- 03 Apr, 2019 13 commits
-
-
Xin Long authored
[ Upstream commit 273160ff ] sctp_hdr(skb) only works when skb->transport_header is set properly. But in Netfilter, skb->transport_header for ipv6 is not guaranteed to be right value for sctphdr. It would cause to fail to check the checksum for sctp packets. So fix it by using offset, which is always right in all places. v1->v2: - Fix the changelog. Fixes: e6d8b64b ("net: sctp: fix and consolidate SCTP checksumming code") Reported-by:
Li Shuang <shuali@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Zhiqiang Liu authored
[ Upstream commit cc4807bb ] Commit ad6c9986 ("vxlan: Fix GRO cells race condition between receive and link delete") fixed a race condition for the typical case a vxlan device is dismantled from the current netns. But if a netns is dismantled, vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue() of all the vxlan tunnels that are related to this netns. In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before unregister_netdevice_queue(). This means that the gro_cells_destroy() call is done too soon, for the same reasons explained in above commit. So we need to fully respect the RCU rules, and thus must remove the gro_cells_destroy() call or risk use after-free. Fixes: 58ce31cc ("vxlan: GRO support at tunnel layer") Signed-off-by:
Suanming.Mou <mousuanming@huawei.com> Suggested-by:
Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Reviewed-by:
Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 89e41309 ] When a dual stack tcp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or tcp_v6_iif() helper. Fixes: 1397ed35 ("ipv6: add flowinfo for tcp6 pkt_options for all cases") Fixes: df3687ff ("ipv6: add the IPV6_FL_F_REFLECT flag to IPV6_FL_A_GET") Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Maxime Chevallier authored
[ Upstream commit a4dc6a49 ] When using fanouts with AF_PACKET, the demux functions such as fanout_demux_cpu will return an index in the fanout socket array, which corresponds to the selected socket. The ordering of this array depends on the order the sockets were added to a given fanout group, so for FANOUT_CPU this means sockets are bound to cpus in the order they are configured, which is OK. However, when stopping then restarting the interface these sockets are bound to, the sockets are reassigned to the fanout group in the reverse order, due to the fact that they were inserted at the head of the interface's AF_PACKET socket list. This means that traffic that was directed to the first socket in the fanout group is now directed to the last one after an interface restart. In the case of FANOUT_CPU, traffic from CPU0 will be directed to the socket that used to receive traffic from the last CPU after an interface restart. This commit introduces a helper to add a socket at the tail of a list, then uses it to register AF_PACKET sockets. Note that this changes the order in which sockets are listed in /proc and with sock_diag. Fixes: dc99f600 ("packet: Add fanout support") Signed-off-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e5dcc0c3 ] rose_write_internal() uses a temp buffer of 100 bytes, but a manual inspection showed that given arbitrary input, rose_create_facilities() can fill up to 110 bytes. Lets use a tailroom of 256 bytes for peace of mind, and remove the bounce buffer : we can simply allocate a big enough skb and adjust its length as needed. syzbot report : BUG: KASAN: stack-out-of-bounds in memcpy include/linux/string.h:352 [inline] BUG: KASAN: stack-out-of-bounds in rose_create_facilities net/rose/rose_subr.c:521 [inline] BUG: KASAN: stack-out-of-bounds in rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116 Write of size 7 at addr ffff88808b1ffbef by task syz-executor.0/24854 CPU: 0 PID: 24854 Comm: syz-executor.0 Not tainted 5.0.0+ #97 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x172/0x1f0 lib/dump_stack.c:113 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317 check_memory_region_inline mm/kasan/generic.c:185 [inline] check_memory_region+0x123/0x190 mm/kasan/generic.c:191 memcpy+0x38/0x50 mm/kasan/common.c:131 memcpy include/linux/string.h:352 [inline] rose_create_facilities net/rose/rose_subr.c:521 [inline] rose_write_internal+0x597/0x15d0 net/rose/rose_subr.c:116 rose_connect+0x7cb/0x1510 net/rose/af_rose.c:826 __sys_connect+0x266/0x330 net/socket.c:1685 __do_sys_connect net/socket.c:1696 [inline] __se_sys_connect net/socket.c:1693 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1693 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x458079 Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f47b8d9dc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002a RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000458079 RDX: 000000000000001c RSI: 0000000020000040 RDI: 0000000000000004 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f47b8d9e6d4 R13: 00000000004be4a4 R14: 00000000004ceca8 R15: 00000000ffffffff The buggy address belongs to the page: page:ffffea00022c7fc0 count:0 mapcount:0 mapping:0000000000000000 index:0x0 flags: 0x1fffc0000000000() raw: 01fffc0000000000 0000000000000000 ffffffff022c0101 0000000000000000 raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff88808b1ffa80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffb00: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 00 00 00 03 >ffff88808b1ffb80: f2 f2 00 00 00 00 00 00 00 00 00 00 00 00 04 f3 ^ ffff88808b1ffc00: f3 f3 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00 ffff88808b1ffc80: 00 00 00 00 00 00 00 f1 f1 f1 f1 f1 f1 01 f2 01 Signed-off-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Christoph Paasch authored
[ Upstream commit 398f0132 ] Since commit fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") one can now allocate packet ring buffers >= UINT_MAX. However, syzkaller found that that triggers a warning: [ 21.100000] WARNING: CPU: 2 PID: 2075 at mm/page_alloc.c:4584 __alloc_pages_nod0 [ 21.101490] Modules linked in: [ 21.101921] CPU: 2 PID: 2075 Comm: syz-executor.0 Not tainted 5.0.0 #146 [ 21.102784] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 0.5.1 01/01/2011 [ 21.103887] RIP: 0010:__alloc_pages_nodemask+0x2a0/0x630 [ 21.104640] Code: fe ff ff 65 48 8b 04 25 c0 de 01 00 48 05 90 0f 00 00 41 bd 01 00 00 00 48 89 44 24 48 e9 9c fe 3 [ 21.107121] RSP: 0018:ffff88805e1cf920 EFLAGS: 00010246 [ 21.107819] RAX: 0000000000000000 RBX: ffffffff85a488a0 RCX: 0000000000000000 [ 21.108753] RDX: 0000000000000000 RSI: dffffc0000000000 RDI: 0000000000000000 [ 21.109699] RBP: 1ffff1100bc39f28 R08: ffffed100bcefb67 R09: ffffed100bcefb67 [ 21.110646] R10: 0000000000000001 R11: ffffed100bcefb66 R12: 000000000000000d [ 21.111623] R13: 0000000000000000 R14: ffff88805e77d888 R15: 000000000000000d [ 21.112552] FS: 00007f7c7de05700(0000) GS:ffff88806d100000(0000) knlGS:0000000000000000 [ 21.113612] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 21.114405] CR2: 000000000065c000 CR3: 000000005e58e006 CR4: 00000000001606e0 [ 21.115367] Call Trace: [ 21.115705] ? __alloc_pages_slowpath+0x21c0/0x21c0 [ 21.116362] alloc_pages_current+0xac/0x1e0 [ 21.116923] kmalloc_order+0x18/0x70 [ 21.117393] kmalloc_order_trace+0x18/0x110 [ 21.117949] packet_set_ring+0x9d5/0x1770 [ 21.118524] ? packet_rcv_spkt+0x440/0x440 [ 21.119094] ? lock_downgrade+0x620/0x620 [ 21.119646] ? __might_fault+0x177/0x1b0 [ 21.120177] packet_setsockopt+0x981/0x2940 [ 21.120753] ? __fget+0x2fb/0x4b0 [ 21.121209] ? packet_release+0xab0/0xab0 [ 21.121740] ? sock_has_perm+0x1cd/0x260 [ 21.122297] ? selinux_secmark_relabel_packet+0xd0/0xd0 [ 21.123013] ? __fget+0x324/0x4b0 [ 21.123451] ? selinux_netlbl_socket_setsockopt+0x101/0x320 [ 21.124186] ? selinux_netlbl_sock_rcv_skb+0x3a0/0x3a0 [ 21.124908] ? __lock_acquire+0x529/0x3200 [ 21.125453] ? selinux_socket_setsockopt+0x5d/0x70 [ 21.126075] ? __sys_setsockopt+0x131/0x210 [ 21.126533] ? packet_release+0xab0/0xab0 [ 21.127004] __sys_setsockopt+0x131/0x210 [ 21.127449] ? kernel_accept+0x2f0/0x2f0 [ 21.127911] ? ret_from_fork+0x8/0x50 [ 21.128313] ? do_raw_spin_lock+0x11b/0x280 [ 21.128800] __x64_sys_setsockopt+0xba/0x150 [ 21.129271] ? lockdep_hardirqs_on+0x37f/0x560 [ 21.129769] do_syscall_64+0x9f/0x450 [ 21.130182] entry_SYSCALL_64_after_hwframe+0x49/0xbe We should allocate with __GFP_NOWARN to handle this. Cc: Kal Conley <kal.conley@dectris.com> Cc: Andrey Konovalov <andreyknvl@google.com> Fixes: fc62814d ("net/packet: fix 4gb buffer limit due to overflow check") Signed-off-by:
Christoph Paasch <cpaasch@apple.com> Signed-off-by:
-
Bjorn Helgaas authored
[ Upstream commit fae846e2 ] The device ID alone does not uniquely identify a device. Test both the vendor and device ID to make sure we don't mistakenly think some other vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device ID table. No functional change intended. Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit e0aa6770 ] When a dual stack dccp listener accepts an ipv4 flow, it should not attempt to use an ipv6 header or inet6_iif() helper. Fixes: 3df80d93 ("[DCCP]: Introduce DCCPv6") Signed-off-by:
-
