- 27 Apr, 2014 7 commits
-
-
Heiner Kallweit authored
[ Upstream commit ecab6701 ] tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore age needs to be added to the condition. Age calculation in ipv6_create_tempaddr is different from the one in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS. This can cause age in ipv6_create_tempaddr to be less than the one in addrconf_verify and therefore unnecessary temporary address to be generated. Use age calculation as in addrconf_modify to avoid this. Signed-off-by:
Heiner Kallweit <heiner.kallweit@web.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Matthew Leach authored
[ Upstream commit dbb490b9 ] When copying in a struct msghdr from the user, if the user has set the msg_namelen parameter to a negative value it gets clamped to a valid size due to a comparison between signed and unsigned values. Ensure the syscall errors when the user passes in a negative value. Signed-off-by:
Matthew Leach <matthew.leach@arm.com> Signed-off-by:
-
Peter Boström authored
[ Upstream commit dd38743b ] With TX VLAN offload enabled the source MAC address for frames sent using the VLAN interface is currently set to the address of the real interface. This is wrong since the VLAN interface may be configured with a different address. The bug was introduced in commit 2205369a ("vlan: Fix header ops passthru when doing TX VLAN offload."). This patch sets the source address before calling the create function of the real interface. Signed-off-by:
Peter Boström <peter.bostrom@netrounds.com> Signed-off-by:
-
Sabrina Dubroca authored
[ Upstream commit c88507fb ] DST_NOCOUNT should only be used if an authorized user adds routes locally. In case of routes which are added on behalf of router advertisments this flag must not get used as it allows an unlimited number of routes getting added remotely. Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit de144391 ] Some applications didn't expect recvmsg() on a non blocking socket could return -EINTR. This possibility was added as a side effect of commit b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines"). To hit this bug, you need to be a bit unlucky, as the u->readlock mutex is usually held for very small periods. Fixes: b3ca9b02 ("net: fix multithreaded signal handling in unix recv routines") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com> Signed-off-by:
-
Linus Lüssing authored
[ Upstream commit 6565b9ee ] MLD queries are supposed to have an IPv6 link-local source address according to RFC2710, section 4 and RFC3810, section 5.1.14. This patch adds a sanity check to ignore such broken MLD queries. Without this check, such malformed MLD queries can result in a denial of service: The queries are ignored by any MLD listener therefore they will not respond with an MLD report. However, without this patch these malformed MLD queries would enable the snooping part in the bridge code, potentially shutting down the according ports towards these hosts for multicast traffic as the bridge did not learn about these listeners. Reported-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Linus Lüssing <linus.luessing@web.de> Reviewed-by:
-
Daniel Borkmann authored
[ Upstream commit c485658b ] While working on ec0223ec ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable"), we noticed that there's a skb memory leakage in the error path. Running the same reproducer as in ec0223ec and by unconditionally jumping to the error label (to simulate an error condition) in sctp_sf_do_5_1D_ce() receive path lets kmemleak detector bark about the unfreed chunk->auth_chunk skb clone: Unreferenced object 0xffff8800b8f3a000 (size 256): comm "softirq", pid 0, jiffies 4294769856 (age 110.757s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 89 ab 75 5e d4 01 58 13 00 00 00 00 00 00 00 00 ..u^..X......... backtrace: [<ffffffff816660be>] kmemleak_alloc+0x4e/0xb0 [<ffffffff8119f328>] kmem_cache_alloc+0xc8/0x210 [<ffffffff81566929>] skb_clone+0x49/0xb0 [<ffffffffa0467459>] sctp_endpoint_bh_rcv+0x1d9/0x230 [sctp] [<ffffffffa046fdbc>] sctp_inq_push+0x4c/0x70 [sctp] [<ffffffffa047e8de>] sctp_rcv+0x82e/0x9a0 [sctp] [<ffffffff815abd38>] ip_local_deliver_finish+0xa8/0x210 [<ffffffff815a64af>] nf_reinject+0xbf/0x180 [<ffffffffa04b4762>] nfqnl_recv_verdict+0x1d2/0x2b0 [nfnetlink_queue] [<ffffffffa04aa40b>] nfnetlink_rcv_msg+0x14b/0x250 [nfnetlink] [<ffffffff815a3269>] netlink_rcv_skb+0xa9/0xc0 [<ffffffffa04aa7cf>] nfnetlink_rcv+0x23f/0x408 [nfnetlink] [<ffffffff815a2bd8>] netlink_unicast+0x168/0x250 [<ffffffff815a2fa1>] netlink_sendmsg+0x2e1/0x3f0 [<ffffffff8155cc6b>] sock_sendmsg+0x8b/0xc0 [<ffffffff8155d449>] ___sys_sendmsg+0x369/0x380 What happens is that commit bbd0d598 clones the skb containing the AUTH chunk in sctp_endpoint_bh_rcv() when having the edge case that an endpoint requires COOKIE-ECHO chunks to be authenticated: ---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ----------> <------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] --------- ------------------ AUTH; COOKIE-ECHO ----------------> <-------------------- COOKIE-ACK --------------------- When we enter sctp_sf_do_5_1D_ce() and before we actually get to the point where we process (and subsequently free) a non-NULL chunk->auth_chunk, we could hit the "goto nomem_init" path from an error condition and thus leave the cloned skb around w/o freeing it. The fix is to centrally free such clones in sctp_chunk_destroy() handler that is invoked from sctp_chunk_free() after all refs have dropped; and also move both kfree_skb(chunk->auth_chunk) there, so that chunk->auth_chunk is either NULL (since sctp_chunkify() allocs new chunks through kmem_cache_zalloc()) or non-NULL with a valid skb pointer. chunk->skb and chunk->auth_chunk are the only skbs in the sctp_chunk structure that need to be handeled. While at it, we should use consume_skb() for both. It is the same as dev_kfree_skb() but more appropriately named as we are not a device but a protocol. Also, this effectively replaces the kfree_skb() from both invocations into consume_skb(). Functions are the same only that kfree_skb() assumes that the frame was being dropped after a failure (e.g. for tools like drop monitor), usage of consume_skb() seems more appropriate in function sctp_chunk_destroy() though. Fixes: bbd0d598 ("[SCTP]: Implement the receive and verification of AUTH chunk") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Vlad Yasevich <yasevich@gmail.com> Cc: Neil Horman <nhorman@tuxdriver.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
- 14 Apr, 2014 33 commits
-
-
Greg Kroah-Hartman authored
-
Mikulas Patocka authored
commit 22c73795 upstream. This patch reorders reported frequencies from the highest to the lowest, just like in other frequency drivers. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Mikulas Patocka authored
commit d82b922a upstream. The powernow-k6 driver used to read the initial multiplier from the powernow register. However, there is a problem with this: * If there was a frequency transition before, the multiplier read from the register corresponds to the current multiplier. * If there was no frequency transition since reset, the field in the register always reads as zero, regardless of the current multiplier that is set using switches on the mainboard and that the CPU is running at. The zero value corresponds to multiplier 4.5, so as a consequence, the powernow-k6 driver always assumes multiplier 4.5. For example, if we have 550MHz CPU with bus frequency 100MHz and multiplier 5.5, the powernow-k6 driver thinks that the multiplier is 4.5 and bus frequency is 122MHz. The powernow-k6 driver then sets the multiplier to 4.5, underclocking the CPU to 450MHz, but reports the current frequency as 550MHz. There is no reliable way how to read the initial multiplier. I modified the driver so that it contains a table of known frequencies (based on parameters of existing CPUs and some common overclocking schemes) and sets the multiplier according to the frequency. If the frequency is unknown (because of unusual overclocking or underclocking), the user must supply the bus speed and maximum multiplier as module parameters. This patch should be backported to all stable kernels. If it doesn't apply cleanly, change it, or ask me to change it. Signed-off-by:
-
Mikulas Patocka authored
