Matching on interface numbers was not such a good idea
for multi-function serial devices after all. It is much
better do create well defined device layouts, allowing
a single match entry per device.

Remove this now unused code.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All the "non Gobi" Qualcomm based devices handled by this
driver share a common standard Sierra Wireless specific
layout. Adding code specifically for this layout allow
us to reduce the number of match entries per device from
three to one.

This change will result in a penalty wrt stable backports,
but simplifies new Sierra device addtitions in the long
term.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Preparing for more supported standard device layouts. Keeping
the matching macros unchanged to avoid breaking stable
backporting of new device additions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use a consistent style for all multiline comments.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add better error messages during the channel change/reservation establish
process.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the transition to the UWB_RSV_STATE_NONE state synchronous so that
there is not a race between uwb_rsv_terminate and uwb_rsv_establish.
uwb_rsv_terminate would set the rsv->state to UWB_RSV_STATE_NONE but did
not release the stream resource until a 320ms timeout had expired.  If a
user called uwb_rsv_establish during that time, it could fail to
establish the reservation because no stream resources were available.
This patch removes the timer from the uwb_rsv_terminate process since it
is not needed when transitioning to UWB_RSV_STATE_NONE.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using devm_ioremap_resource() API should actually be preferred over
devm_ioremap(), since the former request the mem region first and then
gives back the ioremap'ed memory pointer.
devm_ioremap_resource() calls request_mem_region(), therby preventing
other drivers to make any overlapping call to the same region.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the phy provider, supplied by new Exynos-usb2phy using
Generic phy framework.
Keeping the support for older USB phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ehci-exynos.
Once we move to new phy in the device nodes for ehci, we can
remove the support for older phys.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[gautam.vivek@samsung.com: Addressed review comments from mailing list]
[gautam.vivek@samsung.com: Kept the code for old usb-phy, and just
added support for new exynos5-usb2phy in generic phy framework]
[gautam.vivek@samsung.com: Edited the commit message]
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support to consume phy provided by Generic phy framework.
Keeping the support for older usb-phy intact right now, in order
to prevent any functionality break in absence of relevant
device tree side change for ohci-exynos.
Once we move to new phy in the device nodes for ohci, we can
remove the support for older phys.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change to use struct device instead of struct platform_device
for some static functions.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change to use struct device instead of struct platform_device
for some static functions.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Renesas R-Car USB PHY driver only supports the R8A7778 and
R8A7779, it isn't useful on other systems unless build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

My previous patch introduced a bug which prevented this driver from
loading.  devm_ioremap_resource() has a call to
devm_request_mem_region() which will fail because the address space is
shared between this PHY driver and CI device controller driver.

Fixes: 10f0577a ('usb: phy: msm: change devm_ioremap() to devm_ioremap_resource()')
Reported-by: "Ivan T. Ivanov" <iivanov@mm-sol.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update device states according to ch9 in USB 2.0 specification
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When tried to enable OTG FSM, we need to rebuild both kernel Image
and modules, since there are some codes at gadget modules which are
controlled by related configurations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 62bb84ed (usb: gadget: ci13xxx: convert to platform device)
start address of the capability registers is not passed correctly to
udc_probe(). Fix this.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allows controller to be specified via device tree.
Pass PHY phandle specified in DT to core driver.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document device tree binding information as required by
the Qualcomm USB controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The field PLLDIVVALUE of register PHY_CTRL_1 selects the reference clock source
for the PHY:
00 = sysclock uses 19.2 MHz
01 = sysclock uses 24 MHz
10 = sysclock uses 26 MHz
11 = sysclock uses 27 MHz

The reset value for this field is 10 according to the reference manual, and
even though this reset value works for mx53, it does not work for mx51.

So instead of relying on the reset value for the PLLDIVVALUE field, explicitly
set it to 01 so that a 24MHz clock can be selected for the PHY and allowing both
mx51 and mx53 to have USB OTG port functional.

