This patch guarantees that the VFs do not have access to VLANs that they
were not supposed to.  What this patch does is add code so that we delete
the previous port VLAN after adding a new one, and if we reset the VF we
clear all of the filters associated with it.

Previously the code was leaving all previous VLANs mapped to the VF and
they didn't get deleted unless the VF specifically requested it or if the
PF itself was reset.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch makes certain that we clear the pool mappings added when we
configure default MAC addresses for the interface.  Without this we run the
risk of leaking an address into pool 0 which really belongs to VF 0 when
SR-IOV is enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is a follow-on for enabling VLAN promiscuous and allowing the PF
to add VLANs without adding a VLVF entry.  What this patch does is go
through and free the VLVF registers if they are not needed as the VLAN
belongs only to the PF which is the default pool.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for VLAN promiscuous with SR-IOV enabled.

The code prior to this patch was only adding the PF to VLANs that the VF
had added.  As such enabling promiscuous mode would actually not add any
additional VLAN filters so visibility was limited.  This lead to a number
of issues as the bridge and OVS would expect us to accept all VLAN tagged
packets when promiscuous mode was enabled, and instead we would filter out
most if not all depending on the configuration of the PF.

With this patch what we do is set all the bits in the VFTA and all of the
VLVF bits associated with the pool belonging to the PF.  By doing this the
PF is guaranteed to receive all VLAN tagged traffic associated with the RAR
filters assigned to the PF.  In addition we will clean up those same bits
in the event of promiscuous mode being disabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to reduce the complexity of the search function used
for finding a VLVF entry associated with a given VLAN ID.  The previous
code was searching from bottom to top.  I reordered it to search from top
to bottom.  In addition I pulled an AND statement out of the loop and
instead replaced it with an OR statement outside the loop.  This should
help to reduce the overall size and complexity of the function.

There was also some formatting I cleaned up in regards to whitespace and
such.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for bypassing the VLVF entry creation when the PF
is adding a new VLAN.  The advantage to doing this is that we can then save
the VLVF entries for the VFs which must have them in order to function,
versus the PF which can fall back on the default pool entry.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch addresses several issues within the VLVF and VLVFB
configuration

First was the fact that code was overly complicated with multiple
conditional paths depending on if we adding or removing and which bit we
were going to add or remove.  Instead of messing with all that I have
simplified it by using (vid / 32) and (1 - vid / 32) to identify our
register and the other vlvfb register.

Second was the fact that we were likely leaking a few packets into the PF
in cases where we were deleting an entry and the VFTA filter for that entry
as the ordering was such that we deleted the pool and then the VLAN filter
instead of the other way around.  I have updated that by adding a check for
no bits being set and if that occurs we clear things up in the proper
order.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In order to clear the way for upcoming work I thought it best to drop the
level of indent in the ixgbe_set_vfta_generic function.  Most of the code
is held in the virtualization specific section.  So the easiest approach is
to just add a jump label and jump past the bulk of the code if it is not
enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch simplifies the logic for setting the VFTA register by removing
the number of conditional checks needed.  Instead we just use some boolean
logic to generate vfta_delta, and if that is set then we xor the vfta by
that value and write it back.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The code for checking the PF bit in ixgbe_set_vf_vlan_msg was using the
wrong offset and as a result it was pulling the VLAN off of the PF even if
there were VFs numbered greater than 40 that still had the VLAN enabled.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a check to make certain mac_table was actually allocated and is not
NULL.  If it is NULL return -ENOMEM and allow the probe routine to fail
rather then causing a NULL pointer dereference further down the line.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Saeed Mahameed says:

====================
mlx5 improved flow steering management

First two patches fixes some minor issues in recently
introduced SRIOV code.

The other seven patches modifies the driver's code that
manages flow steering rules with Connectx-4 devices.

Basic introduction:

The flow steering device specification model is composed of the following entities:

Destination (either a TIR/Flow table/vport), where TIR is RSS end-point, vport
is the VF eSwitch port in SRIOV.

Flow table entry (FTE) - the values used by the flow specification
Flow table group (FG) - the masks used by the flow specification
Flow table (FT) - groups several FGs and can serve as destination

The flow steering software entities:

In addition to the device objects, the software have two more objects:

Priorities - group several FTs. Handles order of packet matching.

Namespaces - group several priorities. Namespace are used in order to
isolate different usages of steering (for example, add two separate
namespaces, one for the NIC driver and one for E-Switch FDB).

The base data structure for the flow steering management is a tree and
all the flow steering objects such as (Namespace/Flow table/Flow Group/FTE/etc.)
are represented as a node in the tree, e.g.:
Priority-0 -> FT1 -> FG -> FTE -> TIR (destination)
Priority-1 -> FT2 -> FG->  FTE -> TIR (destination)

Matching begins in FT1 flow rules and if there is a miss on all the FTEs
then matching continues on the FTEs in FT2.

