Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next

Jonathan writes:

1st set of IIO new device support, features and cleanup for 6.1

This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.

New device support
- liteon,ltrf216a
  * New driver and dt bindings to support this Light sensor.
- maxim,max11205
  * New driver for this 16bit single channel ADC.
- memsensing,msa311
  * New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
  * New driver and dt binding to support this current monitor used to measure
    power usage.
- yamaha,yas530
  * Support the YAS537 variant (series includes several fixes for other parts
    and new driver features).

Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
  the posted RFC of that framework.

Features
- core
  * Large rework to make all the core IIO code use generic firmware properties.
    Includes switching some drivers over as well using newly provided
    generic interfaces and allowing removal of DT specific ones.
  * Support for gesture event types for single and double tap. Used in
    bosch,bma400.
- atmel,at91-sama5d2
  * Add support for temperature sensor which uses two muxed inputs to estimate
    the temperature.
  * Handle trackx bits of EMR register to improve temp sampling accuracy.
  * Runtime PM support.
- liteon,ltrf216a
  * Add a _raw channel output to allow working around an issue with
    differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
  * Support regulator control.
- ti,tsc2046
  * External reference voltage support.

Clean up and minor fixes
- Tree-wide
  * devm_clk_get_enabled() replacements of opencoded equivalent.
  * Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
  * Various minor warning and similar cleanup such as missing static
    markings.
  * strlcpy() to strscpy() for cases where return value not checked.
  * provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
  * Drop maintainers listss where the email address is bouncing.
  * Switch spi devices over to using spi-peripheral.yaml
  * Add some missing unevaluatedProperties / additionalProperties: false
    entries.
- ABI docs
  * Add some missing channel type specific sampling frequency entries.
  * Add parameter names for callback parameters.
- MAINTAINERS
  * Fix wrong ADI forum links.
- core
  * lockdep class per device, to avoid an issue with nest when one IIO
    device is the consumer of another.
  * White space tweaks.
- asc,dlhl60d
  * Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
  * Fix wrong max value.
  * Improve error handling when measuring pressure and touch.
  * Add locks to remove races on updating oversampling / sampling freq.
  * Add missing calls in suspend and resume path to ensure state is correctly
    brought up if buffered capture was in use when suspend happened.
  * Error out of write_raw() callback if buffered capture enabled to avoid
    unpredictable behavior.
  * Handle different versions having different oversampling ratio support and
    drop excess error checking.
  * Cleanup magic value defines where the name is just the value and hence
    hurts readability.
  * Use read_avail() callback to provide info on possible oversampling ratios.
  * Correctly handle variable bit depth when doing oversampling on different
    supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
  * Don't ignore errors from regulator_get_voltage() so as to avoid some
    very surprising scaling.
- invensense,icp10100
  * Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
    sense and is now deprecated. In this driver we just avoid double disabling
    in some paths.
- maxim,max1363
  * Drop consumer channel map provision by platform data. There have been
    better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
  * Update status to maintained.
- qcom,spmi-adc5
  * Support measurement of LDO output voltage.
- qcom,spmi-adc
  * Add missing channel available on SM6125 SoC.
- st,stmpe
  * Drop requirement on node name in binding now that driver correctly
    doesn't enforce it.
- stx104
  * Move to more appropriate addac directory
- ti,am335x
  * Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
  * Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
  * Minor cleanups.

* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
  iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
  iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
  iio: accel: bma400: Add support for single and double tap events
  iio: Add new event type gesture and use direction for single and double tap
  iio: Use per-device lockdep class for mlock
  iio: adc: add max11205 adc driver
  dt-bindings: iio: adc: Add max11205 documentation file
  iio: magnetometer: yamaha-yas530: Use dev_err_probe()
  iio: magnetometer: yamaha-yas530: Make strings const in chip info
  iio: magnetometer: yamaha-yas530: Use pointers as driver data
  iio: adc: tsc2046: silent spi_device_id warning
  iio: adc: tsc2046: add vref support
  dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
  iio: light: ltrf216a: Add raw attribute
  dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
  MAINTAINERS: fix Analog Devices forum links
  iio/accel: fix repeated words in comments
  dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
  iio: add MEMSensing MSA311 3-axis accelerometer driver
  dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
  ...

