The Vaughan device support the 352800 rate and not
the 352000
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Plantronics Gamecom 780 headset has a firmware problem, and when the
FU 0x09 volume is changed, it results in either too loud or silence
except for a very narrow range.  This patch provides a workaround,
ignoring the node, initialize the volume in a sane value and keep
untouched.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65251Signed-off-by: Takashi Iwai <tiwai@suse.de>

In this case, there are two DACs, and DAC 0x03 is mono. In order
to make headphones and front speaker use DAC 0x02, and subwoofer use
DAC 0x03, we artificially cut the connection from nodes 0x14 and 0x15
to node 0x03, so they can only use DAC 0x02.

In addition, the 5460 and 5470 differs in the sense that 5470 also
needs a headset mic patch, whereas 5460 has individual detection for
headphone and headset mic.

BugLink: https://bugs.launchpad.net/bugs/1211920Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

CONFIG_ACPI dependent code should include <linux/acpi.h> instead of
directly including <acpi/acpi.h>.  This patch cleans up such wrong
inclusions for Thinkpad ACPI users.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a Kconfig of a codec driver doesn't match with the controller
(CONFIG_SND_HDA_INTEL), it'll result in the non-working automatic
probing.  Unfortunately kbuild can't give such a restriction, but at
least, it's possible to show a warning if such a condition is found.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Replace all with the standard EXPORT_SYMBOL_GPL().
Signed-off-by: Takashi Iwai <tiwai@suse.de>

So far, CONFIG_SND_HDA_CODEC_* kconfigs have been booleans due to
historical reasons.  The major reason was that the automatic codec
driver probing wouldn't work if user sets a codec driver as a module
while the controller driver as a built-in.  And, another reason was to
avoid exporting symbols of the helper codes when all drivers are built
in.

But, this sort of "kindness" rather confuses people in the end,
especially makes the config refinement via localmodconfig unhappy.
Also, a codec module would still work if you re-bind the controller
driver via sysfs (although it's no automatic loading), so there might
be a slight use case.

That said, better to let people fallen into a pitfall than being too
smart and restrict something.  Let's make things straightforward: now
all CONFIG_SND_HDA_CODEC_* become tristate, and all symbols exported
unconditionally.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'asoc-v3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Fixes for v3.13

The fixes here are all driver specific ones, none of which particularly
stand out but all of which are useful to users of those drivers.

Merge remote-tracking branches 'asoc/fix/adsp', 'asoc/fix/arizona', 'asoc/fix/atmel', 'asoc/fix/fsl', 'asoc/fix/kirkwood', 'asoc/fix/tegra', 'asoc/fix/wm8904' and 'asoc/fix/wm8962' into asoc-linus

This should help us avoid the following mutex deadlock:

[] mutex_lock+0x2a/0x50
[] hdmi_present_sense+0x53/0x3a0 [snd_hda_codec_hdmi]
[] generic_hdmi_resume+0x5a/0x70 [snd_hda_codec_hdmi]
[] hda_call_codec_resume+0xec/0x1d0 [snd_hda_codec]
[] snd_hda_power_save+0x1e4/0x280 [snd_hda_codec]
[] codec_exec_verb+0x5f/0x290 [snd_hda_codec]
[] snd_hda_codec_read+0x5b/0x90 [snd_hda_codec]
[] snd_hdmi_get_eld_size+0x1e/0x20 [snd_hda_codec_hdmi]
[] snd_hdmi_get_eld+0x2c/0xd0 [snd_hda_codec_hdmi]
[] hdmi_present_sense+0x9a/0x3a0 [snd_hda_codec_hdmi]
[] hdmi_repoll_eld+0x34/0x50 [snd_hda_codec_hdmi]
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

On the Dell machines with codec whose Subsystem Id is 0x10280640,
no external microphone can be detected when plugging a 3-ring headset.
Using ALC255_FIXUP_DELL1_MIC_NO_PRESENCE can fix this problem.

