- 13 May, 2014 29 commits
-
-
Felix Fietkau authored
commit 764152ff upstream. Their power value is initialized to zero. This patch fixes an issue where the configured power drops to the minimum value when AP_VLAN interfaces are created/removed. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johannes Berg authored
commit 115b943a upstream. Jouni reported that when doing off-channel transmissions mixed with on-channel transmissions, the on-channel ones ended up on the off-channel in some cases. The reason for that is that during the refactoring of the off- channel code, I lost the part that stopped all activity and as a consequence the on-channel frames (including data frames) were no longer queued but would be transmitted on the temporary channel. Fix this by simply restoring the lost activity stop call. Fixes: 2eb278e0 ("mac80211: unify SW/offload remain-on-channel") Reported-by:
Jouni Malinen <j@w1.fi> Signed-off-by:
-
Michael Braun authored
commit 112c44b2 upstream. commit de74a1d9 "mac80211: fix WPA with VLAN on AP side with ps-sta" fixed an issue where queued multicast packets would be sent out encrypted with the key of an other bss. commit "7cbf9d01" "mac80211: fix oops on mesh PS broadcast forwarding" essentially reverted it, because vif.type cannot be AP_VLAN due to the check to vif.type in ieee80211_get_buffered_bc before. As the later commit intended to fix the MESH case, fix it by checking for IFTYPE_AP instead of IFTYPE_AP_VLAN. Fixes: 7cbf9d01 ("mac80211: fix oops on mesh PS broadcast forwarding") Signed-off-by:
Michael Braun <michael-dev@fami-braun.de> Signed-off-by:
-
Emmanuel Grumbach authored
commit 82e5a649 upstream. There is a flow in which we send the host command in SYNC mode, but we don't take priv->mutex. Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1046495Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Dan Williams authored
commit 8a4aeec8 upstream. The AHCI spec allows implementations to issue commands in tag order rather than FIFO order: 5.3.2.12 P:SelectCmd HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1) or HBA selects the command to issue that has had the PxCI bit set to '1' longer than any other command pending to be issued. The result is that commands posted sequentially (time-wise) may play out of sequence when issued by hardware. This behavior has likely been hidden by drives that arrange for commands to complete in issue order. However, it appears recent drives (two from different vendors that we have found so far) inflict out-of-order completions as a matter of course. So, we need to take care to maintain ordered submission, otherwise we risk triggering a drive to fall out of sequential-io automation and back to random-io processing, which incurs large latency and degrades throughput. This issue was found in simple benchmarks where QD=2 seq-write performance was 30-50% *greater* than QD=32 seq-write performance. Tagging for -stable and making the change globally since it has a low risk-to-reward ratio. Also, word is that recent versions of an unnamed OS also does it this way now. So, drives in the field are already experienced with this tag ordering scheme. Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ed Ciechanowski <ed.ciechanowski@intel.com> Reviewed-by:
Matthew Wilcox <matthew.r.wilcox@intel.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Rafał Miłecki authored
commit 12cd43c6 upstream. Register B43_MMIO_PSM_PHY_HDR is 16 bit one, so accessing it with 32b functions isn't safe. On my machine it causes delayed (!) CPU exception: Disabling lock debugging due to kernel taint mce: [Hardware Error]: CPU 0: Machine Check Exception: 4 Bank 4: b200000000070f0f mce: [Hardware Error]: TSC 164083803dc mce: [Hardware Error]: PROCESSOR 2:20fc2 TIME 1396650505 SOCKET 0 APIC 0 microcode 0 mce: [Hardware Error]: Run the above through 'mcelog --ascii' mce: [Hardware Error]: Machine check: Processor context corrupt Kernel panic - not syncing: Fatal machine check on current CPU Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Mikulas Patocka authored