Merge tag 'mhi-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next

Manivannan writes:
  "MHI Host
   --------

   - Print the modem name while probing the MHI host pci-generic driver. This has
     been exposed as a debug information so far but on a low storate embedded
     devices such as OpenWRT based products, this helps in identifying the
     attached modem without enabling the debug logs."

* tag 'mhi-for-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
  bus: mhi: host: always print detected modem name

Merge tag 'fpga-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next

Xu writes:

FPGA Manager changes for 6.1-rc1

DFL

- Matthew's change adds new device IDs supported by DFL.
- Dan's change uses array_size() for memory allocation to prevent
potential overflow

Microchip

- Conor's change adds MODULE_AUTHOR entry for microchip-spi driver
- Krzysztof's change refines dt-bindings

Intel m10 bmc secure update

- Russ's change adds new device ID supported by the driver

All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Signed-off-by: Xu Yilun <yilun.xu@intel.com>

* tag 'fpga-for-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
  fpga: m10bmc-sec: d5005 bmc secure update driver
  fpga: prevent integer overflow in dfl_feature_ioctl_set_irq()
  dt-bindings: fpga: microchip,mpf-spi-fpga-mgr: use spi-peripheral-props.yaml
  fpga: microchip-spi: add missing module author entry
  fpga: dfl-pci: Add IDs for Intel N6000, N6001 and C6100 cards

This harmless print provides a very easy way of knowing
if the modem is detected properly during probing.

Promote it to an informational print so no hassle is required
enabling kernel debugging info to obtain it.

The rationale here is that:
On a lot of low-storage embedded devices, extensive kernel
debugging info is not always present as this would
increase it's size to much causing partition size issues.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/20220831100349.1488762-1-koen.vandeputte@citymesh.com
[mani: added missing review tags]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Add a driver name for the D5005 BMC secure update driver. Different
driver names are used for the N3000 and D5005 devices because future
changes will add conditional code based on the device type (N3000
vs D5005). This change enables D5005 secure updates of BCM images,
BMC firmware, static-region images, etc.
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20220902165706.518074-3-russell.h.weight@intel.comSigned-off-by: Xu Yilun <yilun.xu@intel.com>

Follow the advice of the Documentation/filesystems/sysfs.rst
and show() should only use sysfs_emit() or sysfs_emit_at()
when formatting the value to be returned to user space.
Signed-off-by: Xuezhi Zhang <zhangxuezhi1@coolpad.com>
Link: https://lore.kernel.org/r/20220901013423.418464-1-zhangxuezhi3@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dma_map_single() doesn't permit zero length mapping. It causes a follow
panic.

A panic was reported on arm64:

