0 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This make use of hci_cmd_sync_queue for the following MGMT commands: Add Device Remove Device Tested with: mgmt-tester -s "Add Device" Test Summary ------------ Add Device - Invalid Params 1 Passed Add Device - Invalid Params 2 Passed Add Device - Invalid Params 3 Passed Add Device - Invalid Params 4 Passed Add Device - Success 1 Passed Add Device - Success 2 Passed Add Device - Success 3 Passed Add Device - Success 4 Passed Add Device - Success 5 Passed Add Device - Success 6 - Add to whitelist Passed Add Device - Success 7 - Add to resolv list Passed Add Device - Success 8 - Enable resolv list Passed Total: 12, Passed: 12 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.209 seconds mgmt-tester -s "Remove Device" Test Summary ------------ Remove Device - Invalid Params 1 Passed Remove Device - Invalid Params 2 Passed Remove Device - Invalid Params 3 Passed Remove Device - Success 1 Passed Remove Device - Success 2 Passed Remove Device - Success 3 Passed Remove Device - Success 4 Passed Remove Device - Success 5 Passed Remove Device - Success 6 - All Devices Passed Remove Device - Success 7 - Remove from whitelist Passed Remove Device - Success 8 - Remove from resolv list Passed Total: 11, Passed: 11 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 4.26 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This make use of hci_cmd_sync_queue for the following MGMT commands: Add Advertising Remove Advertising Add Extended Advertising Parameters Add Extended Advertising Data mgmt-tester -s "Add Advertising" Test Summary ------------ Add Advertising - Failure: LE off Passed Add Advertising - Invalid Params 1 (AD too long) Passed Add Advertising - Invalid Params 2 (Malformed len) Passed Add Advertising - Invalid Params 3 (Malformed len) Passed Add Advertising - Invalid Params 4 (Malformed len) Passed Add Advertising - Invalid Params 5 (AD too long) Passed Add Advertising - Invalid Params 6 (ScRsp too long) Passed Add Advertising - Invalid Params 7 (Malformed len) Passed Add Advertising - Invalid Params 8 (Malformed len) Passed Add Advertising - Invalid Params 9 (Malformed len) Passed Add Advertising - Invalid Params 10 (ScRsp too long) Passed Add Advertising - Rejected (Timeout, !Powered) Passed Add Advertising - Success 1 (Powered, Add Adv Inst) Passed Add Advertising - Success 2 (!Powered, Add Adv Inst) Passed Add Advertising - Success 3 (!Powered, Adv Enable) Passed Add Advertising - Success 4 (Set Adv on override) Passed Add Advertising - Success 5 (Set Adv off override) Passed Add Advertising - Success 6 (Scan Rsp Dta, Adv ok) Passed Add Advertising - Success 7 (Scan Rsp Dta, Scan ok) Passed Add Advertising - Success 8 (Connectable Flag) Passed Add Advertising - Success 9 (General Discov Flag) Passed Add Advertising - Success 10 (Limited Discov Flag) Passed Add Advertising - Success 11 (Managed Flags) Passed Add Advertising - Success 12 (TX Power Flag) Passed Add Advertising - Success 13 (ADV_SCAN_IND) Passed Add Advertising - Success 14 (ADV_NONCONN_IND) Passed Add Advertising - Success 15 (ADV_IND) Passed Add Advertising - Success 16 (Connectable -> on) Passed Add Advertising - Success 17 (Connectable -> off) Passed Add Advertising - Success 18 (Power -> off, Remove) Passed Add Advertising - Success 19 (Power -> off, Keep) Passed Add Advertising - Success 20 (Add Adv override) Passed Add Advertising - Success 21 (Timeout expires) Passed Add Advertising - Success 22 (LE -> off, Remove) Passed Add Advertising - Success (Empty ScRsp) Passed Add Advertising - Success (ScRsp only) Passed Add Advertising - Invalid Params (ScRsp too long) Passed Add Advertising - Success (ScRsp appear) Passed Add Advertising - Invalid Params (ScRsp appear long) Passed Add Advertising - Success (Appear is null) Passed Add Advertising - Success (Name is null) Passed Add Advertising - Success (Complete name) Passed Add Advertising - Success (Shortened name) Passed Add Advertising - Success (Short name) Passed Add Advertising - Success (Name + data) Passed Add Advertising - Invalid Params (Name + data) Passed Add Advertising - Success (Name+data+appear) Passed Total: 47, Passed: 47 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 2.17 seconds mgmt-tester -s "Remove