commit e20e1d0a upstream. I found out that a system with k6-3+ processor is unstable during network server load. The system locks up or the network card stops receiving. The reason for the instability is the CPU frequency scaling. During frequency transition the processor is in "EPM Stop Grant" state. The documentation says that the processor doesn't respond to inquiry requests in this state. Consequently, coherency of processor caches and bus master devices is not maintained, causing the system instability. This patch flushes the cache during frequency transition. It fixes the instability. Other minor changes: * u64 invalue changed to unsigned long because the variable is 32-bit * move the logic to set the multiplier to a separate function powernow_k6_set_cpu_multiplier * preserve lower 5 bits of the powernow port instead of 4 (the voltage field has 5 bits) * mask interrupts when reading the multiplier, so that the port is not open during other activity (running other kernel code with the port open shouldn't cause any misbehavior, but we should better be safe and keep the port closed) This patch should be backported to all stable kernels. If it doesn't apply cleanly, change it, or ask me to change it. Signed-off-by:
-
Wei Yongjun authored
commit 89f4d45b upstream. In case of error, the function kthread_run() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Cc: Jianguo Wu <wujianguo@huawei.com> Signed-off-by:
-
Alexey Khoroshilov authored
commit 2e923a05 upstream. free_buff_list and rec_buff_list are initialized in the middle of hdpvr_probe(), but if something bad happens before that, error handling code calls hdpvr_delete(), which contains iteration over the lists (via hdpvr_free_buffers()). The patch moves the lists initialization to the beginning and by the way fixes goto label in error handling of registering videodev. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Hans Verkuil authored
commit 280847b5 upstream. Video nodes can be used at once after registration, so make sure the full initialization is done before registering them. Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com> [bwh: Backported to 3.2: adjust filename, context] Signed-off-by:
-
Soeren Moch authored
commit 414abbd2 upstream. In dvb_ringbuffer lock-less synchronizationof reader and writer threads is done with separateread and write pointers. Sincedvb_ringbuffer_flush() modifies the read pointer, this function must not be called from the writer thread. This patch removes the dvb_ringbuffer_flush() calls in the dmxdev ringbuffer write functions, this fixes Oopses "Unable to handle kernel paging request" I could observe for the call chaindvb_demux_read ->dvb_dmxdev_buffer_read -> dvb_ringbuffer_read_user -> __copy_to_user (the reader side of the ringbuffer). The flush calls at the write side are not necessary anyway since ringbuffer_flush is also called in dvb_dmxdev_buffer_read() when an error condition is set in the ringbuffer. This patch should also be applied to stable kernels. Signed-off-by:
Soeren Moch <smoch@web.de> Reviewed-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
-
Al Viro authored
commit 55ee64b3 upstream. Walking rbtree while it's modified is a Bad Idea(tm); besides, the result of find_vma() can be freed just as it's getting returned to caller. Fortunately, it's easy to fix - just take ->mmap_sem a bit earlier (and don't bother with find_vma() at all if virtp >= PAGE_OFFSET - in that case we don't even look at its result). While we are at it, what prevents VIDIOC_PREPARE_BUF calling v4l_prepare_buf() -> (e.g) vb2_ioctl_prepare_buf() -> vb2_prepare_buf() -> __buf_prepare() -> __qbuf_userptr() -> vb2_vmalloc_get_userptr() -> find_vma(), AFAICS without having taken ->mmap_sem anywhere in process? The code flow is bloody convoluted and depends on a bunch of things done by initialization, so I certainly might've missed something... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Sakari Ailus <sakari.ailus@iki.fi> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Archit Taneja <archit@ti.com> Cc: Prabhakar Lad <prabhakar.lad@ti.com> Signed-off-by:
-
Laurent Pinchart authored
commit 317efce9 upstream. When subdev registration fails the subdev v4l2_dev field is left to a non-NULL value. Later calls to v4l2_device_unregister_subdev() will consider the subdev as registered and will module_put() the subdev module without any matching module_get(). Fix this by setting the subdev v4l2_dev field to NULL in v4l2_device_register_subdev() when the function fails. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by:
-
Jacob Schloss authored
commit 98fd4857 upstream. Add the USB ID for the Kinect for Windows RGB camera so it can be used with the gspca_kinect driver. Signed-off-by:
Jacob Schloss <jacob.schloss@unlimitedautomata.com> Signed-off-by:
Antonio Ospite <ospite@studenti.unina.it> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Nithin Sujir authored