[   60.137988] ------------[ cut here ]------------
[   60.142630] kernel BUG at kernel/dma/swiotlb.c:624!
[   60.147508] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[   60.152992] Modules linked in: dw_hdmi_cec crct10dif_ce simple_bridge rcar_fdp1 vsp1 rcar_vin videobuf2_vmalloc rcar_csi2 v4l
2_mem2mem videobuf2_dma_contig videobuf2_memops pci_endpoint_test videobuf2_v4l2 videobuf2_common rcar_fcp v4l2_fwnode v4l2_asyn
c videodev mc gpio_bd9571mwv max9611 pwm_rcar ccree at24 authenc libdes phy_rcar_gen3_usb3 usb_dmac display_connector pwm_bl
[   60.186252] CPU: 0 PID: 508 Comm: pcitest Not tainted 6.0.0-rc1rpci-dev+ #237
[   60.193387] Hardware name: Renesas Salvator-X 2nd version board based on r8a77951 (DT)
[   60.201302] pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   60.208263] pc : swiotlb_tbl_map_single+0x2c0/0x590
[   60.213149] lr : swiotlb_map+0x88/0x1f0
[   60.216982] sp : ffff80000a883bc0
[   60.220292] x29: ffff80000a883bc0 x28: 0000000000000000 x27: 0000000000000000
[   60.227430] x26: 0000000000000000 x25: ffff0004c0da20d0 x24: ffff80000a1f77c0
[   60.234567] x23: 0000000000000002 x22: 0001000040000010 x21: 000000007a000000
[   60.241703] x20: 0000000000200000 x19: 0000000000000000 x18: 0000000000000000
[   60.248840] x17: 0000000000000000 x16: 0000000000000000 x15: ffff0006ff7b9180
[   60.255977] x14: ffff0006ff7b9180 x13: 0000000000000000 x12: 0000000000000000
[   60.263113] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
[   60.270249] x8 : 0001000000000010 x7 : ffff0004c6754b20 x6 : 0000000000000000
[   60.277385] x5 : ffff0004c0da2090 x4 : 0000000000000000 x3 : 0000000000000001
[   60.284521] x2 : 0000000040000000 x1 : 0000000000000000 x0 : 0000000040000010
[   60.291658] Call trace:
[   60.294100]  swiotlb_tbl_map_single+0x2c0/0x590
[   60.298629]  swiotlb_map+0x88/0x1f0
[   60.302115]  dma_map_page_attrs+0x188/0x230
[   60.306299]  pci_endpoint_test_ioctl+0x5e4/0xd90 [pci_endpoint_test]
[   60.312660]  __arm64_sys_ioctl+0xa8/0xf0
[   60.316583]  invoke_syscall+0x44/0x108
[   60.320334]  el0_svc_common.constprop.0+0xcc/0xf0
[   60.325038]  do_el0_svc+0x2c/0xb8
[   60.328351]  el0_svc+0x2c/0x88
[   60.331406]  el0t_64_sync_handler+0xb8/0xc0
[   60.335587]  el0t_64_sync+0x18c/0x190
[   60.339251] Code: 52800013 d2e00414 35fff45c d503201f (d4210000)
[   60.345344] ---[ end trace 0000000000000000 ]---

To fix it, this patch adds a checking the payload length if it is zero.

Fixes: 343dc693 ("misc: pci_endpoint_test: Prevent some integer overflows")
Cc: stable <stable@kernel.org>
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Link: https://lore.kernel.org/r/20220907020100.122588-2-mie@igel.co.jpSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Each transfer test functions have same parameter checking code. This patch
unites those to an introduced function.
Signed-off-by: Shunsuke Mie <mie@igel.co.jp>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220907020100.122588-1-mie@igel.co.jpSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kmap() is being deprecated in favor of kmap_local_page().

There are two main problems with kmap(): (1) It comes with an overhead as
the mapping space is restricted and protected by a global lock for
synchronization and (2) it also requires global TLB invalidation when the
kmap’s pool wraps and it might block when the mapping space is fully
utilized until a slot becomes available.

With kmap_local_page() the mappings are per thread, CPU local, can take
page faults, and can be called from any context (including interrupts).
It is faster than kmap() in kernels with HIGHMEM enabled. Furthermore,
the tasks can be preempted and, when they are scheduled to run again, the
kernel virtual addresses are restored and still valid.

Since its use in xilinx_sdfec.c is safe, replace kmap()i / kunmap() with
kmap_local_page() / kunmap_local().

Cc: "Venkataramanan, Anirudh" <anirudh.venkataramanan@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220901154408.23984-3-fmdefrancesco@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pages in an array are mapped in a loop but, after the code is done with
the virtual addresses, these pages are never unmapped.

Therefore, call kunmap() to unmap pages[i].

Cc: "Venkataramanan, Anirudh" <anirudh.venkataramanan@intel.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220901154408.23984-2-fmdefrancesco@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kmap() is being deprecated in favor of kmap_local_page().

There are two main problems with kmap(): (1) It comes with an overhead as
the mapping space is restricted and protected by a global lock for
synchronization and (2) it also requires global TLB invalidation when the
kmap’s pool wraps and it might block when the mapping space is fully
utilized until a slot becomes available.

With kmap_local_page() the mappings are per thread, CPU local, can take
page faults, and can be called from any context (including interrupts).
It is faster than kmap() in kernels with HIGHMEM enabled. Furthermore,
the tasks can be preempted and, when they are scheduled to run again, the
kernel virtual addresses are restored and still valid.

Since its use in vmci_queue_pair.c is safe everywhere, replace kmap() with
kmap_local_page().