Bhadram Varka authored
[ Upstream commit a830405e ] Currently stmmac driver not copying the valid ethernet MAC address to MAC registers. This patch takes care of updating the MAC register with MAC address. Signed-off-by:
Bhadram Varka <vbhadram@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 4ef8c1c9 ] Ilan reported that sometimes nl80211 messages weren't working if the frames being transported got very large, which was really a problem for userspace-to-kernel messages, but prompted me to look at the code. Upon review, I found various places where variable-length data is transported in an nl80211 message but the message isn't allocated taking that into account. This shouldn't cause any problems since the frames aren't really that long, apart in one place where two (possibly very long frames) might not fit. Fix all the places (that I found) that get variable length data from the driver and put it into a message to take the length of the variable data into account. The 100 there is just a safe constant for the remaining message overhead (it's usually around 50 for most messages.) Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Christoffer Dall authored
[ Upstream commit ace6033e ] User space Android code identifies pixclock == 0 as a sign for emulation and will set the frame rate to 60 fps when reading this value, which is the desired outcome. Signed-off-by:
Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by:
Peter Maydell <peter.maydell@linaro.org> Signed-off-by:
Roman Kiryanov <rkir@google.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
-
Marcel Holtmann authored
commit 7c9cbd0b upstream. The function l2cap_get_conf_opt will return L2CAP_CONF_OPT_SIZE + opt->len as length value. The opt->len however is in control over the remote user and can be used by an attacker to gain access beyond the bounds of the actual packet. To prevent any potential leak of heap memory, it is enough to check that the resulting len calculation after calling l2cap_get_conf_opt is not below zero. A well formed packet will always return >= 0 here and will end with the length value being zero after the last option has been parsed. In case of malformed packets messing with the opt->len field the length value will become negative. If that is the case, then just abort and ignore the option. In case an attacker uses a too short opt->len value, then garbage will be parsed, but that is protected by the unknown option handling and also the option parameter size checks. Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Reviewed-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
-
Marcel Holtmann authored
commit af3d5d1c upstream. When doing option parsing for standard type values of 1, 2 or 4 octets, the value is converted directly into a variable instead of a pointer. To avoid being tricked into being a pointer, check that for these option types that sizes actually match. In L2CAP every option is fixed size and thus it is prudent anyway to ensure that the remote side sends us the right option size along with option paramters. If the option size is not matching the option type, then that option is silently ignored. It is a protocol violation and instead of trying to give the remote attacker any further hints just pretend that option is not present and proceed with the default values. Implementation following the specification and its qualification procedures will always use the correct size and thus not being impacted here. To keep the code readable and consistent accross all options, a few cosmetic changes were also required. Signed-off-by:
-
- 27 Mar, 2019 27 commits
-
-
Greg Kroah-Hartman authored
-
Arnd Bergmann authored
commit 6707ba01 upstream. The way that 'strncat' is used here raised a warning in gcc-8: drivers/net/wireless/ath/ath10k/wmi.c: In function 'ath10k_wmi_tpc_stats_final_disp_tables': drivers/net/wireless/ath/ath10k/wmi.c:4649:4: error: 'strncat' output truncated before terminating nul copying as many bytes from a string as its length [-Werror=stringop-truncation] Effectively, this is simply a strcat() but the use of strncat() suggests some form of overflow check. Regardless of whether this might actually overflow, using strlcat() instead of strncat() avoids the warning and makes the code more robust. Fixes: bc64d052 ("ath10k: debugfs support to get final TPC stats for 10.4 variants") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Baolin Wang authored
commit f25a646f upstream. Fix incorrect return value. Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Enric Balletbo i Serra authored