Advertising" Test Summary ------------ Remove Advertising - Invalid Params 1 Passed Remove Advertising - Success 1 Passed Remove Advertising - Success 2 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0585 seconds mgmt-tester -s "Ext Adv MGMT Params" Test Summary: ------------ Ext Adv MGMT Params - Unpowered Passed Ext Adv MGMT Params - Invalid parameters Passed Ext Adv MGMT Params - Success Passed Ext Adv MGMT Params - (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0746 seconds mgmt-tester -s "Ext Adv MGMT -" Test Summary ------------ Ext Adv MGMT - Data set without Params Passed Ext Adv MGMT - AD Data (5.0) Invalid parameters Passed Ext Adv MGMT - AD Data (5.0) Success Passed Ext Adv MGMT - AD Scan Response (5.0) Success Passed Total: 4, Passed: 4 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0805 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Luiz Augusto von Dentz authored
This make use of hci_cmd_sync_queue for the following MGMT commands: Set Device Class Set Device ID Add UUID Remove UUID tools/mgmt-tester -s "Set Device Class" Test Summary ------------ Set Device Class - Success 1 Passed Set Device Class - Success 2 Passed Set Device Class - Invalid parameters 1 Passed Total: 3, Passed: 3 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0599 seconds tools/mgmt-tester -s "Set Device ID" Test Summary ------------ Set Device ID - Success 1 Passed Set Device ID - Success 2 Passed Set Device ID - Disable Passed Set Device ID - Power off and Power on Passed Set Device ID - SSP off and Power on Passed Set Device ID - Invalid Parameter Passed Total: 6, Passed: 6 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.107 seconds tools/mgmt-tester -s "Add UUID" Test Summary ------------ Add UUID - UUID-16 1 Passed Add UUID - UUID-16 multiple 1 Passed Add UUID - UUID-16 partial 1 Passed Add UUID - UUID-32 1 Passed Add UUID - UUID-32 multiple 1 Passed Add UUID - UUID-32 partial 1 Passed Add UUID - UUID-128 1 Passed Add UUID - UUID-128 multiple 1 Passed Add UUID - UUID-128 partial 1 Passed Add UUID - UUID mix Passed Total: 10, Passed: 10 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.198 seconds tools/mgmt-tester -s "Remove UUID" Test Summary ------------ Remove UUID - Success 1 Passed Remove UUID - All UUID - Success 2 Passed Remove UUID - Power Off - Success 3 Passed Remove UUID - Power Off and On - Success 4 Passed Remove UUID - Not Exist - Invalid Params 1 Passed Total: 5, Passed: 5 (100.0%), Failed: 0, Not Run: 0 Overall execution time: 0.0908 seconds Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Marcel Holtmann authored
The usage of __hci_cmd_sync() within the hdev->setup() callback allows for a nice and simple serialized execution of HCI commands. More importantly it allows for result processing before issueing the next command. With the current usage of hci_req_run() it is possible to batch up commands and execute them, but it is impossible to react to their results or errors. This is an attempt to generalize the hdev->setup() handling and provide a simple way of running multiple HCI commands from a single function context. There are multiple struct work that are decdicated to certain tasks already used right now. It is add a lot of bloat to hci_dev struct and extra handling code. So it might be possible to put all of these behind a common HCI command infrastructure and just execute the HCI commands from the same work context in a serialized fashion. For example updating the white list and resolving list can be done now without having to know the list size ahead of time. Also preparing for suspend or resume shouldn't require a state machine anymore. There are other tasks that should be simplified as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 28 Oct, 2021 1 commit
-
-
Archie Pusaka authored
If we remove one instance of adv using Set Extended Adv Enable, there is a possibility of issue occurs when processing the Command Complete event. Especially, the adv_info might not be found since we already remove it in hci_req_clear_adv_instance() -> hci_remove_adv_instance(). If that's the case, we will mistakenly proceed to remove all adv instances instead of just one single instance. This patch fixes the issue by checking the content of the HCI command instead of checking whether the adv_info is found. Signed-off-by: Archie Pusaka <apusaka@chromium.org> Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
