The PCA chip for the NVMe LEDs is wired up backwards, so correct
the device tree labels.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add OCP debug card devicetree config
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

A recent change to the lm25066 driver changed the name of its
regulator from vout0 to vout; device-tree users of lm25066's regulator
functionality (of which ahe50dc is the only one) thus require a
corresponding update.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Due to the way i2c driver matching works (falling back to the driver's
id_table if of_match_table fails) this didn't actually cause any
misbehavior, but let's add the vendor prefixes so things actually work
the way they were intended to.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Like the more recently added ASRock BMC platforms, e3c246d4i and
romed8hm3 also have the BMC's MAC address available in the baseboard
FRU EEPROM, so let's add support for using it.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Added a device tree for IBM system1 BMC board, which uses AST2600 SoC.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-3-ninad@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document the new compatibles used on IBM system1-bmc
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Link: https://lore.kernel.org/r/20240125212154.4028640-2-ninad@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Enable FSI interrupt controllers for AST2600 and P10BMC hub master.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20240215220759.976998-27-eajames@linux.ibm.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add:
"reset-cause-platrst", "cpu0-err-alert", "leakage-detect-alert",
"presence-post-card", "ac-power-button", "P0_I3C_APML_ALERT_L",
"irq-uv-detect-alert", "irq-hsc-alert", "cpu0-prochot-alert",
"cpu0-thermtrip-alert", "reset-cause-pcie", "pvdd11-ocp-alert"

Rename:
"power-cpu-good" to "host0-ready",
"host-ready-n" to "post-end-n
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-13-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add pt5161l device in i2c bus12 and bus21.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-12-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Revise max31790 and delta_brick node name.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-11-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add ltc4286 device.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-10-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add MB NIC Device
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-9-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Revise max31790 address from 0x30 to 0x5e
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-8-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add PDB temperature sensor.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-7-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add spi-gpio for tpm device.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-6-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add a line name for cpu power good.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-5-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Remove vuart to avoid port conflict with uart2
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-4-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Change routing to match SOL(Serial Over LAN) settings.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-3-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

The same name as reset-control-smb-e1s
change to reset-control-smb-e1s-0 and reset-control-smb-e1s-0.
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20240412091600.2534693-2-peteryin.openbmc@gmail.comSigned-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add the SGPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-12-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add the GPIO line name that the project's function can use by the
meaningful name.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-11-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add led-fan-fault gpio pin on the PCA9555 on the i2c bus 0.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-10-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add fan rpm controller max31790 on all bus of FCB.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-9-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add bus labels and aliases for the fan control board.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-8-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Correct the address from 0x51 to 0x54 of eeprom on the i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-7-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add one temperature sensor on i2c bus 1
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-6-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Enable power monitor device ina230 and ltc2945 on the i2c bus 0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-5-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Correct the sgpio use from sgpiom1 to sgpiom0
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-4-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Remove the unuse setting and fix the link to 100 M
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-3-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

The project Minerva which is the platform used by Meta has two boards: the
Chassis Management Module (Minerva) and the Motherboard (Harma), so change
the DTS name to minerva here for CMM use.
Signed-off-by: Yang Chen <yangchen.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231212075200.983536-2-yangchen.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Add linux device tree entry related to
the Meta(Facebook) computer-node system use an AT2600 BMC.
This node is named "Harma".
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231211162656.2564267-3-peteryin.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document the new compatibles used on Meta Harma.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com>
Link: https://lore.kernel.org/r/20231211162656.2564267-2-peteryin.openbmc@gmail.comSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

This is a relatively low-cost AST2500-based Amd Ryzen 5000 Series
micro-ATX board that we hope can provide a decent platform for OpenBMC
development.

This initial device-tree provides the necessary configuration for
basic BMC functionality such as serial console, KVM support
and POST code snooping.
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231202003908.3635695-3-renze@rnplus.nlSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document Asrock X570D4U compatible.
Signed-off-by: Renze Nicolai <renze@rnplus.nl>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20231202003908.3635695-2-renze@rnplus.nlSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

This is a Xeon board broadly similar (aside from CPU vendor) to the
already-support romed8hm3 (half-width, single-socket, ast2500).  It
doesn't require anything terribly special for OpenBMC support, so this
device-tree should provide everything necessary for basic
functionality with it.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20231120121954.19926-6-zev@bewilderbeest.netSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Document ASRock SPC621D8HM3 board compatible.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231120121954.19926-5-zev@bewilderbeest.netSigned-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>

Pull EFI fixes from Ard Biesheuvel:

 - Fix logic that is supposed to prevent placement of the kernel image
   below LOAD_PHYSICAL_ADDR

 - Use the firmware stack in the EFI stub when running in mixed mode

 - Clear BSS only once when using mixed mode

 - Check efi.get_variable() function pointer for NULL before trying to
   call it

* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
  efi: fix panic in kdump kernel
  x86/efistub: Don't clear BSS twice in mixed mode
  x86/efistub: Call mixed mode boot services on the firmware's stack
  efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address

Pull x86 fixes from Thomas Gleixner:

 - Ensure that the encryption mask at boot is properly propagated on
   5-level page tables, otherwise the PGD entry is incorrectly set to
   non-encrypted, which causes system crashes during boot.

 - Undo the deferred 5-level page table setup as it cannot work with
   memory encryption enabled.

 - Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
   to the default value but the cached variable is not, so subsequent
   comparisons might yield the wrong result and as a consequence the
   result prevents updating the MSR.

 - Register the local APIC address only once in the MPPARSE enumeration
   to prevent triggering the related WARN_ONs() in the APIC and topology
   code.

 - Handle the case where no APIC is found gracefully by registering a
   fake APIC in the topology code. That makes all related topology
   functions work correctly and does not affect the actual APIC driver
   code at all.

 - Don't evaluate logical IDs during early boot as the local APIC IDs
   are not yet enumerated and the invoked function returns an error
   code. Nothing requires the logical IDs before the final CPUID
   enumeration takes place, which happens after the enumeration.

 - Cure the fallout of the per CPU rework on UP which misplaced the
   copying of boot_cpu_data to per CPU data so that the final update to
   boot_cpu_data got lost which caused inconsistent state and boot
   crashes.

 - Use copy_from_kernel_nofault() in the kprobes setup as there is no
   guarantee that the address can be safely accessed.

 - Reorder struct members in struct saved_context to work around another
   kmemleak false positive

 - Remove the buggy code which tries to update the E820 kexec table for
   setup_data as that is never passed to the kexec kernel.

 - Update the resource control documentation to use the proper units.

 - Fix a Kconfig warning observed with tinyconfig

* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot/64: Move 5-level paging global variable assignments back
  x86/boot/64: Apply encryption mask to 5-level pagetable update
  x86/cpu: Add model number for another Intel Arrow Lake mobile processor
  x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
  Documentation/x86: Document that resctrl bandwidth control units are MiB
  x86/mpparse: Register APIC address only once
  x86/topology: Handle the !APIC case gracefully
  x86/topology: Don't evaluate logical IDs during early boot
  x86/cpu: Ensure that CPU info updates are propagated on UP
  kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
  x86/pm: Work around false positive kmemleak report in msr_build_context()
  x86/kexec: Do not update E820 kexec table for setup_data
  x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'