Configuration parameters return number of CID each chute supports. The WRB_Q
is created for the passed CID count. If both the Chute has iSCSI Protocol then
WRB_Q creation is in a round robin mechanism.

For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Initialization of SGL and related PAGE posting is to be done for the chute.
Based on configuration value of each Chute,SGL initialization and page posting
is done.

For BE-X family iSCSI protocol is loaded only on single chute
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Template HDR is created for each chute which has iSCSI Protocol loaded.
For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

DEF_Q[HDR/DATA] is created on the chute on which iSCSI Protocol is loaded.
When a connection is offloaded, the DEF_Q HDR/Data ID needs to be passed.
FW posts ASYNC message received from target on the passed DEF_Q. Connection
can be offloaded on any of the chute so DEF_Q is created on each Chute.

Change in the ASYNC path initialization based on the configuration parameters
returned for each chute.

For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

On the adapter iSCSI protocol can be loaded on either one or both
the CHUTE.Check on which CHUTE iSCSI Protocol is loaded and get
configuration parameters based on which driver initization is done.

For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The timeout set in MBX_CMD is 100sec and the ready bit checking in BMBX
mode is done for 4sec. After 4sec the task is scheduled out for 5 secs
to avoid kernel soft lockup stack trace. The loop of 4sec ready bit check
and then schedule out is done until the following conditon occur
- The Ready Bit is Set
- The timeout set in MBX_CMD expires
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The default pdu is a common resource and needs to be protected
while manipulating it.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

- Removed the check of MaxXmitDSL == 0 as this is not a possible
  case.
- Update connection offload data structure for SKH-R adapters.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Storing MAC ADDR of each function in it's priv structure to
avoid issuing MAC_ADDR get IOCTL. Based on a flag set/unset
it's decided if MAC_ADDR is stored in priv structure or IOCTL
needs to be issued.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

When MBX CMD is posted in MCCQ and if command times out,during
mccq resource cleanup for the timed out command  mccq->count
was not decremented. The led to BUG_ON being hit.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Allocating memory in the Host which will be used by the
TOE functionality during Session Offload. This fix will
allow performance improvement as adapter memory contention
will be reduced.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

[v2] - removed the interface->enabled flag setting which prevented the
       fcoe ctlr link from being brought back up after a MTU change

A rtnl_lock deadlock was observed from the rmmod thread where it
tries to unregister the fcoe_ctlr device.  This unregistration
triggered a flush of the sysfs queue of the associated ctlr and led to
a call to the set_fcoe_ctlr_enabled routine.  This will eventually propagate
down to call the bnx2fc_disable routine and contented for the rtnl_lock
in the same context.

This patch creates a subset of the bnx2fc_enable/disable routine which
removes the unnecesary rtnl_lock and the bnx2fc_dev_lock acquisition from
the set_fcoe_ctlr_enabled path.

