- 27 Sep, 2022 1 commit
-
-
Junxiao Chang authored
This commit fixes DMA engine reset timeout issue in suspend/resume with ADLink I-Pi SMARC Plus board which dmesg shows: ... [ 54.678271] PM: suspend exit [ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL) [ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0 ... [ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7 [ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma [ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed [ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed ... The issue is related with serdes which impacts clock. There is serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to commit b9663b7c ("net: stmmac: Enable SERDES power up/down sequence") for detial. When issue is reproduced, DMA engine clock is not ready because serdes is not powered up. To reproduce DMA engine reset timeout issue with hardware which has serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click "Power Off/Log Out" -> "Suspend" menu, it disables network interface, then goes to sleep mode. When it wakes up, it enables network interface again. Stmmac driver is called in this way: 1. stmmac_release: Stop network interface. In this function, it disables DMA engine and network interface; 2. stmmac_suspend: It is called in kernel suspend flow. But because network interface has been disabled(netif_running(ndev) is false), it does nothing and returns directly; 3. System goes into S3 or S0ix state. Some time later, system is waken up by keyboard or mouse; 4. stmmac_resume: It does nothing because network interface has been disabled; 5. stmmac_open: It is called to enable network interace again. DMA engine is initialized in this API, but serdes is not power on so there will be DMA engine reset timeout issue. Similarly, serdes powerdown should be added in stmmac_release. Network interface might be disabled by cmd "ifconfig eth0 down", DMA engine, phy and mac have been disabled in ndo_stop callback, serdes should be powered down as well. It doesn't make sense that serdes is on while other components have been turned off. If ethernet interface is in enabled state(netif_running(ndev) is true) before suspend/resume, the issue couldn't be reproduced because serdes could be powered up in stmmac_resume. Because serdes_powerup is added in stmmac_open, it doesn't need to be called in probe function. Fixes: b9663b7c ("net: stmmac: Enable SERDES power up/down sequence") Signed-off-by:
Junxiao Chang <junxiao.chang@intel.com> Reviewed-by:
Voon Weifeng <weifeng.voon@intel.com> Tested-by:
Jimmy JS Chen <jimmyjs.chen@adlinktech.com> Tested-by:
Looi, Hong Aun <hong.aun.looi@intel.com> Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
- 26 Sep, 2022 6 commits
-
-
ruanjinjie authored
Add missing pci_disable_device() if rr_init_one() fails Signed-off-by:
ruanjinjie <ruanjinjie@huawei.com> Link: https://lore.kernel.org/r/20220923094320.3109154-1-ruanjinjie@huawei.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Peng Wu authored
The devm_ioremap() function returns NULL on error, it doesn't return error pointers. Fixes: 3a1a274e ("mlxbf_gige: compute MDIO period based on i1clk") Signed-off-by:
Peng Wu <wupeng58@huawei.com> Link: https://lore.kernel.org/r/20220923023640.116057-1-wupeng58@huawei.comSigned-off-by:
-
Rafael Mendonca authored
The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the 'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the 'uld_mutex' before returning. Additionally, since commit 5148e595 ("cxgb4: add EOTID tracking and software context dump"), the access to these ETHOFLD hardware queues should be protected by the 'mqprio_mutex' instead. Fixes: 2d0cb84d ("cxgb4: add ETHOFLD hardware queue support") Fixes: 5148e595 ("cxgb4: add EOTID tracking and software context dump") Signed-off-by:
Rafael Mendonca <rafaelmendsr@gmail.com> Reviewed-by:
Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.comSigned-off-by:
-
Hangyu Hua authored
nf_ct_put need to be called to put the refcount got by tcf_ct_fill_params to avoid possible refcount leak when tcf_ct_flow_table_get fails. Fixes: c34b961a ("net/sched: act_ct: Create nf flow table per zone") Signed-off-by:
Hangyu Hua <hbh25y@gmail.com> Link: https://lore.kernel.org/r/20220923020046.8021-1-hbh25y@gmail.comSigned-off-by:
-
Peilin Ye authored