- 25 Oct, 2021 13 commits
-
-
Sean Wang authored
add MT7921s Bluetooth support Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
The MT7961 SDIO identifier for MediaTek Bluetooth devices were being referred in the MediaTek Bluetooth driver. Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Mark-yw Chen authored
Each packet should be sent out until the device emits the TX_EMPTY signal to the host, that is firmware people suggested to add to meet the actual firmware behavior and that is compatible among all the devices. Co-developed-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
That is a preliminary patch to introduce mt7921s support. Use the register CRPLR to read packet length to make all the devices share the common logic. Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
That is a preliminary patch to introduce mt7921s support. Update register CSDIOCSR operation that is suggested from the vendor driver and is compatible to the all devices. Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
btmtksdio belongs to WIFI/BT combo chip that would serve two radios in one sdio_irq so that we have to move interrupt service to worker to ensure ISR as short as possible. The worker would serve the both Tx and Rx in a batch to effectively reduce many interrupts to the host and to avoid excessive sdio lock contention between various context (even from WiFi driver) and help to be more efficient to complete command/event transation. Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
That is a preliminary patch to introduce mt7921s support. Explicitly set WHISR as write-1-clear method to all devices that is the expected behavior the driver rely on. Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
add .set_bdaddr support Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
Rely on btmtk module to reduce duplicated code Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Sean Wang authored
Add BT_MTK module that is a preliminary patch to introduce mt7921s support to share the logic betweem btusb and btmtksdio. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Paul Cercueil authored
The entry "brcm,bcm4330-bt" was listed twice in the table. Signed-off-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Johan Hovold authored
Add the missing bulk-out endpoint sanity check to probe() to avoid division by zero in bfusb_send_frame() in case a malicious device has broken descriptors (or when doing descriptor fuzz testing). Note that USB core will reject URBs submitted for endpoints with zero wMaxPacketSize but that drivers doing packet-size calculations still need to handle this (cf. commit 2548288b ("USB: Fix: Don't skip endpoint descriptors with maxpacket=0")). Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Wang Hai authored
I got a kernel BUG report when doing fault injection test: ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:45! ... RIP: 0010:__list_del_entry_valid.cold+0x12/0x4d ... Call Trace: proto_unregister+0x83/0x220 cmtp_cleanup_sockets+0x37/0x40 [cmtp] cmtp_exit+0xe/0x1f [cmtp] do_syscall_64+0x35/0xb0 entry_SYSCALL_64_after_hwframe+0x44/0xae If cmtp_init_sockets() in cmtp_init() fails, cmtp_init() still returns success. This will cause a kernel bug when accessing uncreated ctmp related data when the module exits. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 22 Oct, 2021 1 commit
-
-
Luiz Augusto von Dentz authored
msft_opcode shall be use a vendor ogf (0x3f) but the check was swifting the bits in the wrong order due to a missing parantesis over val & 0xffff, but since the code already checks for values over 0xffff it shall not be necessary to perform that operation it now just removes which makes it work properly when setting opcodes like 0xfce1. Fixes: b8f5482c ("Bluetooth: vhci: Add support for setting msft_opcode and aosp_capable") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 20 Oct, 2021 2 commits
-
-
Kyle Copperfield authored
BCM4345 and BCM43455 devices soldered onto the PCB (non-removable), use an UART connection for Bluetooth, such as in the Pinebook Pro, and the advertised btsdio support as an SDIO function is ignored. Reviewed-by: Dragan Simic <dragan.simic@gmail.com> Signed-off-by: Kyle Copperfield <kmcopper@danwin1210.me> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Soenke Huster authored