commit 5fb5caee upstream. Before this patch the enable signal was set before the PWM signal and vice-versa on power off. This sequence is wrong, at least, it is on the different panels datasheets that I checked, so I inverted the sequence to follow the specs. For reference the following panels have the mentioned sequence: - N133HSE-EA1 (Innolux) - N116BGE (Innolux) - N156BGE-L21 (Innolux) - B101EAN0 (Auo) - B101AW03 (Auo) - LTN101NT05 (Samsung) - CLAA101WA01A (Chunghwa) Signed-off-by:
Enric Balletbo i Serra <enric.balletbo@collabora.com> Acked-by:
Daniel Thompson <daniel.thompson@linaro.org> Acked-by:
Jingoo Han <jingoohan1@gmail.com> Acked-by:
Thierry Reding <thierry.reding@gmail.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Baolin Wang authored
commit 36d46cdb upstream. If we convert one large time values to rtc_time, in the original formula 'days * 86400' can be overflowed in 'unsigned int' type to make the formula get one incorrect remain seconds value. Thus we can use div_s64_rem() function to avoid this situation. Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
kehuanlin authored
commit 83dc7e3d upstream. Since the command type of UTRD in UFS 2.1 specification is the same with UFS 2.0. And it assumes the future UFS specification will follow the same definition. Signed-off-by:
kehuanlin <kehuanlin@pinecone.net> Reviewed-by:
Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Andrey Konovalov authored
commit 32fd87b3 upstream. When cleaning up the configurations, make sure we only free the number of configurations and interfaces that we could have allocated. Reported-by:
Andrey Konovalov <andreyknvl@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Peter Zijlstra authored
commit 3f329570 upstream. The current int_sqrt() computation is sub-optimal for the case of small @x. Which is the interesting case when we're going to do cumulative distribution functions on idle times, which we assume to be a random variable, where the target residency of the deepest idle state gives an upper bound on the variable (5e6ns on recent Intel chips). In the case of small @x, the compute loop: while (m != 0) { b = y + m; y >>= 1; if (x >= b) { x -= b; y += m; } m >>= 2; } can be reduced to: while (m > x) m >>= 2; Because y==0, b==m and until x>=m y will remain 0. And while this is computationally equivalent, it runs much faster because there's less code, in particular less branches. cycles: branches: branch-misses: OLD: hot: 45.109444 +- 0.044117 44.333392 +- 0.002254 0.018723 +- 0.000593 cold: 187.737379 +- 0.156678 44.333407 +- 0.002254 6.272844 +- 0.004305 PRE: hot: 67.937492 +- 0.064124 66.999535 +- 0.000488 0.066720 +- 0.001113 cold: 232.004379 +- 0.332811 66.999527 +- 0.000488 6.914634 +- 0.006568 POST: hot: 43.633557 +- 0.034373 45.333132 +- 0.002277 0.023529 +- 0.000681 cold: 207.438411 +- 0.125840 45.333132 +- 0.002277 6.976486 +- 0.004219 Averages computed over all values <128k using a LFSR to generate order. Cold numbers have a LFSR based branch trace buffer 'confuser' ran between each int_sqrt() invocation. Link: http://lkml.kernel.org/r/20171020164644.876503355@infradead.org Fixes: 30493cc9 ("lib/int_sqrt.c: optimize square root algorithm") Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Suggested-by:
Anshul Garg <aksgarg1989@gmail.com> Acked-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Joe Perches <joe@perches.com> Cc: David Miller <davem@davemloft.net> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michael Davidson <md@google.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Lanqing Liu authored
commit 43507825 upstream. On Spreadtrum's serial device, nearly all of interrupts would be cleared by hardware except timeout interrupt. This patch removed the operation of clearing all interrupt in irq handler, instead added an if statement to check if the timeout interrupt is supposed to be cleared. Wrongly clearing timeout interrupt would lead to uart data stay in rx fifo, that means the driver cannot read them out anymore. Signed-off-by:
Lanqing Liu <lanqing.liu@spreadtrum.com> Signed-off-by:
Chunyan Zhang <chunyan.zhang@spreadtrum.com> Signed-off-by:
-
Qiao Zhou authored
commit 6f44a0ba upstream. In current die(), the irq is disabled for __die() handle, not including the possible panic() handling. Since the log in __die() can take several hundreds ms, new irq might come and interrupt current die(). If the process calling die() holds some critical resource, and some other process scheduled later also needs it, then it would deadlock. The first panic will not be executed. So here disable irq for the whole flow of die(). Signed-off-by:
Qiao Zhou <qiaozhou@asrmicro.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Al Viro authored
commit 81be24d2 upstream. It's not hard to trigger a bunch of d_invalidate() on the same dentry in parallel. They end up fighting each other - any dentry picked for removal by one will be skipped by the rest and we'll go for the next iteration through the entire subtree, even if everything is being skipped. Morevoer, we immediately go back to scanning the subtree. The only thing we really need is to dissolve all mounts in the subtree and as soon as we've nothing left to do, we can just unhash the dentry and bugger off. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Wei Qiao authored
commit e1dc9b08 upstream. SPRD_TIMEOUT was 256, which is too small to wait until the status switched to workable in a while loop, so that the earlycon could not work correctly. Signed-off-by:
Wei Qiao <wei.qiao@spreadtrum.com> Signed-off-by:
-
Eric Dumazet authored
commit 5ea8ea2c upstream. Per listen(fd, backlog) rules, there is really no point accepting a SYN, sending a SYNACK, and dropping the following ACK packet if accept queue is full, because application is not draining accept queue fast enough. This behavior is fooling TCP clients that believe they established a flow, while there is nothing at server side. They might then send about 10 MSS (if using IW10) that will be dropped anyway while server is under stress. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Hui Wang authored
commit b5a236c1 upstream. Recently we found the audio jack detection stop working after suspend on many machines with Realtek codec. Sometimes the audio selection dialogue didn't show up after users plugged headhphone/headset into the headset jack, sometimes after uses plugged headphone/headset, then click the sound icon on the upper-right corner of gnome-desktop, it also showed the speaker rather than the headphone. The root cause is that before suspend, the codec already call the runtime_suspend since this codec is not used by any apps, then in resume, it will not call runtime_resume for this codec. But for some realtek codec (so far, alc236, alc255 and alc891) with the specific BIOS, if it doesn't run runtime_resume after suspend, all codec functions including jack detection stop working anymore. This problem existed for a long time, but it was not exposed, that is because when problem happens, if users play sound or open sound-setting to check audio device, this will trigger calling to runtime_resume (via snd_hda_power_up), then the codec starts working again before users notice this problem. Since we don't know how many codec and BIOS combinations have this problem, to fix it, let the driver call runtime_resume for all codecs in pm_resume, maybe for some codecs, this is not needed, but it is harmless. After a codec is runtime resumed, if it is not used by any apps, it will be runtime suspended soon and furthermore we don't run suspend frequently, this change will not add much power consumption. Fixes: cc72da7d ("ALSA: hda - Use standard runtime PM for codec power-save control") Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 98081ca6 upstream. Currently we deal with single codec and suspend codec callbacks for all S3, S4 and runtime PM handling. But it turned out that we want distinguish the call patterns sometimes, e.g. for applying some init sequence only at probing and restoring from hibernate. This patch slightly modifies the common PM callbacks for HD-audio codec and stores the currently processed PM event in power_state of the codec's device.power field, which is currently unused. The codec callback can take a look at this event value and judges which purpose it's being called. Signed-off-by:
-
Waiman Long authored
commit 71492580 upstream. Tetsuo Handa had reported he saw an incorrect "downgrading a read lock" warning right after a previous lockdep warning. It is likely that the previous warning turned off lock debugging causing the lockdep to have inconsistency states leading to the lock downgrade warning. Fix that by add a check for debug_locks at the beginning of __lock_downgrade(). Debugged-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Reported-by:
Waiman Long <longman@redhat.com> Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Myungho Jung authored