Currently usbnet_disconnect() unanchors and frees all deferred URBs using usb_scuttle_anchored_urbs(), which does not free urb->context, causing a memory leak as reported by syzbot. Use a usb_get_from_anchor() while loop instead, similar to what we did in commit 19cfe912 ("Bluetooth: btusb: Fix memory leak in play_deferred"). Also free urb->sg. Reported-and-tested-by: syzbot+dcd3e13cf4472f2e0ba1@syzkaller.appspotmail.com Fixes: 69ee472f ("usbnet & cdc-ether: Autosuspend for online devices") Fixes: 638c5115 ("USBNET: support DMA SG") Signed-off-by:
Peilin Ye <peilin.ye@bytedance.com> Link: https://lore.kernel.org/r/20220923042551.2745-1-yepeilin.cs@gmail.comSigned-off-by:
-
Sasha Levin authored
This reverts commit fe2c9c61. On Tue, Sep 13, 2022 at 05:48:58PM +0100, Russell King (Oracle) wrote: >What happens if this is built as a module, and the module is loaded, >binds (and creates the directory), then is removed, and then re- >inserted? Nothing removes the old directory, so doesn't >debugfs_create_dir() fail, resulting in subsequent failure to add >any subsequent debugfs entries? > >I don't think this patch should be backported to stable trees until >this point is addressed. Revert until a proper fix is available as the original behavior was better. Cc: Marcin Wojtas <mw@semihalf.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: stable@kernel.org Reported-by:
Russell King <linux@armlinux.org.uk> Fixes: fe2c9c61 ("net: mvpp2: debugfs: fix memory leak when using debugfs_lookup()") Signed-off-by:
Sasha Levin <sashal@kernel.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20220923234736.657413-1-sashal@kernel.orgSigned-off-by:
-
- 24 Sep, 2022 1 commit
-
-
Andy Moreton authored
A previous patch added a wrapper function to take a lock around efx_mcdi_filter_table_remove(), but only changed EF10 VFs' method table to call it. Change it in the PF method table too. Fixes: 77eb4074 ("sfc: move table locking into filter_table_{probe,remove} methods") Signed-off-by:
Andy Moreton <andy.moreton@amd.com> Signed-off-by:
Edward Cree <ecree.xilinx@gmail.com> Link: https://lore.kernel.org/r/20220922211218.814-1-ecree@xilinx.comSigned-off-by:
-
- 23 Sep, 2022 6 commits
-
-
Jakub Kicinski authored
Alexander Couzens says: ==================== net: mt7531: pll & reset fixes ==================== Link: https://lore.kernel.org/r/20220917000734.520253-1-lynxis@fe80.euSigned-off-by:
-
Alexander Couzens authored
The datasheet [1] explicit describes it as requirement for a reset. [1] MT7531 Reference Manual for Development Board rev 1.0, page 735 Signed-off-by:
Alexander Couzens <lynxis@fe80.eu> Signed-off-by:
-
Alexander Couzens authored
Move the PLL init of the switch out of the pad configuration of the port 6 (usally cpu port). Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for outbound traffic on port 5 or port 6. Fixes: c288575f ("net: dsa: mt7530: Add the support of MT7531 switch") Cc: stable@vger.kernel.org Signed-off-by:
-
Lukas Bulwahn authored
Commit bbb774d9 ("net: Add tests for bonding and team address list management") adds the net team driver tests in the directory: tools/testing/selftests/drivers/net/team/ The file entry in MAINTAINERS for the TEAM DRIVER however refers to: tools/testing/selftests/net/team/ Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a broken file pattern. Repair this file entry in TEAM DRIVER. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Acked-by:
Benjamin Poirier <bpoirier@nvidia.com> Link: https://lore.kernel.org/r/20220922114053.10883-1-lukas.bulwahn@gmail.comSigned-off-by:
-
Radhey Shyam Pandey authored
When GEM is in SGMII mode and disabled as a wakeup source, the power management controller can power down the entire full power domain(FPD) if none of the FPD devices are in use. Incase of FPD off, there are below ethernet link up issues on non-wakeup suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the resume path which reinitializes PS GTR SGMII lanes. $ echo +20 > /sys/class/rtc/rtc0/wakealarm $ echo mem > /sys/power/state After resume: $ ifconfig eth0 up xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout phy phy-fd400000.phy.0: phy poweron failed --> -110 xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout SIOCSIFFLAGS: Connection timed out phy phy-fd400000.phy.0: phy poweron failed --> -110 Fixes: 8b73fa3a ("net: macb: Added ZynqMP-specific initialization") Signed-off-by:
Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Patrick Rohr authored
