Fix build error reported on armhf while preparing 6.1-rc5
for Debian.

iosm_ipc_protocol.c:244:36: error: passing argument 3 of
'dma_alloc_coherent' from incompatible pointer type.

Change phy_ap_shm type from phys_addr_t to dma_addr_t.

Fixes: faed4c6f ("net: iosm: shared memory protocol")
Reported-by: Bonaccorso Salvatore <carnil@debian.org>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparse warnings - iosm_ipc_mux_codec.c:1474 using plain
integer as NULL pointer.

Use skb_trim() to reset skb tail & len.

Fixes: 9413491e ("net: iosm: encode or decode datagram")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tim Harvey reports that link modes which he does not expect to be
supported are being advertised, and this is because of the workaround
we have for PHYs that switch interface modes.

Fix this up by checking whether rate matching will be used for the
requested interface mode, and if rate matching will be used, perform
validation only with the requested interface mode, rather than invoking
this workaround.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function nixge_hw_dma_bd_release() dereference of NULL pointer
priv->rx_bd_v is possible for the case of its allocation failure in
nixge_hw_dma_bd_init().

Move for() loop with priv->rx_bd_v dereference under the check for
its validity.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 492caffa ("net: ethernet: nixge: Add support for National Instruments XGE netdev")
Signed-off-by: Yuri Karpov <YKarpov@ispras.ru>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both p9_fd_create_tcp() and p9_fd_create_unix() will call
p9_socket_open(). If the creation of p9_trans_fd fails,
p9_fd_create_tcp() and p9_fd_create_unix() will return an
error directly instead of releasing the cscoket, which will
result in a socket leak.

This patch adds sock_release() to fix the leak issue.

Fixes: 6b18662e ("9p connect fixes")
Signed-off-by: Wang Hai <wanghai38@huawei.com>
ACKed-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ntb_netdev_init_module() returns the ntb_transport_register_client()
directly without checking its return value, if
ntb_transport_register_client() failed, the NTB client device is not
unregistered.

Fix by unregister NTB client device when ntb_transport_register_client()
failed.

Fixes: 548c237c ("net: Add support for NTB virtual ethernet device")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The am65_cpsw_nuss_cleanup_ndev() function calls unregister_netdev()
even if register_netdev() fails, which triggers WARN_ON(1) in
unregister_netdevice_many(). To fix it, make sure that
unregister_netdev() is called only on registered netdev.

Compile tested only.

Fixes: 84b4aa49 ("net: ethernet: ti: am65-cpsw: add multi port support in mac-only mode")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-fixes-2022-11-24
This series provides bug fixes to mlx5 driver.

Focusing on error handling and proper memory management in mlx5, in
general and in the newly added macsec module.

I still have few fixes left in my queue and I hope those will be the
last ones for mlx5 for this cycle.

Please pull and let me know if there is any problem.

Happy thanksgiving.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-11-23 (ixgbevf, i40e, fm10k, iavf, e100)

This series contains updates to various Intel drivers.

Shang XiaoJing fixes init module error path stop to resource leaks for
ixgbevf and i40e.

Yuan Can also does the same for fm10k and iavf.

Wang Hai stops freeing of skb as it was causing use after free error for
e100.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

I got a null-ptr-deref report as following when doing fault injection test:

BUG: kernel NULL pointer dereference, address: 0000000000000058
Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 1 PID: 253 Comm: 507-spi-dm9051 Tainted: G    B            N 6.1.0-rc3+
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
RIP: 0010:klist_put+0x2d/0xd0
Call Trace:
 <TASK>
 klist_remove+0xf1/0x1c0
 device_release_driver_internal+0x23e/0x2d0
 bus_remove_device+0x1bd/0x240
 device_del+0x357/0x770
 phy_device_remove+0x11/0x30
 mdiobus_unregister+0xa5/0x140
 release_nodes+0x6a/0xa0
 devres_release_all+0xf8/0x150
 device_unbind_cleanup+0x19/0xd0

//probe path:
phy_device_register()
  device_add()

phy_connect
  phy_attach_direct() //set device driver
    probe() //it's failed, driver is not bound
    device_bind_driver() // probe failed, it's not called

//remove path:
phy_device_remove()
  device_del()
    device_release_driver_internal()
      __device_release_driver() //dev->drv is not NULL
        klist_remove() <- knode_driver is not added yet, cause null-ptr-deref

In phy_attach_direct(), after setting the 'dev->driver', probe() fails,
device_bind_driver() is not called, so the knode_driver->n_klist is not
set, then it causes null-ptr-deref in __device_release_driver() while
deleting device. Fix this by setting dev->driver to NULL in the error
path in phy_attach_direct().

