Check that the array indexes are in-bounds before accessing the rate2 and tmp
arrays.

Found with the following semantic patch:

<smpl>
@@
identifier t;
identifier idx;
expression E;
statement S;
@@
* for (... ; <+... t[idx] ...+> && idx < E ; ...)
S
</smpl>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix:

drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]

seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563)

Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.

Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.

arch/mips/bcm47xx/wgt634u.c calls gpio_to_irq() and got the correct irq
number with the old gpio handling code. With this patch the code in
wgt634u.c should work again. I do not have a wgt634u to test this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Instead of converting it to a bogus error code -1, we should
return the original error code from lower layer driver. This
error code will be printed so it may give user some clues on
what has happened.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While using STA mode in the AP firmware, avoid
calling some firmware commands which are not
supported by the AP firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Choose interface specific function calls
based on interface type instead of
firmware types.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add and delete self entry in the firmware sta database
for AP interface only. We do not need such an entry for
STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware supports hardware encryption feature
for the station interface running on AP
firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set mac type for station interface on AP firmware
as secondary. This allows the firmware to set specific
characteristics for the STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When user wants to add a station interface when
AP firmware is loaded & in-use, allow creating
it and also notify user about the same.

Allow adding max one STA interface for AP fw.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Specify the STA support in iface_limit and
in wihpy->interface_modes
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This avoids calling mwl8k_cmd_rf_antenna functions every
time mwl8k_config function is called.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Avoid calling mwl8k_cmd_set_rf_channel unconditionally
by checking IEEE80211_CONF_CHANGE_CHANNEL.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For the commands, that might change the hw characteristics
of the PHY device, stop the running bsses and resume them
once command is complete.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allow AP and Mesh mode to operate concurrently using
single radio. Verify this using fonera 2.0n featuring
RT3052 chipset and also TP-LINK TL-WN727N featuring
RT5370 chipset.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemal.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We use this macro only on 3 places - remove it and replace by other
appropriate macros for printing messages.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Those messages can flood in dmesg, so do not print them by default.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some messages provide useful information, but are disabled without
CONFIG_RT2X00_DEBUG=y, so enable them by default
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The sample data received through the spectral scan can be either in big or
little endian byteorder. This information isn't stored in the output file.
Therefore it is not possible for the analyzer software to find the correct byte
order.

It is relative common to get the data from a low end AP in big endian mode and
transfer it to another computer in little endian mode to analyze it. Therefore,
it would be better to store it in network (big endian) byte order.

The extension of the 8 bit bins for each bin to 16 bit is not necessary. This
operation can be done in userspace or on a different machine. Instead the
max_exp defining the amount of shifting required for each bin is exported to
userspace.

The change of the output format requires a change of the type in the sample
tlv to allow the userspace program to correctly detect the bin format.
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[siwu@hrz.tu-chemnitz.de: squashed patches, update commit message, rebase, fix endianess bug]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When using the spectral scan feature, frames with phy errors are
returned for further processing to the driver. However, if the frames
also have an invalid CRC (which seems to happen quite often), the frame
is marked with bad CRC and not with the PHY error bit. The FFT
processing function will thus miss the frames.

Fix this by changing the precedence in error marking.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Spectral packets are "bogus" packets and should not be further evaluated
by the RX path.

Statistics are added to keep track of these packets.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Export the various parameters to userspace.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes invalid access of RxBD ring buffer descriptor's
length and flag inside PCIe send_data_complete() routine. We are
supposed to modify TxBD buffer descriptor's length and flag here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Delete successive tests to the same location.  This looks like simple code
duplication.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@

*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
    when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
 { ... when forall
   return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Conflicts:
	drivers/net/wireless/ti/wlcore/main.c

Conflicts:
	drivers/net/wireless/ath/ath9k/main.c
	drivers/net/wireless/iwlwifi/dvm/tx.c

Before "mac80211: clean up mesh sta allocation warning"
was applied, mesh_sta_info_get() was reshuffled to please
sparse. As a result we neglect to initialize newly created
STAs. Fix this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.

An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.

Black- and whitelists are supported, but not simultaneously.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>