- 24 Feb, 2022 1 commit
-
-
Mark Brown authored
The smb347 has a very sparse register map (the maximum register is 0x3f but less than 10% of the possible registers appear to be defined) and doesn't have any hardware defaults specified so the sparser data structure of an rbtree is a better fit for it's needs than a flat cache. Since it uses I2C for the control interface there is no performance concern with the slightly more involved code so let's convert it. This will mean we avoid any issues created by assuming that any previously unaccessed registers hold a value that doesn't match what's in the hardware (eg, an _update_bits() suppressing a write). Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com>
-
- 13 Feb, 2022 7 commits
-
-
Hans de Goede authored
The AXP288's recommended and factory default Vhold value (minimum input voltage below which the input current draw will be reduced) is 4.4V. This lines up with other charger IC's such as the TI bq2419x/bq2429x series which use 4.36V or 4.44V. For some reason some BIOS-es initialize Vhold to 4.6V or even 4.7V which combined with the typical voltage drop over typically low wire gauge micro-USB cables leads to the input-current getting capped below 1A (with a 2A capable dedicated charger) based on Vhold. This leads to slow charging, or even to the device slowly discharging if the device is in heavy use. As the Linux AXP288 drivers use the builtin BC1.2 charger detection and send the input-current-limit according to the detected charger there really is no reason not to use the recommended 4.4V Vhold. Set Vhold to 4.4V to fix the slow charging issue on various devices. There is one exception, the special-case of the HP X2 2-in-1s which combine this BC1.2 capable PMIC with a Type-C port and a 5V/3A factory provided charger with a Type-C plug which does not do BC1.2. These have their input-current-limit hardcoded to 3A (like under Windows) and use a higher Vhold on purpose to limit the current when used with other chargers. To avoid touching Vhold on these HP X2 laptops the code setting Vhold is added to an else branch of the if checking for these models. Note this also fixes the sofar unused VBUS_ISPOUT_VHOLD_SET_MASK define, which was wrong. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Changcheng Deng authored
Remove unneeded variable used to store return value. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Changcheng Deng <deng.changcheng@zte.com.cn> Signed-off-by:
-
Michał Mirosław authored
Replace dev_err() with dev_err_probe() in probe() and extend register access failure messages. dev_err()s in _reset() are removed as they are redundant: register access wrappers already log the error. Signed-off-by:
Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by:
-
Michał Mirosław authored
Replace two divisions with a subtraction+shift for a small code size improvement and less brackets. Signed-off-by:
-
Hong Peng authored
fix the comment typo: "interrupts", "structcure" Signed-off-by:
Hong Peng <elicec@foxmail.com> Signed-off-by:
-
Miaoqian Lin authored
kobject_init_and_add() takes reference even when it fails. According to the doc of kobject_init_and_add()： If this function returns an error, kobject_put() must be called to properly clean up the memory associated with the object. Fix memory leak by calling kobject_put(). Fixes: 8c0984e5 ("power: move power supply drivers to power/supply") Signed-off-by:
Miaoqian Lin <linmq006@gmail.com> Signed-off-by:
-
Daisuke Nojiri authored
This change makes the PCHG driver receive device events through MKBP protocol since CrOS EC switched to deliver all peripheral charge events to the MKBP protocol. This will unify PCHG event handling on X86 and ARM. Signed-off-by:
Daisuke Nojiri <dnojiri@chromium.org> Signed-off-by:
-
- 11 Feb, 2022 22 commits
-
-
Linus Walleij authored
When using USB charging, the AB8500 charger is periodically checking VBAT for a threshold at 3.8V. This crashes badly, as the class_for_each_device() was passed the wrong argument. I think this has maybe worked by chance in the past because of how the structs were arranged but it is leading to crashes now. Fix this up and also switch to using microvolts for the voltages like the rest of the code. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Linus Walleij authored
The AB8505 only has two ADC channels: the voltage and current provided from VBUS (USB). It does not support AC charging at all. Make sure we don't try to retrieve the non-existing channels. Signed-off-by:
-
Linus Walleij authored
There is a sysfs ABI to enable/disable charging of different types (AC/USB). Since we don't have any userspace for this code, this sits unused and it is not used on production products either. Drop this code. Signed-off-by:
-
Linus Walleij authored
There is a sysfs ABI to change the "charging step" of the charger i.e. limit how much we charge from userspace. Since we don't have any userspace for this code, this sits unused and it is not used on production products either. Drop this code. Signed-off-by:
-
Linus Walleij authored
All calls to ab8500_fg_calc_cap_discharge_voltage() require compensation and pass true as the second argument so just drop this argument. Signed-off-by:
-
Linus Walleij authored
In some cases when the platform is dissapating more than 500mA the voltage measurements and compensation will become instable. Add a parameter to bail out of the voltage measurement if this happens. This code was found in a Samsung vendor tree. Signed-off-by:
-
Linus Walleij authored
Break out the part of the function providing the load compensated capacity that provides the load compensated voltage and use that to get the load compensated capacity. Signed-off-by:
-
Linus Walleij authored
In the Samsung code tree we find that it can happen that this measurement loop goes on for a long time, and it seems like a good idea to break it after 70 iterations if it goes on for too long. Signed-off-by:
-
Linus Walleij authored
Instead of providing our own homebrewn thermal measurement code for an NTC and passing tables, we put the NTC thermistor into the device tree, create a passive thermal zone, and poll this thermal zone for the temperature. Signed-off-by:
-
Linus Walleij authored
We should terminate charging when we reach the voltage_max_design_uv not overvoltage_limit_uv, this is an abuse of that struct member. The overvoltage limit is actually not configurable on the AB8500, it is fixed to 4.75 V so drop a comment about that in the code. Fixes: 2a5f4183 ("power: supply: ab8500: Standardize voltages") Signed-off-by:
-
Linus Walleij authored
The BATCTRL mode reads the temperature of the battery by enabling a certain probing current (7-20 mA) and then measure the voltage of the NTC mounted inside the battery. None of the AB8500 product or the reference designs use this mode. What we use is the so-called BATTEMP mode which enables an internal 230 kOhm pull-up to 1.8 V to the external NTC on pin BatTemp (N16) and then measures the voltage over the NTC using the ADC: 1.8V (VTVOUT) | [ ] 230 kOhm | BatTemp +---------------- ADC Pin N16 | _ |/ [/] NTC _/| | GND Cut out the BATCTRL code to clear the forest and stop maintaining code we can never test. The current inducing method is still used to probe for the battery type using the internal BTI (battery type indicator) on the BatCtrl (C3) pin in a separate code path. Signed-off-by: -
Andy Shevchenko authored
Use device_property_string_array_count() to get number of strings in a string array property. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Uwe Kleine-König authored
When ret is not zero there were already one or two error messages emitted about a problem (because rt9455_register_reset() emits a message in most cases then). Passing on that error code to the i2c core only results in another error message. Suppress that by returning zero unconditionally. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Christophe JAILLET authored
Use devm_bitmap_zalloc() instead of hand writing it. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Hans de Goede authored
Add a new battery driver for the uPI uG3105 battery monitor. Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead it is expected to be use in combination with some always on microcontroller reading its coulomb-counter before it can wrap (must be read every 400 seconds!). Since Linux does not monitor coulomb-counter changes while the device is off or suspended, the coulomb counter is not used atm. So far this driver is only used on x86/ACPI (non devicetree) devs (also note there is no of_match table). Therefor there is no devicetree bindings documentation for this driver's "upisemi,rsns-microohm" property since this is not used in actual devicetree files and the dt bindings maintainers have requested properties with no actual dt users to _not_ be added to the dt bindings. The property's name has been chosen so that it should not need to be changed if/when devicetree enumeration support gets added later, as it mirrors "maxim,rsns-microohm" from the "maxim,max17042" bindings. Signed-off-by:
-
Hans de Goede authored
If the fwnode data as parsed by power_supply_get_battery_info() provides max values for ccc_ireg and cvc_vreg then do not allow the user to later set these to higher values then those specified by the firmware, otherwise the battery might get damaged. Signed-off-by:
-
Hans de Goede authored
So far the bq24190_charger driver has been relying on either the chips default constant_charge_current_max_ua and constant_charge_voltage_max_uv values, or on the BIOS or bootloader to program these for us. This does not happen on all boards, causing e.g. the wrong (too low) values to be used on Lenovo Yoga Tablet 2 830F/L and 1050F/L tablets. If power_supply_get_battery_info() provides us with values for these settings, then program the charger accordingly. And if the user later overrides these values then save the user-values so that these will be restored after a suspend/resume. Signed-off-by:
-
Hans de Goede authored
Store ichg-max and vreg-max in bq24190_dev_info once from bq24190_get_config() and drop the bq24190_charger_get_current_max() and bq24190_charger_get_voltage_max() helpers. This is a preparation patch for honoring the constant_charge_current_max_ua and constant_charge_voltage_max_uv values from power_supply_get_battery_info(). Signed-off-by:
-
Hans de Goede authored
power_supply_get_battery_info() now also supports getting battery_info on boards not using dt/of. Remove the of_node check. If neither of nor other battery-info is present the function will fail making this change a no-op in that case. Signed-off-by:
-
Hans de Goede authored
Turn off the 5V boost regulator on shutdown, there are 3 reasons for doing this: 1. It drains he battery if left on 2. If left on the device will not charge when plugged into a charger 3. If left on and the powered peripheral attached to a Type-C port is removed before the next boot, then the Type-C port-controller will see VBus being present while nothing is attached confusing the TCPM state-machine. Signed-off-by:
-
Hans de Goede authored
Add support to power_supply_get_battery_info() to read the properties from other fwnode types such as swnodes added by platform code on x86 devices. Signed-off-by:
-
Hans de Goede authored
Switch power_supply_get_battery_info() over to use the generic fwnode_property_*() property read functions. This is a preparation patch for adding support for reading properties from other fwnode types such as swnode properties added by platform code on x86 devices. Note the parsing of the 2d matrix "ocv-capacity-table-%d" and "resistance-temp-table" properties is not converted since this depends on the raw of_get_property() accessor function of which there is no fwnode_property_*() equivalent AFAICT. This means that these properties will not be supported in swnodes for now. Signed-off-by:
-
- 02 Feb, 2022 1 commit
-
-
Colin Ian King authored
There is a spelling mistake in a MODULE_PARM_DESC description. Fix it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Acked-by:
-
- 01 Feb, 2022 9 commits
-
-
Sebastian Reichel authored
Immutable branch between power-supply, mfd, i2c and extcon for for 5.18 This immutable branch fixes the charger setup on Xiaomi Mi Pad 2 and Lenovo Yogabook, which requires updates to multiple drivers throughout the tree. Signed-off-by:Sebastian Reichel <sre@kernel.org>
-
Hans de Goede authored
Make cht_wc_extcon_get_id() report RID_A for ACA adapters, instead of reporting ID_FLOAT. According to the spec. we should read the USB-ID pin ADC value to determine the resistance of the used pull-down resister and then return RID_A / RID_B / RID_C based on this. But all "Accessory Charger Adapter"s (ACAs) which users can actually buy always use a combination of a charging port with one or more USB-A ports, so they should always use a resistor indicating RID_A. But the spec is hard to read / badly-worded so some of them actually indicate they are a RID_B ACA even though they clearly are a RID_A ACA. To workaround this simply always return INTEL_USB_RID_A, which matches all the ACAs which users can actually buy. Acked-by:
Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by:
-
Hans de Goede authored
The bq25890 used on the Yogabook YB1-X90 / -X91 models relies on the extcon-driver's BC-1.2 charger detection, and the bq25890 driver expect this info to be available through a parent power_supply class-device which models the detected charger (idem to how the Type-C TCPM code registers a power_supply classdev for the connected charger). Add support for registering the power_supply class-device expected by this setup. Acked-by:
-
Hans de Goede authored
This is a preparation patch for adding support for registering a power_supply class device. Setting usbsrc to "CHT_WC_USBSRC_TYPE_SDP << CHT_WC_USBSRC_TYPE_SHIFT" will make the following switch-case return EXTCON_CHG_USB_SDP just as before, so there is no functional change. Acked-by:
-
Hans de Goede authored
So far the extcon-intel-cht-wc code has only been tested on devices with a Type-C connector with USB-PD, USB3 (superspeed) and DP-altmode support through a FUSB302 Type-C controller. Some devices with the intel-cht-wc PMIC however come with an USB-micro-B connector, or an USB-2 only Type-C connector without USB-PD. Which device-model we are running on can be identified with the new cht_wc_model intel_soc_pmic field. On models without a Type-C controller the extcon code must control the Vbus 5V boost converter and the USB role switch depending on the detected cable-type. Acked-by:
-
Hans de Goede authored
The CHT_WC_VBUS_GPIO_CTLO GPIO actually driving an external 5V Vboost converter for Vbus depends on the board on which the Cherry Trail - Whiskey Cove PMIC is actually used. Since the information about the exact PMIC setup is necessary in other places too, struct intel_soc_pmic now has a new cht_wc_model field indicating the board model. Only poke the CHT_WC_VBUS_GPIO_CTLO GPIO if this new field is set to INTEL_CHT_WC_GPD_WIN_POCKET, which indicates the Type-C (with PD and DP-altmode) setup used on the GPD pocket and GPD win; and on which this GPIO actually controls an external 5V Vboost converter. Acked-by:
-
Hans de Goede authored
The i2c-controller on the Cherry Trail - Whiskey Cove PMIC is special in that it is always connected to the I2C charger IC of the board on which the PMIC is used; and the charger IC is not described in ACPI, so the i2c-cht-wc code needs to instantiate an i2c-client for it itself. So far this was hardcoded to instantiate an i2c-client for the bq24292i, with all properties, etc. set to match how this charger is used on the GPD win and GPD pocket devices. There is a rudimentary check to make sure the ACPI tables are at least somewhat as expected, but this is far from accurate, leading to a wrong i2c-client being instantiated for the charger on some boards. Switch to the new DMI based intel_cht_wc_get_model() helper which is exported by the MFD driver for the CHT Whiskey Cove PMIC to help PMIC cell drivers like the i2c-cht-wc code reliably detect which board they are running on. And add board_info for the charger ICs as found on the other 2 known boards with a Whisky Cove PMIC. This has been tested on all 3 known boards. Acked-by:
Wolfram Sang <wsa@kernel.org> Reviewed-by:
-
Hans de Goede authored
Tablet / laptop designs using an Intel Cherry Trail x86 main SoC with an Intel Whiskey Cove PMIC do not use a single standard setup for the charger, fuel-gauge and other chips surrounding the PMIC / charging+data USB port. Unlike what is normal on x86 this diversity in designs is not handled by the ACPI tables. On 2 of the 3 known designs there are no standard (PNP0C0A) ACPI battery devices and on the 3th design the ACPI battery device does not work under Linux due to it requiring non-standard and undocumented ACPI behavior. So to make things work under Linux we use native charger and fuel-gauge drivers on these devices, re-using the native drivers used on ARM boards with the same charger / fuel-gauge ICs. This requires various MFD-cell drivers for the CHT-WC PMIC cells to know which model they are exactly running on so that they can e.g. instantiate an I2C-client for the right model charger-IC (the charger is connected to an I2C-controller which is part of the PMIC). Rather then duplicating DMI-id matching to check which model we are running on in each MFD-cell driver, add a check for this to the shared drivers/mfd/intel_soc_pmic_chtwc.c code by using a DMI table for all 3 known models: 1. The GPD Win and GPD Pocket mini-laptops, these are really 2 models but the Pocket re-uses the GPD Win's design in a different housing: The WC PMIC is connected to a TI BQ24292i charger, paired with a Maxim MAX17047 fuelgauge + a FUSB302 USB Type-C Controller + a PI3USB30532 USB switch, for a fully functional Type-C port. 2. The Xiaomi Mi Pad 2: The WC PMIC is connected to a TI BQ25890 charger, paired with a TI BQ27520 fuelgauge, using the TI BQ25890 for BC1.2 charger type detection, for a USB-2 only Type-C port without PD. 3. The Lenovo Yoga Book YB1-X90 / Lenovo Yoga Book YB1-X91 series: The WC PMIC is connected to a TI BQ25892 charger, paired with a TI BQ27542 fuelgauge, using the WC PMIC for BC1.2 charger type detection and using the BQ25892's Mediatek Pump Express+ (1.0) support to enable charging with up to 12V through a micro-USB port. Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Hans de Goede authored
Use the devm_regmap_field_bulk_alloc() helper function instead of open-coding this ourselves. Reviewed-by:
-
