if "chip_id" is wrong or "dev->cfg.clock_out" is invalid, the i2c model is still loaded.
It will cause "kernel NULL pointer dereference" oops when the i2c model remove.
returning the err code will prevent the i2c model load.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBSky s950ci dvb-s/s2 ci PCIe card:
1>dvb frontend: M88TS2022(tuner),M88DS3103(demod)
2>ci controller: CIMAX SP2 or its clone.
3>PCIe bridge: CX23885

The patchs are based on the following patchs.
Olli Salonen submit:
https://patchwork.linuxtv.org/patch/26180/
https://patchwork.linuxtv.org/patch/26183/
https://patchwork.linuxtv.org/patch/26324/
Nibble Max submit:
https://patchwork.linuxtv.org/patch/26207/Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBSky s950ci dvb-s/s2 ci PCIe card:
1>dvb frontend: M88TS2022(tuner),M88DS3103(demod)
2>ci controller: CIMAX SP2 or its clone.
3>PCIe bridge: CX23885

The patchs are based on the following patchs.
Olli Salonen submit:
https://patchwork.linuxtv.org/patch/26180/
https://patchwork.linuxtv.org/patch/26183/
https://patchwork.linuxtv.org/patch/26324/
Nibble Max submit:
https://patchwork.linuxtv.org/patch/26207/Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

DVBSky s960ci dvb-s/s2 usb ci box:
1>dvb frontend: M88TS2022(tuner),M88DS3103(demod)
2>usb controller: CY7C86013A
3>ci controller: CIMAX SP2 or its clone.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Some new devices got added. Update cardlists.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Leadtek VC100 is a simple USB capture stick, similar to
Yakumo Movie Mixer.
Signed-off-by: Witold Krecicki <wpk+lkml@culm.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add an option to disable remote controller for DVBSky devices by specifying
the disable_rc option at modprobe.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

dev_err includes the function name in the log printout, so there is no need to include it manually. While here, fix a small grammatical error in the i2c error message.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The dvb-usb-v2 already prints out the MAC address, no need to print
it out also here.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use dev_err instead of pt1_printk
o reduce object code size
o remove now unused pt1_printk macro

Neaten dev_<level> uses in pt3
o add missing newlines
o align arguments
o remove unnecessary OOM messages as there's a generic one
o typo fixes in messages
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Toshiba TC90522 is wrongly categorized, fix it
Signed-off-by: ほち, AreMa Inc <knightrider@are.ma>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

lirc_imon.c and lirc_sasem.c contain an incoming_packet method that
is using deprecated printk's.  Removed blocks replacing with single
dev_info with a %*ph format instead.
Signed-off-by: Amber Thrall <amber.rose.thrall@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Now works with both NTSC and PAL. Tested with CC/XDS for NTSC and
teletext/WSS for PAL. The start lines were wrong, the WSS signal
wasn't captured and there was no difference between NTSC and PAL
w.r.t. the count[] values so NTSC returned way too many lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Move pci_disable_device() down otherwise it will complain about an
unfreed irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Don't mix UNSET and TUNER_ABSENT: you have to pick one or the other. For
this driver selecting UNSET to represent an absent tuner resulting in
the fewest changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Make sure that changing the standard or format is not allowed while
one or more of the video, vbi or mpeg vb2 queues are busy.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The vb2 framework knows if streaming is in progress, no need to use
a separate field for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The width, height and field values are core fields since both vbi, video
and blackbird use the same video input.

Move those fields to the correct struct.

Also fix the field checks in the try_fmt functions: add V4L2_FIELD_SEQ_BT/TB
support and map incorrect field values to a correct field value instead of
returning an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

There is no reason to dump the sram code to the kernel log when you
stop streaming. Remove those calls to cx88_sram_channel_dump.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The timeout is way too small. Especially complicated command like
CX2341X_ENC_STOP_CAPTURE takes much more time than 10 ms. Increase the
timeout to 1 second, just as ivtv does (the cx88-blackbird has the
same IP core for MPEG compression as ivtv).

This solves a nasty issue where STOP_CAPTURE would timeout and the
mailbox is left in a busy state, making it impossible to start streaming
a second time without reloading the driver first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

btcx-risc is for the bt8xx driver and other drivers shouldn't depend
on it. There is no benefit to use that module just to do a
pci_zalloc_consistent.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Remove this function. This makes all vb2 queues behave the same, which
simplifies comparing the various vb2 queue op implementations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Don't return -1, return a proper error.

Replace dprintk(0, ...) by pr_err since firmware load errors should just be
reported as an error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/pci/cx88/cx88-blackbird.c:476:25: warning: cast to restricted __le32
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and
video the changes are all over.

What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.

Much simpler and more robust.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The alsa driver uses videobuf low-level functions that are not
available in vb2, so replace them by driver-specific functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This list is only used if the width, height and/or format of a buffer has
changed, but that can never happen. Remove it and all associated code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a duplicate of dev->fmt and can be removed. As a consequence a
lot of tests that check if the format has changed midstream can be
removed as well: the format cannot change midstream, so this is a bogus
check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The only remaining place that modifies the relevant bit is in function
cx231xx_set_Colibri_For_LowIF
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The scanning itself just fails (as before this series) but now
the correct busses are scanned.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

All switching should be done by i2c mux adapters.
Drop explicit dont_use_port_3 flag.
Drop info message about switch.

Only the removed code in start_streaming is questionable:
It did switch the port_3 flag without accessing i2c in between.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and
I2C_1_MUX_3, letting the I2C core handling the switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

change almost all instances of I2C_1 to I2C_1_MUX_3

Only these cases are changed to I2C_1_MUX_1:
* All that have dont_use_port_3 set.
* CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3.
* eeprom access for 930C
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Get used i2c port from bus_nr and status of port_3 switch.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is used later for is_tuner function that switches i2c behaviour for
some tuners.

[mchehab@osg.samsung.com: Fix CodingStyle on a multi-line comment]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate
muxed i2c adapters.

Map mux adapters to I2C_1 for now.

Add local variables for i2c_adapters in dvb_init to get line lengths
shorter.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Replace numbers by the constants of same value and same meaning.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Change to I2C_0 ... I2C_2 for the master ports
and add I2C_1_MUX_1 and I2C_1_MUX_3 for the muxed ones.

V2: Renamed mux adapters to seperate them from master adapters.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of using the same name for all 3 i2c physical buses
inside cx231xx, name them differently, adding a number
to it. This helps to better deal with the logs.

[mchehab@osg.samsung.com: removed an unused bus_name var from
 the original patch]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

For each i2c master there is a i2c_client allocated that could be
deleted now that its only two users have been changed to use their
own i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>