This change adds support for not enabling carrier during TUNSETIFF interface creation by specifying the IFF_NO_CARRIER flag. Our tests make heavy use of tun interfaces. In some scenarios, the test process creates the interface but another process brings it up after the interface is discovered via netlink notification. In that case, it is not possible to create a tun/tap interface with carrier off without it racing against the bring up. Immediately setting carrier off via TUNSETCARRIER is still too late. Signed-off-by:
Patrick Rohr <prohr@google.com> Cc: Maciej Żenczykowski <maze@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by:
Maciej Żenczykowski <maze@google.com> Acked-by:
Jason Wang <jasowang@redhat.com> Reviewed-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
- 22 Sep, 2022 20 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from Jakub Kicinski: "Including fixes from wifi, netfilter and can. A handful of awaited fixes here - revert of the FEC changes, bluetooth fix, fixes for iwlwifi spew. We added a warning in PHY/MDIO code which is triggering on a couple of platforms in a false-positive-ish way. If we can't iron that out over the week we'll drop it and re-add for 6.1. I've added a new "follow up fixes" section for fixes to fixes in 6.0-rcs but it may actually give the false impression that those are problematic or that more testing time would have caught them. So likely a one time thing. Follow up fixes: - nf_tables_addchain: fix nft_counters_enabled underflow - ebtables: fix memory leak when blob is malformed - nf_ct_ftp: fix deadlock when nat rewrite is needed Current release - regressions: - Revert "fec: Restart PPS after link state change" and the related "net: fec: Use a spinlock to guard `fep->ptp_clk_on`" - Bluetooth: fix HCIGETDEVINFO regression - wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2 - mptcp: fix fwd memory accounting on coalesce - rwlock removal fall out: - ipmr: always call ip{,6}_mr_forward() from RCU read-side critical section - ipv6: fix crash when IPv6 is administratively disabled - tcp: read multiple skbs in tcp_read_skb() - mdio_bus_phy_resume state warning fallout: - eth: ravb: fix PHY state warning splat during system resume - eth: sh_eth: fix PHY state warning splat during system resume Current release - new code bugs: - wifi: iwlwifi: don't spam logs with NSS>2 messages - eth: mtk_eth_soc: enable XDP support just for MT7986 SoC Previous releases - regressions: - bonding: fix NULL deref in bond_rr_gen_slave_id - wifi: iwlwifi: mark IWLMEI as broken Previous releases - always broken: - nf_conntrack helpers: - irc: tighten matching on DCC message - sip: fix ct_sip_walk_headers - osf: fix possible bogus match in nf_osf_find() - ipvlan: fix out-of-bound bugs caused by unset skb->mac_header - core: fix flow symmetric hash - bonding, team: unsync device addresses on ndo_stop - phy: micrel: fix shared interrupt on LAN8814" * tag 'net-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits) selftests: forwarding: add shebang for sch_red.sh bnxt: prevent skb UAF after handing over to PTP worker net: marvell: Fix refcounting bugs in prestera_port_sfp_bind() net: sched: fix possible refcount leak in tc_new_tfilter() net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD udp: Use WARN_ON_ONCE() in udp_read_skb() selftests: bonding: cause oops in bond_rr_gen_slave_id bonding: fix NULL deref in bond_rr_gen_slave_id net: phy: micrel: fix shared interrupt on LAN8814 net/smc: Stop the CLC flow if no link to map buffers on ice: Fix ice_xdp_xmit() when XDP TX queue number is not sufficient net: atlantic: fix potential memory leak in aq_ndev_close() can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported can: gs_usb: gs_can_open(): fix race dev->can.state condition can: flexcan: flexcan_mailbox_read() fix return value for drop = true net: sh_eth: Fix PHY state warning splat during system resume net: ravb: Fix PHY state warning splat during system resume netfilter: nf_ct_ftp: fix deadlock when nat rewrite is needed netfilter: ebtables: fix memory leak when blob is malformed netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain() ... -
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efiLinus Torvalds authored
Pull EFI fixes from Ard Biesheuvel: - Use the right variable to check for shim insecure mode - Wipe setup_data field when booting via EFI - Add missing error check to efibc driver * tag 'efi-urgent-for-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi: efi: libstub: check Shim mode using MokSBStateRT efi: x86: Wipe setup_data on pure EFI boot efi: efibc: Guard against allocation failure
-
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linuxLinus Torvalds authored