commit e20a2e9c upstream. When releasing socket, it is possible to enter hci_sock_release() and hci_sock_dev_event(HCI_DEV_UNREG) at the same time in different thread. The reference count of hdev should be decremented only once from one of them but if storing hdev to local variable in hci_sock_release() before detached from socket and setting to NULL in hci_sock_dev_event(), hci_dev_put(hdev) is unexpectedly called twice. This is resolved by referencing hdev from socket after bt_sock_unlink() in hci_sock_release(). Reported-by: syzbot+fdc00003f4efff43bc5b@syzkaller.appspotmail.com Signed-off-by:
Myungho Jung <mhjungk@gmail.com> Signed-off-by:
-
Hans Verkuil authored
commit f45f3f75 upstream. Control events can leak kernel memory since they do not fully zero the event. The same code is present in both v4l2-ctrls.c and uvc_ctrl.c, so fix both. It appears that all other event code is properly zeroing the structure, it's these two places. Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: syzbot+4f021cf3697781dbd9fb@syzkaller.appspotmail.com Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by:
-
zhangyi (F) authored
commit 674a2b27 upstream. All indirect buffers get by ext4_find_shared() should be released no mater the branch should be freed or not. But now, we forget to release the lower depth indirect buffers when removing space from the same higher depth indirect block. It will lead to buffer leak and futher more, it may lead to quota information corruption when using old quota, consider the following case. - Create and mount an empty ext4 filesystem without extent and quota features, - quotacheck and enable the user & group quota, - Create some files and write some data to them, and then punch hole to some files of them, it may trigger the buffer leak problem mentioned above. - Disable quota and run quotacheck again, it will create two new aquota files and write the checked quota information to them, which probably may reuse the freed indirect block(the buffer and page cache was not freed) as data block. - Enable quota again, it will invoke vfs_load_quota_inode()->invalidate_bdev() to try to clean unused buffers and pagecache. Unfortunately, because of the buffer of quota data block is still referenced, quota code cannot read the up to date quota info from the device and lead to quota information corruption. This problem can be reproduced by xfstests generic/231 on ext3 file system or ext4 file system without extent and quota features. This patch fix this problem by releasing the missing indirect buffers, in ext4_ind_remove_space(). Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
zhangyi (F) <yi.zhang@huawei.com> Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by:
-
Lukas Czerner authored
commit 372a03e0 upstream. Ext4 needs to serialize unaligned direct AIO because the zeroing of partial blocks of two competing unaligned AIOs can result in data corruption. However it decides not to serialize if the potentially unaligned aio is past i_size with the rationale that no pending writes are possible past i_size. Unfortunately if the i_size is not block aligned and the second unaligned write lands past i_size, but still into the same block, it has the potential of corrupting the previous unaligned write to the same block. This is (very simplified) reproducer from Frank // 41472 = (10 * 4096) + 512 // 37376 = 41472 - 4096 ftruncate(fd, 41472); io_prep_pwrite(iocbs[0], fd, buf[0], 4096, 37376); io_prep_pwrite(iocbs[1], fd, buf[1], 4096, 41472); io_submit(io_ctx, 1, &iocbs[1]); io_submit(io_ctx, 1, &iocbs[2]); io_getevents(io_ctx, 2, 2, events, NULL); Without this patch the 512B range from 40960 up to the start of the second unaligned write (41472) is going to be zeroed overwriting the data written by the first write. This is a data corruption. 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00009200 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 * 0000a000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 0000a200 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 With this patch the data corruption is avoided because we will recognize the unaligned_aio and wait for the unwritten extent conversion. 00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 * 00009200 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 * 0000a200 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 * 0000b200 Reported-by:
Frank Sorenson <fsorenso@redhat.com> Signed-off-by:
Lukas Czerner <lczerner@redhat.com> Signed-off-by:
-
Jiufei Xue authored