commit 43751a1b upstream. This patch fixes the hardware cursor on mach64 when font width is not a multiple of 8 pixels. If you load such a font, the cursor is expanded to the next 8-byte boundary and a part of the next character after the cursor is not visible. For example, when you load a font with 12-pixel width, the cursor width is 16 pixels and when the cursor is displayed, 4 pixels of the next character are not visible. The reason is this: atyfb_cursor is called with proper parameters to load an image that is 12-pixel wide. However, the number is aligned on the next 8-pixel boundary on the line "unsigned int width = (cursor->image.width + 7) >> 3;" and the whole function acts as it is was loading a 16-pixel image. This patch fixes it so that the value written to the framebuffer is padded with 0xaaaa (the transparent pattern) when the image size it not a multiple of 8 pixels. The transparent pattern causes that the cursor will not interfere with the next character. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
Mikulas Patocka authored
commit c29dd869 upstream. This patch fixes mach64 to use unaligned access to the font bitmap. This fixes unaligned access warning on sparc64 when 14x8 font is loaded. On x86(64), unaligned access is handled in hardware, so both functions le32_to_cpup and get_unaligned_le32 perform the same operation. On RISC machines, unaligned access is not handled in hardware, so we better use get_unaligned_le32 to avoid the unaligned trap and warning. Signed-off-by:
-
Mikulas Patocka authored
commit a772d473 upstream. When X11 is running and the user switches back to console, the card modifies the content of registers M_MACCESS and M_PITCH in periodic intervals. This patch fixes it by restoring the content of these registers before issuing any accelerator command. Signed-off-by:
-
Mikulas Patocka authored
commit 00a9d699 upstream. The function cfb_copyarea is buggy when the copy operation is not aligned on long boundary (4 bytes on 32-bit machines, 8 bytes on 64-bit machines). How to reproduce: - use x86-64 machine - use a framebuffer driver without acceleration (for example uvesafb) - set the framebuffer to 8-bit depth (for example fbset -a 1024x768-60 -depth 8) - load a font with character width that is not a multiple of 8 pixels note: the console-tools package cannot load a font that has width different from 8 pixels. You need to install the packages "kbd" and "console-terminus" and use the program "setfont" to set font width (for example: setfont Uni2-Terminus20x10) - move some text left and right on the bash command line and you get a screen corruption To expose more bugs, put this line to the end of uvesafb_init_info: info->flags |= FBINFO_HWACCEL_COPYAREA | FBINFO_READS_FAST; - Now framebuffer console will use cfb_copyarea for console scrolling. You get a screen corruption when console is scrolled. This patch is a rewrite of cfb_copyarea. It fixes the bugs, with this patch, console scrolling in 8-bit depth with a font width that is not a multiple of 8 pixels works fine. The cfb_copyarea code was very buggy and it looks like it was written and never tried with non-8-pixel font. Signed-off-by:
-
Vineet Gupta authored
commit fce16bc3 upstream. In the exception return path, for both U/K cases, intr are already disabled (for various existing reasons). So when we drop down to @restore_regs, we need not redo that. There was subtle issue - when intr were NOT being disabled for ret-to-kernel-but-no-preemption case - now fixed by moving the IRQ_DISABLE further up in @resume_kernel_mode. So what do we gain: * Shaves off a few insn in return path. * Eliminates the need for IRQ_DISABLE_SAVE assembler macro for ARCv2 hence allows for entry code sharing. Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Vineet Gupta authored
commit 147aece2 upstream. Signed-off-by:
-
Martin Schwidefsky authored
commit 6e0de817 upstream. The A register needs to be initialized to zero in the prolog if the first instruction of the BPF program is BPF_S_LDX_B_MSH to prevent leaking the content of %r5 to user space. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Sebastian Ott authored
commit 06cd7a87 upstream. Using a notification type mask for the store event information chsc is unsupported on some firmware levels. Retry SEI with that mask set to zero (which is the old way of requesting only channel subsystem related events). Reported-and-tested-by:
Stefan Haberland <stefan.haberland@de.ibm.com> Reviewed-by:
Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by:
Sebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by:
-
Michael Neuling authored