Cc: "Venkataramanan, Anirudh" <anirudh.venkataramanan@intel.com>
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Link: https://lore.kernel.org/r/20220901135714.16481-1-fmdefrancesco@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When drivers are working properly, they are quiet.
Therefore, the vbg_info() should be removed.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220901144619.3550352-1-jiasheng@iscas.ac.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver core supports the ability to handle the creation and removal
of device-specific sysfs files in a race-free manner. Moreover, it can
guarantee the success of creation. Therefore, it should be better to
convert to use dev_groups.

Fixes: 0ba002bc ("virt: Add vboxguest driver for Virtual Box Guest integration")
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220901144610.3550300-1-jiasheng@iscas.ac.cnSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the module_auxiliary_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

Fixes: 7d3e4d80 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-5-weiyongjun@huaweicloud.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.

Fixes: 7d3e4d80 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-4-weiyongjun@huaweicloud.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The sparse tool complains as follows:

drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.c:409:34: warning:
 symbol 'pci1xxxx_gpio_auxiliary_id_table' was not declared. Should it be static?

This symbol is not used outside of mchp_pci1xxxx_gpio.c, so marks it static.

Fixes: 7d3e4d80 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-3-weiyongjun@huaweicloud.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver allocates the spinlock but not initialize it.
Use spin_lock_init() on it to initialize it correctly.

Fixes: 7d3e4d80 ("misc: microchip: pci1xxxx: load gpio driver for the gpio controller auxiliary device enumerated by the auxiliary bus driver.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-2-weiyongjun@huaweicloud.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In some error handling path, resoures alloced may not released.
This patch fix them.

Fixes: 393fc2f5 ("misc: microchip: pci1xxxx: load auxiliary bus driver for the PIO function in the multi-function endpoint of pci1xxxx device.")
Reviewed-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20220907145808.1789249-1-weiyongjun@huaweicloud.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new entry for VMWARE VSOCK VMCI TRANSPORT DRIVER in the
MAINTAINERS file.
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-4-vdasa@vmware.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change the status from 'Maintained' to 'Supported' for VMWARE
BALLOON DRIVER, VMWARE PVRDMA DRIVER, VMWARE PVSCSI driver,
VMWARE VMCI DRIVER, VMWARE VMMOUSE SUBDRIVER and VMWARE VMXNET3
ETHERNET DRIVER.

This needs to be done to conform to the guidelines in [1].
Maintainers for these drivers are VMware employees.

[1] https://docs.kernel.org/process/maintainers.htmlAcked-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-3-vdasa@vmware.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Change 'VMware PVSCSI driver' entry to upper case.

This is a trivial change being done for uniformity.
Signed-off-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20220906172722.19862-2-vdasa@vmware.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Update the kernel-doc section of struct binder_alloc to fix the
following warnings reported by ./scripts/kernel-doc:

  warning: Function parameter or member 'mutex' not described in 'binder_alloc'
  warning: Function parameter or member 'vma_addr' not described in 'binder_alloc'

No functional changes in this patch.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Acked-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20220906135948.3048225-4-cmllamas@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The mmap_locked asserts here are not needed since this is only called
back from the mmap stack in ->mmap() and ->close() which always acquire
the lock first. Remove these asserts along with binder_alloc_set_vma()
altogether since it's trivial enough to be consumed by callers.

Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20220906135948.3048225-3-cmllamas@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename ->vma_vm_mm to ->mm to reflect the fact that we no longer cache
this reference from vma->vm_mm but from current->mm instead.

No functional changes in this patch.
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Acked-by: Todd Kjos <tkjos@google.com>
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20220906135948.3048225-2-cmllamas@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

build errors and warnings listed below and reported by kernel
test robot <lkp@intel.com> on the char-misc-next branch are
fixed in this add-on patch.