 kernel: INFO: task rmmod:7874 blocked for more than 120 seconds.
 kernel:      Tainted: G        W  ---------------    2.6.32-415.0.1.el6.x86_64 #1
 kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
 kernel: rmmod         D 000000000000000f     0  7874   6518 0x00000080
 kernel: ffff88022158f7d8 0000000000000086 0000000000000000 0000000000000000
 kernel: ffff88023fe72600 ffff88043c74d410 ffff88043c74d400 ffff88043c74d000
 kernel: ffff88021ecbe5f8 ffff88022158ffd8 000000000000fbc8 ffff88021ecbe5f8
 kernel: Call Trace:
 kernel: [<ffffffff81525985>] schedule_timeout+0x215/0x2e0
 kernel: [<ffffffff810680c0>] ? pick_next_task_fair+0xd0/0x130
 kernel: [<ffffffff81524858>] ? schedule+0x178/0x3b2
 kernel: [<ffffffff81525603>] wait_for_common+0x123/0x180
 kernel: [<ffffffff81066b40>] ? default_wake_function+0x0/0x20
 kernel: [<ffffffff811a486e>] ? ifind_fast+0x5e/0xb0
 kernel: [<ffffffff8152571d>] wait_for_completion+0x1d/0x20
 kernel: [<ffffffff81203868>] sysfs_addrm_finish+0x228/0x270
 kernel: [<ffffffff812014ab>] sysfs_hash_and_remove+0x5b/0x90
 kernel: [<ffffffff812056af>] sysfs_remove_group+0x5f/0x100
 kernel: [<ffffffff81367e8b>] device_remove_groups+0x3b/0x60
 kernel: [<ffffffff8136811d>] device_remove_attrs+0x3d/0x90
 kernel: [<ffffffff81368295>] device_del+0x125/0x1e0
 kernel: [<ffffffff81368372>] device_unregister+0x22/0x60
 kernel: [<ffffffffa038ead2>] fcoe_ctlr_device_delete+0xe2/0xf4 [libfcoe]
 kernel: [<ffffffffa03c43cb>] bnx2fc_interface_release+0x5b/0x90 [bnx2fc]
 kernel: [<ffffffffa03c4370>] ? bnx2fc_interface_release+0x0/0x90 [bnx2fc]
 kernel: [<ffffffff812835e7>] kref_put+0x37/0x70
 kernel: [<ffffffffa03c4192>] __bnx2fc_destroy+0x72/0xa0 [bnx2fc]
 kernel: [<ffffffffa03c5265>] bnx2fc_ulp_exit+0xf5/0x160 [bnx2fc]    <- got bnx2fc_dev_lock mutex_lock
 kernel: [<ffffffffa03b03c6>] cnic_ulp_exit+0xb6/0xc0 [cnic]
 kernel: [<ffffffffa03b5418>] cnic_netdev_event+0x368/0x370 [cnic]
 kernel: [<ffffffffa038c56c>] ? fcoe_del_netdev_mapping+0x8c/0xa0 [libfcoe]
 kernel: [<ffffffff8152a6e5>] notifier_call_chain+0x55/0x80
 kernel: [<ffffffff810a0a46>] raw_notifier_call_chain+0x16/0x20
 kernel: [<ffffffff81459beb>] call_netdevice_notifiers+0x1b/0x20
 kernel: [<ffffffff8145ab34>] rollback_registered_many+0x154/0x280
 kernel: [<ffffffff8145ad08>] rollback_registered+0x38/0x50
 kernel: [<ffffffff8145ad78>] unregister_netdevice_queue+0x58/0xa0
 kernel: [<ffffffff8145add0>] unregister_netdevice+0x10/0x20
 kernel: [<ffffffff8145adfe>] unregister_netdev+0x1e/0x30                  <- got rtnl_lock!!!!!!!!!
 kernel: [<ffffffffa0122278>] __bnx2x_remove+0x48/0x270 [bnx2x] <- got & rel rtnl_lock
 kernel: [<ffffffffa0122554>] bnx2x_remove_one+0x44/0x80 [bnx2x]
 kernel: [<ffffffff812a3af7>] pci_device_remove+0x37/0x70
 kernel: [<ffffffff8136b2ef>] __device_release_driver+0x6f/0xe0
 kernel: [<ffffffff8136b428>] driver_detach+0xc8/0xd0
 kernel: [<ffffffff8136a22e>] bus_remove_driver+0x8e/0x110
 kernel: [<ffffffff8136bc12>] driver_unregister+0x62/0xa0
 kernel: [<ffffffff812a3e04>] pci_unregister_driver+0x44/0xb0
 kernel: [<ffffffffa0191954>] bnx2x_cleanup+0x18/0x73 [bnx2x]
 kernel: [<ffffffff810b8be4>] sys_delete_module+0x194/0x260
 kernel: [<ffffffff810e1347>] ? audit_syscall_entry+0x1d7/0x200
 kernel: [<ffffffff8100b072>] system_call_fastpath+0x16/0x1b
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

In the case when a SCSI_CMD times out, bnx2fc will initiate the sending of the
ABTS.  However, if the SCSI layer's SCSI command timer also times out, it'll
instantiate a task abort of the same xid.

