Fix warnings due to incorrect rst markup. Also improved the presentation
a little without changing the underlying content.
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Link: https://lore.kernel.org/r/20191122034702.58563-1-dwlsalmeida@gmail.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The recommended function is called gpiod_count(), not gpiod_get_count().

Fixes: f626d6df ("gpio: of: Break out OF-only code")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191120154521.16273-1-geert+renesas@glider.beSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191120143745.1254-1-geert+renesas@glider.beSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

When commit 75e99bf5 ("gpio: lynxpoint: set default handler to be
handle_bad_irq()") switched default handler to be handle_bad_irq() the
lp_irq_type() function remained untouched. It means that even request_irq()
can't change the handler and we are not able to handle IRQs properly anymore.
Fix it by setting correct handlers in the lp_irq_type() callback.

Fixes: 75e99bf5 ("gpio: lynxpoint: set default handler to be handle_bad_irq()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191118180251.31439-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

For the repositories we keep on git.kernel.org replace my email
to be on the same domain for sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191118134926.37337-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

acpi_gpiochip_alloc_event is used to loop over all _AEI resources, if
we fail to bind an event handler to one of them, that is not a reason to
not try the other resources.

This commit modifies acpi_gpiochip_alloc_event to always return AE_OK,
so that we will always try to add an event handler for all _AEI resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191114102600.34558-2-hdegoede@redhat.comAcked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Qoriq requires the IBE register to be set to enable GPIO inputs to be
read.  Set it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1iX3HC-00069N-0T@rmk-PC.armlinux.org.ukSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.

The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:

- fsl,mpc8572-gpio
- fsl,ls1028a-gpio
- fsl,ls1088a-gpio

On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).

Fixes: 82e39b0d ("gpio: mpc8xxx: handle differences between incarnations at a single place")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.comTested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Print pin number and error-code on acpi_gpiochip_alloc_event errors,
to help debugging these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191114102600.34558-1-hdegoede@redhat.comAcked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There should be spaces between logical operators and their operands.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'intel-gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel

intel-gpio for v5.5-1

* Prerequisite patch against GPIO library to register pin ranges in time.
* Second attempt to fix Intel Merrifield GPIO driver to utilize irqchip.

The following is an automated git shortlog grouped by driver:

gpiolib:
 -  Introduce ->add_pin_ranges() callback

merrifield:
 -  Pass irqchip when adding gpiochip
 -  Add GPIO <-> pin mapping ranges via callback

Merge tag 'gpio-v5.5-updates-for-linus-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel

gpio: updates for v5.5

- add MODULE_ALIAS() for bd70528 (makes it possible to autoload the
  module from user-space)
- use proper irc_chip names in gpio-em and gpio-rcar
- expose the line bias settings to user-space in the form of new request
  flags
- expose a new ioctl() to user-space which allows to change certain
  proprties of requested lines without releasing them first
- various updates for gpio-tegra186: debounce support, code
  simplification and interrupt routing
- use platform_get_irq() in gpio-em for some code shrinkage
- remove leftovers after recent gpio-mmio changes

Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use
the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but
works with arbitrary firmware node.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.

For chained irqchips this is a pretty straight-forward conversion.

Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>

When IRQ chip is instantiated via GPIO library flow, the few functions,
in particular the ACPI event registration mechanism, on some of ACPI based
platforms expect that the pin ranges are initialized to that point.

Add GPIO <-> pin mapping ranges via callback in the GPIO library flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

When IRQ chip is being added by GPIO library, the ACPI based platform expects
GPIO <-> pin mapping ranges to be initialized in order to correctly initialize
ACPI event mechanism on affected platforms. Unfortunately this step is missed.

Introduce ->add_pin_ranges() callback to fill the above mentioned gap.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>

The comment should have been removed when new GPIO direction
definitions were taken in use as the function logic was changed. It
is now perfectly valid and Ok to hit the return from the bottom of
the direction getting function.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Use the platform_get_irq() helper instead of handling resources
directly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The GPIO controller found on Tegra186 and later supports debouncing for
inputs for up to 255 ms.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The controls for the GG port on Tegra194 resides in the power partition
of the C5 PCIe controller and its interrupt route mapping can therefore
not be programmed by early boot firmware along with that of the other
ports.

Detect this generically by looking at which controls have already been
locked down using the security registers and fill in default values for
controls that are unlocked.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The register offsets for a given bank and port can be easily derived
from the bank and port indices. Update the port descriptors to list only
the bank and port numbers to simplify this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add the GPIOHANDLE_SET_CONFIG_IOCTL to the gpio chardev.
The ioctl allows some of the configuration of a requested handle to be
changed without having to release the line.
The primary use case is the changing of direction for bi-directional
lines.

Based on initial work by Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Move validation of line handle flags into helper function.
This reduces the size and complexity of linehandle_create and allows the
validation to be reused elsewhere.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add support for the pull up/down state set via gpiolib line requests to
be reflected in the state of the mockup.
Use case is for testing of the GPIO uAPI, specifically the pull up/down
flags.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Allow pull up/down bias to be set on output lines.
Use case is for open source or open drain applications where
internal pull up/down may conflict with external biasing.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Allow pull up/down bias to be disabled, allowing the line to float
or to be biased only by external circuitry.
Use case is for where the bias has been applied previously, either
by default or by the user, but that setting may conflict with the
current use of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add support for pull up/down to lineevent_create.
Use cases include receiving asynchronous presses from a
push button without an external pull up/down.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

Add pull-up/pull-down flags to the gpio line get and
set ioctl() calls.  Use cases include a push button
that does not have an external resistor.

Addition use cases described by Limor Fried (ladyada) of
Adafruit in this PR for Adafruit_Blinka Python lib:
https://github.com/adafruit/Adafruit_Blinka/pull/59Signed-off-by: Drew Fustini <drew@pdp7.com>
[Kent: added BIAS to GPIO flag names and restrict application to input
lines]
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

The bd70528 GPIO driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell
for GPIO is added.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>

"ser_device.state" is "unsigned long", i.e. 32-bit or 64-bit, depending
on the platform.  Hence casting its address to "u32 *", and calling
debugfs_create_x32() breaks operation on 64-bit platforms.

Fix this by using the new debugfs_create_xul() helper instead.

Fixes: 9b27105b ("net-caif-driver: add CAIF serial driver (ldisc)")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191025094130.26033-4-geert+renesas@glider.beSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the new debugfs_create_xul() helper instead of open-coding the same
operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/20191025094130.26033-3-geert+renesas@glider.beSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When calling debugfs functions, there is no need to ever check the
return value.  The function can work or not, but the code logic should
never do something different based on this.

Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-media@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20191107085238.GA1285658@kroah.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit 8c550e94.

This was prematurely applied and we need to back it out to merge
a better version of the development track for this feature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Linux 5.4-rc6