Apparently JBL Quantum 600 has multiple hardware revisions. Apply
registration quirk to another device id as well.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210727093326.1153366-1-alexander@tsoy.meSigned-off-by: Takashi Iwai <tiwai@suse.de>

The issue on Acer SWIFT SF314-56 is that headset microphone doesn't work.
The following quirk fixed headset microphone issue. The fixup was found by trial and error.
Note that the fixup of SF314-54/55 (ALC256_FIXUP_ACER_HEADSET_MIC) was not successful on my SF314-56.
Signed-off-by: Nikos Liolios <liolios.nk@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210727030510.36292-1-liolios.nk@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&).  Otherwise it matches
wrongly with the other quirk types.

Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.

Fixes: 97991108 ("ALSA: usb-audio: Disable USB autosuspend properly in setup_disable_autosuspend()")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/s5hr1flh9ov.wl-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).

We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.

Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.

Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.

This earphone works fine on older kernel version load because
this is a newly-added behavior.

Fixes: d2e8f641 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The values of the line output controls can change when the SW/HW
switches are set to HW, and also when speaker switching is enabled.
These notifications were sent with a mask of only
SNDRV_CTL_EVENT_MASK_INFO. Change the notifications to set the
SNDRV_CTL_EVENT_MASK_VALUE mask bit as well.

When the mute control is updated, the notification was sent with a
mask of SNDRV_CTL_EVENT_MASK_INFO. Change the mask to the correct
value of SNDRV_CTL_EVENT_MASK_VALUE.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/8192e15ba62fa4bc90425c005f265c0de530be20.1626959758.git.g@b4.vuSigned-off-by: Takashi Iwai <tiwai@suse.de>

After the hardware mute button is pressed, private->vol_updated is set
so that the mute status is invalidated. As the channel mute values may
be affected by the global mute value, update scarlett2_mute_ctl_get()
to call scarlett2_update_volumes() if private->vol_updated is set.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/aa18ddbf8d8bd7f31832ab1b6b6057c00b931202.1626959758.git.g@b4.vuSigned-off-by: Takashi Iwai <tiwai@suse.de>

The Direct Monitor control for the 2i2 is an enumerated value, not a
boolean. Fix the control name to say "Playback Enum" instead of
"Playback Switch" in this case.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/faf5de1d2100038e7d07520d770fda4a1adc276a.1626959758.git.g@b4.vuSigned-off-by: Takashi Iwai <tiwai@suse.de>

Append "Playback Switch" to the names of "Mute" and "Dim" controls,
and append "Switch" to the "MSD Mode" control as per
Documentation/sound/designs/control-names.rst.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/77f1000652c37e3217fb8dad8e156bc6392abc0b.1626959758.git.g@b4.vuSigned-off-by: Takashi Iwai <tiwai@suse.de>

These devices has two interfaces, but only the second interface
contains the capture endpoint, thus quirk is required to delay the
registration until the second interface appears.
Tested-by: Jakub Fišer <jakub@ufiseru.cz>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721235605.53741-1-alexander@tsoy.meSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-fix-v5.14-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v5.14

A collection of fixes for ASoC that have come in since the merge window,
all driver specific.  There is a new core feature added for reversing
the order of operations when shutting down, this is needed to fix a bug
with the AMD Stonyridge platform, and we also tweak the Kconfig to make
the SSM2518 driver user selectable so it can be used with generic cards
but that requires no actual code changes.

On some Intel NUC10 variants, codec reports AC_JACK_PORT_NONE as
pin default config for all pins. This results in broken audio.
Add a quirk to force connectivity.

BugLink: https://github.com/clearlinux/distribution/issues/2396Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210720153216.2200938-1-kai.vehmanen@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The recent rewrite of the memory allocation helpers also changed the
page extraction to a common helper, snd_sgbuf_get_page().  But this
assumes implicitly that the buffer was allocated via the standard
helper (usually via preallocation), and didn't consider the case of
the manual buffer handling.

This patch fixes it and also covers the manual buffer management.

Fixes: 37af81c5 ("ALSA: core: Abstract memory alloc helpers")
Link: https://lore.kernel.org/r/20210720092732.12412-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

The hw_support_mmap() doesn't cover all memory allocation types and
might use a wrong device pointer for checking the capability.
Check the all memory allocation types more completely.

Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210720092640.12338-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

We missed the fact that ElkhartLake platforms have two different PCI
IDs. We only added one so the SOF driver is never selected by the
autodetection logic for the missing configuration.

BugLink: https://github.com/thesofproject/linux/issues/2990
Fixes: cc8f81c7 ('ALSA: hda: fix intel DSP config')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210719231746.557325-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

During probe the parent_clk_id is set to -1 which should not be used to
array index within hsdiv_rates[].
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-3-peter.ujfalusi@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

In case of an error within j721e_audio_startup() the domain->active must
be decremented to avoid unbalanced counter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210717122820.1467-2-peter.ujfalusi@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This is a Lenovo ThinkStation machine which uses the codec alc623.
There are 2 issues on this machine, the 1st one is the pop noise in
the lineout, the 2nd one is there are 2 Front Mics and pulseaudio
can't handle them, After applying the fixup of
ALC623_FIXUP_LENOVO_THINKSTATION_P340 to this machine, the 2 issues
are fixed.

Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20210719030231.6870-1-hui.wang@canonical.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

The BIOS on MSI Mortar B550m WiFi (MS-7C94) board with AMDGPU seems
disabling the other pins than HDMI although it has more outputs
including DP.

This patch adds the board to the allow list for enabling all pins.
Reported-by: Damjan Georgievski <gdamjan@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CAEk1YH4Jd0a8vfZxORVu7qg+Zsc-K+pR187ezNq8QhJBPW4gpw@mail.gmail.com
Link: https://lore.kernel.org/r/20210716135600.24176-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:

 In snd_sb_csp_stop():
     spin_lock_irqsave(&p->chip->mixer_lock, flags);
     spin_lock(&p->chip->reg_lock);

 In snd_sb_csp_load():
     spin_lock_irqsave(&p->chip->reg_lock, flags);
     spin_lock(&p->chip->mixer_lock);

Also the similar pattern is seen in snd_sb_csp_start().

Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.

This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7b0fcdaf-cd4f-4728-2eae-48c151a92e10@gmail.com
Link: https://lore.kernel.org/r/20210716132723.13216-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

While using the DMIC recording, the garbled data will be captured by the
DMIC. It is caused by the critical power of PLL closed in the jack detect
function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Link: https://lore.kernel.org/r/20210716085853.20170-1-oder_chiou@realtek.comSigned-off-by: Mark Brown <broonie@kernel.org>

For Stoneyridge platform, it is required to invoke DMA driver stop
first rather than invoking DWC I2S controller stop.

Enable dai_link structure stop_dma_fist flag to reverse the stop
sequence.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210716123015.15697-2-vijendar.mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

On stream stop, currently CPU DAI stop sequence invoked first
followed by DMA. For Few platforms, it is required to stop the
DMA first before stopping CPU DAI.

Introduced new flag in dai_link structure for reordering stop sequence.
Based on flag check, ASoC core will re-order the stop sequence.

Fixes: 4378f1fb ("ASoC: soc-pcm: Use different sequence for start/stop trigger")
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20210716123015.15697-1-vijendar.mukunda@amd.comSigned-off-by: Mark Brown <broonie@kernel.org>

SoundWire registers are only accessable after sdw components are succesfully
binded. Setup irqs at that point instead of doing at probe.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210716105735.6073-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

A property regex goes under 'patternProperties', not 'properties'
schema. Otherwise, the regex is interpretted as a fixed string.

Fixes: 17c2d247 ("ASoC: dt-bindings: renesas: rsnd: tidyup properties")
Cc: Mark Brown <broonie@kernel.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210715185952.1470138-1-robh@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Recently we've added a new usb_mixer element type, USB_MIXER_BESPOKEN,
but it wasn't added in the table in snd_usb_mixer_dump_cval().  This
is no big problem since each bespoken type should have its own dump
method, but it still isn't disallowed to use the standard one, so we
should cover it as well.  Along with it, define the table with the
explicit array initializer for avoiding other pitfalls.

