- 24 Jun, 2019 34 commits
-
-
Philipp Zabel authored
Add a sequence initialization work item to be run when OUTPUT buffers are queued in the initialization state. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Philipp Zabel authored
The sequence initialization already has to happen during the initialization phase, after headers have been queued on the OUTPUT queue. This means that sequence initialization has to be queued as a work item from QBUF on the OUTPUT queue. The internal framebuffer setup should be done later during VIDIOC_REQBUFS() on the CAPTURE queue. Signed-off-by:
-
Marco Felsch authored
When the DEC_CMD_STOP command is issued after the context has already consumed all the queued buffers, we need to make sure to wake the destination queue with last_buffer_dequeued set, to allow userspace to make progress in its EOS handling. As there might still be picture run workers pending at that point, we need to synchronize with them, so the sequence number comparison reads stable values. reword commit message] Signed-off-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Combine setting the last_buffer_dequeued flag on the capture video queue and waking up its done workqueue into a helper function. Signed-off-by:
-
Marco Felsch authored
coda_encoder_cmd() is racy, as the last scheduled picture run worker can still be in-flight while the ENC_CMD_STOP command is issued. Depending on the exact timing the sequence numbers might already be changed, but the last buffer might not have been put on the destination queue yet. In this case the current implementation would prematurely wake the destination queue with last_buffer_dequeued=true, causing userspace to call streamoff before the last buffer is handled. Close this race window by synchronizing with the pic_run_worker before doing the sequence check. Signed-off-by:
-
Philipp Zabel authored
Sequence number handling assumed that the BIT processor frame number starts counting at 1, but this is not true for the MPEG-2 decoder, which starts at 0. Fix the sequence counter offset detection to handle this. Signed-off-by:
-
Philipp Zabel authored
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour with other video codec drivers. Signed-off-by:
-
Michael Tretter authored
The CMD_START shall be used to start the processing after a drain that was initiated with CMD_STOP. Up until now, a drain on coda could only be finished with a STREAMOFF-STREAMON, which resulted in a reset of the device. Signed-off-by:
Michael Tretter <m.tretter@pengutronix.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
As warned by sparse: drivers/media/platform/marvell-ccic/cafe-driver.c:475:23: warning: symbol 'ov7670_info' was not declared. Should it be static? Signed-off-by: -
Aliasgar Surti authored
checkpatch reported "WARNING: line over 80 characters". This patch fixes the warning for file soc_camera/soc_ov5642.c Signed-off-by:
Aliasgar Surti <aliasgar.surti500@gmail.com> Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by:
-
Lubomir Rintel authored
It's impossible for mmpcam_calc_dphy() to be called without it. Signed-off-by:
Lubomir Rintel <lkundrak@v3.sk> Reviewed-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Lubomir Rintel authored
Avoid pointlessly calling calc_dphy() when the bus is not V4L2_MBUS_CSI2_DPHY. This will make it easier to replace the platform data with devicetree. Signed-off-by:
-
Hugues Fruchet authored
Add support of JPEG pixel format. This requires auto detection of data type from CSI-2 stream. Signed-off-by:
Hugues Fruchet <hugues.fruchet@st.com> Signed-off-by:
-
Hugues Fruchet authored
Add support of YUYV8 and UYVY8 pixel formats. Signed-off-by:
-
Hugues Fruchet authored
Add support of RGB565 pixel format. Signed-off-by:
-
Hugues Fruchet authored
Ask device connected on sink pad for link frequency in order to configure CLK_LANE_REG1 (ui_x4). If not available, ask for pixel rate information to compute it. This is needed to deal with compressed format such as JPEG where number of bits per pixel is unknown: computation of link frequency from pixel rate is not possible. Signed-off-by:
-
Lubomir Rintel authored
The sensor needs the MCLK clock running when it's being probed. On platforms where the sensor is instantiated from a DT (MMP2) it is going to happen asynchronously. Therefore, the current modus operandi, where the bridge driver fiddles with the sensor power and clock itself is not going to fly. As the comments wisely note, this doesn't even belong there. Luckily, the ov7670 driver is already able to control its power and reset lines, we can just drop the MMP platform glue altogether. It also requests the clock via the standard clock subsystem. Good -- let's set up a clock instance so that the sensor can ask us to enable the clock. Note that this is pretty dumb at the moment: the clock is hardwired to a particular frequency and parent. It was always the case. Signed-off-by:
-
Lubomir Rintel authored
An instance of a sensor on DT-based MMP2 platform is always going to be created asynchronously. Let's move the manual device creation away from the core to the Cafe driver (used on OLPC XO-1, not present in DT) and set up appropriate async matches: I2C on Cafe, FWNODE on MMP (OLPC XO-1.75). Signed-off-by:
-
Lubomir Rintel authored
The platform data is actually not used anywhere (along with the CSI support) and should be safe to remove. Signed-off-by:
Pavel Machek <pavel@ucw.cz> Signed-off-by:
-
Lubomir Rintel authored
Use the names more suitable for devicetree bindings. There are no board files utilizing this, thus we seem to be at liberty at renaming this without consequences. Signed-off-by:
-
Lubomir Rintel authored
The access to REG_CLKCTRL or REG_CTRL1 without the clock enabled hangs the machine. Enable the clock first. Signed-off-by:
-
Lubomir Rintel authored
Remove structure members and headers that are not actually used. Saves us from some noise in subsequent cleanup commits. Signed-off-by:
-
Lubomir Rintel authored
This accesses the clock registers directly and thus is going to stay in the way of making the driver devicetree friendly. No boards seems to actually use this. If it's somehow actually needed it needs to be done differently. This reverts commit 7c269f45. Signed-off-by:
-
Robert Jarzmik authored
In the patch refactoring the fw-node, the mt9m111 was broken for all platform_data based platforms, which were the first aim of this driver. Only the devicetree platform are still functional, probably because the testing was done on these. The result is that -EINVAL is systematically return for such platforms, what this patch fixes. [Sakari Ailus: Rework this to resolve a merge conflict and use dev_fwnode] Fixes: 98480d65 ("media: mt9m111: allow to setup pixclk polarity") Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by:
Simon Horman <horms+renesas@verge.net.au> Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Wolfram Sang authored
We have a dedicated pointer for that, so use it. Much easier to read and less computation involved. Signed-off-by:
-
Sakari Ailus authored
The mt9m111_power_on function did not properly clean up whenever it encountered an error. Do that now. Signed-off-by:
-
Sakari Ailus authored
The regulator_get() function returns a regulator when it succeeds. There's no need to check whether the regulator is NULL later on. Signed-off-by:
-
- 21 Jun, 2019 6 commits
-
-
Robert Jarzmik authored
In the soc_camera removal, the board specific power callback was dropped. This at least will remove the power optimization from ezx and em-x270 pxa based boards. As to recreate the same level of functionality, make the mt9m111 have a regulator providing it its power, so that board designers can plug in a gpio based or ldo regulator, mimicking their former soc_camera power hook. [sakari.ailus@linux.intel.com: fix a build warning] Fixes: 5c10113cc668 ("media: mt9m111: make a standalone v4l2 subdevice") Signed-off-by:Akinobu Mita <akinobu.mita@gmail.com> Tested-by:
-
Sakari Ailus authored
devm_gpiod_get never returns NULL; therefore it's not necessary to check for that. PTR_ERR(NULL) also yields zero, which is confusing to smatch. Reported-by:
-
Sakari Ailus authored
PTR_ERR(NULL) yields 0 which is commonly used to denote success. This is the case here, and PTR_ERR(NULL) is apparently shunned upon. Fix this by explicitly returning 0 if fwnode == NULL. Reported-by:
-
Janusz Krzysztofik authored
Commit c62b9605 ("media: ov6650: Register with asynchronous subdevice framework") carelessly requested creation of a video device node by setting a V4L2_SUBDEV_FL_HAS_DEVNODE flag. The driver is not ready for that as it doesn't implement proper locking required for serialization of IOCTLs. Fix it by dropping the flag assignment. Fixes: c62b9605 ("media: ov6650: Register with asynchronous subdevice framework") Signed-off-by:
Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by:
-
Shobhit Kukreti authored
Removed the warning from the following files: drivers/media/i2c/ov13858.c drivers/media/i2c/ov2685.c drivers/media/i2c/ov5695.c Signed-off-by:
Shobhit Kukreti <shobhitkukreti@gmail.com> Signed-off-by:
-
Johan Korsnes authored
Signed-off-by:
Johan Korsnes <johan.korsnes@gmail.com> Signed-off-by:
-