commit e6b8fd02 upstream. We can't take an IRQ when we're about to do a trechkpt as our GPR state is set to user GPR values. We've hit this when running some IBM Java stress tests in the lab resulting in the following dump: cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40] pc: c000000000050074: restore_gprs+0xc0/0x148 lr: 00000000b52a8184 sp: ac57d360 msr: 8000000100201030 current = 0xc00000002c500000 paca = 0xc000000007dbfc00 softe: 0 irq_happened: 0x00 pid = 34535, comm = Pooled Thread # R00 = 00000000b52a8184 R16 = 00000000b3e48fda R01 = 00000000ac57d360 R17 = 00000000ade79bd8 R02 = 00000000ac586930 R18 = 000000000fac9bcc R03 = 00000000ade60000 R19 = 00000000ac57f930 R04 = 00000000f6624918 R20 = 00000000ade79be8 R05 = 00000000f663f238 R21 = 00000000ac218a54 R06 = 0000000000000002 R22 = 000000000f956280 R07 = 0000000000000008 R23 = 000000000000007e R08 = 000000000000000a R24 = 000000000000000c R09 = 00000000b6e69160 R25 = 00000000b424cf00 R10 = 0000000000000181 R26 = 00000000f66256d4 R11 = 000000000f365ec0 R27 = 00000000b6fdcdd0 R12 = 00000000f66400f0 R28 = 0000000000000001 R13 = 00000000ada71900 R29 = 00000000ade5a300 R14 = 00000000ac2185a8 R30 = 00000000f663f238 R15 = 0000000000000004 R31 = 00000000f6624918 pc = c000000000050074 restore_gprs+0xc0/0x148 cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4 lr = 00000000b52a8184 msr = 8000000100201030 cr = 24804888 ctr = 0000000000000000 xer = 0000000000000000 trap = 700 This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into that function. It then adds IRQ disabling over the trechkpt critical section. It also sets the TEXASR FS in the signals code to ensure this is never set now that we explictly write the TM sprs in tm_recheckpoint. Signed-off-by:
Michael Neuling <mikey@neuling.org> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
-
Anton Blanchard authored
commit 422b9b96 upstream. I noticed this when testing setarch. No, we don't magically support a big endian userspace on a little endian kernel. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Tyler Stachecki authored
commit af61e27c upstream. On suspend, _scsih_suspend calls mpt2sas_base_free_resources, which in turn calls pci_disable_device if the device is enabled prior to suspending. However, _scsih_suspend also calls pci_disable_device itself. Thus, in the event that the device is enabled prior to suspending, pci_disable_device will be called twice. This patch removes the duplicate call to pci_disable_device in _scsi_suspend as it is both unnecessary and results in a kernel oops. Signed-off-by:
Tyler Stachecki <tstache1@binghamton.edu> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Fam Zheng authored
commit 0c8482ac upstream. virtscsi_init calls virtscsi_remove_vqs on err, even before initializing the vqs. The latter calls virtscsi_set_affinity, so let's check the pointer there before setting affinity on it. This fixes a panic when setting device's num_queues=2 on RHEL 6.5: qemu-system-x86_64 ... \ -device virtio-scsi-pci,id=scsi0,addr=0x13,...,num_queues=2 \ -drive file=/stor/vm/dummy.raw,id=drive-scsi-disk,... \ -device scsi-hd,drive=drive-scsi-disk,... [ 0.354734] scsi0 : Virtio SCSI HBA [ 0.379504] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020 [ 0.380141] IP: [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] PGD 0 [ 0.380141] Oops: 0000 [#1] SMP [ 0.380141] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.0+ #5 [ 0.380141] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2007 [ 0.380141] task: ffff88003c9f0000 ti: ffff88003c9f8000 task.ti: ffff88003c9f8000 [ 0.380141] RIP: 0010:[<ffffffff814741ef>] [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] RSP: 0000:ffff88003c9f9c08 EFLAGS: 00010256 [ 0.380141] RAX: 0000000000000000 RBX: ffff88003c3a9d40 RCX: 0000000000001070 [ 0.380141] RDX: 0000000000000002 RSI: 0000000000000000 RDI: 0000000000000000 [ 0.380141] RBP: ffff88003c9f9c28 R08: 00000000000136c0 R09: ffff88003c801c00 [ 0.380141] R10: ffffffff81475229 R11: 0000000000000008 R12: 0000000000000000 [ 0.380141] R13: ffffffff81cc7ca8 R14: ffff88003cac3d40 R15: ffff88003cac37a0 [ 0.380141] FS: 0000000000000000(0000) GS:ffff88003e400000(0000) knlGS:0000000000000000 [ 0.380141] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 0.380141] CR2: 0000000000000020 CR3: 0000000001c0e000 CR4: 00000000000006f0 [ 0.380141] Stack: [ 0.380141] ffff88003c3a9d40 0000000000000000 ffff88003cac3d80 ffff88003cac3d40 [ 0.380141] ffff88003c9f9c48 ffffffff814742e8 ffff88003c26d000 ffff88003c26d000 [ 0.380141] ffff88003c9f9c68 ffffffff81474321 ffff88003c26d000 ffff88003c3a9d40 [ 0.380141] Call Trace: [ 0.380141] [<ffffffff814742e8>] virtscsi_set_affinity+0x28/0x40 [ 0.380141] [<ffffffff81474321>] virtscsi_remove_vqs+0x21/0x50 [ 