Pull gpio fixes from Bartosz Golaszewski: - fix a NULL-pointer dereference at driver unbind and a potential resource leak in error path in gpio-mockup - make the irqchip immutable in gpio-ftgpio010 - fix dereferencing a potentially uninitialized variable in gpio-tqmx86 - fix interrupt registering in gpiolib's character device code * tag 'gpio-fixes-for-v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully gpio: tqmx86: fix uninitialized variable girq gpio: ftgpio010: Make irqchip immutable gpio: mockup: Fix potential resource leakage when register a chip gpio: mockup: fix NULL pointer dereference when removing debugfs
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v6.0-2022-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull perf tools fixes from Arnaldo Carvalho de Melo: - Fix polling of system-wide events related to mixing per-cpu and per-thread events. - Do not check if /proc/modules is unchanged when copying /proc/kcore, that doesn't get in the way of post processing analysis. - Include program header in ELF files generated for JIT files, so that they can be opened by tools using elfutils libraries. - Enter namespaces when synthesizing build-ids. - Fix some bugs related to a recent cpu_map overhaul where we should be using an index and not the cpu number. - Fix BPF program ELF section name, using the naming expected by libbpf when using BPF counters in 'perf stat'. - Add a new test for perf stat cgroup BPF counter. - Adjust check on 'perf test wp' for older kernels, where the PERF_EVENT_IOC_MODIFY_ATTRIBUTES ioctl isn't supported. - Sync x86 cpufeatures with the kernel sources, no changes in tooling. * tag 'perf-tools-fixes-for-v6.0-2022-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: perf tools: Honor namespace when synthesizing build-ids tools headers cpufeatures: Sync with the kernel sources perf kcore_copy: Do not check /proc/modules is unchanged libperf evlist: Fix polling of system-wide events perf record: Fix cpu mask bit setting for mixed mmaps perf test: Skip wp modify test on old kernels perf jit: Include program header in ELF files perf test: Add a new test for perf stat cgroup BPF counter perf stat: Use evsel->core.cpus to iterate cpus in BPF cgroup counters perf stat: Fix cpu map index in bperf cgroup code perf stat: Fix BPF program section name
-
Hangbin Liu authored
RHEL/Fedora RPM build checks are stricter, and complain when executable files don't have a shebang line, e.g. *** WARNING: ./kselftests/net/forwarding/sch_red.sh is executable but has no shebang, removing executable bit Fix it by adding shebang line. Fixes: 6cf0291f ("selftests: forwarding: Add a RED test for SW datapath") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/20220922024453.437757-1-liuhangbin@gmail.comSigned-off-by:
-
Jakub Kicinski authored
When reading the timestamp is required bnxt_tx_int() hands over the ownership of the completed skb to the PTP worker. The skb should not be used afterwards, as the worker may run before the rest of our code and free the skb, leading to a use-after-free. Since dev_kfree_skb_any() accepts NULL make the loss of ownership more obvious and set skb to NULL. Fixes: 83bb623c ("bnxt_en: Transmit and retrieve packet timestamps") Reviewed-by:
Andy Gospodarek <gospo@broadcom.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20220921201005.335390-1-kuba@kernel.orgSigned-off-by:
-
Liang He authored
In prestera_port_sfp_bind(), there are two refcounting bugs: (1) we should call of_node_get() before of_find_node_by_name() as it will automaitcally decrease the refcount of 'from' argument; (2) we should call of_node_put() for the break of the iteration for_each_child_of_node() as it will automatically increase and decrease the 'child'. Fixes: 52323ef7 ("net: marvell: prestera: add phylink support") Signed-off-by:
Liang He <windhl@126.com> Reviewed-by:
Yevhen Orlov <yevhen.orlov@plvision.eu> Link: https://lore.kernel.org/r/20220921133245.4111672-1-windhl@126.comSigned-off-by:
-
Hangyu Hua authored
tfilter_put need to be called to put the refount got by tp->ops->get to avoid possible refcount leak when chain->tmplt_ops != NULL and chain->tmplt_ops != tp->ops. Fixes: 7d5509fa ("net: sched: extend proto ops with 'put' callback") Signed-off-by:
Vlad Buslov <vladbu@nvidia.com> Link: https://lore.kernel.org/r/20220921092734.31700-1-hbh25y@gmail.comSigned-off-by:
-
Sean Anderson authored