The codec (Vendor ID: 0x10ec0255) on the machine belongs to alc_269
family.

BugLink: https://bugs.launchpad.net/bugs/1260303
Cc: David Henningsson <david.henningsson@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When wm8904 work in DSP mode B, we still need to configure it to
work in DSP mode. Or else, it will work in Right Justified mode.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

Some devices are getting very close to the limit whilst polling the RAM
start, this patch adds a small delay to this loop to give a longer
startup timeout.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

When the process is sleeping at the SNDRV_PCM_STATE_PAUSED
state from the wait_for_avail function, the sleep process will be woken by
timeout(10 seconds). Even if the sleep process wake up by timeout, by this
patch, the process will continue with sleep and wait for the other state.
Signed-off-by: JongHo Kim <furmuwon@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch fixes the rates declared in the CPU DAI parameters:
- SNDRV_PCM_RATE_KNOT and the discrete rates SNDRV_PCM_RATE_xxx should
  not be used with SNDRV_PCM_RATE_CONTINUOUS,
- SNDRV_PCM_RATE_CONTINUOUS asks for rate_min and rate_max,
- the device may do streaming down to 5512Hz.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>

Reported-by: Kyung-Kwee Ryu <kyung-kwee.ryu@wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

The usage of SNDRV_RATES is not effective as we can have rates like 12000 or
some other ones used by decoders. This change the usage of this to use the raw
Hz values to be sent to kernel
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

For NUMA systems, initializing the blk-mq layer and using per node hctx.
We initialize submit queues to 1, while blk-mq nr_hw_queues is
initialized to the number of NUMA nodes.

This makes the null_init_hctx function overwrite memory outside of what
it allocated.  In my case it lead to writing garbage into struct
request_queue's mq_map.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since commit ec39f64b ("drm/radeon/dpm: Convert to use
devm_hwmon_register_with_groups") radeon_hwmon_init() is using
hwmon_device_register_with_groups(), which sets `rdev' as a device
private driver_data, while hwmon_attributes_visible() and
radeon_hwmon_show_temp_thresh() are still waiting for `drm_device'.

Fix them by using dev_get_drvdata(), in order to avoid this oops:

  BUG: unable to handle kernel paging request at 0000000000001e28
  IP: [<ffffffffa02ae8b4>] hwmon_attributes_visible+0x18/0x3d [radeon]
  PGD 15057e067 PUD 151a8e067 PMD 0
  Oops: 0000 [#1] PREEMPT SMP
  Call Trace:
    internal_create_group+0x114/0x1d9
    sysfs_create_group+0xe/0x10
    sysfs_create_groups+0x22/0x5f
    device_add+0x34f/0x501
    device_register+0x15/0x18
    hwmon_device_register_with_groups+0xb5/0xed
    radeon_hwmon_init+0x56/0x7c [radeon]
    radeon_pm_init+0x134/0x7e5 [radeon]
    radeon_modeset_init+0x75f/0x8ed [radeon]
    radeon_driver_load_kms+0xc6/0x187 [radeon]
    drm_dev_register+0xf9/0x1b4 [drm]
    drm_get_pci_dev+0x98/0x129 [drm]
    radeon_pci_probe+0xa3/0xac [radeon]
    pci_device_probe+0x6e/0xcf
    driver_probe_device+0x98/0x1c4
    __driver_attach+0x5c/0x7e
    bus_for_each_dev+0x7b/0x85
    driver_attach+0x19/0x1b
    bus_add_driver+0x104/0x1ce
    driver_register+0x89/0xc5
    __pci_register_driver+0x58/0x5b
    drm_pci_init+0x86/0xea [drm]
    radeon_init+0x97/0x1000 [radeon]
    do_one_initcall+0x7f/0x117
    load_module+0x1583/0x1bb4
    SyS_init_module+0xa0/0xaf
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
    figure out why it breaks things.

 2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
    was basically doing "x == x", from Dave Jones.