commit 9bc297ea upstream. Commit 091f0ea3 "tg3: Add New 5719 Read DMA workaround" added a workaround for TX DMA stall on the 5719. This workaround needs to be applied to the 5720 as well. Reported-by:
Roland Dreier <roland@purestorage.com> Tested-by:
Nithin Nayak Sujir <nsujir@broadcom.com> Signed-off-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
Qiang Huang <h.huangqiang@huawei.com> Signed-off-by:
-
Nithin Sujir authored
commit 44f3b503 upstream. On the 5718, 5719 and 5720 serdes devices, powering down function 0 results in all the other ports being powered down. Add code to skip function 0 power down. v2: - Modify tg3_phy_power_bug() function to use a switch instead of a complicated if statement. Suggested by Joe Perches. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit deb09dda upstream. Sandy bridge EDAC is calculating the memory size with overflow. Basically, the size field and the integer calculation is using 32 bits. More bits are needed, when the DIMM memories have high density. The net result is that memories are improperly reported there, when high-density DIMMs are used: EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 0, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800 EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 1, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800 As the number of pages value is handled at the EDAC core as unsigned ints, the driver shows the 16 GB memories at sysfs interface as 16760832 MB! The fix is simple: calculate the number of pages as unsigned 64-bits integer. After the patch, the memory size (16 GB) is properly detected: EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 0, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800 EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 1, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800 Signed-off-by:
-
Lauri Hintsala authored
commit fc108d24 upstream. Release the lock before mmc_signal_sdio_irq is called by mxs_mmc_enable_sdio_irq. Backtrace: [ 65.470000] ============================================= [ 65.470000] [ INFO: possible recursive locking detected ] [ 65.470000] 3.5.0-rc5 #2 Not tainted [ 65.470000] --------------------------------------------- [ 65.470000] ksdioirqd/mmc0/73 is trying to acquire lock: [ 65.470000] (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc] [ 65.470000] [ 65.470000] but task is already holding lock: [ 65.470000] (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc] [ 65.470000] [ 65.470000] other info that might help us debug this: [ 65.470000] Possible unsafe locking scenario: [ 65.470000] [ 65.470000] CPU0 [ 65.470000] ---- [ 65.470000] lock(&(&host->lock)->rlock#2); [ 65.470000] lock(&(&host->lock)->rlock#2); [ 65.470000] [ 65.470000] *** DEADLOCK *** [ 65.470000] [ 65.470000] May be due to missing lock nesting notation [ 65.470000] [ 65.470000] 1 lock held by ksdioirqd/mmc0/73: [ 65.470000] #0: (&(&host->lock)->rlock#2){-.-...}, at: [<bf054120>] mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc] [ 65.470000] [ 65.470000] stack backtrace: [ 65.470000] [<c0014990>] (unwind_backtrace+0x0/0xf4) from [<c005ccb8>] (__lock_acquire+0x14f8/0x1b98) [ 65.470000] [<c005ccb8>] (__lock_acquire+0x14f8/0x1b98) from [<c005d3f8>] (lock_acquire+0xa0/0x108) [ 65.470000] [<c005d3f8>] (lock_acquire+0xa0/0x108) from [<c02f671c>] (_raw_spin_lock_irqsave+0x48/0x5c) [ 65.470000] [<c02f671c>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) [ 65.470000] [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) from [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) [ 65.470000] [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) from [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) [ 65.470000] [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) from [<c003c324>] (kthread+0x8c/0x98) [ 65.470000] [<c003c324>] (kthread+0x8c/0x98) from [<c00101ac>] (kernel_thread_exit+0x0/0x8) [ 65.470000] BUG: spinlock lockup suspected on CPU#0, ksdioirqd/mmc0/73 [ 65.470000] lock: 0xc3358724, .magic: dead4ead, .owner: ksdioirqd/mmc0/73, .owner_cpu: 0 [ 65.470000] [<c0014990>] (unwind_backtrace+0x0/0xf4) from [<c01b46b0>] (do_raw_spin_lock+0x100/0x144) [ 65.470000] [<c01b46b0>] (do_raw_spin_lock+0x100/0x144) from [<c02f6724>] (_raw_spin_lock_irqsave+0x50/0x5c) [ 65.470000] [<c02f6724>] (_raw_spin_lock_irqsave+0x50/0x5c) from [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) [ 65.470000] [<bf054120>] (mxs_mmc_enable_sdio_irq+0x18/0xdc [mxs_mmc]) from [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) [ 65.470000] [<bf0541d0>] (mxs_mmc_enable_sdio_irq+0xc8/0xdc [mxs_mmc]) from [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) [ 65.470000] [<c0219b38>] (sdio_irq_thread+0x1bc/0x274) from [<c003c324>] (kthread+0x8c/0x98) [ 65.470000] [<c003c324>] (kthread+0x8c/0x98) from [<c00101ac>] (kernel_thread_exit+0x0/0x8) Reported-by:
Attila Kinali <attila@kinali.ch> Signed-off-by:
Lauri Hintsala <lauri.hintsala@bluegiga.com> Acked-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Chris Ball <cjb@laptop.org> [bwh: Backported to 3.2: - Adjust context - HW_SSP_STATUS is a simple rather than function-like macro] Signed-off-by:
-
Grazvydas Ignotas authored
commit c1c52848 upstream. omapfb does not currently set pseudo palette correctly for color depths above 16bpp, making red text invisible, command like echo -e '\e[0;31mRED' > /dev/tty1 will display nothing on framebuffer console in 24bpp mode. This is because temporary variable is declared incorrectly, fix it. Signed-off-by:
Grazvydas Ignotas <notasas@gmail.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
Florian Tobias Schandinat <FlorianSchandinat@gmx.de> Signed-off-by:
-
Nithin Sujir authored
commit df465abf upstream. Some systems that don't need wake-on-lan may choose to power down the chip on system standby. Upon resume, the power on causes the boot code to startup and initialize the hardware. On one new platform, this is causing the device to go into a bad state due to a race between the driver and boot code, once every several hundred resumes. The same race exists on open since we come up from a power on. This patch adds a wait for boot code signature at the beginning of tg3_init_hw() which is common to both cases. If there has not been a power-off or the boot code has already completed, the signature will be present and poll_fw() returns immediately. Also return immediately if the device does not have firmware. Signed-off-by:
-
Michael Chan authored
commit 091f0ea3 upstream. After Power-on-reset, the 5719's TX DMA length registers may contain uninitialized values and cause TX DMA to stall. Check for invalid values and set a register bit to flush the TX channels. The bit needs to be turned off after the DMA channels have been flushed. Signed-off-by:
-
Dan Carpenter authored
commit 3806b45b upstream. The "rpm * div" operations can overflow here, so this patch adds an upper limit to rpm to prevent that. Jean Delvare helped me with this patch. Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Roger Lucas <vt8231@hiddenengine.co.uk> Signed-off-by:
Jean Delvare <khali@linux-fr.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Henrik Rydberg authored
commit 25f2bd7f upstream. The crash reported and investigated in commit 5f4513 turned out to be caused by a change to the read interface on newer (2012) SMCs. Tests by Chris show that simply reading the data valid line is enough for the problem to go away. Additional tests show that the newer SMCs no longer wait for the number of requested bytes, but start sending data right away. Apparently the number of bytes to read is no longer specified as before, but instead found out by reading until end of data. Failure to read until end of data confuses the state machine, which eventually causes the crash. As a remedy, assuming bit0 is the read valid line, make sure there is nothing more to read before leaving the read function. Tested to resolve the original problem, and runtested on MBA3,1, MBP4,1, MBP8,2, MBP10,1, MBP10,2. The patch seems to have no effect on machines before 2012. Tested-by:
Chris Murphy <chris@cmurf.com> Signed-off-by:
Henrik Rydberg <rydberg@euromail.se> Signed-off-by:
Guenter Roeck <linux@roeck-us.net> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Guenter Roeck authored
commit 1102dcab upstream. TjMax for the CE4100 series of Atom CPUs was previously reported to be 110 degrees C. cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170, reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz" with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants to the tjmax table. Signed-off-by:
-
Guenter Roeck authored
commit 41e58a1f upstream. Atom CPUs don't have a register to retrieve TjMax. Detection so far was incomplete. Use the X86 model ID to improve it. Signed-off-by:
-
Guenter Roeck authored
commit 5592906f upstream. Document the Atom series D2000 and N2000 (Cedar Trail) as being supported. List and set TjMax for those series. Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: "R, Durgadoss" <durgadoss.r@intel.com> Signed-off-by:
-
Jean Delvare authored
commit fcc14ac1 upstream. Document the new Atom series (Tunnel Creek and Medfield) as being supported, and list TjMax for the Atom E600 series. Also enable the Atom tjmax heuristic for these Atom CPU models. Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Cc: Alexander Stein <alexander.stein@systec-electronic.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: "R, Durgadoss" <durgadoss.r@intel.com> Signed-off-by:
-
Kailang Yang authored
commit ba4c4d0a upstream. It's compatible with ALC269. Signed-off-by:
Kailang Yang <kailang@realtek.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Takashi Iwai authored
commit 6408eac2 upstream. The current code may access to the already freed object. The input device must be accessed and unregistered before freeing the top level sound object. Signed-off-by:
-
Anssi Hannula authored
commit 18e39186 upstream. hdmi_channel_allocation() tries to find a HDMI channel allocation that matches the number channels in the playback stream and contains only speakers that the HDMI sink has reported as available via EDID. If no such allocation is found, 0 (stereo audio) is used. Using CA 0 causes the audio causes the sink to discard everything except the first two channels (front left and front right). However, the sink may be capable of receiving more channels than it has speakers (and then perform downmix or discard the extra channels), in which case it is preferable to use a CA that contains extra channels than to use CA 0 which discards all the non-stereo channels. Additionally, it seems that HBR (HD) passthrough output does not work on Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes channels not present in CA). This happens with all receivers that report a 5.1 speaker mask since a HBR stream is carried on 8 channels to the codec. Add a fallback in the CA selection so that the CA channel count at least matches the stream channel count, even if the stream contains channels not present in the sink speaker descriptor. Thanks to GrimGriefer at OpenELEC forums for discovering that changing the sink speaker mask allowed HBR output. Reported-by: GrimGriefer Reported-by: Ashecrow Reported-by:
Frank Zafka <kafkaesque1978@gmail.com> Reported-by:
Peter Frühberger <fritsch@xbmc.org> Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by:
-
Torsten Schenk authored
commit 4c2aee00 upstream. Patch makes midi output buffer DMA-able by allocating it separately. Signed-off-by:
Torsten Schenk <torsten.schenk@zoho.com> Signed-off-by:
-
Torsten Schenk authored
commit 5ece263f upstream. Patch makes pcm buffers DMA-able by allocating each one separately. Signed-off-by:
-
Jussi Kivilinna authored
commit ddb6b5a9 upstream. Patch fixes 6fire not to use stack as URB transfer_buffer. URB buffers need to be DMA-able, which stack is not. Furthermore, transfer_buffer should not be allocated as part of larger device structure because DMA coherency issues and patch fixes this issue too. Signed-off-by:
Jussi Kivilinna <jussi.kivilinna@iki.fi> Tested-by:
-
Dan Carpenter authored
commit bd5fe738 upstream. "idx" is controled by the user and can be a negative offset into the input_names[] array. Signed-off-by:
-
Torstein Hegge authored
commit 61ac5130 upstream. UAC2_EXTENSION_UNIT_V2 differs from UAC1_EXTENSION_UNIT, but can be handled in the same way when parsing the unit. Otherwise parse_audio_unit() fails when it sees an extension unit on a UAC2 device. UAC2_EXTENSION_UNIT_V2 is outside the range allocated by UAC1. Signed-off-by:
Torstein Hegge <hegge@resisty.net> Acked-by:
Daniel Mack <zonque@gmail.com> Signed-off-by:
-
Eldad Zack authored
commit 5dae5fd2 upstream. Current code mishandles the case where the device is a UAC2 and the bDescriptorSubtype is a UAC2 Effect Unit (0x07). It tries to parse it as a Processing Unit (which is similar to two other UAC1 units with overlapping subtypes), but since the structure is different (See: 4.7.2.10, 4.7.2.11 in UAC2 standard), the parsing is done incorrectly and prevents the device from initializing. For now, just ignore the unit. Signed-off-by:
Eldad Zack <eldad@fogrefinery.com> Signed-off-by:
-
