Per SLIMbus specification, a reconfiguration sequence known as
'clock pause' needs to be broadcast over the bus while entering low-
power mode. Clock-pause is initiated by the controller driver.
To exit clock-pause, controller typically wakes up the framer device.
Since wakeup precedure is controller-specific, framework calls it via
controller's function pointer to invoke it.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SLIMbus devices use value-element, and information elements to
control device parameters (e.g. value element is used to represent
gain for codec, information element is used to represent interrupt
status for codec when codec interrupt fires).
Messaging APIs are used to set/get these value and information
elements. SLIMbus specification uses 8-bit "transaction IDs" for
messages where a read-value is anticipated. Framework uses a table
of pointers to store those TIDs and responds back to the caller in
O(1).
Caller can do synchronous and asynchronous reads/writes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support to parse slim devices from device tree.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support to slim controllers in the slim core,
including some utility functions invoked by the controller and
slim device drivers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.
SLIMbus uses Time-Division-Multiplexing to accommodate multiple data
channels, and control channel. Control channel has messages to do
device-enumeration, messages to send/receive control-data to/from
SLIMbus devices, messages for port/channel management, and messages to
do bandwidth allocation.
The framework supports multiple instances of the bus (1 controller per
bus), and multiple slave devices per controller.

This patch adds support to basic silmbus core which includes support to
SLIMbus type, slimbus device registeration and some basic data structures.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.

This patch adds device tree bindings for the slimbus.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SLIMbus (Serial Low Power Interchip Media Bus) is a specification
developed by MIPI (Mobile Industry Processor Interface) alliance.
SLIMbus is a 2-wire implementation, which is used to communicate with
peripheral components like audio-codec.

The summary of SLIMbus and API is documented in the 'summary' file.
Signed-off-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Maintenance is split between Gavin who works for Eckelmann and so has
the functional authority, knows the background and history of this bus
system and me who designed most of the actual code with the old
microcontroller code as reference.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This bus driver uses GPIOs to control the four SIOX bus lines.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Implement tracing for SIOX. There are events for the data that is
written to the bus and for data being read from it.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a clean-up patch, no functional changes intended.

It removes the unused parameter of type "struct ddcb_requ*" from
the functions genwqe_user_vmap() and genwqe_user_vunmap().
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a clean-up patch, no functional changes intended.

It makes all defines uppercase, following a "tradition"
that helps to make code clearer.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a clean-up patch, no functional changes intended.

It removes an unused variable from do_execute_ddcb() and
also renames the function free_user_pages(), prepending
"genwqe" prefix in order to clarify the code.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the necessary data for handling eFuse on the rk3328.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The eFuse size is defined in property <reg> before, but the length
of registers is not equal to the size on some platforms, so we
add a new property to redefine it.
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The efuse on UniPhier allows 8bit access according to the specification.
Since bit offset of nvmem is limited to 0-7, it is desiable to change
access unit of nvmem to 8bit.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Switch to more generic device_property_present to consider also non-DT
properties.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the caller doesn't set stride and/or word_size in struct nvmem_config
then nvmem_register accepts this but we may face strange effects later
due to both values being 0. Therefore use 1 as default for both values.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function binder_alloc_new_buf_locked() is only used in this file, so
make it static. Also clean up sparse warning:

drivers/android/binder_alloc.c:330:23: warning: no previous prototype
for ‘binder_alloc_new_buf_locked’ [-Wmissing-prototypes]

In addition, the line of the function name exceeds 80 characters when
add static for this function, hence indent its arguments anew.
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Trivial fix to spelling mistake in dev_dbg debug message. Also
add in a missing comma.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The CoreSight TPIU should be disabled when tracing to other sinks to allow
them to operate at full bandwidth.

This patch fixes tpiu_disable_hw() to correctly disable the TPIU by
configuring the TPIU to stop on flush, initiating a manual flush, waiting
for the flush to complete and then waits for the TPIU to indicate it has
stopped.
Signed-off-by: Robert Walker <robert.walker@arm.com>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix ptr_ret.cocci warnings:
drivers/hwtracing/coresight/coresight-tpiu.c:163:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-funnel.c:217:1-3: WARNING: PTR_ERR_OR_ZERO can be used
drivers/hwtracing/coresight/coresight-dynamic-replicator.c:166:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SIOX is a bus system invented at Eckelmann AG to control their building
management and refrigeration systems. Traditionally the bus was
implemented on custom microcontrollers, today Linux based machines are
in use, too.

The topology on a SIOX bus looks as follows:

      ,------->--DCLK-->---------------+----------------------.
      ^                                v                      v
 ,--------.                ,----------------------.       ,------
 |        |                |   ,--------------.   |       |
 |        |--->--DOUT-->---|->-|shift register|->-|--->---|
 |        |                |   `--------------'   |       |
 | master |                |        device        |       |  device
 |        |                |   ,--------------.   |       |
 |        |---<--DIN---<---|-<-|shift register|-<-|---<---|
 |        |                |   `--------------'   |       |
 `--------'                `----------------------'       `------
      v                                ^                      ^
      `----------DLD-------------------+----------------------'

There are two control lines (DCLK and DLD) driven from the bus master to
all devices in parallel and two daisy chained data lines, one for input
and one for output. DCLK is the clock to shift both chains by a single
bit. On an edge of DLD the devices latch both their input and output
shift registers.

This patch adds a framework for this bus type.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds a driver for the Virtual Box Guest PCI device used in
Virtual Box virtual machines. Enabling this driver will add support for
Virtual Box Guest integration features such as copy-and-paste, seamless
mode and OpenGL pass-through.

This driver also offers vboxguest IPC functionality which is needed
for the vboxfs driver which offers folder sharing support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commits adds a header describing the hardware interface for the
Virtual Box Guest PCI device used in Virtual Box virtual machines and
utility functions for talking to the Virtual Box hypervisor over this
interface.

These utility functions will used both by the vboxguest driver for the
PCI device which offers the /dev/vboxguest ioctl API and by the vboxfs
driver which offers folder sharing support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds the headers describing the ioctl API for the
/dev/vboxguest device used by the Virtual Box Guest Additions
in Virtual Box virtual machines.

The driver providing the /dev/vboxguest device will allow Virtual Box
Guest Additions features such as copy-and-paste, seamless mode and
OpenGL pass-through.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the macros should not use a trailing semicolon
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved the please, no space beofore tabs checkpatch
warning. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the Prefer 'unsigned int' to bare use of 'unsigned'
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the missing a blank line after declarations checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved open brace { should be on the previous line checkpatch
error. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the please, no space beofore tabs checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the missing a blank line after declarations checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver may sleep under a spinlock.
The function call path is:
tsi148_master_write \ tsi148_master_read (acquire the spinlock)
  vme_register_error_handler
    kmalloc(GFP_KERNEL) --> may sleep

To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.

This bug is found by my static analysis tool(DSAC) and checked by my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The label 'done' in function vop_ioctl is not used, so remove it. Fixes
build warning:

drivers/misc/mic/vop/vop_vringh.c:1001:1: warning: label 'done' defined but
not used [-Wunused-label]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Certain EEPROMS have a size that is larger than the number of address
bytes would allow, and store the MSB of the address in bit 3 of the
instruction byte.

This can be described in platform data using EE_INSTR_BIT3_IS_ADDR, or
in DT using the obsolete legacy "at25,addr-mode" property.
But currently there exists no non-deprecated way to describe this in DT.

Hence extend the existing "address-width" DT property to allow
specifying 9 address bits, and enable support for that in the driver.

This has been tested with a Microchip 25LC040A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Resolved all the Unnecessary space before function pointer arguments
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>