Fixes: e1393456 ("[PATCH] PHY Layer fixup")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the name_assign_type attribute was introduced (commit
685343fc, "net: add name_assign_type netdev attribute"), the
loopback device was explicitly mentioned as one which would make use
of NET_NAME_PREDICTABLE:

    The name_assign_type attribute gives hints where the interface name of a
    given net-device comes from. These values are currently defined:
...
      NET_NAME_PREDICTABLE:
        The ifname has been assigned by the kernel in a predictable way
        that is guaranteed to avoid reuse and always be the same for a
        given device. Examples include statically created devices like
        the loopback device [...]

Switch to that so that reading /sys/class/net/lo/name_assign_type
produces something sensible instead of returning -EINVAL.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when a FEC device is brought up, the irq coalesce settings
are reset to their default values (1000us, 200 frames). That's
unexpected, and breaks for example use of an appropriate .link file to
make systemd-udev apply the desired
settings (https://www.freedesktop.org/software/systemd/man/systemd.link.html),
or any other method that would do a one-time setup during early boot.

Refactor the code so that fec_restart() instead uses
fec_enet_itr_coal_set(), which simply applies the settings that are
stored in the private data, and initialize that private data with the
default values.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses pfc_alloc_status array overflow occurring for
send queue index value greater than PFC priority. Queue index can be
greater than supported PFC priority for multiple scenarios (e.g. QoS,
during non zero SMQ allocation for a PF/VF).
In those scenarios the API should return default tx scheduler '0'.
This is causing mbox errors as otx2_get_smq_idx returing invalid smq value.

Fixes: 99c969a8 ("octeontx2-pf: Add egress PFC support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, pause frame register GMAC_RX_FLOW_CTRL_RFE is not updated
correctly when 'ethtool -A <IFACE> autoneg off rx off tx off' command
is issued. This fix ensures the flow control change is reflected directly
in the GMAC_RX_FLOW_CTRL_RFE register.

Fixes: 46f69ded ("net: stmmac: Use resolved link config in mac_link_up()")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Goh, Wei Sheng <wei.sheng.goh@intel.com>
Signed-off-by: Noor Azura Ahmad Tarmizi <noor.azura.ahmad.tarmizi@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPV6 addresses are purged when setting the number of rx/tx
rings using ethtool -G. The function aq_set_ringparam
calls dev_close, which removes the addresses. As a solution,
call an internal function (aq_ndev_close).

Fixes: c1af5427 ("net: aquantia: Ethtool based ring size configuration")
Signed-off-by: Izabela Bakollari <ibakolla@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Defines prefixed with "CONFIG" should be limited to proper Kconfig options,
that are introduced in a Kconfig file.

Here, constants for bitmap indices of some configs are defined and these
defines begin with the config's name, and are suffixed with BITMAP_IDX.

To avoid defines prefixed with "CONFIG", name these constants
BITMAP_IDX_FOR_CONFIG_XYZ instead of CONFIG_XYZ_BITMAP_IDX.

No functional change.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The watchdog timer is used to monitor whether the process
of transmitting data is timeout. If we use qlcnic driver,
the dev_watchdog() that is the timer handler of watchdog
timer will call qlcnic_tx_timeout() to process the timeout.
But the qlcnic_tx_timeout() calls msleep(), as a result,
the sleep-in-atomic-context bugs will happen. The processes
are shown below:

   (atomic context)
dev_watchdog
  qlcnic_tx_timeout
    qlcnic_83xx_idc_request_reset
      qlcnic_83xx_lock_driver
        msleep

---------------------------

   (atomic context)
dev_watchdog
  qlcnic_tx_timeout
    qlcnic_83xx_idc_request_reset
      qlcnic_83xx_lock_driver
        qlcnic_83xx_recover_driver_lock
          msleep

Fix by changing msleep() to mdelay(), the mdelay() is
busy-waiting and the bugs could be mitigated.

Fixes: 629263ac ("qlcnic: 83xx CNA inter driver communication mechanism")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-6.1-20221124' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
linux-can-fixes-for-6.1-20221124

this is a pull request of 8 patches for net/master.

Ziyang Xuan contributes a patch for the can327, fixing a potential SKB
leak when the netdev is down.

Heiko Schocher's patch for the sja1000 driver fixes the width of the
definition of the OCR_MODE_MASK.

Zhang Changzhong contributes 4 patches. In the sja1000_isa, cc770, and
m_can_pci drivers the error path in the probe() function and in case
of the etas_es58x a function that is called by probe() are fixed.

Jiasheng Jiang add a missing check for the return value of the
devm_clk_get() in the m_can driver.