errors:
  ERROR: modpost: "auxiliary_device_init" [drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gp.ko] undefined!
  ERROR: modpost: "__auxiliary_device_add" [drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gp.ko] undefined!
  ERROR: modpost: "auxiliary_driver_unregister" [drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.ko] undefined!
  ERROR: modpost: "__auxiliary_driver_register" [drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.ko] undefined!
  ia64-linux-ld: drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gp.o: in function `gp_aux_bus_probe.part.0':
  mchp_pci1xxxx_gp.c:(.text+0x342): undefined reference to `auxiliary_device_init'
  ia64-linux-ld: mchp_pci1xxxx_gp.c:(.text+0x392): undefined reference to `__auxiliary_device_add'
  ia64-linux-ld: mchp_pci1xxxx_gp.c:(.text+0x5c2): undefined reference to `auxiliary_device_init'
  ia64-linux-ld: mchp_pci1xxxx_gp.c:(.text+0x612): undefined reference to `__auxiliary_device_add'
  ia64-linux-ld: drivers/misc/mchp_pci1xxxx/mchp_pci1xxxx_gpio.o: in function `pci1xxxx_gpio_driver_init':
  mchp_pci1xxxx_gpio.c:(.init.text+0x42): undefined reference to `__auxiliary_driver_register'

warnings:
  unmet direct dependencies detected for GPIOLIB_IRQCHIP when selected by GP_PCI1XXXX

Fixes: 393fc2f5 ("misc: microchip: pci1xxxx: load auxiliary bus driver for the PIO function in the multi-function endpoint of pci1xxxx device.")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Link: https://lore.kernel.org/r/20220906124951.696776-1-kumaravel.thiagarajan@microchip.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The suspend and resume callbacks in this driver appear to be safe
to call repeatedly, but why do so when we can use the
DEFINE_RUNTIME_DEV_PM_OPS() macro to supply callbacks that check if
we are already runtime suspended before doing unnecessary work.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20220807190414.1039028-2-jic23@kernel.org

Back in the days of board files, platform data was used to provide
information on the mapping from ADC channel to an analog signal
from another device. We've long since moved to doing this via
device tree. Hence drop the support from the max1363 driver which is
the only driver still providing this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220821161058.2207185-1-jic23@kernel.org

Add support for single and double tap events based on the tap threshold
value, minimum quiet time before and after the tap and minimum time
between the taps in the double tap. The INT1 pin is used to interrupt
and the event is pushed to userspace.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220831063117.4141-3-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Add new event type for tap called gesture and the direction can be used
to differentiate single and double tap. This may be used by accelerometer
sensors to express single and double tap events. For directional tap,
modifiers like IIO_MOD_(X/Y/Z) can be used along with singletap and
doubletap direction.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220831063117.4141-2-jagathjog1996@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

If an IIO driver uses callbacks from another IIO driver and calls
iio_channel_start_all_cb() from one of its buffer setup ops, then
lockdep complains due to the lock nesting, as in the below example with
lmp91000.

Since the locks are being taken on different IIO devices, there is no
actual deadlock.  Fix the warning by telling lockdep to use a different
class for each iio_device.

 ============================================
 WARNING: possible recursive locking detected
 --------------------------------------------
 python3/23 is trying to acquire lock:
 (&indio_dev->mlock){+.+.}-{3:3}, at: iio_update_buffers

 but task is already holding lock:
 (&indio_dev->mlock){+.+.}-{3:3}, at: enable_store

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&indio_dev->mlock);
   lock(&indio_dev->mlock);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 5 locks held by python3/23:
  #0: (sb_writers#5){.+.+}-{0:0}, at: ksys_write
  #1: (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter
  #2: (kn->active#14){.+.+}-{0:0}, at: kernfs_fop_write_iter
  #3: (&indio_dev->mlock){+.+.}-{3:3}, at: enable_store
  #4: (&iio_dev_opaque->info_exist_lock){+.+.}-{3:3}, at: iio_update_buffers

 Call Trace:
  __mutex_lock
  iio_update_buffers
  iio_channel_start_all_cb
  lmp91000_buffer_postenable
  __iio_update_buffers
  enable_store

Fixes: 67e17300 ("iio: potentiostat: add LMP91000 support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829091840.2791846-1-vincent.whitchurch@axis.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Adding support for max11205 16-bit single-channel ultra-low power
delta-sigma adc.
The MAX11205 is compatible with the 2-wire interface and uses
SCLK and RDY/DOUT for serial communications. In this mode, all
controls are implemented by timing the high or low phase of the SCLK.
The 2-wire serial interface only allows for data to be read out through
the RDY/DOUT output.

Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX11205.pdfSigned-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220831133021.215625-2-ramona.bolboaca@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

We need the char-misc fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull powerpc fixes from Michael Ellerman:

 - Fix handling of PCI domains in /proc on 32-bit systems using the
   recently added support for numbering buses from zero for each domain.