The race condition this patch tries to fix is as follows:

SCSI_CMD timeout (20s)
thread 1                   thread 2
send ABTS
rx ABTS cmpl
                           task abort_eh
                           explicit LOGO since ABTS was engaged
                           CLEANUP cmpl
SCSI_CMD cmpl (ABTS cmpl)
instantiate RRQ
wait 10s
attempt to send RRQ (because of LOGO, it wouldn't continue)

Note that there is no call to scsi_done for this SCSI_CMD cmpletion
in this path.

The patch changes the path of execution to call scsi_done immediately
instead of instantiating the RRQ.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Add support to get local CHAP - index, username and password,
sysfs params of iscsi session corresponding to flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Provide support to add/update the CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

For offload iSCSI like qla4xxx, CHAP entries are stored in adapter's
flash.
This patch adds support to add/update CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

To write a CHAP entry in adapter's flash calculate the offset based
on the type of adapter.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If any flash target entry is using CHAP authentication then set
CHAP username and password sysfs params for the corresponding
iscsi sessions.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Support setting of CHAP_OUT_IDX param for the target entry in flash.
Setting of valid local CHAP index with enable CHAP AUTH for that
flash target entry and disabling CHAP AUTH will invalidate the CHAP
index for the flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Earlier logic for driver created iscsi_session->discovery_parent_idx
was to store ram index of a sendtarget entry, but driver frees
sendtarget ram index as soon as firmware is done with discovery,
which is available for further use. So changing the logic to point
iscsi_session->discovery_parent_idx to store sendtarget flashnode index.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixed two issues in this patch-
1) In function megasas_get_pd_list(), data read(pd_addr->deviceId) from DMAed memory is converted to CPU's endianess.
2) While register AEN, removed some endianness conversion on some fields, since their endianess is already converted.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Added check for DMA mapping errors for request sense data
buffer. Checking for mapping error can avoid potential wild
writes. This patch was prompted by the warning from
dma_unmap when kernel is compiled with CONFIG_DMA_API_DEBUG.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This feature gathers active and cumulative per fnic stats for io,
abort, terminate, reset, vlan discovery path and it also includes
various important stats for debugging issues. It also provided
debugfs and ioctl interface for user to retrieve these stats.
It also provides functionality to reset cumulative stats through
user interface.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixed appropriate error codes that returns negative error number on failure,
and 0 on success. fnic_reset() is used directly by the fc transport callback
issue_fc_host_lip which requires a negative error number on failure.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If you mutiple devices connect to a host, we might be interested in
have an intensive I/O workload on one disk, and notice starvation on others.
This give the user more hint about current infight io for scsi device.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Sean Stewart <Sean.Stewart@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The PCIE capability offset is saved during PCI bus walking.  It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it.  Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch removes the PCI ID of a cancelled Smart Array.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:

"
sd_probe_async() ->
	add_disk() ->
		disk_add_event() ->
			schedule(disk_events_workfn)
	sd_revalidate_disk()
	blk_pm_runtime_init()
return;

Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.

So the race condition is -

Thread 1 			  |		Thread 2
sd_revalidate_disk()		  |	sd_check_events()
...nr_pending = 0 as q->dev = NULL|	scsi_queue_insert()
blk_runtime_pm_init()		  | 	blk_pm_requeue_request() ->
				  |	nr_pending = -1 since
				  |	q->dev != NULL
"

The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.

Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.