Fixes: 785b6f29 ("ALSA: usb-audio: scarlett2: Fix wrong resume call")
Reported-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210714084836.1977-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>

currenlty wcd938x has only soundwire interface and depends on
symbols from wcd938x soundwire module, so make this dependency
explicit in Kconfig

Without this one of the randconfig endup setting
CONFIG_SND_SOC_WCD938X=y
CONFIG_SND_SOC_WCD938X_SDW=m
resulting in some undefined reference to wcd938x_sdw* symbols.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 04544222 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210713140417.23693-1-srinivas.kandagatla@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The ADL descriptor was missing an ACPI power setting, causing the DSP
to enter D3 even with a D0i1-compatible wake-on-voice/hotwording
capture stream.

Fixes: 4ad03f89 ('ASoC: SOF: Intel: Update ADL P to use its own descriptor')
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Sathya Prakash M R <sathya.prakash.m.r@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210712201620.44311-1-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>

The ALC5631 does not like multi-write accesses, avoid them. This fixes:

rt5631 4-001a: Unable to sync registers 0x3a-0x3c. -121

errors on resume from suspend (and all registers after the registers in
the error not being synced).

Inspired by commit 2d30e949 ("ASoC: rt5651: Fix regcache sync errors
on resume") from Hans de Geode, which fixed the same errors on ALC5651.
Signed-off-by: Maxim Schwalm <maxim.schwalm@gmail.com>
Link: https://lore.kernel.org/r/20210712005011.28536-1-digetx@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

If a 32-bit application is being used with a 64-bit kernel and is using
the mmap mechanism to write data, then the SNDRV_PCM_IOCTL_SYNC_PTR
ioctl results in calling snd_pcm_ioctl_sync_ptr_compat(). Make this use
pcm_lib_apply_appl_ptr() so that the substream's ack() method, if
defined, is called.

The snd_pcm_sync_ptr() function, used in the 64-bit ioctl case, already
uses snd_pcm_ioctl_sync_ptr_compat().

Fixes: 9027c463 ("ALSA: pcm: Call ack() whenever appl_ptr is updated")
Signed-off-by: Alan Young <consult.awy@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/c441f18c-eb2a-3bdd-299a-696ccca2de9c@gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>

Merge series "arm64: tegra: Enable audio IOMMU support on Tegra194" from Thierry Reding <thierry.reding@gmail.com>
Thierry Reding <treding@nvidia.com>:

From: Thierry Reding <treding@nvidia.com>

This small series addresses a minor issue with how IOMMU support is
wired up on various Tegra generations. Currently the virtual "card"
device is used to allocate DMA memory for, but since that device does
not actually exist, the path to memory cannot be correctly described.

To address this, this series moves to using the ADMAIF as the DMA device
for audio. This is a real device that can have a proper DMA mask set and
with which a stream ID can be associated with in the SMMU. The memory
accesses technically originate from the ADMA controller (that the ADMAIF
uses), but DMA channel are dynamically allocated at runtime while DMA
memory is allocated at driver load time, drivers won't have access to
the ADMA device yet.

Further patches will be required to correct this issue on Tegra186 and
Tegra210, but I wanted to get feedback on this approach first.

Changes in v2:
- add backwards-compatibility fallback

Thierry

Thierry Reding (2):
  ASoC: tegra: Use ADMAIF component for DMA allocations
  arm64: tegra: Enable audio IOMMU support on Tegra194

 arch/arm64/boot/dts/nvidia/tegra194.dtsi |  4 ++++
 sound/soc/tegra/tegra_pcm.c              | 30 ++++++++++++++----------
 2 files changed, 22 insertions(+), 12 deletions(-)

--
2.32.0

Currently the tlv320aic31xx driver has regulator support but does not
enable the regulators during probe, deferring this until something causes
ASoC to make the card active. It does put the device into cache only mode
but only when the component level probe is called, however if interrupts
are in use the driver will access the regmap before then which if the
regulators are not powered on would cause I/O problems.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210707160234.16253-1-broonie@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

None of the TAS2505 outputs are stereo, do not pretend they are by
implementing them using SOC*DOUBLE* macros referencing the same
register twice, use SOC*SINGLE* instead. Fix volume ranges and mute
control for the codec according to datasheet.