 - A fix and a revert for some changes to use READ/WRITE_ONCE() which
   caused problems with KASAN enabled due to sanitisation calls being
   introduced in low-level paths that can't cope with it.

 - Fix build errors on 32-bit caused by the syscall table being
   misaligned sometimes.

 - Two fixes to get IBM Cell native machines booting again, which had
   bit-rotted while my QS22 was temporarily out of action.

 - Fix the papr_scm driver to not assume the order of events returned by
   the hypervisor is stable, and a related compile fix.

Thanks to Aneesh Kumar K.V, Christophe Leroy, Jordan Niethe, Kajol Jain,
Masahiro Yamada, Nathan Chancellor, Pali Rohár, Vaibhav Jain, and Zhouyi
Zhou.

* tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
  Revert "powerpc/irq: Don't open code irq_soft_mask helpers"
  powerpc: Fix hard_irq_disable() with sanitizer
  powerpc/rtas: Fix RTAS MSR[HV] handling for Cell
  Revert "powerpc: Remove unused FW_FEATURE_NATIVE references"
  powerpc: align syscall table for ppc32
  powerpc/pci: Enable PCI domains in /proc when PCI bus numbers are not unique
  powerpc/papr_scm: Fix nvdimm event mappings

Pull kvm fixes from Paolo Bonzini:
 "s390:

   - PCI interpretation compile fixes

  RISC-V:

   - fix unused variable warnings in vcpu_timer.c

   - move extern sbi_ext declarations to a header

  x86:

   - check validity of argument to KVM_SET_MP_STATE

   - use guest's global_ctrl to completely disable guest PEBS

   - fix a memory leak on memory allocation failure

   - mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES

   - fix build failure with Clang integrated assembler

   - fix MSR interception

   - always flush TLBs when enabling dirty logging"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: check validity of argument to KVM_SET_MP_STATE
  perf/x86/core: Completely disable guest PEBS via guest's global_ctrl
  KVM: x86: fix memoryleak in kvm_arch_vcpu_create()
  KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
  KVM: s390: pci: Hook to access KVM lowlevel from VFIO
  riscv: kvm: move extern sbi_ext declarations to a header
  riscv: kvm: vcpu_timer: fix unused variable warnings
  KVM: selftests: Fix ambiguous mov in KVM_ASM_SAFE()
  KVM: selftests: Fix KVM_EXCEPTION_MAGIC build with Clang
  KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
  kvm: x86: mmu: Always flush TLBs when enabling dirty logging
  kvm: x86: mmu: Drop the need_remote_flush() function

-Wformat was recently re-enabled for builds with clang, then quickly
re-disabled, due to concerns stemming from the frequency of default
argument promotion related warning instances.

commit 258fafcd ("Makefile.extrawarn: re-enable -Wformat for clang")
commit 21f9c8a1 ("Revert "Makefile.extrawarn: re-enable -Wformat for clang"")

ISO WG14 has ratified N2562 to address default argument promotion
explicitly for printf, as part of the upcoming ISO C2X standard.

The behavior of clang was changed in clang-16 to not warn for the cited
cases in all language modes.

Add a version check, so that users of clang-16 now get the full effect
of -Wformat. For older clang versions, re-enable flags under the
-Wformat group that way users still get some useful checks related to
format strings, without noisy default argument promotion warnings. I
intentionally omitted -Wformat-y2k and -Wformat-security from being
re-enabled, which are also part of -Wformat in clang-16.

Link: https://github.com/ClangBuiltLinux/linux/issues/378
Link: https://github.com/llvm/llvm-project/issues/57102
Link: https://www.open-std.org/jtc1/sc22/wg14/www/docs/n2562.pdfSuggested-by: Justin Stitt <jstitt007@gmail.com>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add bindings documentation file and MAINTAINERS entry for MAX11205.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220831133021.215625-1-ramona.bolboaca@analog.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Unify error message format by using dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220831141530.80572-3-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

For better compiler coverage mark strings consts in the chip info.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220831141530.80572-2-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

Unify ID tables to use pointers for driver data. It will allow
to simplify the driver later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220831141530.80572-1-andriy.shevchenko@linux.intel.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>