The new implementation solves/improves the following
issues in the current code:

1) The new impl. supports multiple destinations, the search for existing rule with
   the same matching value is performed by the flow steering management.
   In the current impl. the E-switch FDB management code needs to search
   for existing rules before calling to the add rule function.

2) The new impl. manages the flow table level, in the current implementation the
   consumer states the flow table level when new flow table is created without
   any knowledge about the levels of other flow tables.

3) In the current impl. the consumer can't create or destroy flow
   groups dynamically, the flow groups are passed as argument to the create
   flow table API. The new impl. exposes API for create/destroy flow group.

The series is built as follows:

Patch #1 add flow steering API firmware commands.

Patch #2 add tree operation of the flow steering tree: add/remove node,
initialize node and take reference count on a node.

Patch #3 add essential algorithms for managing the flow steering.

Patch #4 Initialize the flow steering tree, flow steering initialization is based
on static tree which illustrates the flow steering tree when the driver is loaded.

Patch #5 is the main patch of the series. It introduce the flow steering API.

Patch #6 Expose the new flow steering API and remove the old one.
The Ethernet flow steering follows the existing implementation,
but uses the new steering API.

Patch #7 Rename en_flow_table.c to en_fs.c in order to be aligned with
the new flow steering files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename en_flow_table.c to en_fs.c in order to be aligned
with the new flow steering files.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Expose the new flow steering API and remove the old
one.

Few changes are required:

1. The Ethernet flow steering follows the existing implementation, but uses
the new steering API. The old flow steering implementation is removed.

2. Move the E-switch FDB management to use the new API.

3. When driver is loaded call to mlx5_init_fs which initialize
the flow steering tree structure, open namespaces for NIC receive
and for E-switch FDB.

4. Call to mlx5_cleanup_fs when the driver is unloaded.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Flow steering initialization is based on static tree which
illustrates the flow steering tree when the driver is loaded. The
initialization considers the max supported flow table level of the device,
a minimum of 2 kernel flow tables(vlan and mac) are required to have
kernel flow table functionality.

The tree structures when the driver is loaded:

		root_namespace(receive nic)
			  |
		priority-0 (kernel priority)
			  |
		namespace(kernel namespace)
			  |
		priority-0 (flow tables priority)

In the following patches, When the EN driver will use the flow steering
API, it create two flow tables and their flow groups under
priority-0(flow tables priority).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introducing the following objects:

mlx5_flow_root_namespace: represent the root of specific flow table
type tree(e.g NIC receive, FDB, etc..)

mlx5_flow_group: define the mask of the flow specification.

fs_fte(flow steering flow table entry): defines the value of the
flow specification.

The following describes the relationships between the tree objects:
root_namespace --> priorities -->namespaces -->
priorities -->flow-tables --> flow-groups -->
flow-entries --> destinations

When we create new object(flow table/flow group/flow table entry), we
call to the FW command and then we add the related sw object to the tree.

When we destroy object, e.g. call to mlx5_destroy_flow_table, we use
the tree node destructor for destroying the FW object and remove the
node from the tree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce the flow steering mlx5_flow_namespace (Namespace)
and fs_prio (Flow Steering Priority) tree nodes.

Namespaces are used in order to isolate different usages or types
of steering (for example, downstream patches will add a different
namespaces for the NIC driver and for E-Switch FDB usages).

Flow Steering Priorities are objects that describes priorities
ranges between different flow objects under the same namespace.

Example, entries in priority i are matched before entries
in priority i+1.

This patch adds the following algorithms:

1) Calculate level:
Each flow table has level(the priority between the flow tables).
When we initialize the flow steering tree, we assign range of levels
to each priority, therefore the level for new flow table is
the location within the priority related to the range of the priority.

2) Match between match criteria. This function is used
for searching flow group when new flow rule is added.

3) Match between match values. This function is used
for searching flow table entry  when new flow rule is added.

4) Add essential macros for traversing on a node's children.
E.g. traversing on all the flow table of some priority
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introducing the base data structure and its operations that are
going to represent ConnectX-4 Flow Steering, this data structure
is basically a tree and all Flow steering objects such as
(Flow Table/Flow Group/FTE/etc ..) are represented as fs_node(s).

fs_node is the base object which describes a basic tree node, with the
following extra info:
    type: describes the runtime type of the node (Object).
    lock: lock this node sub-tree.
    ref_count: number of children + current references.
    remove_func: a generic destructor.

fs_node types will be used and explained once the usage is added in the
following patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under SRIOV there might be a case where VFs are loaded
without pre-assigned MAC address. In this case, the VF
will randomize its own MAC.  This will address the case
of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

E-Switch capabilities should be queried only if E-Switch flow table
is supported and not only when vport group manager.