On the reception of packets with an invalid packet type, the memory of the allocated socket buffers is never freed. Add a default case that frees these to avoid a memory leak. Fixes: afd2daa2 ("Bluetooth: Add support for virtio transport driver") Signed-off-by: Soenke Huster <soenke.huster@eknoes.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 14 Oct, 2021 1 commit
-
-
Luiz Augusto von Dentz authored
This adds a debugfs entries to set msft_opcode and aosp_capable enabling vhci to emulate controllers with MSFT/AOSP extension support. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 13 Oct, 2021 5 commits
-
-
Mark-YW.Chen authored
Driver should free `usb->setup_packet` to avoid the leak. $ cat /sys/kernel/debug/kmemleak unreferenced object 0xffffffa564a58080 (size 128): backtrace: [<000000007eb8dd70>] kmem_cache_alloc_trace+0x22c/0x384 [<000000008a44191d>] btusb_mtk_hci_wmt_sync+0x1ec/0x994 [btusb] [<00000000ca7189a3>] btusb_mtk_setup+0x6b8/0x13cc [btusb] [<00000000c6105069>] hci_dev_do_open+0x290/0x974 [bluetooth] [<00000000a583f8b8>] hci_power_on+0xdc/0x3cc [bluetooth] [<000000005d80e687>] process_one_work+0x514/0xc80 [<00000000f4d57637>] worker_thread+0x818/0xd0c [<00000000dc7bdb55>] kthread+0x2f8/0x3b8 [<00000000f9999513>] ret_from_fork+0x10/0x30 Fixes: a1c49c43 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Signed-off-by: Mark-YW.Chen <mark-yw.chen@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Wei Yongjun authored
Fault injection test reported memory leak of hci device as follows: unreferenced object 0xffff88800b858000 (size 8192): comm "kworker/0:2", pid 167, jiffies 4294955747 (age 557.148s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 ad 4e ad de .............N.. backtrace: [<0000000070eb1059>] kmem_cache_alloc_trace mm/slub.c:3208 [<00000000015eb521>] hci_alloc_dev_priv include/linux/slab.h:591 [<00000000dcfc1e21>] bpa10x_probe include/net/bluetooth/hci_core.h:1240 [<000000005d3028c7>] usb_probe_interface drivers/usb/core/driver.c:397 [<00000000cbac9243>] really_probe drivers/base/dd.c:517 [<0000000024cab3f0>] __driver_probe_device drivers/base/dd.c:751 [<00000000202135cb>] driver_probe_device drivers/base/dd.c:782 [<000000000761f2bc>] __device_attach_driver drivers/base/dd.c:899 [<00000000f7d63134>] bus_for_each_drv drivers/base/bus.c:427 [<00000000c9551f0b>] __device_attach drivers/base/dd.c:971 [<000000007f79bd16>] bus_probe_device drivers/base/bus.c:487 [<000000007bb8b95a>] device_add drivers/base/core.c:3364 [<000000009564d9ea>] usb_set_configuration drivers/usb/core/message.c:2171 [<00000000e4657087>] usb_generic_driver_probe drivers/usb/core/generic.c:239 [<0000000071ede518>] usb_probe_device drivers/usb/core/driver.c:294 [<00000000cbac9243>] really_probe drivers/base/dd.c:517 hci_alloc_dev() do not init the device's flag. And hci_free_dev() using put_device() to free the memory allocated for this device, but it calls just put_device(dev) only in case of HCI_UNREGISTER flag is set, So any error handing before hci_register_dev() success will cause memory leak. To avoid this behaviour we can using kfree() to release dev before hci_register_dev() success. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Kiran K authored
Intel Read Verision(TLV) data is parsed into a local structure variable and it contains a field for bd address. Bd address is returned only in bootloader mode and hence bd address in TLV structure needs to be validated only if controller is present in boot loader mode. Signed-off-by: Kiran K <kiran.k@intel.com> Reviewed-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Wei Yongjun authored
Fault injection test report debugfs entry leak as follows: debugfs: Directory 'hci0' with parent 'bluetooth' already present! When register_pm_notifier() failed in hci_register_dev(), the debugfs create by debugfs_create_dir() do not removed in the error handing path. Add the remove debugfs code to fix it. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
David Yang authored