0.380141] [<ffffffff81475231>] virtscsi_init+0x91/0x240 [ 0.380141] [<ffffffff81365290>] ? vp_get+0x50/0x70 [ 0.380141] [<ffffffff81475544>] virtscsi_probe+0xf4/0x280 [ 0.380141] [<ffffffff81363ea5>] virtio_dev_probe+0xe5/0x140 [ 0.380141] [<ffffffff8144c669>] driver_probe_device+0x89/0x230 [ 0.380141] [<ffffffff8144c8ab>] __driver_attach+0x9b/0xa0 [ 0.380141] [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230 [ 0.380141] [<ffffffff8144c810>] ? driver_probe_device+0x230/0x230 [ 0.380141] [<ffffffff8144ac1c>] bus_for_each_dev+0x8c/0xb0 [ 0.380141] [<ffffffff8144c499>] driver_attach+0x19/0x20 [ 0.380141] [<ffffffff8144bf28>] bus_add_driver+0x198/0x220 [ 0.380141] [<ffffffff8144ce9f>] driver_register+0x5f/0xf0 [ 0.380141] [<ffffffff81d27c91>] ? spi_transport_init+0x79/0x79 [ 0.380141] [<ffffffff8136403b>] register_virtio_driver+0x1b/0x30 [ 0.380141] [<ffffffff81d27d19>] init+0x88/0xd6 [ 0.380141] [<ffffffff81d27c18>] ? scsi_init_procfs+0x5b/0x5b [ 0.380141] [<ffffffff81ce88a7>] do_one_initcall+0x7f/0x10a [ 0.380141] [<ffffffff81ce8aa7>] kernel_init_freeable+0x14a/0x1de [ 0.380141] [<ffffffff81ce8b3b>] ? kernel_init_freeable+0x1de/0x1de [ 0.380141] [<ffffffff817dec20>] ? rest_init+0x80/0x80 [ 0.380141] [<ffffffff817dec29>] kernel_init+0x9/0xf0 [ 0.380141] [<ffffffff817e68fc>] ret_from_fork+0x7c/0xb0 [ 0.380141] [<ffffffff817dec20>] ? rest_init+0x80/0x80 [ 0.380141] RIP [<ffffffff814741ef>] __virtscsi_set_affinity+0x4f/0x120 [ 0.380141] RSP <ffff88003c9f9c08> [ 0.380141] CR2: 0000000000000020 [ 0.380141] ---[ end trace 8074b70c3d5e1d73 ]--- [ 0.475018] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 [ 0.475018] [ 0.475068] Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff) [ 0.475068] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 [jejb: checkpatch fixes] Signed-off-by:
Fam Zheng <famz@redhat.com> Acked-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Rusty Russell authored
commit 1f74ef0f upstream. When adding or removing 100G from a balloon: BUG: soft lockup - CPU#0 stuck for 22s! [vballoon:367] We have a wait_event_interruptible(), but the condition is always true (more ballooning to do) so we don't ever sleep. We also have a wait_event() for the host to ack, but that is also always true as QEMU is synchronous for balloon operations. Reported-by:
Gopesh Kumar Chaudhary <gopchaud@in.ibm.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Huacai Chen authored
commit c14af233 upstream. The original MIPS hibernate code flushes cache and TLB entries in swsusp_arch_resume(). But they are removed in Commit 44eeab67 (MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross- CPU flush is surely unnecessary because all but the local CPU have already been disabled. But a local flush (at least the TLB flush) is needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is very easy to produce a kernel panic (kernel page fault, or unaligned access). The root cause is E1000E driver use vzalloc_node() to allocate pages, the stale TLB entries of the booting kernel will be misused by the resumed target kernel. Signed-off-by:
Huacai Chen <chenhc@lemote.com> Cc: John Crispin <john@phrozen.org> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Cc: Fuxin Zhang <zhangfx@lemote.com> Cc: Zhangjin Wu <wuzhangjin@gmail.com> Patchwork: https://patchwork.linux-mips.org/patch/6643/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
James Hogan authored
commit 15505679 upstream. Previously a reserved instruction exception while in guest code would cause a KVM internal error if kvm_mips_handle_ri() didn't recognise the instruction (including a RDHWR from an unrecognised hardware register). However the guest OS should really have the opportunity to catch the exception so that it can take the appropriate actions such as sending a SIGILL to the guest user process or emulating the instruction itself. Therefore in these cases emulate a guest RI exception and only return EMULATE_FAIL if that fails, being careful to revert the PC first in case the exception occurred in a branch delay slot in which case the PC will already point to the branch target. Also turn the printk messages relating to these cases into kvm_debug messages so that they aren't usually visible. This allows crashme to run in the guest without killing the entire VM. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Gleb Natapov <gleb@kernel.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Sanjay Lal <sanjayl@kymasys.com> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by:
-
Paolo Bonzini authored
commit 5678de3f upstream. QE reported that they got the BUG_ON in ioapic_service to trigger. I cannot reproduce it, but there are two reasons why this could happen. The less likely but also easiest one, is when kvm_irq_delivery_to_apic does not deliver to any APIC and returns -1. Because irqe.shorthand == 0, the kvm_for_each_vcpu loop in that function is never reached. However, you can target the similar loop in kvm_irq_delivery_to_apic_fast; just program a zero logical destination address into the IOAPIC, or an out-of-range physical destination address. Signed-off-by:
-
Sergey Dyasly authored
commit 3159f372 upstream. With LPAE enabled, physical address space is larger than 4GB. Allow mapping any part of it via /dev/mem by using PHYS_MASK to determine valid range. PHYS_MASK covers 40 bits with LPAE enabled and 32 bits otherwise. Reported-by:
Vassili Karpov <av1474@comtv.ru> Signed-off-by:
Sergey Dyasly <dserrg@gmail.com> Acked-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Cc: hujianyang <hujianyang@huawei.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 03e7848a upstream. This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING status require an extra target_put_sess_cmd() in isert_put_cmd() code when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist() context during session shutdown. The extra kref PUT is required so that transport_generic_free_cmd() invokes the last target_put_sess_cmd() -> target_release_cmd_kref(), which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd descriptor with WRITE_PENDING status, and awake the completion in target_wait_for_sess_cmds() to invoke TFO->release_cmd(). The bug was manifesting itself in target_wait_for_sess_cmds() where a se_cmd descriptor with WRITE_PENDING status would end up sleeping indefinately. Acked-by:
Sagi Grimberg <sagig@mellanox.com> Cc: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Matthew Daley authored
commit 2145e15e upstream. Do not leak kernel-only floppy_raw_cmd structure members to userspace. This includes the linked-list pointer and the pointer to the allocated DMA space. Signed-off-by:
Matthew Daley <mattd@bugfuzz.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Matthew Daley authored
commit ef87dbe7 upstream. Always clear out these floppy_raw_cmd struct members after copying the entire structure from userspace so that the in-kernel version is always valid and never left in an interdeterminate state. Signed-off-by:
-
Peter Hurley authored
commit 4291086b upstream. The tty atomic_write_lock does not provide an exclusion guarantee for the tty driver if the termios settings are LECHO & !OPOST. And since it is unexpected and not allowed to call TTY buffer helpers like tty_insert_flip_string concurrently, this may lead to crashes when concurrect writers call pty_write. In that case the following two writers: * the ECHOing from a workqueue and * pty_write from the process race and can overflow the corresponding TTY buffer like follows. If we look into tty_insert_flip_string_fixed_flag, there is: int space = __tty_buffer_request_room(port, goal, flags); struct tty_buffer *tb = port->buf.tail; ... memcpy(char_buf_ptr(tb, tb->used), chars, space); ... tb->used += space; so the race of the two can result in something like this: A B __tty_buffer_request_room __tty_buffer_request_room memcpy(buf(tb->used), ...) tb->used += space; memcpy(buf(tb->used), ...) ->BOOM B's memcpy is past the tty_buffer due to the previous A's tb->used increment. Since the N_TTY line discipline input processing can output concurrently with a tty write, obtain the N_TTY ldisc output_lock to serialize echo output with normal tty writes. This ensures the tty buffer helper tty_insert_flip_string is not called concurrently and everything is fine. Note that this is nicely reproducible by an ordinary user using forkpty and some setup around that (raw termios + ECHO). And it is present in kernels at least after commit d945cb9c (pty: Rework the pty layer to use the normal buffering logic) in 2.6.31-rc3. js: add more info to the commit log js: switch to bool js: lock unconditionally js: lock only the tty->ops->write call References: CVE-2014-0196 Reported-and-tested-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Michael Welling authored
commit b790f210 upstream. The sleep function was updated to put the serial port to sleep only when necessary. This appears to resolve the errant behavior of the driver as described in Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not work with 3.8.0". Signed-off-by:
Michael Welling <mwelling@ieee.org> Signed-off-by:
-
Tomoki Sekiyama authored
commit 501fed45 upstream. When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest, hvc console is setup within a kthread. However, that will cause SEGV and the boot will fail when the driver is builtin to the kernel, because currently hvc_console_setup() is annotated with '__init'. This patch removes '__init' to boot the guest successfully with 'console=hvc0'. Signed-off-by:
Tomoki Sekiyama <tomoki.sekiyama@hds.com> Signed-off-by:
-
- 06 May, 2014 11 commits
-
-
Greg Kroah-Hartman authored
-
Felipe Balbi authored
commit eee3f15d upstream. instead of relying on the otg pointer, which can be NULL in certain cases, we can use the gadget and host pointers we already hold inside struct musb. Tested-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Aaron Sanders authored
commit b16c02fb upstream. Add device ids to pl2303 for the Hewlett-Packard HP POS pole displays: LD960: 03f0:0B39 LCM220: 03f0:3139 LCM960: 03f0:3239 [ Johan: fix indentation and sort PIDs numerically ] Signed-off-by:
Aaron Sanders <aaron.sanders@hp.com> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Theodore Ts'o authored
commit 6e6358fc upstream. We haven't taken i_mutex yet, so we need to use i_size_read(). Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> Signed-off-by:
-
Jan Kara authored
commit ec4cb1aa upstream. When heavily exercising xattr code the assertion that jbd2_journal_dirty_metadata() shouldn't return error was triggered: WARNING: at /srv/autobuild-ceph/gitbuilder.git/build/fs/jbd2/transaction.c:1237 jbd2_journal_dirty_metadata+0x1ba/0x260() CPU: 0 PID: 8877 Comm: ceph-osd Tainted: G W 3.10.0-ceph-00049-g68d04c9 #1 Hardware name: Dell Inc. PowerEdge R410/01V648, BIOS 1.6.3 02/07/2011 ffffffff81a1d3c8 ffff880214469928 ffffffff816311b0 ffff880214469968 ffffffff8103fae0 ffff880214469958 ffff880170a9dc30 ffff8802240fbe80 0000000000000000 ffff88020b366000 ffff8802256e7510 ffff880214469978 Call Trace: [<ffffffff816311b0>] dump_stack+0x19/0x1b [<ffffffff8103fae0>] warn_slowpath_common+0x70/0xa0 [<ffffffff8103fb2a>] warn_slowpath_null+0x1a/0x20 [<ffffffff81267c2a>] jbd2_journal_dirty_metadata+0x1ba/0x260 [<ffffffff81245093>] __ext4_handle_dirty_metadata+0xa3/0x140 [<ffffffff812561f3>] ext4_xattr_release_block+0x103/0x1f0 [<ffffffff81256680>] ext4_xattr_block_set+0x1e0/0x910 [<ffffffff8125795b>] ext4_xattr_set_handle+0x38b/0x4a0 [<ffffffff810a319d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff81257b32>] ext4_xattr_set+0xc2/0x140 [<ffffffff81258547>] ext4_xattr_user_set+0x47/0x50 [<ffffffff811935ce>] generic_setxattr+0x6e/0x90 [<ffffffff81193ecb>] __vfs_setxattr_noperm+0x7b/0x1c0 [<ffffffff811940d4>] vfs_setxattr+0xc4/0xd0 [<ffffffff8119421e>] setxattr+0x13e/0x1e0 [<ffffffff811719c7>] ? __sb_start_write+0xe7/0x1b0 [<ffffffff8118f2e8>] ? mnt_want_write_file+0x28/0x60 [<ffffffff8118c65c>] ? fget_light+0x3c/0x130 [<ffffffff8118f2e8>] ? mnt_want_write_file+0x28/0x60 [<ffffffff8118f1f8>] ? __mnt_want_write+0x58/0x70 [<ffffffff811946be>] SyS_fsetxattr+0xbe/0x100 [<ffffffff816407c2>] system_call_fastpath+0x16/0x1b The reason for the warning is that buffer_head passed into jbd2_journal_dirty_metadata() didn't have journal_head attached. This is caused by the following race of two ext4_xattr_release_block() calls: CPU1 CPU2 ext4_xattr_release_block() ext4_xattr_release_block() lock_buffer(bh); /* False */ if (BHDR(bh)->h_refcount == cpu_to_le32(1)) } else { le32_add_cpu(&BHDR(bh)->h_refcount, -1); unlock_buffer(bh); lock_buffer(bh); /* True */ if (BHDR(bh)->h_refcount == cpu_to_le32(1)) get_bh(bh); ext4_free_blocks() ... jbd2_journal_forget() jbd2_journal_unfile_buffer() -> JH is gone error = ext4_handle_dirty_xattr_block(handle, inode, bh); -> triggers the warning We fix the problem by moving ext4_handle_dirty_xattr_block() under the buffer lock. Sadly this cannot be done in nojournal mode as that function can call sync_dirty_buffer() which would deadlock. Luckily in nojournal mode the race is harmless (we only dirty already freed buffer) and thus for nojournal mode we leave the dirtying outside of the buffer lock. Reported-by:
Sage Weil <sage@inktank.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
alex chen authored
commit f7cf4f5b upstream. Do not put bh when buffer_uptodate failed in ocfs2_write_block and ocfs2_write_super_or_backup, because it will put bh in b_end_io. Otherwise it will hit a warning "VFS: brelse: Trying to free free buffer". Signed-off-by:
Alex Chen <alex.chen@huawei.com> Reviewed-by:
Joseph Qi <joseph.qi@huawei.com> Reviewed-by:
Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.com> Acked-by:
Joel Becker <jlbec@evilplan.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Junxiao Bi authored
commit ded2cf71 upstream. There is a race window in dlm_do_recovery() between dlm_remaster_locks() and dlm_reset_recovery() when the recovery master nearly finish the recovery process for a dead node. After the master sends FINALIZE_RECO message in dlm_remaster_locks(), another node may become the recovery master for another dead node, and then send the BEGIN_RECO message to all the nodes included the old master, in the handler of this message dlm_begin_reco_handler() of old master, dlm->reco.dead_node and dlm->reco.new_master will be set to the second dead node and the new master, then in dlm_reset_recovery(), these two variables will be reset to default value. This will cause new recovery master can not finish the recovery process and hung, at last the whole cluster will hung for recovery. old recovery master: new recovery master: dlm_remaster_locks() become recovery master for another dead node. dlm_send_begin_reco_message() dlm_begin_reco_handler() { if (dlm->reco.state & DLM_RECO_STATE_FINALIZE) { return -EAGAIN; } dlm_set_reco_master(dlm, br->node_idx); dlm_set_reco_dead_node(dlm, br->dead_node); } dlm_reset_recovery() { dlm_set_reco_dead_node(dlm, O2NM_INVALID_NODE_NUM); dlm_set_reco_master(dlm, O2NM_INVALID_NODE_NUM); } will hang in dlm_remaster_locks() for request dlm locks info Before send FINALIZE_RECO message, recovery master should set DLM_RECO_STATE_FINALIZE for itself and clear it after the recovery done, this can break the race windows as the BEGIN_RECO messages will not be handled before DLM_RECO_STATE_FINALIZE flag is cleared. A similar race may happen between new recovery master and normal node which is in dlm_finalize_reco_handler(), also fix it. Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Wengang Wang <wen.gang.wang@oracle.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Signed-off-by:
-
Junxiao Bi authored
commit 34aa8dac upstream. This issue was introduced by commit 800deef3 ("ocfs2: use list_for_each_entry where benefical") in 2007 where it replaced list_for_each with list_for_each_entry. The variable "lock" will point to invalid data if "tmpq" list is empty and a panic will be triggered due to this. Sunil advised reverting it back, but the old version was also not right. At the end of the outer for loop, that list_for_each_entry will also set "lock" to an invalid data, then in the next loop, if the "tmpq" list is empty, "lock" will be an stale invalid data and cause the panic. So reverting the list_for_each back and reset "lock" to NULL to fix this issue. Another concern is that this seemes can not happen because the "tmpq" list should not be empty. Let me describe how. old lock resource owner(node 1): migratation target(node 2): image there's lockres with a EX lock from node 2 in granted list, a NR lock from node x with convert_type EX in converting list. dlm_empty_lockres() { dlm_pick_migration_target() { pick node 2 as target as its lock is the first one in granted list. } dlm_migrate_lockres() { dlm_mark_lockres_migrating() { res->state |= DLM_LOCK_RES_BLOCK_DIRTY; wait_event(dlm->ast_wq, !dlm_lockres_is_dirty(dlm, res)); //after the above code, we can not dirty lockres any more, // so dlm_thread shuffle list will not run downconvert lock from EX to NR upconvert lock from NR to EX <<< migration may schedule out here, then <<< node 2 send down convert request to convert type from EX to <<< NR, then send up convert request to convert type from NR to <<< EX, at this time, lockres granted list is empty, and two locks <<< in the converting list, node x up convert lock followed by <<< node 2 up convert lock. // will set lockres RES_MIGRATING flag, the following // lock/unlock can not run dlm_lockres_release_ast(dlm, res); } dlm_send_one_lockres() dlm_process_recovery_data() for (i=0; i<mres->num_locks; i++) if (ml->node == dlm->node_num) for (j = DLM_GRANTED_LIST; j <= DLM_BLOCKED_LIST; j++) { list_for_each_entry(lock, tmpq, list) if (lock) break; <<< lock is invalid as grant list is empty. } if (lock->ml.node != ml->node) BUG() >>> crash here } I see the above locks status from a vmcore of our internal bug. Signed-off-by:
-
Liu Hua authored