Yasushi SHOJI's patch for the mcba_usb fixes setting of the external
termination resistor.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.

From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.

Reverse the argument value of usb_msg.termination to fix this.

These are the two commands sequence, ON then OFF.

> No.     Time           Source                Destination           Protocol Length Info
>       1 0.000000       host                  1.3.1                 USB      46     URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No.     Time           Source                Destination           Protocol Length Info
>       2 4.372547       host                  1.3.1                 USB      46     URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9
Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Link: https://lore.kernel.org/all/20221124152504.125994-1-yashi@spacecubics.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Since the devm_clk_get may return error,
it should be better to add check for the cdev->hclk,
as same as cdev->cclk.

Fixes: f524f829 ("can: m_can: Create a m_can platform framework")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/all/20221123063651.26199-1-jiasheng@iscas.ac.cnSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In m_can_pci_remove() and error handling path of m_can_pci_probe(),
m_can_class_free_dev() should be called to free resource allocated by
m_can_class_allocate_dev(), otherwise there will be memleak.

Fixes: cab7ffc0 ("can: m_can: add PCI glue driver for Intel Elkhart Lake")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/all/1668168684-6390-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In case of register_candev() fails, clear
es58x_dev->netdev[channel_idx] and add free_candev(). Otherwise
es58x_free_netdevs() will unregister the netdev that has never been
registered.

Fixes: 85372578 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Arunachalam Santhanam <Arunachalam.Santhanam@in.bosch.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/1668413685-23354-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add the missing free_cc770dev() before return from cc770_isa_probe()
in the register_cc770dev() error handling case.

In addition, remove blanks before goto labels.

Fixes: 7e02e543 ("can: cc770: legacy CC770 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168557-6024-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add the missing free_sja1000dev() before return from
sja1000_isa_probe() in the register_sja1000dev() error handling case.

In addition, remove blanks before goto labels.

Fixes: 2a6ba39a ("can: sja1000: legacy SJA1000 ISA bus driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/all/1668168521-5540-1-git-send-email-zhangchangzhong@huawei.comSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

bitfield mode in ocr register has only 2 bits not 3, so correct
the OCR_MODE_MASK define.
Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/all/20221123071636.2407823-1-hs@denx.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

In can327_feed_frame_to_netdev(), it did not free the skb when netdev
is down, and all callers of can327_feed_frame_to_netdev() did not free
allocated skb too. That would trigger skb leak.

Fix it by adding kfree_skb() in can327_feed_frame_to_netdev() when netdev
is down. Not tested, just compiled.

Fixes: 43da2f07 ("can: can327: CAN/ldisc driver for ELM327 based OBD-II adapters")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/20221110061437.411525-1-william.xuanziyang@huawei.comReviewed-by: Max Staudt <max@enpas.org>
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The ACPI buffer memory (string.pointer) should be freed as the buffer is
not used after returning from bgx_acpi_match_id(), free it to prevent
memory leak.

Fixes: 46b903a0 ("net, thunder, bgx: Add support to get MAC address from ACPI.")
Signed-off-by: Yu Liao <liaoyu15@huawei.com>
Link: https://lore.kernel.org/r/20221123082237.1220521-1-liaoyu15@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

pci_get_device() will decrease the reference count for the *from*
parameter. So we don't need to call put_device() to decrease the
reference. Let's remove the put_device() in the loop and only decrease
the reference count of the returned 'pdev' for the last loop because it
will not be passed to pci_get_device() as input parameter. We don't need
to check if 'pdev' is NULL because it is already checked inside
pci_dev_put(). Also add pci_dev_put() for the error path.

Fixes: fe1939bb ("octeontx2-af: Add SDP interface support")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>
Link: https://lore.kernel.org/r/20221123065919.31499-1-wangxiongfeng2@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Call phylink_disconnect_phy() in tse_shutdown() to release the
resources occupied by phylink_of_phy_connect() in the tse_open().

Fixes: fef29982 ("net: altera: tse: convert to phylink")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221123011617.332302-1-liujian56@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When doing the following test steps, an error was found:
  step 1: modprobe virtio_net succeeded
    # modprobe virtio_net        <-- OK

  step 2: fault injection in register_netdevice()
    # modprobe -r virtio_net     <-- OK
    # ...
      FAULT_INJECTION: forcing a failure.
      name failslab, interval 1, probability 0, space 0, times 0
      CPU: 0 PID: 3521 Comm: modprobe
      Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
      Call Trace:
       <TASK>
       ...
       should_failslab+0xa/0x20
       ...
       dev_set_name+0xc0/0x100
       netdev_register_kobject+0xc2/0x340
       register_netdevice+0xbb9/0x1320
       virtnet_probe+0x1d72/0x2658 [virtio_net]
       ...
       </TASK>
      virtio_net: probe of virtio0 failed with error -22

  step 3: modprobe virtio_net failed
    # modprobe virtio_net        <-- failed
      virtio_net: probe of virtio0 failed with error -2