Fixes: b4525b61 ("ASoC: tlv320aic32x4: add support for TAS2505")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Claudius Heine <ch@denx.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210708091255.56502-1-marex@denx.deSigned-off-by: Mark Brown <broonie@kernel.org>

DMA memory is currently allocated for the soundcard device, which is a
virtual device added for the sole purpose of "stitching" together the
audio device. It is not a real device and therefore doesn't have a DMA
mask or a description of the path to and from memory of accesses.

Memory accesses really originate from the ADMA controller that provides
the DMA channels used by the PCM component. However, since the DMA
memory is allocated up-front and the DMA channels aren't known at that
point, there is no way of knowing the DMA channel provider at allocation
time.

The next best physical device in the memory path is the ADMAIF. Use it
as the device to allocate DMA memory to. iommus and interconnects device
tree properties can thus be added to the ADMAIF device tree node to
describe the memory access path for audio.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210708103432.1690385-2-thierry.reding@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

I know nothing about zone_device pages and !device_private pages; but if
try_to_migrate_one() will do nothing for them, then it's better that
try_to_migrate() filter them first, than trawl through all their vmas.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/lkml/1241d356-8ec9-f47b-a5ec-9b2bf66d242@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In the unlikely race case that page_mlock_one() finds VM_LOCKED has been
cleared by the time it got page table lock, page_vma_mapped_walk_done()
must be called before returning, either explicitly, or by a final call
to page_vma_mapped_walk() - otherwise the page table remains locked.

Fixes: cd62734c ("mm/rmap: split try_to_munlock from try_to_unmap")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Link: https://lore.kernel.org/lkml/20210711151446.GB4070@xsang-OptiPlex-9020/
Link: https://lore.kernel.org/lkml/f71f8523-cba7-3342-40a7-114abc5d1f51@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kernel recovers in due course from missing Mlocked pages: but there
was no point in calling page_mlock() (formerly known as
try_to_munlock()) on a THP, because nothing got done even when it was
found to be mapped in another VM_LOCKED vma.

It's true that we need to be careful: Mlocked accounting of pte-mapped
THPs is too difficult (so consistently avoided); but Mlocked accounting
of only-pmd-mapped THPs is supposed to work, even when multiple mappings
are mlocked and munlocked or munmapped.  Refine the tests.

There is already a VM_BUG_ON_PAGE(PageDoubleMap) in page_mlock(), so
page_mlock_one() does not even have to worry about that complication.

(I said the kernel recovers: but would page reclaim be likely to split
THP before rediscovering that it's VM_LOCKED? I've not followed that up)

Fixes: 9a73f61b ("thp, mlock: do not mlock PTE-mapped file huge pages")
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Link: https://lore.kernel.org/lkml/cfa154c-d595-406-eb7d-eb9df730f944@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Parallel developments in mm/rmap.c have left behind some out-of-date
comments: try_to_migrate_one() also accepts TTU_SYNC (already commented
in try_to_migrate() itself), and try_to_migrate() returns nothing at
all.

TTU_SPLIT_FREEZE has just been deleted, so reword the comment about it
in mm/huge_memory.c; and TTU_IGNORE_ACCESS was removed in 5.11, so
delete the "recently referenced" comment from try_to_unmap_one() (once
upon a time the comment was near the removed codeblock, but they drifted
apart).
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Reviewed-by: Alistair Popple <apopple@nvidia.com>
Link: https://lore.kernel.org/lkml/563ce5b2-7a44-5b4d-1dfd-59a0e65932a9@google.com/
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull irq fixes from Ingo Molnar:
 "Two fixes:

   - Fix a MIPS IRQ handling RCU bug

   - Remove a DocBook annotation for a parameter that doesn't exist
     anymore"

* tag 'irq-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/mips: Fix RCU violation when using irqdomain lookup on interrupt entry
  genirq/irqdesc: Drop excess kernel-doc entry @lookup

Pull scheduler fixes from Ingo Molnar:
 "Three fixes:

   - Fix load tracking bug/inconsistency

   - Fix a sporadic CFS bandwidth constraints enforcement bug

   - Fix a uclamp utilization tracking bug for newly woken tasks"

* tag 'sched-urgent-2021-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/uclamp: Ignore max aggregation if rq is idle
  sched/fair: Fix CFS bandwidth hrtimer expiry type
  sched/fair: Sync load_sum with load_avg after dequeue