 3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
    Sebastian Siewior.

 4) Blackhole and prohibit routes in ipv6 were not doing the right thing
    because their ->input and ->output methods were not being assigned
    correctly.  Now they behave properly like their ipv4 counterparts.
    From Kamala R.

 5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
    really do not support this feature and will send garbage packets if
    fed fraglist SKBs.  From Eric Dumazet.

 6) Fix long standing user triggerable BUG_ON over loopback in RDS
    protocol stack, from Venkat Venkatsubra.

 7) Several not so common code paths can potentially try to invoke
    packet scheduler actions that might be NULL without checking.  Shore
    things up by either 1) defining a method as mandatory and erroring
    on registration if that method is NULL 2) defininig a method as
    optional and the registration function hooks up a default
    implementation when NULL is seen.  From Jamal Hadi Salim.

 8) Fix fragment detection in xen-natback driver, from Paul Durrant.

 9) Kill dangling enter_memory_pressure method in cg_proto ops, from
    Eric W Biederman.

10) SKBs that traverse namespaces should have their local_df cleared,
    from Hannes Frederic Sowa.

11) IOCB file position is not being updated by macvtap_aio_read() and
    tun_chr_aio_read().  From Zhi Yong Wu.

12) Don't free virtio_net netdev before releasing all of the NAPI
    instances.  From Andrey Vagin.

13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.

14) IPv6 routes that are no cached routes should not count against the
    garbage collection limits.  We had this almost right, but were
    missing handling addrconf generated routes properly.  From Hannes
    Frederic Sowa.

15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
    route info when they are called, from Stefan Tomanek.

16) TUN and MACVTAP have had truncated packet signalling for some time,
    fix from Jason Wang.

17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.

18) xen-netback does not interpret the NAPI budget properly for TX work,
    fix from Paul Durrant.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
  igb: Fix for issue where values could be too high for udelay function.
  i40e: fix null dereference
  xen-netback: fix gso_prefix check
  net: make neigh_priv_len in struct net_device 16bit instead of 8bit
  drivers: net: cpsw: fix for cpsw crash when build as modules
  xen-netback: napi: don't prematurely request a tx event
  xen-netback: napi: fix abuse of budget
  sch_tbf: use do_div() for 64-bit divide
  udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
  net:fec: remove duplicate lines in comment about errata ERR006358
  Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
  8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
  xen-netback: make sure skb linear area covers checksum field
  net: smc91x: Fix device tree based configuration so it's usable
  udp: ipv4: fix potential use after free in udp_v4_early_demux()
  macvtap: signal truncated packets
  tun: unbreak truncated packet signalling
  net: sched: htb: fix the calculation of quantum
  net: sched: tbf: fix the calculation of max_size
  micrel: add support for KSZ8041RNLI
  ...

Pull x86 fixes from Peter Anvin:
 "This is a pretty small batch:

  The biggest single change is to stop using EFI time services on 32-bit
  platforms.  This matches our current behavior on 64-bit platforms as
  we already had ruled them out there as being too unreliable.  Turns
  out that affects 32-bit platforms, too.

  One NULL pointer fix for SGI UV.

  Two minor build fixes, one of which only affects icc and the other
  which affects icc and future versions or nonstandard default settings
  of gcc"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, efi: Don't use (U)EFI time services on 32 bit
  x86, build, icc: Remove uninitialized_var() from compiler-intel.h
  x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
  x86, build: Pass in additional -mno-mmx, -mno-sse options

Pull PCI updates from Bjorn Helgaas:
 "PCI device hotplug
    - Move device_del() from pci_stop_dev() to pci_destroy_dev() (Rafael
      Wysocki)

  Host bridge drivers
    - Update maintainers for DesignWare, i.MX6, Armada, R-Car (Bjorn
      Helgaas)
    - mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
      (Jason Gunthorpe)