Fixes: d6666753 ("net/mlx5: E-Switch, Introduce HCA cap and E-Switch vport context")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sunil Goutham says:

====================
net: thunderx: Support for pass-2 hw features

This patch set adds support for new features added in pass-2 revision
of hardware like TSO and count based interrupt coalescing.

Changes from v1:
- Addressed comments received regarding boolean bit field changes
  by excluding them from this patch. Will submit a seperate
  patch along with cleanup of unsed field.
- Got rid of new macro 'VNIC_NAPI_WEIGHT' introduced in
  count threshold interrupt patch.
====================
Reviewed-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This feature is introduced in pass-2 chip and with this CQ interrupt
coalescing will work based on both timer and count.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for offloading TCP segmentation to HW in pass-2
revision of hardware. Both driver level SW TSO for pass1.x chips
and HW TSO for pass-2 chip will co-exist. Modified SQ descriptor
structures to reflect pass-2 hw implementation.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Phy properties are expected to be found in the PHY OF node. However
this Micrel driver also allows them to be placed into the MAC OF node.
This is deprecated. Document it as such, and remove the example using
the deprecated method to prevent people copying it into new device
tree files.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gregory CLEMENT says:

====================
mvneta: Introduce RSS support and XPS configuration

this series is the first step add RSS support on mvneta.

It will allow associating an ethernet interface to a given CPU through
RSS by using "ethtool -X ethX weight". Indeed, currently I only enable
one entry in the RSS lookup table. Even if it is not really RSS, it
allows to get back the irq affinity feature we lost by using the
percpu interrupt.

The main change compared to the second version is the setup for the XPS
instead of using specific hack inside the driver in the forth
patch.

Th first patch make the default queue associate to each port and no
more a global variable.

The second patch really associates the RX queues with the CPUs instead
of masking the percpu interrupts for doing it. All the RX queues are
enabled and are statically associated with the CPUs by using a modulo
of the number of present CPUs. But at this stage only one RX queue
will receive the stream.

The third patch introduces a first level of RSS support through the
ethtool functions. As explained in the introduction there is only one
entry in the RSS lookup table which permits at the end to associate an
mvneta port to a CPU through the RX queues because the mapping is
static.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With this patch each CPU is associated with its own set of TX queues.

It also setup the XPS with an initial configuration which set the
affinity matching the hardware configuration.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support for the RSS related ethtool
function. Currently it only uses one entry in the indirection table which
allows associating an mvneta interface to a given CPU.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We enable the percpu interrupt for all the CPU and we just associate a
CPU to a few queue at the neta level. The mapping between the CPUs and
the queues is static. The queues are associated to the CPU module the
number of CPUs. However currently we only use on RX queue for a given
Ethernet port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of using the same default queue for all the port. Move it in the
port struct. It will allow have a different default queue for each port.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This gets rid of the following compile warn:
net/mpls/mpls_iptunnel.c:40:5: warning: no previous prototype for
mpls_output [-Wmissing-prototypes]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a warn message when clip table overflows. If clip table isn't
allocated, return from cxgb4_clip_release() to avoid panic.
Disable offload if clip isn't enabled in the hardware.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "err = " assignment is missing here.

Fixes: 0d65fc13 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.

Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21:    expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21:    got restricted __le32 *<noident>

This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:

drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]

This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.

Looking at that code in more detail to fix the warnings, I see multiple
related problems:

* The conversion functions are not endian-safe, as the DMA descriptors
  are almost certainly fixed-endian, but the CPU is not.

* On 64-bit machines, passing a pointer through a u32 variable is a
  bug, accessing an indirect pointer as a u32 pointer even more so.

* The handling of epib and psdata mixes native-endian and device-endian
  data.

In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_cgroup_data is a struct containing an anonymous union.
sock_cgroup_set_prioidx() and sock_cgroup_set_classid() were
initializing a field inside the anonymous union as follows.

 struct sock_ccgroup_data skcd_buf = { .val = VAL };

While this is fine on more recent compilers, gcc-4.4.7 triggers the
following errors.

 include/linux/cgroup-defs.h: In function ‘sock_cgroup_set_prioidx’:
 include/linux/cgroup-defs.h:619: error: unknown field ‘val’ specified in initializer
 include/linux/cgroup-defs.h:619: warning: missing braces around initializer
 include/linux/cgroup-defs.h:619: warning: (near initialization for ‘skcd_buf.<anonymous>’)

This is because .val belongs to the anonymous union nested inside the
struct but the initializer is missing the nesting.  Fix it by adding
an extra pair of braces.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alaa Hleihel <alaa@dev.mellanox.co.il>
Fixes: bd1060a1 ("sock, cgroup: add sock->sk_cgroup")
Signed-off-by: David S. Miller <davem@davemloft.net>

The cmac_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.

A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.

Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>