commit fa30dde3 upstream. We see the following NULL pointer dereference while running xfstests generic/475: BUG: unable to handle kernel NULL pointer dereference at 0000000000000008 PGD 8000000c84bad067 P4D 8000000c84bad067 PUD c84e62067 PMD 0 Oops: 0000 [#1] SMP PTI CPU: 7 PID: 9886 Comm: fsstress Kdump: loaded Not tainted 5.0.0-rc8 #10 RIP: 0010:ext4_do_update_inode+0x4ec/0x760 ... Call Trace: ? jbd2_journal_get_write_access+0x42/0x50 ? __ext4_journal_get_write_access+0x2c/0x70 ? ext4_truncate+0x186/0x3f0 ext4_mark_iloc_dirty+0x61/0x80 ext4_mark_inode_dirty+0x62/0x1b0 ext4_truncate+0x186/0x3f0 ? unmap_mapping_pages+0x56/0x100 ext4_setattr+0x817/0x8b0 notify_change+0x1df/0x430 do_truncate+0x5e/0x90 ? generic_permission+0x12b/0x1a0 This is triggered because the NULL pointer handle->h_transaction was dereferenced in function ext4_update_inode_fsync_trans(). I found that the h_transaction was set to NULL in jbd2__journal_restart but failed to attached to a new transaction while the journal is aborted. Fix this by checking the handle before updating the inode. Fixes: b436b9be ("ext4: Wait for proper transaction commit on fsync") Signed-off-by:
Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by:
Joseph Qi <joseph.qi@linux.alibaba.com> Cc: stable@kernel.org Signed-off-by:
-
Josh Poimboeuf authored
commit 0c671812 upstream. Objtool uses over 512k of stack, thanks to the hash table embedded in the objtool_file struct. This causes an unnecessarily large stack allocation and breaks users with low stack limits. Move the struct off the stack. Fixes: 042ba73f ("objtool: Add several performance improvements") Reported-by:
Vassili Karpov <moosotc@gmail.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/df92dcbc4b84b02ffa252f46876df125fb56e2d7.1552954176.git.jpoimboe@redhat.comSigned-off-by:
-
Chen Jie authored
commit 5a07168d upstream. The futex code requires that the user space addresses of futexes are 32bit aligned. sys_futex() checks this in futex_get_keys() but the robust list code has no alignment check in place. As a consequence the kernel crashes on architectures with strict alignment requirements in handle_futex_death() when trying to cmpxchg() on an unaligned futex address which was retrieved from the robust list. [ tglx: Rewrote changelog, proper sizeof() based alignement check and add comment ] Fixes: 0771dfef ("[PATCH] lightweight robust futexes: core") Signed-off-by:
Chen Jie <chenjie6@huawei.com> Signed-off-by:
-
Archer Yan authored
commit 47c25036 upstream. Insert Branch instruction instead of NOP to make sure assembler don't patch code in forbidden slot. In jump label function, it might be possible to patch Control Transfer Instructions(CTIs) into forbidden slot, which will generate Reserved Instruction exception in MIPS release 6. Signed-off-by:
Archer Yan <ayan@wavecomp.com> Reviewed-by:
Paul Burton <paul.burton@mips.com> [paul.burton@mips.com: - Add MIPS prefix to subject. - Mark for stable from v4.0, which introduced r6 support, onwards.] Signed-off-by:
-
Yasha Cherikovsky authored
commit 3f0a53bc upstream. This fixes booting with the combination of CONFIG_RELOCATABLE=y and CONFIG_MIPS_ELF_APPENDED_DTB=y. Sections that appear after the relocation table are not relocated on system boot (except .bss, which has special handling). With CONFIG_MIPS_ELF_APPENDED_DTB, the dtb is part of the vmlinux ELF, so it must be relocated together with everything else. Fixes: 069fd766 ("MIPS: Reserve space for relocation table") Signed-off-by:
Yasha Cherikovsky <yasha.che3@gmail.com> Signed-off-by:
-
Yifeng Li authored
commit 5f5f67da upstream. Timekeeping IRQs from CS5536 MFGPT are routed to i8259, which then triggers the "cascade" IRQ on MIPS CPU. Without IRQF_NO_SUSPEND in cascade_irqaction, MFGPT interrupts will be masked in suspend mode, and the machine would be unable to resume once suspended. Previously, MIPS IRQs were not disabled properly, so the original code appeared to work. Commit a3e6c1ef ("MIPS: IRQ: Fix disable_irq on CPU IRQs") uncovers the bug. To fix it, add IRQF_NO_SUSPEND to cascade_irqaction. This commit is functionally identical to 0add9c2f ("MIPS: Loongson-3: Add IRQF_NO_SUSPEND to Cascade irqaction"), but it forgot to apply the same fix to Loongson2. Signed-off-by:
Yifeng Li <tomli@tomli.me> Signed-off-by:
-
Jan Kara authored
commit d3ca4651 upstream. When truncate(2) hits IO error when reading indirect extent block the code just bugs with: kernel BUG at linux-4.15.0/fs/udf/truncate.c:249! ... Fix the problem by bailing out cleanly in case of IO error. CC: stable@vger.kernel.org Reported-by:
jean-luc malet <jeanluc.malet@gmail.com> Signed-off-by:
-