The root cause of the problem is that the queues are not
disable on the error handling path when register_netdevice()
fails in virtnet_probe(), resulting in an error "-ENOENT"
returned in the next modprobe call in setup_vq().

virtio_pci_modern_device uses virtqueues to send or
receive message, and "queue_enable" records whether the
queues are available. In vp_modern_find_vqs(), all queues
will be selected and activated, but once queues are enabled
there is no way to go back except reset.

Fix it by reset virtio device on error handling path. This
makes error handling follow the same order as normal device
cleanup in virtnet_remove() which does: unregister, destroy
failover, then reset. And that flow is better tested than
error handling so we can be reasonably sure it works well.

Fixes: 02465555 ("virtio_net: fix use after free on allocation failure")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20221122150046.3910638-1-lizetao1@huawei.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Currently offloading MACsec with authentication only (encrypt
property set to off) is not supported, block such requests
when adding/updating a macsec device.

Fixes: 8ff0ac5b ("net/mlx5: Add MACsec offload Tx command support")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently during update Tx security association (SA) flow, the Tx SA
active state is updated only if the Tx SA in question is the same SA
that the MACsec interface is using for Tx,in consequence when the
MACsec interface chose to work with this Tx SA later, where this SA
for example should have been updated to active state and it was not,
the relevant Tx SA HW context won't be installed, hence the MACSec
flow won't be offloaded.

Fix by update Tx SA active state as part of update flow regardless
whether the SA in question is the same Tx SA used by the MACsec
interface.

Fixes: 8ff0ac5b ("net/mlx5: Add MACsec offload Tx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently offload path limits replay window size to 32/64/128/256 bits,
such a limitation should not exist since software allows it.
Remove such limitation.

Fixes: eb43846b ("net/mlx5e: Support MACsec offload replay window")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently MACsec's add Rx SA flow steering (fs) rule routine
uses a spec object which is dynamically allocated and do
not free it upon leaving. The above led to a memory leak.

Fix by freeing dynamically allocated objects.

Fixes: 3b20949c ("net/mlx5e: Add MACsec RX steering rules")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fix update Rx SA wrong bail condition, naturally update functionality
needs to check that something changed otherwise bailout currently the
active state check does just the opposite, furthermore unlike deactivate
path which remove the macsec rules to deactivate the offload, the
activation path does not include the counter part installation of the
macsec rules.

Fix by using correct bailout condition and when Rx SA changes state to
active then add the relevant macsec rules.

While at it, refine function name to reflect more precisely its role.

Fixes: aae3454e ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The main functionality for this operation is to update the
active state of the Rx security channel (SC) if the new
active setting is different from the current active state
of this Rx SC, however the relevant active state check is
done post updating the current active state to match the
new active state, effectively blocks any offload state
update for the Rx SC in question.

Fix by delay the assignment to be post the relevant check.

Fixes: aae3454e ("net/mlx5e: Add MACsec offload Rx command support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

When the MACsec netdevice is deleted, all related Rx/Tx HW/SW
states should be released/deallocated, however currently part
of the Rx security channel association data is not cleaned
properly, hence the memory leaks.

Fix by make sure all related Rx Sc resources are cleaned/freed,
while at it improve code by grouping release SC context in a
function so it can be used in both delete MACsec device and
delete Rx SC operations.

Fixes: 5a39816a ("net/mlx5e: Add MACsec offload SecY support")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently the data path metadata flow id mask wrongly limits the
number of different RX security channels (SC) to 16, whereas in
adding RX SC the limit is "2^16 - 1" this cause an overlap in
metadata flow id once more than 16 RX SCs is added, this corrupts
MACsec RX offloaded flow handling.

Fix by using the correct mask, while at it improve code to use this
mask when adding the Rx rule and improve visibility of such errors
by adding debug massage.

Fixes: b7c9400c ("net/mlx5e: Implement MACsec Rx data path using MACsec skb_metadata_dst")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

'accel_tcp' is allocated by kvzalloc(), which should freed by kvfree().

Fixes: f52f2fae ("net/mlx5e: Introduce flow steering API")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

If kvzalloc() fails then return -ENOMEM.  Don't return success.

Fixes: 3b20949c ("net/mlx5e: Add MACsec RX steering rules")
Fixes: e467b283 ("net/mlx5e: Add MACsec TX steering rules")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>