If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This fixes an oops caused by buslogic driver when initializing a BusLogic
MultiMaster adapter. Initialization code used scope of a variable
incorrectly which created a NULL pointer. Oops message is below:

BUG: unable to handle kernel NULL pointer dereference at 0000000c
IP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583
*pde = 00000000
Oops: 002 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.11.1.puz1 #1
Hardware name:    /Canterwood, BIOS 6.00 PG 05/16/2003
task: f7050000 ti: f7054000 task.ti: f7054000
EIP: 0060:[<c150c137>] EFLAGS: 00010246 CPU:1
EIP is at blogic_init_mm_probeinfo.isra.17+0x20a/0x583
EAX: 00000013 EBX: 00000000 ECX: 00000000 EDX: f8001000
ESI: f71cb800 EDI: f7388000 EBP: 00007800 ESP: f7055c84
 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: 0000000c CR3: 0154f000 CR4: 000007d0
Stack:
 0000001c 00000000 c11a59f6 f7055c98 00008130 ffffffff ffffffff 00000000
 00000003 00000000 00000000 00000000 00000013 f8001000 00000001 000003d0
 00000000 00000000 00000000 c14e3f84 f78803c8 00000000 f738c000 000000e9
Call Trace:
 [<c11a59f6>] ? pci_get_subsys+0x33/0x38
 [<c150c4fb>] ? blogic_init_probeinfo_list+0x4b/0x19e
 [<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
 [<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
 [<c10fb99e>] ? sysfs_link_sibling+0x61/0x8d
 [<c10b0519>] ? kmem_cache_alloc+0x8b/0xb5
 [<c150cce5>] ? blogic_init+0xa1/0x10e8
 [<c10fc0a8>] ? sysfs_add_one+0x10/0x9d
 [<c10fc18a>] ? sysfs_addrm_finish+0x12/0x85
 [<c10fca37>] ? sysfs_do_create_link_sd+0x9d/0x1b4
 [<c117c272>] ? blk_register_queue+0x69/0xb3
 [<c10fcb68>] ? sysfs_create_link+0x1a/0x2c
 [<c1181a07>] ? add_disk+0x1a1/0x3c7
 [<c138737b>] ? klist_next+0x60/0xc3
 [<c122cc3a>] ? scsi_dh_detach+0x68/0x68
 [<c1213e36>] ? bus_for_each_dev+0x51/0x61
 [<c1000356>] ? do_one_initcall+0x22/0x12c
 [<c10f3688>] ? __proc_create+0x8c/0xba
 [<c150cc44>] ? blogic_setup+0x5f6/0x5f6
 [<c14e94aa>] ? repair_env_string+0xf/0x4d
 [<c14e949b>] ? do_early_param+0x71/0x71
 [<c103efaa>] ? parse_args+0x21f/0x33d
 [<c14e9a54>] ? kernel_init_freeable+0xdf/0x17d
 [<c14e949b>] ? do_early_param+0x71/0x71
 [<c1388b64>] ? kernel_init+0x8/0xc0
 [<c1392222>] ? ret_from_kernel_thread+0x6/0x28
 [<c1392227>] ? ret_from_kernel_thread+0x1b/0x28
 [<c1388b5c>] ? rest_init+0x6c/0x6c
Code: 89 44 24 10 0f b6 44 24 3d 89 44 24 0c c7 44 24 08 00 00 00 00 c7 44 24 04 38 62 46 c1 c7 04 24 02 00 00 00 e8 78 13 d2 ff 31 db <89> 6b 0c b0 20 89 ea ee
 c7 44 24 08 04 00 00 00 8d 44 24 4c 89
EIP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583 SS:ESP 0068:f7055c84
CR2: 000000000000000c
---[ end trace 17f45f5196d40487 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: <stable@vger.kernel.org> # 3.11.x
Reported-by: Pierre Uszynski <pierre@rahul.net>
Tested-by: Pierre Uszynski <pierre@rahul.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a deadlock on the ts72xx_wdt driver, fix bitmasks in the
  kempld_wdt driver and fix a section mismatch in the sunxi_wdt driver"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sunxi: Fix section mismatch
  watchdog: kempld_wdt: Fix bit mask definition
  watchdog: ts72xx_wdt: locking bug in ioctl

This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.

WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>