  Miscellaneous
    - Avoid unnecessary CPU switch when calling .probe() (Alexander
      Duyck)
    - Revert "workqueue: allow work_on_cpu() to be called recursively"
      (Bjorn Helgaas)
    - Disable Bus Master only on kexec reboot (Khalid Aziz)
    - Omit PCI ID macro strings to shorten quirk names for LTO (Michal
      Marek)"

* tag 'pci-v3.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Add DesignWare, i.MX6, Armada, R-Car PCI host maintainers
  PCI: Disable Bus Master only on kexec reboot
  PCI: mvebu: Return 'unsupported' for Interrupt Line and Interrupt Pin
  PCI: Omit PCI ID macro strings to shorten quirk names
  PCI: Move device_del() from pci_stop_dev() to pci_destroy_dev()
  Revert "workqueue: allow work_on_cpu() to be called recursively"
  PCI: Avoid unnecessary CPU switch when calling driver .probe() method

Pull SELinux fixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: process labeled IPsec TCP SYN-ACK packets properly in selinux_ip_postroute()
  selinux: look for IPsec labels on both inbound and outbound packets
  selinux: handle TCP SYN-ACK packets correctly in selinux_ip_postroute()
  selinux: handle TCP SYN-ACK packets correctly in selinux_ip_output()
  selinux: fix possible memory leak

This reverts commit 102aefdd.

Tom London reports that it causes sync() to hang on Fedora rawhide:

  https://bugzilla.redhat.com/show_bug.cgi?id=1033965

and Josh Boyer bisected it down to this commit.  Reverting the commit in
the rawhide kernel fixes the problem.

Eric Paris root-caused it to incorrect subtype matching in that commit
breaking fuse, and has a tentative patch, but by now we're better off
retrying this in 3.14 rather than playing with it any more.
Reported-by: Tom London <selinux@gmail.com>
Bisected-by: Josh Boyer <jwboyer@fedoraproject.org>
Acked-by: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Anand Avati <avati@redhat.com>
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch changes the igb_phy_has_link function to check the value of the
parameter before deciding to use udelay or mdelay in order to be sure that
the value is not too high for udelay function.

CC: stable kernel <stable@vger.kernel.org> # 3.9+
Signed-off-by: Sunil K Pandey <sunil.k.pandey@intel.com>
Signed-off-by: Kevin B Smith <kevin.b.smith@intel.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the vsi->tx_rings structure is NULL we don't want to panic.

Change-Id: Ic694f043701738c434e8ebe0caf0673f4410dc10
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull EDAC fix from Borislav Petkov:
 "Silence a compiler warning in sb_edac"

* tag 'edac_fixes_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  sb_edac: Shut up compiler warning when EDAC_DEBUG is enabled

Pull ARM fixes from Russell King:
 "This resolves some further issues with the dma mask changes on ARM
  which have been found by TI and others, and also some corner cases
  with the updates to the virtual to physical address translations.

  Konstantin also found some problems with the unwinder, which now
  performs tighter verification that the stack is valid while unwinding"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: fix asm/memory.h build error
  ARM: 7917/1: cacheflush: correctly limit range of memory region being flushed
  ARM: 7913/1: fix framepointer check in unwind_frame
  ARM: 7912/1: check stack pointer in get_wchan
  ARM: 7909/1: mm: Call setup_dma_zone() post early_paging_init()
  ARM: 7908/1: mm: Fix the arm_dma_limit calculation
  ARM: another fix for the DMA mapping checks

Pull ARC fixes from Vineet Gupta:
 "These are couple of weeks old already, but I just couldn't get them to
  you earlier.

   - couple of fixes for recently added perf code
   - build time extable sort"

* tag 'arc-fixes-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: [perf] Fix a few thinkos
  ARC: Add guard macro to uapi/asm/unistd.h
  ARC: extable: Enable sorting at build time

Pull device mapper fixes from Mike Snitzer:
 "A set of device-mapper fixes for 3.13.