There is a separate receive path for small packets (under 256 bytes). Instead of allocating a new dma-capable skb to be used for the next packet, this path allocates a skb and copies the data into it (reusing the existing sbk for the next packet). There are two bytes of junk data at the beginning of every packet. I believe these are inserted in order to allow aligned DMA and IP headers. We skip over them using skb_reserve. Before copying over the data, we must use a barrier to ensure we see the whole packet. The current code only synchronizes len bytes, starting from the beginning of the packet, including the junk bytes. However, this leaves off the final two bytes in the packet. Synchronize the whole packet. To reproduce this problem, ping a HME with a payload size between 17 and 214 $ ping -s 17 <hme_address> which will complain rather loudly about the data mismatch. Small packets (below 60 bytes on the wire) do not have this issue. I suspect this is related to the padding added to increase the minimum packet size. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Sean Anderson <seanga2@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220920235018.1675956-1-seanga2@gmail.comSigned-off-by:
-
Peilin Ye authored
Prevent udp_read_skb() from flooding the syslog. Suggested-by:
Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by:
-
Jakub Kicinski authored
Jonathan Toppins says: ==================== bonding: fix NULL deref in bond_rr_gen_slave_id Fix a NULL dereference of the struct bonding.rr_tx_counter member because if a bond is initially created with an initial mode != zero (Round Robin) the memory required for the counter is never created and when the mode is changed there is never any attempt to verify the memory is allocated upon switching modes. ==================== Link: https://lore.kernel.org/r/cover.1663694476.git.jtoppins@redhat.comSigned-off-by:
-
Jonathan Toppins authored
This bonding selftest used to cause a kernel oops on aarch64 and should be architectures agnostic. Signed-off-by:
Jonathan Toppins <jtoppins@redhat.com> Acked-by:
Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by:
-
Jonathan Toppins authored
Fix a NULL dereference of the struct bonding.rr_tx_counter member because if a bond is initially created with an initial mode != zero (Round Robin) the memory required for the counter is never created and when the mode is changed there is never any attempt to verify the memory is allocated upon switching modes. This causes the following Oops on an aarch64 machine: [ 334.686773] Unable to handle kernel paging request at virtual address ffff2c91ac905000 [ 334.694703] Mem abort info: [ 334.697486] ESR = 0x0000000096000004 [ 334.701234] EC = 0x25: DABT (current EL), IL = 32 bits [ 334.706536] SET = 0, FnV = 0 [ 334.709579] EA = 0, S1PTW = 0 [ 334.712719] FSC = 0x04: level 0 translation fault [ 334.717586] Data abort info: [ 334.720454] ISV = 0, ISS = 0x00000004 [ 334.724288] CM = 0, WnR = 0 [ 334.727244] swapper pgtable: 4k pages, 48-bit VAs, pgdp=000008044d662000 [ 334.733944] [ffff2c91ac905000] pgd=0000000000000000, p4d=0000000000000000 [ 334.740734] Internal error: Oops: 96000004 [#1] SMP [ 334.745602] Modules linked in: bonding tls veth rfkill sunrpc arm_spe_pmu vfat fat acpi_ipmi ipmi_ssif ixgbe igb i40e mdio ipmi_devintf ipmi_msghandler arm_cmn arm_dsu_pmu cppc_cpufreq acpi_tad fuse zram crct10dif_ce ast ghash_ce sbsa_gwdt nvme drm_vram_helper drm_ttm_helper nvme_core ttm xgene_hwmon [ 334.772217] CPU: 7 PID: 2214 Comm: ping Not tainted 6.0.0-rc4-00133-g64ae13ed #4 [ 334.779950] Hardware name: GIGABYTE R272-P31-00/MP32-AR1-00, BIOS F18v (SCP: 1.08.20211002) 12/01/2021 [ 334.789244] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 334.796196] pc : bond_rr_gen_slave_id+0x40/0x124 [bonding] [ 334.801691] lr : bond_xmit_roundrobin_slave_get+0x38/0xdc [bonding] [ 334.807962] sp : ffff8000221733e0 [ 334.811265] x29: ffff8000221733e0 x28: ffffdbac8572d198 x27: ffff80002217357c [ 334.818392] x26: 000000000000002a x25: ffffdbacb33ee000 x24: ffff07ff980fa000 [ 334.825519] x23: ffffdbacb2e398ba x22: ffff07ff98102000 x21: ffff07ff981029c0 [ 334.832646] x20: 0000000000000001 x19: ffff07ff981029c0 x18: 0000000000000014 [ 334.839773] x17: 0000000000000000 x16: ffffdbacb1004364 x15: 0000aaaabe2f5a62 [ 334.846899] x14: ffff07ff8e55d968 x13: ffff07ff8e55db30 x12: 0000000000000000 [ 334.854026] x11: ffffdbacb21532e8 x10: 0000000000000001 x9 : ffffdbac857178ec [ 334.861153] x8 : ffff07ff9f6e5a28 x7 : 0000000000000000 x6 : 000000007c2b3742 [ 334.868279] x5 : ffff2c91ac905000 x4 : ffff2c91ac905000 x3 : ffff07ff9f554400 [ 334.875406] x2 : ffff2c91ac905000 x1 : 0000000000000001 x0 : ffff07ff981029c0 [ 334.882532] Call trace: [ 334.884967] bond_rr_gen_slave_id+0x40/0x124 [bonding] [ 334.890109] bond_xmit_roundrobin_slave_get+0x38/0xdc [bonding] [ 334.896033] __bond_start_xmit+0x128/0x3a0 [bonding] [ 334.901001] bond_start_xmit+0x54/0xb0 [bonding] [ 334.905622] dev_hard_start_xmit+0xb4/0x220 [ 334.909798] __dev_queue_xmit+0x1a0/0x720 [ 334.913799] arp_xmit+0x3c/0xbc [ 334.916932] arp_send_dst+0x98/0xd0 [ 334.920410] arp_solicit+0xe8/0x230 [ 334.923888] neigh_probe+0x60/0xb0 [ 334.927279] __neigh_event_send+0x3b0/0x470 [ 334.931453] neigh_resolve_output+0x70/0x90 [ 334.935626] ip_finish_output2+0x158/0x514 [ 334.939714] __ip_finish_output+0xac/0x1a4 [ 334.943800] ip_finish_output+0x40/0xfc [ 334.947626] ip_output+0xf8/0x1a4 [ 334.950931] ip_send_skb+0x5c/0x100 [ 334.954410] ip_push_pending_frames+0x3c/0x60 [ 334.958758] raw_sendmsg+0x458/0x6d0 [ 334.962325] inet_sendmsg+0x50/0x80 [ 334.965805] sock_sendmsg+0x60/0x6c [ 334.969286] __sys_sendto+0xc8/0x134 [ 334.972853] __arm64_sys_sendto+0x34/0x4c [ 334.976854] invoke_syscall+0x78/0x100 [ 334.980594] el0_svc_common.constprop.0+0x4c/0xf4 [ 334.985287] do_el0_svc+0x38/0x4c [ 334.988591] el0_svc+0x34/0x10c [ 334.991724] el0t_64_sync_handler+0x11c/0x150 [ 334.996072] el0t_64_sync+0x190/0x194 [ 334.999726] Code: b9001062 f9403c02 d53cd044 8b040042 (b8210040) [ 335.005810] ---[ end trace 0000000000000000 ]--- [ 335.010416] Kernel panic - not syncing: Oops: Fatal exception in interrupt [ 335.017279] SMP: stopping secondary CPUs [ 335.021374] Kernel Offset: 0x5baca8eb0000 from 0xffff800008000000 [ 335.027456] PHYS_OFFSET: 0x80000000 [ 335.030932] CPU features: 0x0000,0085c029,19805c82 [ 335.035713] Memory Limit: none [ 335.038756] Rebooting in 180 seconds.. The fix is to allocate the memory in bond_open() which is guaranteed to be called before any packets are processed. Fixes: 848ca918 ("net: bonding: Use per-cpu rr_tx_counter") CC: Jussi Maki <joamaki@gmail.com> Signed-off-by: -
Michael Walle authored
Since commit ece19502 ("net: phy: micrel: 1588 support for LAN8814 phy") the handler always returns IRQ_HANDLED, except in an error case. Before that commit, the interrupt status register was checked and if it was empty, IRQ_NONE was returned. Restore that behavior to play nice with the interrupt line being shared with others. Fixes: ece19502 ("net: phy: micrel: 1588 support for LAN8814 phy") Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by:
Divya Koppera <Divya.Koppera@microchip.com> Link: https://lore.kernel.org/r/20220920141619.808117-1-michael@walle.ccSigned-off-by:
-
Wen Gu authored
There might be a potential race between SMC-R buffer map and link group termination. smc_smcr_terminate_all() | smc_connect_rdma() -------------------------------------------------------------- | smc_conn_create() for links in smcibdev | schedule links down | | smc_buf_create() | \- smcr_buf_map_usable_links() | \- no usable links found, | (rmb->mr = NULL) | | smc_clc_send_confirm() | \- access conn->rmb_desc->mr[]->rkey | (panic) During reboot and IB device module remove, all links will be set down and no usable links remain in link groups. In such situation smcr_buf_map_usable_links() should return an error and stop the CLC flow accessing to uninitialized mr. Fixes: b9247544 ("net/smc: convert static link ID instances to support multiple links") Signed-off-by:Wen Gu <guwen@linux.alibaba.com> Link: https://lore.kernel.org/r/1663656189-32090-1-git-send-email-guwen@linux.alibaba.comSigned-off-by:
-
Ard Biesheuvel authored
We currently check the MokSBState variable to decide whether we should treat UEFI secure boot as being disabled, even if the firmware thinks otherwise. This is used by shim to indicate that it is not checking signatures on boot images. In the kernel, we use this to relax lockdown policies. However, in cases where shim is not even being used, we don't want this variable to interfere with lockdown, given that the variable may be non-volatile and therefore persist across a reboot. This means setting it once will persistently disable lockdown checks on a given system. So switch to the mirrored version of this variable, called MokSBStateRT, which is supposed to be volatile, and this is something we can check. Cc: <stable@vger.kernel.org> # v4.19+ Signed-off-by:
Ard Biesheuvel <ardb@kernel.org> Reviewed-by:
Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by:
Peter Jones <pjones@redhat.com>
-
Ard Biesheuvel authored