The coccinelle check report: "./drivers/bluetooth/btusb.c:2239:36-42: ERROR: application of sizeof to pointer". Using the real size to fix it. Fixes: 5a87679f ("Bluetooth: btusb: Support public address configuration for MediaTek Chip.") Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: David Yang <davidcomponentone@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 12 Oct, 2021 2 commits
-
-
Luiz Augusto von Dentz authored
In order to group sockets being connected using L2CAP_MODE_EXT_FLOWCTL the pid is used but sk_peer_pid was not being initialized as it is currently only done for af_unix. Fixes: b48596d1 ("Bluetooth: L2CAP: Add get_peer_pid callback") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Nguyen Dinh Phi authored
The receive path may take the socket right before hci_sock_release(), but it may enqueue the packets to the socket queues after the call to skb_queue_purge(), therefore the socket can be destroyed without clear its queues completely. Moving these skb_queue_purge() to the hci_sock_destruct() will fix this issue, because nothing is referencing the socket at this point. Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com> Reported-by: syzbot+4c4ffd1e1094dae61035@syzkaller.appspotmail.com Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 07 Oct, 2021 3 commits
-
-
Tedd Ho-Jeong An authored
This patch fixes the controller index in the Experimental Features Changed event for the offload_codec and the quality_report features to use the actual hdev index instead of non-controller index(0xffff) so the client can receive the event and know which controller the event is for. Fixes: ad933151 ("Bluetooth: Add offload feature under experimental flag") Fixes: ae7d925b ("Bluetooth: Support the quality report events") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Tedd Ho-Jeong An authored
This patch sets the wakeup state of the vhci driver when the force_wakeup is updated. Fixes: 60edfad4 ("Bluetooth: hci_vhci: Add force_prevent_wake entry") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
Kiran K authored
Read codec capabilities only if HCI_READ_LOCAL_CODEC_CAPABILITIES command is supported. If capablities are not supported, then cache codec data without caps. Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-
- 06 Oct, 2021 1 commit
-
-
Luiz Augusto von Dentz authored
When SUSPEND_DISCONNECTING bit is set that means Disconnect is pending but the code was evaluating if the list is empty before calling hci_conn_del which does the actual cleanup and remove the connection from the list thus the bit is never cleared causing the suspend procedure to always timeout when there are connections to be disconnected: Suspend/Resume - Success 5 (Pairing - Legacy) - waiting done Set the system into Suspend via force_suspend = mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.200458 = mgmt-tester: Set the system into Suspend via force_suspend 17:03:13.205812 < HCI Command: Write Scan E.. (0x03|0x001a) plen 1 #122 [hci0] 17:03:13.213561 Scan enable: No Scans (0x00) > HCI Event: Command Complete (0x0e) plen 4 #123 [hci0] 17:03:13.214710 Write Scan Enable (0x03|0x001a) ncmd 1 Status: Success (0x00) < HCI Command: Disconnect (0x01|0x0006) plen 3 #124 [hci0] 17:03:13.215830 Handle: 42 Reason: Remote Device Terminated due to Power Off (0x15) > HCI Event: Command Status (0x0f) plen 4 #125 [hci0] 17:03:13.216602 Disconnect (0x01|0x0006) ncmd 1 Status: Success (0x00) > HCI Event: Disconnect Complete (0x05) plen 4 #126 [hci0] 17:03:13.217342 Status: Success (0x00) Handle: 42 Reason: Remote Device Terminated due to Power Off (0x15) @ MGMT Event: Device Disconn.. (0x000c) plen 8 {0x0002} [hci0] 17:03:13.217688 BR/EDR Address: 00:AA:01:01:00:00 (Intel Corporation) Reason: Connection terminated by local host for suspend (0x05) @ MGMT Event: Device Disconn.. (0x000c) plen 8 {0x0001} [hci0] 17:03:13.217688 BR/EDR Address: 00:AA:01:01:00:00 (Intel Corporation) Reason: Connection terminated by local host for suspend (0x05) Suspend/Resume - Success 5 (Pairing - Legacy) - test timed out = mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.939317 Suspend/Resume - Success 5 (Pairing - Legacy) - teardown = mgmt-tester: Suspend/Resume - Success 5 (Pairing -.. 17:03:13.947267 [ 13.284291] Bluetooth: hci0: Timed out waiting for suspend events [ 13.287324] Bluetooth: hci0: Suspend timeout bit: 6 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
-