  A fix for possible memory corruption during DM table load, fix a
  possible leak of snapshot space in case of a crash, fix a possible
  deadlock due to a shared workqueue in the delay target, fix to
  initialize read-only module parameters that are used to export metrics
  for dm stats and dm bufio.

  Quite a few stable fixes were identified for both the thin-
  provisioning and caching targets as a result of increased regression
  testing using the device-mapper-test-suite (dmts).  The most notable
  of these are the reference counting fixes for the space map btree that
  is used by the dm-array interface -- without these the dm-cache
  metadata will leak, resulting in dm-cache devices running out of
  metadata blocks.  Also, some important fixes related to the
  thin-provisioning target's transition to read-only mode on error"

* tag 'dm-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm array: fix a reference counting bug in shadow_ablock
  dm space map: disallow decrementing a reference count below zero
  dm stats: initialize read-only module parameter
  dm bufio: initialize read-only module parameters
  dm cache: actually resize cache
  dm cache: update Documentation for invalidate_cblocks's range syntax
  dm cache policy mq: fix promotions to occur as expected
  dm thin: allow pool in read-only mode to transition to read-write mode
  dm thin: re-establish read-only state when switching to fail mode
  dm thin: always fallback the pool mode if commit fails
  dm thin: switch to read-only mode if metadata space is exhausted
  dm thin: switch to read only mode if a mapping insert fails
  dm space map metadata: return on failure in sm_metadata_new_block
  dm table: fail dm_table_create on dm_round_up overflow
  dm snapshot: avoid snapshot space leak on crash
  dm delay: fix a possible deadlock due to shared workqueue

Pull HID fixes from Jiri Kosina:

 - Genius Gx Imperator Keyboard regression fix (missing break in case),
   by Ben Hutchings

 - duplicate sysfs entry error fix for hid-sensor-hub driver, by
   Srinivas Pandruvada

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hid-sensor-hub: fix duplicate sysfs entry error
  HID: kye: Fix missing break in kye_report_fixup()

Jason Gunthorpe reports a build failure when ARM_PATCH_PHYS_VIRT is
not defined:

In file included from arch/arm/include/asm/page.h:163:0,
                 from include/linux/mm_types.h:16,
                 from include/linux/sched.h:24,
                 from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function '__virt_to_phys':
arch/arm/include/asm/memory.h:244:40: error: 'PHYS_OFFSET' undeclared (first use in this function)
arch/arm/include/asm/memory.h:244:40: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/include/asm/memory.h: In function '__phys_to_virt':
arch/arm/include/asm/memory.h:249:13: error: 'PHYS_OFFSET' undeclared (first use in this function)

Fixes: ca5a45c0 ("ARM: mm: use phys_addr_t appropriately in p2v and v2p conversions")
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Pull regulator fixes from Mark Brown:
 "A small set of driver fixes plus one larger core change which changes
  the way we check to see if we're using DT so that there aren't any
  races between deciding we're using DT and the regulator subsystem
  noticing.

  This makes the new support for substituting a dummy regulator and
  optional regulators work a lot better on DT systems since it ensures
  that we don't trigger probe deferral when we shouldn't which was
  causing bugs in clients"

* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: pfuze100: allow misprogrammed ID
  regulator: pfuze100: Fix address of FABID
  regulator: as3722: set the correct current limit
  regulator: core: Check for DT every time we check full constraints
  regulator: core: Replace checks of have_full_constraints with a function

Pull regmap fixes from Mark Brown:
 "Two small changes to fix some error handling and checking (both of
  which would be quite serious if the errors trigger) plus a trivial
  documentation fix"

* tag 'regmap-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: use IS_ERR() to check clk_get() results
  regmap: make sure we unlock on failure in regmap_bulk_write
  regmap: trivial comment fix (copy'n'paste error)

Pull i2c fixes from Wolfram Sang:
 "Here are two simple but wanted fixes for the i2c subsystem"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: Check the return value from clk_prepare_enable()
  i2c: mux: Inherit retry count and timeout from parent for muxed bus