commit 80df2847 upstream. As sysctl_hung_task_timeout_sec is unsigned long, when this value is larger then LONG_MAX/HZ, the function schedule_timeout_interruptible in watchdog will return immediately without sleep and with print : schedule_timeout: wrong timeout value ffffffffffffff83 and then the funtion watchdog will call schedule_timeout_interruptible again and again. The screen will be filled with "schedule_timeout: wrong timeout value ffffffffffffff83" This patch does some check and correction in sysctl, to let the function schedule_timeout_interruptible allways get the valid parameter. Signed-off-by:
Liu Hua <sdu.liu@huawei.com> Tested-by:
Satoru Takeuchi <satoru.takeuchi@gmail.com> Signed-off-by:
-
Mizuma, Masayoshi authored
commit 55f67141 upstream. When I decrease the value of nr_hugepage in procfs a lot, softlockup happens. It is because there is no chance of context switch during this process. On the other hand, when I allocate a large number of hugepages, there is some chance of context switch. Hence softlockup doesn't happen during this process. So it's necessary to add the context switch in the freeing process as same as allocating process to avoid softlockup. When I freed 12 TB hugapages with kernel-2.6.32-358.el6, the freeing process occupied a CPU over 150 seconds and following softlockup message appeared twice or more. $ echo 6000000 > /proc/sys/vm/nr_hugepages $ cat /proc/sys/vm/nr_hugepages 6000000 $ grep ^Huge /proc/meminfo HugePages_Total: 6000000 HugePages_Free: 6000000 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB $ echo 0 > /proc/sys/vm/nr_hugepages BUG: soft lockup - CPU#16 stuck for 67s! [sh:12883] ... Pid: 12883, comm: sh Not tainted 2.6.32-358.el6.x86_64 #1 Call Trace: free_pool_huge_page+0xb8/0xd0 set_max_huge_pages+0x128/0x190 hugetlb_sysctl_handler_common+0x113/0x140 hugetlb_sysctl_handler+0x1e/0x20 proc_sys_call_handler+0x97/0xd0 proc_sys_write+0x14/0x20 vfs_write+0xb8/0x1a0 sys_write+0x51/0x90 __audit_syscall_exit+0x265/0x290 system_call_fastpath+0x16/0x1b I have not confirmed this problem with upstream kernels because I am not able to prepare the machine equipped with 12TB memory now. However I confirmed that the amount of decreasing hugepages was directly proportional to the amount of required time. I measured required times on a smaller machine. It showed 130-145 hugepages decreased in a millisecond. Amount of decreasing Required time Decreasing rate hugepages (msec) (pages/msec) ------------------------------------------------------------ 10,000 pages == 20GB 70 - 74 135-142 30,000 pages == 60GB 208 - 229 131-144 It means decrement of 6TB hugepages will trigger softlockup with the default threshold 20sec, in this decreasing rate. Signed-off-by:
Masayoshi Mizuma <m.mizuma@jp.fujitsu.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Michal Hocko <mhocko@suse.cz> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by:
-
Vlastimil Babka authored
commit 57e68e9c upstream. A BUG_ON(!PageLocked) was triggered in mlock_vma_page() by Sasha Levin fuzzing with trinity. The call site try_to_unmap_cluster() does not lock the pages other than its check_page parameter (which is already locked). The BUG_ON in mlock_vma_page() is not documented and its purpose is somewhat unclear, but apparently it serializes against page migration, which could otherwise fail to transfer the PG_mlocked flag. This would not be fatal, as the page would be eventually encountered again, but NR_MLOCK accounting would become distorted nevertheless. This patch adds a comment to the BUG_ON in mlock_vma_page() and munlock_vma_page() to that effect. The call site try_to_unmap_cluster() is fixed so that for page != check_page, trylock_page() is attempted (to avoid possible deadlocks as we already have check_page locked) and mlock_vma_page() is performed only upon success. If the page lock cannot be obtained, the page is left without PG_mlocked, which is again not a problem in the whole unevictable memory design. Signed-off-by:
Vlastimil Babka <vbabka@suse.cz> Signed-off-by:
Bob Liu <bob.liu@oracle.com> Reported-by:
Sasha Levin <sasha.levin@oracle.com> Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com> Cc: Michel Lespinasse <walken@google.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Acked-by:
Rik van Riel <riel@redhat.com> Cc: David Rientjes <rientjes@google.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Hugh Dickins <hughd@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Signed-off-by:
-