Succesfully tested 'g_ether' on a imx51-babbage and on a imx53-qsb boards.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The otg queue work include operations: one is disable interrupt,
another one is call kernel queue work API. Many codes do this
operation, using one inline function to instead of them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Delete useless code
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update TODO list
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Felipe writes:

usb: patches for v3.16 merge window

Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.

Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>

Conflicts:
	drivers/usb/phy/phy-mv-u3d-usb.c

Use one timer to control command timeout.

start/kick the timer every time a command is completed and a
new command is waiting, or a new command is added to a empty list.

If the timer runs out, then tag the current command as "aborted", and
start the xhci command abortion process.

Previously each function that submitted a command had its own timer.
If that command timed out, a new command structure for the
command was created and it was put on a cancel_cmd_list list,
then a pci write to abort the command ring was issued.

when the ring was aborted, it checked if the current command
was the one to be canceled, later when the ring was stopped the
driver got ownership of the TRBs in the command ring,
compared then to the TRBs in the cancel_cmd_list,
and turned them into No-ops.

Now, instead, at timeout we tag the status of the command in the
command queue to be aborted, and start the ring abortion.
Ring abortion stops the command ring and gives control of the
commands to us.
All the aborted commands are now turned into No-ops.

If the ring is already stopped when the command times outs its not possible
to start the ring abortion, in this case the command is turnd to No-op
right away.

All these changes allows us to remove the entire cancel_cmd_list code.

The functions waiting for a command to finish no longer have their own timeouts.
They will wait either until the command completes normally,
or until the whole command abortion is done.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove the per-device command list and handle_cmd_in_cmd_wait_list()
and use the completion and status variables found in the
command structure in the global command list.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Create a list to store command structures, add a structure to it every time
a command is submitted, and remove it from the list once we get a
command completion event matching the command.

Callers that wait for completion will free their command structures themselves.
The other command structures are freed in the command completion event handler.

Also add a check that prevents queuing commands if host is dying
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

To create a global command queue we require that each command put on the
command ring is submitted with a command structure.

Functions that queue commands and wait for completion need to allocate a command
before submitting it, and free it once completed. The following command queuing
functions need to be modified.

xhci_configure_endpoint()
xhci_address_device()
xhci_queue_slot_control()
xhci_queue_stop_endpoint()
xhci_queue_new_dequeue_state()
xhci_queue_reset_ep()
xhci_configure_endpoint()

xhci_configure_endpoint() could already be called with a command structure,
and only xhci_check_maxpacket and xhci_check_bandwidth did not do so. These
are changed and a command structure is now required. This change also simplifies
the configure endpoint command completion handling and the "goto bandwidth_change"
handling code can be removed.

In some cases the command queuing function is called in interrupt context.
These commands needs to be allocated atomically, and they can't wait for
completion. These commands will in this patch be freed directly after queuing,
but freeing will be moved to the command completion event handler in a later
patch once we get the global command queue up.(Just so that we won't leak
memory in the middle of the patch set)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xHCI host controllers may only support a limited number of device slot
IDs, which is usually far less than the theoretical maximum number of
devices (255) that the USB specifications advertise.  This is
frustrating to consumers that expect to be able to plug in a large
number of devices.

Add a print statement when the Enable Slot command fails to show how
many devices the host supports.  We can't change hardware manufacturer's
design decisions, but hopefully we can save customers a little bit of
time trying to debug why their host mysteriously fails when too many
devices are plugged in.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Amund Hov <Amund.Hov@silabs.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using the IS_ENABLED() macro can make the code shorter and easier to read.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Save someone else the debug cycles of figuring out why a driver's
transfer request is failing or causing undefined system behavior.
Buffers submitted for dma must come from GFP allocated / DMA-able
memory.

Return -EAGAIN matching the return value for dma_mapping_error() cases.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fix wrong port number reported when trying to enable/disable
USB2.0 hardware LPM.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

for 3.16 merge window

Bunch of fixes and a new driver for Exynos5 USB 3.0 PHY.

We need these USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The value of the revision is stored in musb->tusb_revision,
so don't re-read it every time.
Exporting tusb_get_revision is not needed anymore,
so the dependency loop between tusb6010 and tusb6010_omap is resolved.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>