When booting the x86 kernel via EFI using the LoadImage/StartImage boot services [as opposed to the deprecated EFI handover protocol], the setup header is taken from the image directly, and given that EFI's LoadImage has no Linux/x86 specific knowledge regarding struct bootparams or struct setup_header, any absolute addresses in the setup header must originate from the file and not from a prior loading stage. Since we cannot generally predict where LoadImage() decides to load an image (*), such absolute addresses must be treated as suspect: even if a prior boot stage intended to make them point somewhere inside the [signed] image, there is no way to validate that, and if they point at an arbitrary location in memory, the setup_data nodes will not be covered by any signatures or TPM measurements either, and could be made to contain an arbitrary sequence of SETUP_xxx nodes, which could interfere quite badly with the early x86 boot sequence. (*) Note that, while LoadImage() does take a buffer/size tuple in addition to a device path, which can be used to provide the image contents directly, it will re-allocate such images, as the memory footprint of an image is generally larger than the PE/COFF file representation. Cc: <stable@vger.kernel.org> # v5.10+ Link: https://lore.kernel.org/all/20220904165321.1140894-1-Jason@zx2c4.com/Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-09-20 (ice) Michal re-sets TC configuration when changing number of queues. Mateusz moves the check and call for link-down-on-close to the specific path for downing/closing the interface. * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: ice: Fix interface being down after reset with link-down-on-close flag on ice: config netdev tc before setting queues number ==================== Link: https://lore.kernel.org/r/20220920205344.1860934-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Larysa Zaremba authored
The original patch added the static branch to handle the situation, when assigning an XDP TX queue to every CPU is not possible, so they have to be shared. However, in the XDP transmit handler ice_xdp_xmit(), an error was returned in such cases even before static condition was checked, thus making queue sharing still impossible. Fixes: 22bf877e ("ice: introduce XDP_TX fallback path") Signed-off-by:
Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by:
Alexander Lobakin <alexandr.lobakin@intel.com> Link: https://lore.kernel.org/r/20220919134346.25030-1-larysa.zaremba@intel.comSigned-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queueJakub Kicinski authored
Tony Nguyen says: ==================== Intel Wired LAN Driver Updates 2022-09-19 (iavf, i40e) Norbert adds checking of buffer size for Rx buffer checks in iavf. Michal corrects setting of max MTU in iavf to account for MTU data provided by PF, fixes i40e to set VF max MTU, and resolves lack of rate limiting when value was less than divisor for i40e. * '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue: i40e: Fix set max_tx_rate when it is lower than 1 Mbps i40e: Fix VF set max MTU size iavf: Fix set max MTU size with port VLAN and jumbo frames iavf: Fix bad page state ==================== Link: https://lore.kernel.org/r/20220919223428.572091-1-anthony.l.nguyen@intel.comSigned-off-by:
-
- 21 Sep, 2022 6 commits
-
-
Namhyung Kim authored
It needs to enter the namespace before reading a file. Fixes: 4183a8d7 ("perf tools: Allow synthesizing the build id for kernel/modules/tasks in PERF_RECORD_MMAP2") Signed-off-by:
Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220920222822.2171056-1-namhyung@kernel.orgSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com>
-
Arnaldo Carvalho de Melo authored
To pick the changes from: 7df54884 ("x86/bugs: Add "unknown" reporting for MMIO Stale Data") This only causes these perf files to be rebuilt: CC /tmp/build/perf/bench/mem-memcpy-x86-64-asm.o CC /tmp/build/perf/bench/mem-memset-x86-64-asm.o And addresses this perf build warning: Warning: Kernel ABI header at 'tools/arch/x86/include/asm/cpufeatures.h' differs from latest version at 'arch/x86/include/asm/cpufeatures.h' diff -u tools/arch/x86/include/asm/cpufeatures.h arch/x86/include/asm/cpufeatures.h Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Link: https://lore.kernel.org/lkml/YysTRji90sNn2p5f@kernel.orgSigned-off-by:
-
Adrian Hunter authored
/proc/kallsyms and /proc/modules are compared before and after the copy in order to ensure no changes during the copy. However /proc/modules also might change due to reference counts changing even though that does not make any difference. Any modules loaded or unloaded should be visible in changes to kallsyms, so it is not necessary to check /proc/modules also anyway. Remove the comparison checking that /proc/modules is unchanged. Fixes: fc1b691d ("perf buildid-cache: Add ability to add kcore to the cache") Reported-by:
Daniel Dao <dqminh@cloudflare.com> Signed-off-by:
Adrian Hunter <adrian.hunter@intel.com> Tested-by:
-
Adrian Hunter authored
Originally, (refer commit f90d194a ("perf evlist: Do not poll events that use the system_wide flag") there wasn't much reason to poll system-wide events because: 1. The mmaps get "merged" via set-output anyway (the per-cpu case) 2. perf reads all mmaps when any event is woken 3. system-wide mmaps do not fill up as fast as the mmaps for user selected events But there was 1 reason not to poll which was that it prevented correct termination due to POLLHUP on all user selected events. That issue is now easily resolved by using fdarray_flag__nonfilterable. With the advent of commit ae4f8ae1 ("libperf evlist: Allow mixing per-thread and per-cpu mmaps"), system-wide mmaps can be used also in the per-thread case where reason 1 does not apply. Fix the omission of system-wide events from polling by using the fdarray_flag__nonfilterable flag. Example: Before: $ perf record --no-bpf-event -vvv -e intel_pt// --per-thread uname 2>err.txt Linux $ grep 'sys_perf_event_open.*=\|pollfd' err.txt sys_perf_event_open: pid 155076 cpu -1 group_fd -1 flags 0x8 = 5 sys_perf_event_open: pid 155076 cpu -1 group_fd -1 flags 0x8 = 6 sys_perf_event_open: pid -1 cpu 0 group_fd -1 flags 0x8 = 7 sys_perf_event_open: pid -1 cpu 1 group_fd -1 flags 0x8 = 9 sys_perf_event_open: pid -1 cpu 2 group_fd -1 flags 0x8 = 10 sys_perf_event_open: pid -1 cpu 3 group_fd -1 flags 0x8 = 11 sys_perf_event_open: pid -1 cpu 4 group_fd -1 flags 0x8 = 12 sys_perf_event_open: pid -1 cpu 5 group_fd -1 flags 0x8 = 13 sys_perf_event_open: pid -1 cpu 6 group_fd -1 flags 0x8 = 14 sys_perf_event_open: pid -1 cpu 7 group_fd -1 flags 0x8 = 15 thread_data[0x55fb43c29e80]: pollfd[0] <- event_fd=5 thread_data[0x55fb43c29e80]: pollfd[1] <- event_fd=6 thread_data[0x55fb43c29e80]: pollfd[2] <- non_perf_event fd=4 After: $ perf record --no-bpf-event -vvv -e intel_pt// --per-thread uname 2>err.txt Linux $ grep 'sys_perf_event_open.*=\|pollfd' err.txt sys_perf_event_open: pid 156316 cpu -1 group_fd -1 flags 0x8 = 5 sys_perf_event_open: pid 156316 cpu -1 group_fd -1 flags 0x8 = 6 sys_perf_event_open: pid -1 cpu 0 group_fd -1 flags 0x8 = 7 sys_perf_event_open: pid -1 cpu 1 group_fd -1 flags 0x8 = 9 sys_perf_event_open: pid -1 cpu 2 group_fd -1 flags 0x8 = 10 sys_perf_event_open: pid -1 cpu 3 group_fd -1 flags 0x8 = 11 sys_perf_event_open: pid -1 cpu 4 group_fd -1 flags 0x8 = 12 sys_perf_event_open: pid -1 cpu 5 group_fd -1 flags 0x8 = 13 sys_perf_event_open: pid -1 cpu 6 group_fd -1 flags 0x8 = 14 sys_perf_event_open: pid -1 cpu 7 group_fd -1 flags 0x8 = 15 thread_data[0x55cc19e58e80]: pollfd[0] <- event_fd=5 thread_data[0x55cc19e58e80]: pollfd[1] <- event_fd=6 thread_data[0x55cc19e58e80]: pollfd[2] <- event_fd=7 thread_data[0x55cc19e58e80]: pollfd[3] <- event_fd=9 thread_data[0x55cc19e58e80]: pollfd[4] <- event_fd=10 thread_data[0x55cc19e58e80]: pollfd[5] <- event_fd=11 thread_data[0x55cc19e58e80]: pollfd[6] <- event_fd=12 thread_data[0x55cc19e58e80]: pollfd[7] <- event_fd=13 thread_data[0x55cc19e58e80]: pollfd[8] <- event_fd=14 thread_data[0x55cc19e58e80]: pollfd[9] <- event_fd=15 thread_data[0x55cc19e58e80]: pollfd[10] <- non_perf_event fd=4 Fixes: ae4f8ae1 ("libperf evlist: Allow mixing per-thread and per-cpu mmaps") Signed-off-by:
-
Adrian Hunter authored
With mixed per-thread and (system-wide) per-cpu maps, the "any cpu" value -1 must be skipped when setting CPU mask bits. Prior to commit cbd7bfc7 ("tools/perf: Fix out of bound access to cpu mask array") the invalid setting went unnoticed, but since then it causes perf record to fail with an error. Example: Before: $ perf record -e intel_pt// --per-thread uname Failed to initialize parallel data streaming masks After: $ perf record -e intel_pt// --per-thread uname Linux [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.068 MB perf.data ] Fixes: ae4f8ae1 ("libperf evlist: Allow mixing per-thread and per-cpu mmaps") Signed-off-by:
-
Namhyung Kim authored
It uses PERF_EVENT_IOC_MODIFY_ATTRIBUTES ioctl. The kernel would return ENOTTY if it's not supported. Update the skip reason in that case. Committer notes: On s/390 the args aren't used, so need to be marked __maybe_unused. Reviewed-by:
Ravi Bangoria <ravi.bangoria@amd.com> Signed-off-by:
-
